Nissan Qashqai (2022 year). Manual in english - page 20

 

  Index      Manuals     Nissan Qashqai (2022 year). Manual in english

 

Search            copyright infringement  

 

 

 

 

 

 

 

 

 

 

 

Content      ..     18      19      20      21     ..

 

 

 

Nissan Qashqai (2022 year). Manual in english - page 20

 

 

WAF0054X

.

The distance to the vehicle ahead

changes automatically according to

the vehicle speed. The higher the

vehicle speed, the longer the distance.

.

The distance setting will remain at the

current setting even if the engine is

restarted.

HOW TO ENABLE/DISABLE THE

STEERING ASSIST

Use the following methods to enable or

disable the steering assist.

Starting and driving

5-73

-------------------------------------------------------------------------------------------------------------------------------------------------------------

5-74

Starting and driving

WAF0055X

1. Steering-wheel-mounted control (left)
2. Vehicle information display
3. Steering assist switch

NOTE:

.

When the steering assist switch is

used to turn the system on or off,

the system remembers the setting

even if the ignition switch is cycled.

The switch must be pushed again to

change the setting to on or off.

.

The steering assist switch changes

the status of the “Steering Assist”

selection made in the “Settings”

screen in the vehicle information

display.

Steering assist switch:

To turn the steering assist on or off, push

the steering assist switch

on the

instrument panel.

Setting in the vehicle information dis-

play:

1. Press the

button on the

steering wheel

until “Settings” ap-

pears in the vehicle information dis-

play

and then press “OK” button.

2. Use the

button

to select “Driver

Assistance.” Then press the “OK” but-

ton

.

3. Use the

button

to select “Driving

Aids.” Then press the “OK” button

.

4. Select “Steering Assist” and press the

“OK” button

.

NOTE:

.

When the Cruise screen is displayed

on the vehicle information display,

press the “OK” button on the steer-

ing wheel to call up the “Driving Aids”

setting display.

.

When enabling/disabling the system

through the vehicle information dis-

play, the system retains the current

settings even if the engine is re-

started.

-------------------------------------------------------------------------------------------------------------------------------------------------------------

HOW TO CANCEL THE PROPILOT

ASSIST SYSTEM

To cancel the ProPILOT assist system, use

one of the following methods:

.

Push the CANCEL switch.

.

Tap the brake pedal (except at a

standstill).

.

Push the ProPILOT assist switch to

turn the system off. The ProPILOT

assist status indicator will turn off.

When the ProPILOT assist system is

canceled while the vehicle is stopped,

the electronic parking brake is automati-

cally activated.

WARNING

To prevent the vehicle from moving

or rolling unexpectedly, which could

result in serious personal injury or

property damage, before exiting the

vehicle make sure to push the Pro-

PILOT assist switch to turn the sys-

tem off, place the shift lever in the P

(Park) position, and turn the engine

off.

INTELLIGENT CRUISE CONTROL

(ICC)

WARNING

Failure to follow the warnings and

instructions for proper use of the ICC

system could result in serious injury

or death.

.

The ICC system is only an aid to

assist the driver and is not a

collision warning or avoidance

device. It is recommended for

highway use only and it is not

intended for city driving. It is the

driver’s responsibility to stay

alert, drive safely, and be in con-

trol of the vehicle at all times.

.

There are limitations to the ICC

system capability. The ICC system

does not function in all driving,

traffic, weather, and road condi-

tions. It is the driver’s responsi-

bility to stay alert, drive safely,

keep the vehicle in the traveling

lane, and be in control of the

vehicle at all times.

.

Always observe posted speed

limits and do not set the speed

over them.

.

The ICC system does not react to

stationary and slow moving vehi-

cles.

.

Always drive carefully and atten-

tively when using the ICC system.

Read and understand the Owner’s

Manual thoroughly before using

the ICC system. To avoid serious

injury or death, do not rely on the

system to prevent accidents or to

control the vehicle’s speed in

emergency situations. Do not

use the ICC system except in

appropriate road and traffic con-

ditions.

ICC system operation

The ICC system is designed to maintain a

selected distance from the vehicle in front

of you and can reduce the speed to

match a slower vehicle ahead. The sys-

tem decelerates the vehicle as necessary

and if the vehicle ahead comes to a stop,

the vehicle decelerates to a standstill.

However, the ICC system can only apply

up to 40% of the vehicle’s total braking

power. This system should only be used

when traffic conditions allow vehicle

speeds to remain fairly constant or when

vehicle speeds change gradually. If a

vehicle moves into the traveling lane

Starting and driving

5-75

-------------------------------------------------------------------------------------------------------------------------------------------------------------

5-76

Starting and driving

ahead or if a vehicle traveling ahead

rapidly decelerates, the distance between

vehicles may become closer because the

ICC system cannot decelerate the vehicle

quickly enough. If this occurs, the ICC

system sounds a warning chime and

blinks the system display to notify the

driver to take necessary action.
The ICC system cancels and a warning

chime sounds if the speed is below

approximately 15 MPH (24 km/h) and a

vehicle is not detected ahead.
The ICC system operates as follows:

.

When there are no vehicles traveling

ahead, the ICC system maintains the

speed set by the driver. The set speed

range is between approximately 20

and 90 MPH (32 and 144 km/h).

.

When there is a vehicle traveling

ahead, the ICC system adjusts the

speed to maintain the distance, se-

lected by the driver, from the vehicle

ahead. If the vehicle ahead comes to a

stop, the vehicle decelerates to a

standstill. Once your vehicle stops,

the ICC system keeps the vehicle

stopped.

.

When your vehicle is stopped for less

than 3 seconds and the vehicle ahead

begins to move, your vehicle will start

moving again automatically.

.

When your vehicle is at a standstill for

more than 3 seconds and the vehicle

ahead begins to accelerate, push the

RES+ switch or lightly depress the

accelerator pedal. The ICC system

starts to follow the vehicle ahead.

.

When the vehicle traveling ahead

moves to a different traveling lane,

the ICC system accelerates and main-

tains vehicle speed up to the set

speed.

The ICC system does not control vehicle

speed or warn you when you approach

stationary and slow moving vehicles. You

must pay attention to vehicle operation

to maintain proper distance from vehicles

ahead when approaching toll gates or

traffic congestion.

SSD0254

When driving on the freeway at a set

speed and approaching a slower traveling

vehicle ahead, the ICC system adjusts the

speed to maintain the distance, selected

by the driver, from the vehicle ahead. If

the vehicle ahead changes lanes or exits

the freeway, the ICC system accelerates

and maintains the speed up to the set

speed. Pay attention to the driving opera-

tion to maintain control of the vehicle as

it accelerates to the set speed.
The vehicle may not maintain the set

speed on winding or hilly roads. If this

occurs, you will have to manually control

the vehicle speed.
Normally when controlling the distance to

-------------------------------------------------------------------------------------------------------------------------------------------------------------

a vehicle ahead, the system automatically

accelerates or decelerates your vehicle

according to the speed of the vehicle

ahead.
Depress the accelerator to properly ac-

celerate your vehicle when acceleration is

required for a lane change. Depress the

brake pedal when deceleration is required

to maintain a safe distance to the vehicle

ahead due to sudden braking or if a

vehicle cuts in. Always stay alert when

using the ICC system.

WAF0057X

System set display with no vehicle detected ahead

No vehicle detected ahead:

The driver sets the desired vehicle speed

based on the road conditions. The ICC

system maintains the set vehicle speed,

similar to standard cruise control, as long

as no vehicle is detected in the lane

ahead. The ICC system displays the set

speed.

WAF0058X

System set display with vehicle ahead

Vehicle detected ahead:

When a vehicle is detected in the lane

ahead, the ICC system decelerates the

vehicle by controlling the throttle and

applying the brakes to match the speed

of a slower vehicle ahead. The ICC system

then controls the vehicle speed based on

the speed of the vehicle ahead to main-

tain the driver selected distance.

NOTE:

.

The stop lights of the vehicle come

on when braking is performed by

the ICC system.

.

When the brake is applied by the

system, a noise may be heard. This is

not a malfunction.

Starting and driving

5-77

-------------------------------------------------------------------------------------------------------------------------------------------------------------

5-78

Starting and driving

When the ICC system detects a vehicle

ahead, the vehicle ahead detection indi-

cator and the speed control status in-

d i c a t o r ( d i s t a n c e c o n t r o l m o d e )

illuminates (solid green

).

Vehicle ahead stops:

When the vehicle ahead decelerates to

stop, your vehicle decelerates to a stand-

still. Once your vehicle stops, the ICC

system automatically applies the brakes

to keep the vehicle stopped. When your

vehicle is at a standstill, the “(RES+) Press

to start” message is displayed on the

vehicle information display.

NOTE:
When your vehicle stops for less than 3

seconds, your vehicle will automatically

follow the vehicle as it accelerates from

a stop.
Vehicle ahead accelerates:

When your vehicle is stopped and the

vehicle ahead begins to accelerate, push

the RES+ switch or lightly depress the

accelerator pedal. The ICC system starts

to follow the vehicle ahead.

Vehicle ahead not detected:

When a vehicle is no longer detected

ahead, the ICC system gradually acceler-

ates your vehicle to resume the pre-

viously set vehicle speed. The ICC

system then maintains the set speed.
When a vehicle is no longer detected, the

vehicle ahead detection indicator turns

off and speed control status indicator

(maintain speed control mode) illumi-

nates (green outline

).

The ICC system gradually accelerates to

the set speed, but you can depress the

accelerator pedal to quickly accelerate.

When a vehicle is no longer detected and

your vehicle is traveling under approxi-

mately 15 MPH (24 km/h), the ICC system

automatically cancels.

WAF0059X

When passing another vehicle, the set

speed indicator

flashes when the

vehicle speed exceeds the set speed.

The vehicle ahead detection indicator

turns off when the area ahead of the

vehicle is open. When the pedal is re-

leased, the vehicle returns to the pre-

viously set speed. Even though your

vehicle speed is set in the ICC system,

you can depress the accelerator pedal

when it is necessary to accelerate your

vehicle rapidly.

-------------------------------------------------------------------------------------------------------------------------------------------------------------

Cut-in detection

If a vehicle moves into your traveling lane

near your vehicle, the ICC system may

inform the driver by flashing the vehicle

ahead detection indicator.

Approach warning

If your vehicle comes closer to the vehicle

ahead due to rapid deceleration of that

vehicle or if another vehicle cuts in, the

system warns the driver with the chime

and ICC system display. Decelerate by

depressing the brake pedal to maintain a

safe vehicle distance if:

.

The chime sounds.

.

The vehicle ahead detection indicator

and set distance indicator blink.

.

You judge it necessary to maintain a

safe distance.

The warning chime may not sound in

some cases when there is a short dis-

tance between vehicles. Some examples

are:

.

When the vehicles are traveling at the

same speed and the distance be-

tween vehicles is not changing.

.

When the vehicle ahead is traveling

faster and the distance between ve-

hicles is increasing.

.

When a vehicle cuts in near your

vehicle.

The warning chime will not sound when:

.

Your vehicle approaches other vehi-

cles that are parked or moving slowly.

.

The accelerator pedal is depressed,

overriding the system.

NOTE:
The approach warning chime may

sound and the system display may

flash when the radar sensor detects

objects on the side of the vehicle or on

the side of the road. This may cause the

ICC system to decelerate or accelerate

the vehicle. The radar sensor may de-

tect these objects when the vehicle is

driven on winding, narrow, or hilly roads

or when the vehicle is entering or

exiting a curve. In these cases, you will

have to manually control the proper

distance ahead of your vehicle.
Also, the sensor sensitivity can be af-

fected by vehicle operation (steering

maneuver or driving position in the

lane) or traffic or vehicle conditions

(for example, if a vehicle is being driven

with some damage).

Acceleration when passing

When the ICC system is engaged above

44 mph (70 km/h) and following a slower

vehicle (below ICC set speed), and the

turn signal is activated to the left, the ICC

system will automatically start to accel-

erate the vehicle to help initiate passing

on the left and will begin to reduce the

distance to vehicle directly ahead. Only

the left side turn signal operates this

feature. As the driver steers the vehicle

and moves into the passing lane, if no

vehicle is detected ahead the ICC system

will continue to accelerate to the ICC

system set speed. If another vehicle is

detected ahead, then the vehicle will

accelerate up to the following speed of

that vehicle. If the vehicle is not steered

into the left lane to pass, the acceleration

will stop after a short time and regain the

set following distance. Acceleration can

be stopped at any point by depressing

the brake pedal or the CANCEL switch on

the steering wheel.

ICC system limitations

WARNING

Listed below are the system limita-

tions for the ICC system. Failure to

operate the vehicle in accordance

Starting and driving

5-79

-------------------------------------------------------------------------------------------------------------------------------------------------------------

5-80

Starting and driving

with these system limitations could

result in serious injury or death:

.

The ICC system is primarily in-

tended for use on straight, dry,

open roads with light traffic. It is

not advisable to use the ICC

system in city traffic or congested

areas.

.

The ICC system will not adapt

automatically to road conditions.

This system should be used in

evenly flowing traffic. Do not use

the system on roads with sharp

curves or on icy roads, in heavy

rain or in fog.

.

As there is a performance limit to

the distance control function,

never rely solely on the ICC sys-

tem. This system does not correct

careless, inattentive or absent-

minded driving or overcome poor

visibility in rain, fog, or other bad

weather. Decelerate the vehicle

speed by depressing the brake

pedal, depending on the distance

to the vehicle ahead and the

surrounding circumstances in or-

der to maintain a safe distance

between vehicles.

.

When the ICC system automati-

cally brings the vehicle to a stop,

your vehicle can automatically

accelerate if the vehicle is

stopped for less than approxi-

mately 3 seconds. Be prepared

to stop your vehicle if necessary.

.

Always pay attention to the op-

eration of the vehicle and be

ready to manually control the

proper following distance. The

ICC system may not be able to

maintain the selected distance

between vehicles (following dis-

tance) or selected vehicle speed

under some circumstances.

.

The system may not detect the

vehicle in front of you in certain

road or weather conditions. To

avoid accidents, never use the ICC

system under the following con-

ditions:
— On roads with heavy, high-

speed traffic or sharp curves

— On slippery road surfaces

such as on ice or snow, etc.

— During bad weather (rain, fog,

snow, etc.)

— When rain, snow or dirt adhere

to the bumper around the

distance sensor

— On steep downhill roads (the

vehicle may go beyond the set

vehicle speed and frequent

braking may result in over-

heating the brakes)

— On repeated uphill and down-

hill roads

— When traffic conditions make

it difficult to keep a proper

distance between vehicles be-

cause of frequent accelera-

tion or deceleration

— Interference by other radar

sources.

.

In some road or traffic conditions,

a vehicle or object can unexpect-

edly come into the sensor detec-

tion zone and cause automatic

braking. Always stay alert and

avoid using the ICC system where

not recommended in this warn-

ing section.

The ICC system will not detect the

following objects:

.

Stationary or slow moving vehicles

.

Pedestrians or objects in the roadway

.

Oncoming vehicles in the same lane

-------------------------------------------------------------------------------------------------------------------------------------------------------------

.

Motorcycles traveling offset in the

travel lane

The following are some conditions in

which the radar sensor cannot properly

detect a vehicle ahead and the system

may not operate properly:

.

When the sensor detection is reduced

(conditions such as rain, snow, fog,

dust storms, sandstorms, and road

spray from other vehicles)

.

Driving on a steep downhill slope or

roads with sharp curves

.

Driving on a bumpy road surface, such

as an uneven dirt road

.

If dirt, ice, snow or other material is

covering the radar sensor area

.

A complicated-shaped vehicle such as

a car carrier trailer or flatbed truck/

trailer is near the vehicle ahead.

.

Interference by other radar sources

.

When excessively heavy baggage is

loaded in the rear seat or cargo area

of your vehicle.

The ICC system is designed to automati-

cally check the radar sensor’s operation

within the limitations of the system
The detection zone of the radar sensor is

limited. A vehicle ahead must be in the

detection zone for the ICC system to

maintain the selected distance from the

vehicle ahead. A vehicle ahead may move

outside of the detection zone due to its

position within the same lane of travel.

Motorcycles may not be detected in the

same lane ahead if they are traveling

offset from the center line of the lane. A

vehicle that is entering the lane ahead

may not be detected until the vehicle has

completely moved into the lane.
If this occurs, the ICC system may warn

you by blinking the system indicator and

sounding the chime. The driver may have

to manually control the proper distance

away from the vehicle traveling ahead.
The ICC system (with ProPILOT assist)

uses a multi-sensing front camera. The

following are some conditions in which

the camera may not properly detect a

vehicle and detection of a vehicle ahead

may be delayed:

.

Poor visibility (conditions such as rain,

snow, fog, dust storms, sandstorms,

and road spray from other vehicles)

.

The camera area of the windshield is

fogged up or covered with dirt, water

drops, ice, snow, etc.

.

Strong light (for example, sunlight or

high beams from oncoming vehicles)

enters the front camera

.

A sudden change in brightness occurs

(for example, when the vehicle enters

or exits a tunnel or shaded area or

lightning flashes)

Starting and driving

5-81

-------------------------------------------------------------------------------------------------------------------------------------------------------------

5-82

Starting and driving

SSD0252

SSD0253

When driving on some roads, such as

winding, hilly, curved, narrow roads, or

roads which are under construction, the

radar sensor may detect vehicles in a

different lane, or may temporarily not

detect a vehicle traveling ahead. This

may cause the ICC system to decelerate

or accelerate the vehicle.
The detection of vehicles may also be

affected by vehicle operation (steering

maneuver or traveling position in the

lane, etc.) or vehicle condition.
If this occurs, the ICC system may warn

you by blinking the system indicator and

sounding the chime unexpectedly. You

will have to manually control the proper

distance away from the vehicle traveling

ahead.

Automatic cancellation

The following are conditions in which the

ICC system may be temporarily unavail-

able. In these instances, the ICC system

may not cancel and may not be able to

maintain the selected following distance

from the vehicle ahead.

Condition A:

Under the following conditions, the ICC

system is automatically canceled. A chime

will sound and the system will not be able

to be set:

-------------------------------------------------------------------------------------------------------------------------------------------------------------

.

Any door is open.

.

The driver’s seat belt is not fastened.

.

The vehicle ahead is not detected and

your vehicle is traveling below the

speed of 15 MPH (24 km/h).

.

Your vehicle has been stopped by the

ICC system for approximately 3 min-

utes or longer.

.

The shift lever is not in the D (Drive)

position or manual shift mode.

.

The electronic parking brake is ap-

plied.

.

The VDC system is turned off.

.

The AEB applies harder braking

.

VDC (including the traction control

system) operates.

.

A wheel slips.

.

When distance measurement be-

comes impaired due to adhesion of

dirt or obstruction to the sensor.

.

When the radar signal is temporarily

interrupted.

Action to take:

When the conditions listed above are no

longer present, turn the system off using

the ProPILOT Assist switch. Turn the

ProPILOT Assist system back on to use

the system.

NOTE:
When the ICC system is canceled under

the following conditions at a standstill,

the electronic parking brake is automa-

tically activated:

.

Any door is open.

.

The driver’s seat belt is not fastened.

.

Your vehicle has been stopped by

the ICC system for approximately 3

minutes or longer.

.

The shift lever is not in the D (Drive)

position or manual shift mode.

.

The VDC system is turned off.

.

When distance measurement be-

comes impaired due to adhesion of

dirt or obstruction to the sensor.

.

When the radar signal is temporarily

interrupted.

Condition B:

When the radar sensor of the front

bumper is covered with dirt or is ob-

structed, the ICC system will automati-

cally be canceled.
The chime will sound and the “Forward

Driving Aids Temporarily Disabled Front

Sensor Blocked” or “Unavailable: Front

Radar Obstruction” warning message will

appear in the vehicle information display.

Action to take:

If the warning message appears, stop the

vehicle in a safe place, place the shift lever

in the P (Park) position, and turn the

engine off. When the radar signal is

temporarily interrupted, clean the sensor

area of the front bumper and restart the

engine. If the “Forward Driving Aids Tem-

porarily Disabled Front Sensor Blocked” or

“Unavailable: Front Radar Obstruction”

warning message continues to be dis-

played, have the system checked. It is

recommended that you visit a NISSAN

dealer for this service.

Condition C:

When driving on roads with limited road

structures or buildings (for example, long

bridges, deserts, snow fields, driving next

to long walls), the system may illuminate

the system warning light and display the

“Forward Driving Aids Temporarily Dis-

abled Front Sensor Blocked” or “Unavail-

able: Front Radar Obstruction” warning

message.

Action to take:

When the above driving conditions no

longer exist, turn the system back on.

Starting and driving

5-83

-------------------------------------------------------------------------------------------------------------------------------------------------------------

5-84

Starting and driving

ICC system malfunction

If the ICC system malfunctions, it will be

turned off automatically, a chime will

sound, and the speed control status

warning (orange) will illuminate.

Action to take:

If the warning illuminates, stop the vehicle

in a safe place. Turn the engine off, restart

the engine and set the ICC system again.

If it is not possible to set the ICC system or

the warning stays on, it may be a

malfunction. Although the normal driving

can be continued, the ICC system should

be inspected. It is recommended that you

visit a NISSAN dealer for this service.

ICC sensor maintenance

The radar sensor is located on the front of

the vehicle.
To keep the ICC system operating prop-

erly, be sure to observe the following:

.

Always keep the sensor area clean.

.

Do not strike or damage the areas

around the sensor.

.

Do not attach a sticker (including

transparent material) or install an

accessory near the sensor. This could

cause failure or malfunction.

.

Do not attach metallic objects near

the sensor area (brush guard, etc.).

This could cause failure or malfunc-

tion.

.

Do not alter, remove, or paint the front

bumper.

Before customizing or restoring the front

bumper, it is recommended that you visit

a NISSAN dealer.
The camera sensor is located above the

inside mirror.
To keep the proper operation of the

systems and prevent a system malfunc-

tion, be sure to observe the following:

.

Always keep the windshield clean.

.

Do not attach a sticker (including

transparent material) or install an

accessory near the camera unit.

.

Do not place reflective materials, such

as white paper or a mirror, on the

instrument panel. The reflection of

sunlight may adversely affect the

camera unit’s capability of detecting

the lane markers.

.

Do not strike or damage the areas

around the camera unit. Do not touch

the camera lens or remove the screw

located on the camera unit.

If the camera unit is damaged due to an

accident, it is recommended that you visit

a NISSAN dealer.

STEERING ASSIST

WARNING

Failure to follow the warnings and

instructions for proper use of the

steering assist could result in serious

injury or death.

.

The steering assist is not a repla-

cement for proper driving proce-

dures and is not designed to

correct careless, inattentive or

absent-minded driving. The

steering assist will not always

steer the vehicle to keep it in the

lane. It is not designed to prevent

loss of control. It is the driver’s

responsibility to stay alert, drive

safely, keep the vehicle in the

traveling lane, and be in control

of the vehicle at all times.

.

As there is a performance limit to

the steering assist’s capability,

never rely solely on the system.

The steering assist does not func-

tion in all driving, traffic, weather,

and road conditions. Always drive

safely, pay attention to the op-

eration of the vehicle, and manu-

a l l y c o n t r o l y o u r v e h i c l e

appropriately.

-------------------------------------------------------------------------------------------------------------------------------------------------------------

.

The steering assist is intended for

use on well-developed freeways

or highways with gentle (moder-

ate) curves. To avoid risk of an

accident,do not use this system

on local or non-highway roads.

.

The steering assist only steers

the vehicle to maintain its posi-

tion in the center of a lane. The

vehicle will not steer to avoid

objects in the road in front of

the vehicle or to avoid a vehicle

moving into your lane.

.

It is the driver’s responsibility to

stay alert, drive safely, keep the

vehicle in the traveling lane, and

be in control of the vehicle at all

times. Never take your hands off

the steering wheel when driving.

Always keep your hands on the

steering wheel and drive your

vehicle safely.

.

Always drive carefully and atten-

tively when using the steering

assist. Read and understand the

Owner’s Manual thoroughly be-

fore using the steering assist. To

avoid serious injury or death, do

not rely on the system to prevent

accidents or to control the vehi-

cle’s speed in emergency situa-

tions. Do not use the steering

assist except in appropriate road

and traffic conditions.

Steering assist operation

The steering assist controls the steering

system to help keep your vehicle near the

center of the lane when driving. The

steering assist is combined with the

Intelligent Cruise Control (ICC) system.

For additional information, see “Intelligent

Cruise Control (ICC)” (P.5-75).
The steering assist can be activated when

the following conditions are met:

.

The ICC system is activated.

.

Lane markers on both sides are clearly

detected.

.

A vehicle ahead is detected (when the

vehicle is driven at speeds under 37

MPH (60 km/h)).

.

The driver grips the steering wheel.

.

The vehicle is driven at the center of

the lane.

.

The turn signals are not operated.

.

The windshield wiper is not operated

in the high speed operation (the

steering assist function is disabled

after the wiper operates for approxi-

mately 10 seconds).

WAF0062X

Steering assist display and indica-

tors

1. Steering assist status indicator/ warn-

ing
Displays the status of the steering

assist by the color of the indicator/

warning

.

Steering assist status indicator

(gray): Steering assist standby

.

Steering assist status indicator

(green): Steering assist active

.

Steering assist status indicator (or-

ange): Steering assist malfunction

2. Steering assist indicator

Indicates the status of the steering

Starting and driving

5-85

-------------------------------------------------------------------------------------------------------------------------------------------------------------

5-86

Starting and driving

assist by the color of the indicator

.

Steering assist indicator (gray):

Steering assist standby

.

Steering assist indicator (green):

Steering assist active

.

Steering assist indicator (orange):

Steering assist malfunction

3. Lane marker indicator

Indicates whether the system detects

the lane marker

.

Lane marker indicator (gray): Lane

markers not detected

.

Lane marker indicator (green): Lane

markers detected

.

Lane marker indicator (orange):

Lane departure is detected

When the steering assist is in operation,

the steering assist status indicator

, the

steering assist indicator

, and the lane

marker indicator

on the vehicle infor-

mation display turn green. A chime

sounds when the steering assist initially

activates.
When the steering assist deactivates, the

steering assist status indicator

, the

steering assist indicator

, and the lane

marker indicator

on the vehicle infor-

mation display turn gray and a chime

sounds twice.

Intelligent Lane Intervention (I-LI)

When a curve or strong cross wind

exceeds the capabilities of the Steering

Assist and your vehicle approaches either

the left or the right side of the traveling

lane, a warning chime sounds and the I-LI

indicator light (orange) on the instrument

panel flashes to alert the driver. Then, the

I-LI system automatically applies the

brakes for a short period of time to help

assist the driver to return the vehicle to

the center of the traveling lane. This

action is in addition to any Steering Assist

actions. For more information, see “Intel-

ligent Lane Intervention (I-LI)” (P.5-40).

-------------------------------------------------------------------------------------------------------------------------------------------------------------

WAO0002X

Hands on detection

When the Steering assist is activated, it

monitors the driver’s steering wheel op-

eration.
If the steering wheel is not operated or

the driver takes his/her hands off the

steering wheel for a period of time, the

warning (1) appears in the vehicle infor-

mation display.
If the driver does not operate the steering

wheel after the warning has been dis-

played, an audible alert sounds and the

warning flashes in the vehicle information

display, followed by a quick brake appli-

cation to request the driver to take

control of the vehicle again.
If the driver still does not respond, the

ProPILOT assist turns on the hazard

flasher and slows the vehicle to a com-

plete stop.
The driver can cancel the deceleration at

any time by steering, braking, accelerat-

ing, or operating the ProPILOT assist

switch.

WARNING

Steering assist is not a system for a

hands-free driving. Always keep your

hands on the steering wheel and

drive your vehicle safely. Failure to

do so could cause a collision result-

ing in serious personal injury or

death.

NOTE:
If the driver lightly touches (instead of

firmly grips) the steering wheel, the

steering torque sensor may not detect

the driver’s hand(s) on the steering

wheel and a sequence of warnings

may occur. When the driver holds and

operates the steering wheel again, the

warnings turn off.

Starting and driving

5-87

-------------------------------------------------------------------------------------------------------------------------------------------------------------

5-88

Starting and driving

Steering assist limitations

WARNING

.

In the following situations, the

camera may not detect lane mar-

kers correctly or may detect lane

markers incorrectly and the

steering assist may not operate

properly:
— When driving on roads where

there are multiple parallel

lane markers, lane markers

that are faded or not painted

clearly, non-standard lane

markers, or lane markers cov-

ered with water, dirt, snow,

etc.

— When driving on roads with

discontinued lane markers

— When driving on roads with a

widening or narrowing lane

width

— When driving on roads where

there are multiple lanes or

unclear lane markers due to

road construction

— When driving on roads where

there are sharply contrasting

objects, such as shadows,

snow, water, wheel ruts,

seams, or lines remaining

after road repairs (the steer-

ing assist could detect these

items as lane markers)

— When driving on roads where

the traveling lane merges or

separates

.

Do not use the steering assist

under the following conditions

because the system may not

properly detect lane markers.

Doing so could cause a loss of

vehicle control and result in an

accident.
— During bad weather (rain, fog,

snow, dust, etc.)

— When rain, snow, sand, etc., is

thrown up by the wheels of

other vehicles

— When dirt, oil, ice, snow, water,

or another object adheres to

the camera unit

— When the lens of the camera

unit is foggy

— When strong light (for exam-

ple, sunlight or high beams

from oncoming vehicles)

shines on the camera

— When the headlights are not

bright due to dirt on the lens

or the headlights are off in

tunnels or darkness

— When a sudden change in

brightness occurs (for exam-

ple, when the vehicle enters or

exits a tunnel or is under a

bridge)

— When driving on roads where

the traveling lane merges or

separates or where there are

temporary lane markers be-

cause of road construction

— When there is a lane closure

due to road repairs

— When driving on a bumpy road

surface, such as an uneven

dirt road

— When driving on sharp curves

or winding roads

— When driving on repeated up-

hill and downhill roads

.

Do not use the steering assist

under the following conditions

because the system will not op-

erate properly:
— When driving with a tire that is

not within normal tire condi-

-------------------------------------------------------------------------------------------------------------------------------------------------------------

 

 

 

 

 

 

 

Content      ..     18      19      20      21     ..