Nissan Pathfinder (2022 year). Manual in english

ROOF RACK (if so equipped)

WARNING

•

Always install the crossbars onto the
roof side rails before loading cargo of
any kind. Loading cargo directly onto
the roof side rails or the vehicle’s roof
may cause vehicle damage.

•

Roof rack cross bars should be evenly
distributed.

•

Do not exceed maximum roof rack
crossbars load capacity and always
distribute the load uniformly.

•

Heavy loading of the crossbars has
the potential to affect the vehicle
stability and handling during sudden
or unusual handling maneuvers.

•

Properly secure all cargo with ropes
or straps to help prevent it from slid-
ing or shifting. In a sudden stop or
collision,

unsecured

cargo

could

cause personal injury.

•

Drive extra carefully when the vehicle
is loaded at or near the cargo carry-
ing capacity, especially if the signifi-
cant portion of that load is carried on
the crossbars.

CAUTION

•

Use care when placing or removing
items from the roof rack. If you can-
not comfortably lift the items onto
the roof rack from the ground, use a
ladder or a stool.

Do not apply any load directly to the roof
side rails

. Crossbars

must be in-

stalled

before

applying

load/cargo/

luggage to the roof of the vehicle.
Genuine NISSAN accessory crossbars may
be available through a NISSAN dealer. It is
recommended that you visit a NISSAN
dealer for additional information.

The service load capacity for the roof side
rails is 165 lbs. (74 kg.), however do not ex-
ceed the crossbars load capacity.

Be careful that your vehicle does not ex-
ceed the Gross Vehicle Weight Rating
(GVWR) or its Gross Axle Weight Rating
(GAWR front and rear).

For additional information regarding GVWR
and GAWR, refer to:
• F.M.V.S.S. or C.V.M.S.S. certification label (lo-

cated on the driver’s door pillar).

Installing Crossbars (if so
equipped)

WARNING

•

It is recommended that you have the
roof rack crossbars installed by a
NISSAN dealer.

•

Protect the painted area on the ve-
hicle roof under the crossbars by
placing a piece of cloth under the
cross

bars

prevent

scratch

damage.

•

Make

sure

the

moonroof

(if

equipped) is in the closed position
during the installation process.

LIC4202

2-110

Instruments and controls

-------------------------------------------------------------------------------------------------------------------------------------------------------------

POWER WINDOWS

WARNING

•

Make sure that all passengers have
their hands, etc., inside the vehicle
while it is in motion and before clos-
ing the windows. Use the window
lock switch to prevent unexpected
use of the power windows.

•

To help avoid risk of injury or death
through unintended operation of the
vehicle and/or its systems, including
entrapment in windows or inadver-
tent door lock activation, do not
leave children, people who require
the assistance of others or pets unat-
tended in your vehicle. Additionally,
the temperature inside a closed ve-
hicle on a warm day can quickly be-
come high enough to cause a signifi-
cant risk of injury or death to people
and pets.

The power windows operate when the ig-
nition switch is placed in the ON position or
for a period of time after the ignition switch
is placed in the OFF position. If the driver's
or passenger's door is opened during this
period of time, the power to the windows is
canceled.

Driver's side power window
switch

The driver's side control panel is equipped
with switches to open or close all of the
windows.

To open a window, push the switch to the
detent and continue to hold down until the
desired window position is reached. To
close a window, pull the switch to the de-
tent and continue to hold up until the de-
sired window position is reached.

Locking rear passengers'
windows

When the window lock button is pushed
(the indicator illuminates), the rear passen-
gers’ windows cannot be operated with the
rear passengers’ power window switch.
The rear passengers’ windows can only be
operated with the main switch (driver side
switches). To cancel the passenger’s win-
dow lock, push the window lock button
again.

LIC4727

1. Window lock button

2. Left rear passenger side switch

3. Driver’s side switch

4. Power door lock/unlock switch

5. Front passenger side switch

6. Right rear passenger side switch

WINDOWS

Instruments and controls

2-111

-------------------------------------------------------------------------------------------------------------------------------------------------------------

Front passenger's power window
switch

The passenger's window switch operates
only the corresponding passenger's win-
dow. To open the window partially, push the
switch down

lightly until the desired

window position is reached. To close the
window partially, pull the switch up

until

the desired window position is reached.

Rear power window switch

The rear power window switches open or
close only the corresponding windows. To
open the window, push the switch and hold
it down

. To close the window, pull the

switch up

Automatic operation

To fully open a window equipped with au-
tomatic

operation,

push

the

window

switch down to the second detent and re-
lease it; it need not be held. The window
automatically opens all the way. To stop
the window, lift the switch up while the win-
dow is opening.

Auto-reverse function

The auto-reverse function can be acti-
vated when a window is closed by auto-
matic operation.

LIC4728

LIC4729

LIC4730

2-112

Instruments and controls

-------------------------------------------------------------------------------------------------------------------------------------------------------------

Depending on the environment or driv-
ing conditions, the auto-reverse func-
tion may be activated if an impact or
load similar to something being caught
in the window occurs.

WARNING

There are some small distances imme-
diately

before

the

closed

position

which cannot be detected. Make sure
that all passengers have their hands,
etc., inside the vehicle before closing
the window.

If the vehicle's battery is disconnected, re-
placed, or jump started, the power window
auto-reverse function may not operate
properly. If this occurs, please contact the
dealer to re-initialize the power window
auto-reverse system.

If the control unit detects something
caught in a window equipped with auto-
matic operation, as it is closing, the window
will be immediately lowered.

When power window switch does
not operate

If the power window automatic function
(closing only) does not operate properly,
perform the following procedure to initial-
ize the power window system:

1. Place the ignition switch in the ON position.

2. Open the window more than halfway by

operating the power window switch.

3. Pull the power window switch and hold it

to close the window, and then hold the
switch more than 3 seconds after the
window is closed.

4. Release the power window switch. Op-

erate the window by the automatic
function to confirm the initialization is
complete. The power window automati-
cally opens or closes depending on if
the automatic down or up function is
selected.

5. Perform steps 2 through 4 above for

other windows.

If the power window function does not op-
erate properly after performing the above
procedure have the system checked and
repaired. It is recommended that you visit a
NISSAN dealer for this service.

REAR DOOR SUNSHADE (if so
equipped)

The rear door sunshade is located within
the rear doors at the base of the window.
• To raise the sunshade, pull up the center

tab

• Hook the sunshade slots onto the tabs

extending from the top of the window
frame

LIC4169

Instruments and controls

2-113

-------------------------------------------------------------------------------------------------------------------------------------------------------------

CAUTION

•

Do not release the rear door sun-
shade during operation. This could
damage the sunshade or cause
injury.

•

Do not forcefully pull the sunshade.
Doing so may elongate the sun-
shade. This could cause improper op-
eration

could

damage

the

sunshade.

•

Do not place objects on or near the
rear sunshade. This could cause im-
proper operation or could damage
the sunshade.

NOTE:
To avoid damage to the sunshade,
please note the following:
• Do not pull or push the sunshade, other

than upwards.

• Do not pull or push the sunshade with

the sunshade hung on the hooks.

• Do not allow liquids or objects on the

storing area of the sunshade.

WARNING

•

In an accident you could be thrown
from the vehicle through an open
moonroof. Always use seat belts and
child restraints.

•

Do not allow anyone to stand up or
extend any portion of their body of
the moonroof opening while the ve-
hicle is in motion or while the moon-
roof is closing.

CAUTION

•

Remove water drops, snow, ice or
sand from the moonroof before
opening.

•

Do not place any heavy object on the
moonroof or surrounding area.

AUTOMATIC MOONROOF AND
SUNSHADE

Sliding sunshade and moonroof

When the sunshade switch is pushed to
the OPEN position

, the sunshade open.

(If the sunshade starts to open from the
position between close and half open, the
sunshade will stop half. When the switch is
pushed again, the sunshade will open fully.)
When the moonroof switch is pushed to
the OPEN position

, the moonroof opens

to the comfort mode position. (If the sun-
shade is close, the sunshade will open half

LIC4759

POWER MOONROOF (if so equipped)

2-114

Instruments and controls

-------------------------------------------------------------------------------------------------------------------------------------------------------------

first. When the switch is pushed again, the
moonroof will open fully.)

When the moonroof switch is pushed to
the CLOSE position

, the moonroof will

automatically close. When the sunshade
switch is pushed to the CLOSE position

the sunshade will close. (If the sunshade
starts to close from the position between
full and half open, the sunshade will stop
half. When the switch is pushed again, the
sunshade will close fully. However, if the
moonroof is open or tilted up, the sun-
shade will not close beyond half.)

To stop the sunshade or moonroof during
the operation, push the moonroof switch
to either of the OPEN

, CLOSE

or UP

position.

Tilting the moonroof

To tilt up the moonroof, push the moonroof
switch to the UP position

. To tilt down

the moonroof, push the switch to the
CLOSE position

Comfort mode

This is the position used when driving with
the moonroof open. When driving with the
moonroof fully open, wind noise may be
very loud. Use the comfort mode position
when driving.

Auto-reverse function

WARNING

There are some small distances imme-
diately

before

the

closed

position

which cannot be detected. Make sure
that all passengers have their hands,
etc., inside the vehicle before closing
the moonroof and sunshade.

The auto-reverse function enables the
moonroof and sunshade to automatically
reverse when something is caught in the
moonroof and sunshade as it is closing.
When the control unit detects an obstacle,
the moonroof and sunshade will open
immediately.

Depending on the environment or driving
conditions, the auto-reverse function may
activate if an impact or load similar to
something being caught in the moonroof
and sunshade occurs.

If the auto-reverse function activates con-
secutively or the battery is discharged, the
moonroof and sunshade may not close
properly. In this case, push and hold the
switch to the CLOSE position

to close

the moonroof.

If the moonroof switch does not
operate

If the moonroof and sunshade do not op-
erate properly, perform the following pro-
cedure to initialize the operation system.

1. If the moonroof and sunshade are open,

close them fully by repeatedly pushing
the moonroof switch to the CLOSE

and

position.

2. Push and hold the moonroof switch to

the CLOSE

position for 10 seconds.

3. After the moonroof and sunshade

move slightly to the closed position and
then move back a little, release the
moonroof switch.

4. Push and hold the moonroof switch to

the CLOSE

position, and the glass

and shade will move.

5. Release the moonroof switch. Then the

moonroof and sunshade will fully open
and then fully close.

6. Check if the moonroof switch operates

normally.

Instruments and controls

2-115

-------------------------------------------------------------------------------------------------------------------------------------------------------------

WARNING

The driver is always responsible for op-
erating the moonroof properly, includ-
ing the operation by all passengers.
Failure to follow the warnings and in-
structions for proper use of the moon-
roof could result in serious injury or
death.

•

Do not allow children to operate the
moonroof. Improper operation by
children may cause an accident. If
children or others get caught in the
moonroof, it could cause serious
injury.

•

To help avoid risk of injury or death
through unintended operation of the
moonroof, place the ignition switch
in the OFF position when leaving the
vehicle, and do not leave children and
the Intelligent Key inside the vehicle.

•

Do not activate the auto-reverse
function intentionally. If hands or
face, etc. get caught in the moonroof,
it could cause serious injury.

CAUTION

•

Do not place objects (such as news-
papers, handkerchiefs, etc.) on the
sunshade when it is extending or re-
tracting causing improper operation
or damage to the sunshade.

•

Do not push the sunshade arm with
your hands, etc., as this may deform
it. Improper operation or damage to
the sunshade may result.

•

Do not put any object into the sun-
shade inlet port as this may result in
improper operation or damage the
sunshade.

•

Do not hang any object on the arm
rail as this may result in improper op-
eration or damage the sunshade.

•

Do not forcefully pull the sunshade.
Doing so may elongate the sun-
shade. Improper operation or dam-
age to the sunshade may result.

If the moonroof does not operate properly
after performing the procedure above,
have your vehicle checked by a NISSAN
dealer.

䊊

The interior light can be turned on re-
gardless of door position. The light will
go off after a period of time unless the
ignition switch is placed in the ON posi-
tion when any door is opened.

䊊

The interior lights can be set to operate
when the doors are opened. To turn off
the interior lights when a door is open,
push the switch, the interior lights will
not illuminate, regardless of door posi-
tion.

LIC4033

INTERIOR LIGHTS

2-116

Instruments and controls

-------------------------------------------------------------------------------------------------------------------------------------------------------------

The lights will go off when the ignition
switch is placed in the ON position, or
the driver's door is closed and locked.
The lights will also go off after a period
of time when the doors are open.

NOTE:

The footwell lights and step lights (if so
equipped) illuminate when the driver
and passenger doors are opened re-
gardless of the interior light switch posi-
tion. These lights will turn off automati-
cally after a period of time while doors
are open to prevent the battery from be-
coming discharged.

CAUTION

Do not use for extended periods of time
with the engine stopped. This could re-
sult in a discharged battery.

MAP LIGHTS

To turn the map lights on, push the
switches. To turn them off, push the
switches again.

CAUTION

Do not use for extended periods of time
with the engine stopped. This could re-
sult in a discharged battery.

PERSONAL LIGHTS

To turn on the personal lights, push and
release the switch

To turn off the personal lights, push and
release the switch

LIC4035

LIC1413

Instruments and controls

2-117

-------------------------------------------------------------------------------------------------------------------------------------------------------------

CARGO LIGHT

The cargo light on the overhead trim has a
three-position switch. To operate, push the
switch to the desired position.

䊊

ON: The light is illuminated.

䊊

DOOR: The light illuminates when the
liftgate is opened. The light turns off
when the liftgate is closed.

䊊

OFF: The light does not illuminate re-
gardless of liftgate position or lock
status.

CAUTION

Do not use for extended periods of time
with the engine stopped. This could re-
sult in a discharged battery.

The HomeLink® Universal Transceiver pro-
vides a convenient way to consolidate the
functions of up to three individual hand-
held transmitters into one built-in device.

HomeLink® Universal Transceiver:
• Will operate most radio frequency de-

vices such as garage doors, gates, home
and office lighting, entry door locks and
security systems.

• Is powered by your vehicle's battery. No

separate batteries are required. If the
vehicle's battery is discharged or is dis-
connected, HomeLink® will retain all
programming.

When the HomeLink® Universal Trans-
ceiver is programmed, retain the original
transmitter for future programming pro-
cedures (Example: new vehicle pur-
chases). Upon sale of the vehicle, the
programmed

HomeLink®

Universal

Transceiver buttons should be erased for
security purposes. For additional infor-
mation, see “Programming HomeLink®”
(P. 2-119).

SIC2063A

HOMELINK® UNIVERSAL
TRANSCEIVER (if so equipped)

2-118

Instruments and controls

-------------------------------------------------------------------------------------------------------------------------------------------------------------

WARNING

•

Your vehicle's engine should be
turned off while programming the
HomeLink® Universal Transceiver. For
additional information, see “Push-
button ignition switch” (P. 5-13). Do
not breathe exhaust gases; they con-
tain colorless and odorless carbon
monoxide. Carbon monoxide is dan-
gerous. It can cause unconscious-
ness or death.

•

Do not use the HomeLink® Universal
Transceiver with any garage door
opener that lacks safety stop and re-
verse features as required by federal
safety standards. (These standards
became effective for opener models
manufactured after April 1, 1982.) A
garage door opener which cannot
detect an object in the path of a clos-
ing garage door and then automati-
cally stop and reverse does not meet
current federal safety standards. Us-
ing a garage door opener without
these features increases the risk of
serious injury or death.

•

During the programming procedure
your garage door or security gate will
open and close (if the transmitter is
within range). Make sure that people
or objects are clear of the garage
door,

gate,

etc.,

that

you

are

programming.

PROGRAMMING HOMELINK®

If you have any questions or are having
difficulty programming your HomeLink®
buttons, refer to the HomeLink® web site at:
www.homelink.com or call 1-800-355-3515.

NOTE:

Place the ignition switch in the ON posi-
tion (without starting the engine) when
programming HomeLink®. It is also rec-
ommended that a new battery be placed
in the hand-held transmitter of the de-
vice being programmed to HomeLink®
for quicker programming and accurate
transmission of the radio frequency.

1. Position the end of your hand-held

transmitter 1–3 in (2–8 cm) away from
the HomeLink® surface, keeping the
HomeLink® indicator light

in view.

LIC2365

Instruments and controls

2-119

-------------------------------------------------------------------------------------------------------------------------------------------------------------

2. Using both hands, simultaneously press

and hold the desired HomeLink® button
and hand-held transmitter button. DO
NOT release until the HomeLink® indica-
tor light

flashes slowly and then rap-

idly. When the indicator light flashes rap-
idly, both buttons may be released. (The
rapid

flashing

indicates

successful

programming.)

NOTE:

Some devices may require you to replace
Step 2 with the cycling procedure noted
in “Programming HomeLink® for Cana-
dian

customers

and

gate

openers”

(P. 2-121).

3. Press

and

hold

the

programmed

HomeLink® button and observe the indi-
cator light.

• If the indicator light

is solid/

continuous, programming is com-
plete

and your device should activate

when

the

HomeLink®

button

pressed and released.

• If the indicator light

blinks

rapidly

for 2 seconds and then turns to a
solid/continuous

light,

continue

with Steps 4-6

for a rolling code de-

vice. A second person may make the
following steps easier. Use a ladder or
other device. Do not stand on your ve-
hicle to perform the next steps.

4. At the receiver located on the garage

door opener motor in the garage, locate
the “learn” or “smart” button (the name
and color of the button may vary by
manufacturer but it is usually located
near where the hanging antenna wire is
attached to the unit). If there is difficulty
locating the button, reference the ga-
rage door opener’s manual.

5. Press and release the “learn” or “smart”

button.

NOTE:
Once the button is pressed, you have
approximately 30 seconds to initiate
the next step.

6. Return to the vehicle and firmly press

and hold the trained HomeLink® button
for 2 seconds and release. Repeat the
“press/hold/release” sequence up to
three times to complete the training
process. HomeLink® should now acti-
vate your rolling code equipped device.

7. If you have any questions or are having

difficulty programming your HomeLink®
buttons, refer to the HomeLink® web site at:
www.homelink.com or call 1-800-355-3515.

LIC4095

2-120

Instruments and controls

-------------------------------------------------------------------------------------------------------------------------------------------------------------

PROGRAMMING HOMELINK® FOR
CANADIAN CUSTOMERS AND GATE
OPENERS

Canadian radio-frequency laws require
transmitter signals to “time-out” (or quit)
after several seconds of transmission –
which may not be long enough for
HomeLink® to pick up the signal during
training. Similar to this Canadian law, some
U.S. gate operators are designed to “tim-
eout” in the same manner.

If you live in Canada or you are having diffi-
culties training a gate operator

garage

door opener by using the “Training” proce-
dures,

replace

“Programming HomeLink®”

step 2

with the following:

NOTE:

When

programming

garage

door

opener, etc., unplug the device during
the “cycling” process to prevent possible
damage to the garage door opener
components.

1. For additional information, see “Pro-

gramming HomeLink®” step 1 (P. 2-119).

2. Using both hands, simultaneously press

and hold the desired HomeLink® button
and the hand-held transmitter button.
During training, your hand-held trans-
mitter may automatically stop transmit-
ting. Continue to press and hold the de-
sired HomeLink® button while you press
and re-press (“cycle”) your hand-held
transmitter every 2 seconds until the
frequency signal has been learned. The
HomeLink® indicator light will flash
slowly and then rapidly after several
seconds upon successful training. DO
NOT release until the HomeLink® indica-
tor light flashes slowly and then rapidly.
When the indicator light flashes rapidly,
both buttons may be released. The rapid
flashing indicates successful training.
Proceed with “Programming HomeLink®”
step 3 to complete.
If the device was unplugged during the
programming procedure, remember to
plug it back in when programming is
completed.

OPERATING THE HOMELINK®
UNIVERSAL TRANSCEIVER

The HomeLink® Universal Transceiver, after
it is programmed, can be used to activate
the programmed device. To operate, sim-
ply press and release the appropriate pro-
grammed HomeLink® Universal Trans-
ceiver button. The amber indicator light will
illuminate

while

the

signal

being

transmitted.

For convenience, the hand-held transmit-
ter of the device may also be used at any
time.

PROGRAMMING TROUBLE-
DIAGNOSIS

If the HomeLink® does not quickly learn the
hand-held transmitter information:
• Replace the hand-held transmitter bat-

teries with new batteries.

• Position the hand-held transmitter with

its battery area facing away from the
HomeLink® surface.

• Press and hold both the HomeLink® and

hand-held transmitter buttons without
interruption.

Instruments and controls

2-121

-------------------------------------------------------------------------------------------------------------------------------------------------------------

• Position the hand-held transmitter 1 - 3 in

(26 - 76 mm) away from the HomeLink®
surface. Hold the transmitter in that posi-
tion for up to 15 seconds. If HomeLink® is
not programmed within that time, try
holding the transmitter in another posi-
tion – keeping the indicator light in view at
all times.

If you have any questions or are having
difficulty programming your HomeLink®
buttons, refer to the HomeLink® web site at:
www.homelink.com or call 1-800-355-3515.

CLEARING THE PROGRAMMED
INFORMATION

The following procedure clears the pro-
grammed information from both buttons.
Individual buttons cannot be cleared. How-
ever, individual buttons can be repro-
grammed. For additional information, see
“Reprogramming a single HomeLink® but-
ton” (P. 2-122).

To clear all programming:

1. Press and hold the two outer HomeLink®

buttons until the indicator light begins to
flash in approximately 10 seconds. Do
not hold for longer than 20 seconds.

2. Release both buttons.

HomeLink® is now in the programming
mode and can be programmed at any
time

beginning

with

“Programming

HomeLink®” - Step 1.

REPROGRAMMING A SINGLE
HOMELINK® BUTTON

To reprogram a HomeLink® Universal
Transceiver button, complete the following:

1. Press and hold the desired HomeLink®

button.

DO NOT

release the button.

2. The indicator light will begin to flash af-

ter 20 seconds. Without releasing the
HomeLink® button, proceed with “Pro-
gramming HomeLink®” - Step 1.

For

questions

comments,

contact

HomeLink®

at:

www.homelink.com

1–800–355–3515 (except Mexico).

The HomeLink® Universal Transceiver but-
ton has now been reprogrammed. The new
device can be activated by pressing the
HomeLink® button that was just pro-
grammed. This procedure will not affect any
other programmed HomeLink® buttons.

IF YOUR VEHICLE IS STOLEN

If your vehicle is stolen, you should change
the codes of any non-rolling code device
that

has

been

programmed

into

HomeLink®. Consult the Owner's Manual of
each device or call the manufacturer or
dealer of those devices for additional
information.

When your vehicle is recovered, you will
need to reprogram the HomeLink® Uni-
versal Transceiver with your new trans-
mitter information.

FCC Notice:

For USA:

This device complies with Part 15 of the
FCC Rules. Operation is subject to the fol-
lowing two conditions: (1) This device
may not cause harmful interference, and
(2) this device must accept any interfer-
ence received, including interference
that may cause undesired operation.

NOTE:

Changes or modifications not expressly
approved by the party responsible for
compliance could void the user’s author-
ity to operate the equipment.

2-122

Instruments and controls

-------------------------------------------------------------------------------------------------------------------------------------------------------------

Nissan Pathfinder (2022 year). Manual in english - page 14