Nissan Pathfinder (2022 year). Manual in english - page 24

 

  Index      Manuals     Nissan Pathfinder (2022 year). Manual in english

 

Search            copyright infringement  

 

 

 

 

 

 

 

 

 

 

 

Content      ..     22      23      24      25     ..

 

 

 

Nissan Pathfinder (2022 year). Manual in english - page 24

 

 

NOTE:

Turning on the ProPILOT Assist system
will turn on the I-BSI and I-LI system at
the same time. For additional informa-
tion, see “Intelligent Lane Intervention
(I-LI)” (P. 5-42).
Turning the BSW system off will deacti-
vate the I-BSI system at the same time.

LSD4262

For vehicles with the 12.3 inch (31.2 cm) display

5-66

Starting and driving

-------------------------------------------------------------------------------------------------------------------------------------------------------------

I-BSI SYSTEM LIMITATIONS

WARNING

Listed below are the system limitations
for the I-BSI system. Failure to operate
the vehicle in accordance with these
system limitations could result in seri-
ous injury or death.

The I-BSI system cannot detect all
vehicles under all conditions.

The radar sensors may not be able to
detect and activate I-BSI when cer-
tain objects are present such as:

Pedestrians, bicycles, or animals.

Vehicles such as motorcycles, low

height vehicles, or high ground
clearance vehicles.

Vehicles remaining in the detec-

tion zone when you accelerate
from a stop. For additional infor-
mation, see “BSI driving situa-
tions” (P. 5-68).

Oncoming vehicles.

A vehicle merging into an adjacent

lane at a speed approximately the
same as your vehicle.

A

vehicle

approaching

rapidly

from behind.

A vehicle which your vehicle over-

takes rapidly.

A vehicle that passes through the

detection zone quickly.

The radar sensors’ detection zone is
designed based on a standard lane
width. When driving in a wider lane,
the radar sensors may not detect ve-
hicles in an adjacent lane. When driv-
ing in a narrow lane, the radar sen-
sors may detect vehicles driving two
lanes away.

The radar sensors are designed to ig-
nore most stationary objects; how-
ever, objects such as guardrails,
walls, foliage and parked vehicles
may occasionally be detected. This is
a normal operation condition.

The following conditions may reduce
the ability of the radar to detect other
vehicles:

Severe weather

Road spray

Ice/frost/dirt

build-up

on

the

vehicle

Do not attach stickers (including
transparent material), install acces-
sories or apply additional paint near
the radar sensors. These conditions
may reduce the ability of the radar to
detect other vehicles.

The camera may not detect lane
markers in the following situations
and the I-BSI system may not oper-
ate properly.

On roads where there are multiple

parallel lane markers; lane mark-
ers that are faded or not painted
clearly; yellow painted lane mark-
ers; non-standard lane markers;
lane markers covered with water,
dirt, snow, etc.

On roads where discontinued lane

markers are still detectable.

On roads where there are sharp

curves.

On roads where there are sharply

contrasting objects, such as shad-
ows, snow, water, wheel ruts,
seams or lines remaining after
road repairs.

On roads where the traveling lane

merges or separates.

Starting and driving

5-67

-------------------------------------------------------------------------------------------------------------------------------------------------------------

When the vehicle’s traveling direc-

tion does not align with the lane
markers.

When traveling close to the ve-

hicle in front of you, which ob-
structs the lane camera unit de-
tection range.

When rain, snow or dirt adheres to

the windshield in front of a lane
camera unit.

When

the

headlights

are

not

bright due to dirt on the lens or if
aiming is not adjusted properly.

When strong light enters a lane

camera unit. (For example: light
directly shines on the front of the
vehicle at sunrise or sunset.)

When a sudden change in bright-

ness occurs. (For example: when
the vehicle enters or exits a tunnel
or under a bridge.)

Do not use the I-BSI system under the
following conditions because the
system may not function properly.

During bad weather (for example:

rain, fog, snow, etc.).

When driving on slippery roads,

such as on ice or snow, etc.

When driving on winding or un-

even roads.

When there is a lane closure due to

road repairs.

When driving in a makeshift or

temporary lane.

When driving on roads where the

lane width is too narrow.

When driving with a tire that is not

within normal tire conditions (e.g.,
tire wear, low tire pressure, instal-
lation of spare tire, tire chains,
nonstandard wheels).

When the vehicle is equipped with

non-original brake parts or sus-
pension parts.

When towing a trailer or other

vehicle.

Excessive noise (e.g., audio system
volume, open vehicle window) will in-
terfere with the chime sound, and it
may not be heard.

I-BSI DRIVING SITUATIONS

Indicator on

Indicator off

Indicator flashing

5-68

Starting and driving

-------------------------------------------------------------------------------------------------------------------------------------------------------------

Another vehicle approaching
from behind

Illustration 1: The side indicator light illumi-
nates if a vehicle enters the detection zone
from behind in an adjacent lane.

Illustration 2: If the driver activates the turn
signal then the system chimes a sound
(twice) and the side indicator light flashes.

Illustration 3: If the I-BSI system is on and
your vehicle approaches a lane marker
while another vehicle is in the detection
zone, the system chimes (three times) and
the side indicator light flashes. Then the
I-BSI system activates to help return the
vehicle back to the center of the driving
lane.

LSD2299

Illustration 1 – Approaching from behind

LSD2300

Illustration 2 – Approaching from

behind

LSD3775

Illustration 3 – Approaching from

behind

Starting and driving

5-69

-------------------------------------------------------------------------------------------------------------------------------------------------------------

NOTE:
• The radar sensors may not detect ve-

hicles which are approaching rapidly
from behind.

• If the driver activates the turn signal

before a vehicle enters the detection
zone, the side indicator light will flash
but no chime will sound when the
other vehicle is detected.

Overtaking another vehicle

Illustration 4: The side indicator light illumi-
nates if you overtake a vehicle and that
vehicle stays in the detection zone for ap-
proximately 3 seconds.

Illustration 5: If the driver activates the turn
signal while another vehicle is in the detec-
tion zone, then the system chimes (twice)
and the side indicator light flashes.

LSD2302

Illustration 4– Overtaking another

vehicle

LSD2303

Illustration 5– Overtaking another

vehicle

5-70

Starting and driving

-------------------------------------------------------------------------------------------------------------------------------------------------------------

Illustration 6: If the I-BSI system is on and
your vehicle approaches a lane marker
while another vehicle is in the detection
zone, the system chimes (three times) and
the side indicator light flashes. The I-BSI
system activates to help return the vehicle
back to the center of the driving lane.

NOTE:
• When overtaking several vehicles in a

row, the vehicles after the first vehicle
may not be detected if they are travel-
ing close together.

• The radar sensors may not detect

slower moving vehicles if they are
passed quickly.

Entering from the side

Illustration 7: The side indicator light illumi-
nates if a vehicle enters the detection zone
from either side.

NOTE:

The radar sensors may not detect a ve-
hicle which is traveling at about the
same speed as your vehicle when it en-
ters the detection zone.

LSD2072

Illustration 6– Overtaking another

vehicle

LSD2305

Illustration 7– Entering from the side

Starting and driving

5-71

-------------------------------------------------------------------------------------------------------------------------------------------------------------

Illustration 8: If the driver activates the turn
signal while another vehicle is in the detec-
tion zone, then the side indicator light
flashes and a chime will sound twice.

NOTE:

If the driver activates the turn signal be-
fore a vehicle enters the detection zone,
the side indicator light will flash but no
chime will sound when another vehicle is
detected.

Illustration 9: If the I-BSI system is on and
your vehicle approaches the lane marker
while another vehicle is in the detection
zone, the system chimes (three times) and
the side indicator light flashes. The I-BSI
system activates to help return the vehicle
back to the center of the driving lane.

Illustration 10: The I-BSI system will not op-
erate if your vehicle is on a lane marker
when another vehicle enters the detection
zone. In this case only the BSW system
operates.

LSD2308

Illustration 8– Entering from the side

SSD1094

Illustration 9– Entering from the side

LSD2051

Illustration 10: – Entering from the side

5-72

Starting and driving

-------------------------------------------------------------------------------------------------------------------------------------------------------------

NOTE:
• The radar sensors may not detect a ve-

hicle which is traveling at about the
same speed as your vehicle when it en-
ters the detection zone.

• I-BSI will not operate or will stop oper-

ating and only a warning chime will
sound under the following conditions:

– When the brake pedal is depressed.
– When the vehicle is accelerated dur-

ing I-BSI system operation.

– When steering quickly.
– When the ICC, I-FCW or AEB with Pe-

destrian Detection warnings sound.

– When the hazard warning flashers

are operated.

– When driving on a curve at a high

speed.

– When the BSW system is turned off.

SYSTEM TEMPORARILY
UNAVAILABLE

Under the following conditions, a chime will
sound, the following message will appear
in the vehicle information display and the
I-BSI system will be turned off automati-
cally. The I-BSI system will not be available
until the conditions no longer exist.

• “Not available Poor Road Conditions”

– When the VDC system (except TCS

function) or ABS operates.

• “Currently not available”

– When the VDC system is turned off.
– When the SNOW mode, or the MUD/

RUT mode or SAND mode (4WD mod-
els only) is selected

• “Unavailable High Cabin Temperature”:

If the vehicle is parked in direct sunlight
under

high

temperature

conditions

(over approximately 104°F (40°C)).

• “Unavailable Side Radar Obstruction”:

When side radar blockage is detected.

Turn off the I-BSI system and turn it on
again when the above conditions no lon-
ger exist.

SYSTEM MALFUNCTION

When the I-BSI system malfunctions, it will
be turned off automatically, a chime will
sound, and the “Not available System Mal-
function” warning message with the BSW
indicator (orange) will appear in the vehicle
information display.

Action to take:

Stop the vehicle in a safe location, place the
vehicle in the P (Park) position, turn the en-
gine off and restart the engine. If the “Not
available System Malfunction” warning
message with the BSW indicator (orange)
continues to be displayed, have the I-BSI
system checked. It is recommended you
visit a certified NISSAN dealer for this
service.

Starting and driving

5-73

-------------------------------------------------------------------------------------------------------------------------------------------------------------

SYSTEM MAINTENANCE

The two radar sensors

O

1

for the I-BSI sys-

tem are located near the rear bumper. Al-
ways keep the area near the radar sensors
clean.

The radar sensors may be blocked by tem-
porary ambient conditions such as splash-
ing water, mist or fog.

The blocked condition may also be caused
by objects such as ice, frost or dirt ob-
structing the radar sensors.

Check for and remove objects obstructing
the radar sensors.

Do not attach stickers (including transpar-
ent material), install accessories or apply
additional paint near the radar sensors.

Do not strike or damage the area around
the radar sensors.

It is recommended you visit a certified
NISSAN dealer if the area around the radar
sensors is damaged due to a collision.

The lane camera unit

O

2

for I-BSI system is

located above the inside mirror. To keep
the proper operation of I-BSI and prevent a
system malfunction, be sure to observe
the following:
• Always keep the windshield clean.
• Do not attach a sticker (including trans-

parent material) or install an accessory
near the camera unit.

• Do not place reflective materials, such as

white paper or a mirror, on the instru-
ment panel. The reflection of sunlight
may adversely affect the camera unit’s
capability of detecting the lane markers.

• Do not strike or damage the areas

around the camera unit. Do not touch the
camera lens or remove the screw located
on the camera unit. It is recommended
that you contact a certified NISSAN dealer
if the camera unit is damaged due to an
accident.

Radio frequency statement

For USA

FCC ID: LTQRN5TR

CAUTION TO USERS

Changes or modifications not expressly
approved by the party responsible for
compliance could void the user’s author-
ity to operate the equipment.

This device complies with Part 15 of the
FCC Rules and with the RSS of the Indus-
try Canada. Operation is subject to the
following two conditions:

1.

This device may not cause harmful in-
terference, and

2.

this device must accept any interfer-
ence received, including interference
that may cause undesired operation.

LSD4340

5-74

Starting and driving

-------------------------------------------------------------------------------------------------------------------------------------------------------------

For Canada

Model: RN5TR

IC: 3659A-RN5TR

This

device

complies

with

Industry

Canada licence-exempt RSS standard(s).
Operation is subject to the following two
conditions: (1) this device may not cause
interference, and (2) this device must ac-
cept any interference, including interfer-
ence that may cause undesired opera-
tion of the device.

WARNING

Failure to follow the warnings and in-
structions for proper use of the RCTA
system could result in serious injury or
death.

The RCTA system is not a replace-
ment for proper driving procedures
and is not designed to prevent con-
tact with vehicles or objects. When
backing out of a parking space, al-
ways use the side and rear mirrors
and turn and look in the direction
your vehicle will move. Never rely
solely on the RCTA system.

Do no use the RCTA system when
towing a trailer. The system may not
function properly.

The RCTA system will assist you when
backing out from a parking space. When
the vehicle is in reverse, the system is de-
signed to detect other vehicles approach-
ing from the right or left of the vehicle. If the
system detects cross traffic, it will alert you.

REAR CROSS TRAFFIC ALERT (RCTA)

Starting and driving

5-75

-------------------------------------------------------------------------------------------------------------------------------------------------------------

RCTA SYSTEM OPERATION

1

Side BSW/RCTA Indicator Light

The RCTA system can help alert the driver
of an approaching vehicle when the driver
is backing out of a parking space.

When the shift position is in R (Reverse) and
the vehicle speed is less than approxi-
mately 5 mph (8 km/h), the RCTA system is
operational.

If the radar detects an approaching vehicle
from either side, the system chimes (once)
and the side BSW/RCTA indicator light
flashes on the side the vehicle is approach-
ing from.

LSD4313

For vehicles with the 7 inch (18 cm) display

5-76

Starting and driving

-------------------------------------------------------------------------------------------------------------------------------------------------------------

LSD4314

For vehicles with the 12.3 inch (31.2 cm) display

LSD2216

Starting and driving

5-77

-------------------------------------------------------------------------------------------------------------------------------------------------------------

The RCTA system uses radar sensors

O

1

installed on both sides near the rear bum-
per to detect an approaching vehicle.

The radar sensors

O

1

can detect an ap-

proaching vehicle from up to approxi-
mately 66 ft. (20 m) away.

HOW TO ENABLE/DISABLE THE
RCTA SYSTEM

LSD4157

LSD4266

For vehicles with the 7 inch (18 cm) display

5-78

Starting and driving

-------------------------------------------------------------------------------------------------------------------------------------------------------------

Perform the following steps to enable or
disable the RCTA system.

1. Press the

button until “Settings” dis-

plays in the vehicle information display.
Use the scroll dial to select “Driver Assis-
tance.” Then press the OK button.

2. Select “Rear Cross Traffic Alert” and press

the OK button to turn the system on or
off.

NOTE:
• When enabling/disabling the system,

the system setting will be retained
even if the engine is restarted.

LSD4267

For vehicles with the 12.3 inch (31.2 cm) display

Starting and driving

5-79

-------------------------------------------------------------------------------------------------------------------------------------------------------------

RCTA SYSTEM LIMITATIONS

WARNING

Listed below are the system limitations
for the RCTA system. Failure to operate
the vehicle in accordance with these
system limitations could result in seri-
ous injury or death.

Always check surroundings and turn
to check what is behind you before
backing up. The radar sensors detect
approaching (moving) vehicles. The
radar sensors cannot detect every
object such as:

Pedestrians,

bicycles,

motor-

cycles, animals or child-operated
toy vehicles

A vehicle that is passing at speeds

greater than approximately 19
mph (30 km/h)

A vehicle that is passing at speeds

lower than approximately 5 mph
(8 km/h)

The radar sensors may not detect
approaching vehicles in certain situ-
ations:

Illustration

O

A

: When a vehicle

parked next to you obstructs the
beam of the radar sensor.

Illustration

O

B

: When the vehicle is

parked

in

an

angled

parking

space.

Illustration

O

C

: When the vehicle is

parked on inclined ground.

Illustration

O

D

:

When

an

ap-

proaching vehicle turns into your
vehicle's parking lot aisle.

LSD3195

5-80

Starting and driving

-------------------------------------------------------------------------------------------------------------------------------------------------------------

Illustration

O

E

: When the angle

formed by your vehicle and ap-
proaching vehicle is small

The following conditions may reduce
the ability of the radar to detect other
vehicles:

Severe weather

Road spray

Ice/frost/snow/dirt build-up on

the vehicle

Do not attach stickers (including
transparent material), install acces-
sories or apply additional paint near
the radar sensors. These conditions
may reduce the ability of the radar to
detect other vehicles

Excessive noise (e.g., audio system
volume, open vehicle window) will in-
terfere with the chime sound, and it
may not be heard.

NOTE:

In the case of several vehicles approach-
ing in a row (Illustration 1) or in the oppo-
site direction (Illustration 2), a chime may
not be sounded by the RCTA system af-
ter the first vehicle passes the sensors.

LSD2043

Illustration 1

LSD2044

Illustration 2

Starting and driving

5-81

-------------------------------------------------------------------------------------------------------------------------------------------------------------

 

 

 

 

 

 

 

Content      ..     22      23      24      25     ..