Nissan Titan (2022 year). Manual in english - page 32

 

  Index      Manuals     Nissan Titan (2022 year). Manual in english

 

Search            copyright infringement  

 

 

 

 

 

 

 

 

 

 

 

Content      ..     30      31      32      33     ..

 

 

 

Nissan Titan (2022 year). Manual in english - page 32

 

 

Under some driving or climate conditions,
occasional brake squeak, squeal or other
noise may be heard. Occasional brake
noise during light to moderate stops is nor-
mal and does not affect the function or
performance of the brake system.

Proper brake inspection intervals should
be followed.

For additional information on

the appropriate maintenance schedule re-
garding brake inspections, see "Mainte-
nance schedules" (P. 9-7).

If any electrical equipment does not oper-
ate, check for an open fuse.

Fuses are used in the passenger and en-
gine compartment. Spare fuses are pro-
vided and can be found in the passenger
compartment fuse box.

When installing a fuse make sure the fuse is
installed in the fuse box securely.

ENGINE COMPARTMENT

WARNING

Never use a fuse of higher or lower am-
perage rating than that specified on
the fuse box cover. This could damage
the electrical system or electronic con-
trol units or cause a fire.

If any electrical equipment does not come
on, check for an open fuse.

1. Be sure the ignition switch and the head-

light switch are OFF.

2. Open the engine hood.

LDI2385

LDI2962

5.6L 8 cylinder (VK56VD engine model)

FUSES

8-24

Do-it-yourself

3. Remove the fuse box cover by pushing

the tab and lifting the cover up.

4. Remove the fuse with the fuse puller.

The fuse puller is located in the center of
the

fuse

block

in

the

passenger

compartment.

5. If the fuse is open

O

A

, replace it with a

new fuse

O

B

.

6. If a new fuse also opens, have the elec-

trical system checked and repaired. It is
recommended that you visit a NISSAN
dealer for this service.

Fusible links

If the electrical equipment does not oper-
ate and fuses are in good condition, check
the fusible links. If any of these fusible links
are melted, replace with only Genuine
NISSAN parts.

LDI3073

5.6L 8 cylinder (VK56VD engine model)

(non-XD model)

LDI3074

5.6L 8 cylinder (VK56VD engine model)

(XD model)

LDI0456

Do-it-yourself

8-25

PASSENGER COMPARTMENT

WARNING

Never use a fuse of higher or lower am-
perage rating than that specified on
the fuse box cover. This could damage
the electrical system or electronic con-
trol units or cause a fire.

If any electrical equipment does not oper-
ate, check for an open fuse.

1. Be sure the ignition switch and the head-

light switch are OFF.

2. Open the glove box.

3. Remove the fuse box cover.

4. Locate the fuse that needs to be

replaced.

5. Remove the fuse with the fuse puller

O

A

.

6. If the fuse is open

O

B

, replace it with an

equivalent good fuse

O

C

.

7. Push the fuse box cover to install.

If a new fuse also opens, have the electrical
system checked and repaired. It is recom-
mended that you visit a NISSAN dealer for
this service.

LDI2883

LDI2884

LDI2760

8-26

Do-it-yourself

CAUTION

Be careful not to allow children to swal-
low the battery or removed parts.

NISSAN INTELLIGENT KEY®

Replace the battery in the Intelligent Key as
follows:

1. Remove the mechanical key from the

Intelligent Key.

2. Insert a small flathead screwdriver

O

A

into the slit

O

B

of the corner and twist it

to separate the upper part from the
lower part. Place a cloth over the screw-
driver to protect the casing.

LDI2001

BATTERY REPLACEMENT

Do-it-yourself

8-27

3. Replace the battery with a new one.

Recommended

battery:

CR2032

or

equivalent.

• Do not touch the internal circuit and

electric terminals as doing so could
cause a malfunction.

• Hold the battery by the edges. Holding

the battery across the contact points
will seriously deplete the storage
capacity.

• Make sure that the + side faces the

bottom of the lower part.

4. Close the lid securely as illustrated with

O

C

and

O

D

.

5. Operate the buttons to check the

operation.

If you need assistance with replacement, it
is recommended that you visit a NISSAN
dealer for this service.

FCC Notice:

For USA:
This device complies with Part 15 of the
FCC Rules. Operation is subject to the fol-
lowing two conditions: (1) This device
may not cause harmful interference, and
(2) this device must accept any interfer-
ence received, including interference
that may cause undesired operation.

Note:

Changes or modifications not expressly
approved by the party responsible for
compliance could void the user’s author-
ity to operate the equipment.

For Canada:
This

device

contains

licence-exempt

transmitter(s)/receiver(s) that comply
with Innovation, Science and Economic
Development Canada’s licence-exempt
RSS(s). Operation is subject to the fol-
lowing two conditions: (1) This device
may not cause interference. (2) This de-
vice must accept any interference, in-
cluding interference that may cause un-
desired operation of the device.

LDI2637

8-28

Do-it-yourself

HEADLIGHTS

For additional information on headlight
bulb replacement, refer to the instructions
outlined in this section.

Replacing the halogen headlight
bulb (if so equipped)

The headlight is a semi-sealed beam type
which uses a replaceable headlight (halo-
gen) bulb. Because the headlight assembly
must be removed from the vehicle for bulb
replacement, it is recommended that you
visit a NISSAN dealer for this service.

CAUTION

Aiming is not necessary after replac-
ing the bulb. When aiming adjust-
ment is necessary, it is recom-
mended that you visit a NISSAN
dealer for this service.

Do not leave the headlight assembly
open without a bulb installed for a
long period of time. Dust, moisture,
smoke, etc. entering the headlight
body may affect bulb performance.
Remove the bulb from the headlight
assembly just before a replacement
bulb is installed.

Only touch the base when handling
the bulb. Never touch the glass enve-
lope. Touching the glass could sig-
nificantly affect bulb life and/or
headlight performance.

High pressure halogen gas is sealed
inside the halogen bulb. The bulb
may break if the glass envelope is
scratched or the bulb is dropped.

Use the same number and wattage
as shown in the chart.

Fog may temporarily form inside the lens
of the exterior lights in the rain or in a car
wash. A temperature difference between
the inside and the outside of the lens
causes the fog. This is not a malfunction. If
large drops of water collect inside the lens,
it is recommended that you visit a NISSAN
dealer for servicing.

Replacing the LED headlight bulb
(if so equipped)

If LED headlight bulb replacement is re-
quired, it is recommended that you visit a
NISSAN dealer for this service.

FOG LIGHTS (if so equipped)

For additional information on fog light bulb
replacement, refer to the instructions out-
lined in this section.

Replacing the LED fog light bulb

If LED fog light bulb replacement is re-
quired, it is recommended that you visit a
NISSAN dealer for this service.

LIGHTS

Do-it-yourself

8-29

EXTERIOR AND INTERIOR LIGHTS

Item

Wattage (W)

Bulb No.*

Headlight assembly (Type A) (if so equipped)*

Low (Halogen)

55

H11

High (Halogen)

60

Hb3

Turn/Park

28/8

T20

Side marker

5

W5W

Headlight assembly (Type B) (if so equipped)*

Low

High

Daytime running/Park

Turn

28/8

7444NA

Side marker

Fog light (if so equipped)

Door mirror turn signal light (if so equipped)*

Puddle light (if so equipped)*

Rear combination light (Type A) (if so equipped)*

Stop

16

PW16W

Backup (reversing)

16

921

Turn/Tail

27/7

3057K

Rear combination light (Type B) (if so equipped)*

Stop

Backup (reversing)

16

921

Turn/Tail

27/7

3057K

Cargo (tailgate) (if so equipped)

12

921

Rear combination light (Type C) (if so equipped)*

Stop

Backup (reversing)

16

W16W

Turn

21

WY21W

Tail

Side marker

Cargo (tailgate) (if so equipped)

High-mounted stop light*

Stop

Cargo (roof)

Under rail bed light (if so equipped)*

License plate light*

Map light (if so equipped)*

8

Map light (if so equipped)*

Room light*

Footwell light (if so equipped)*

Vanity mirror light (if so equipped)*

1.5

Glove box light (if so equipped)*

3.4

158

* Always check with the Parts Department at a NISSAN dealer for the latest parts information.

* It is recommended that you visit a NISSAN dealer for assistance.

8-30

Do-it-yourself

1.

Headlight assembly

2.

Map light (if so equipped)

3.

Room light

4.

Door mirror turn signal light
(if so equipped)

5.

Puddle light (if so equipped)

6.

Fog light (if so equipped)

7.

High-mount stop light

8.

Under rail bed light (if so equipped)

9.

License plate light

10.

Rear combination light

LDI3670

Do-it-yourself

8-31

Replacement procedures

All other lights are either type A, B, C or D.
When replacing a bulb, first remove the
lens, lamp and/or cover.

Indicates bulb removal

Indicates bulb installation

NOTE:

Rear combination light (Type B) (if so
equipped) bulb replacement procedure
is shown. Rear combination light (Type A)
(if so equipped) bulb replacement proce-
dure is similar.

To replace the rear combination light bulbs
perform the following procedure:

1. Remove the two fasteners

O

A

and pull

the rear combination light away from
the vehicle.

2. Remove harness connector and rotate

stop light bulb

O

B

counterclockwise to

remove. Replace bulb if necessary.

3. Rotate reverse light bulb socket

O

C

counterclockwise to remove. Replace
bulb if necessary.

4. Rotate cargo (tailgate) light bulb socket

O

D

(if so equipped) counterclockwise to

remove. Replace bulb if necessary.

5. Rotate turn/tail light bulb socket

O

E

counterclockwise to remove. Replace
bulb if necessary.

WDI0263

LDI2951

Rear combination light

LDI2952

Rear combination light

8-32

Do-it-yourself

Reverse steps to install bulbs and rear
combination light.

If you have a flat tire, see “Flat tire”
(P. 6-3).

TIRE PRESSURE

Tire Pressure Monitoring System
(TPMS)

WARNING

Radio waves could adversely af-
fect electric medical equipment.
Those who use a pacemaker
should contact the electric medi-
cal equipment manufacturer for
the possible influences before
use.

This vehicle is equipped with the Tire
Pressure Monitoring System (TPMS).
It monitors tire pressure of all four
tires except the spare. When the low
tire pressure warning light is lit and
the “Tire Pressure Low - Add Air”
warning appears in the vehicle infor-
mation display, one or more of your
tires is significantly under-inflated. If

equipped, the system also displays
pressure of all tires (except the spare
tire) on the display screen by send-
ing a signal from a sensor that is
installed in each wheel.

The TPMS will activate only when the
vehicle is driven at speeds above
16 mph (25 km/h). Also, this system
may not detect a sudden drop in tire
pressure (for example a flat tire while
driving).

For

additional

information,

see

“Warning lights, indicator lights and
audible reminders” (P. 2-12), “Tire
Pressure Monitoring System (TPMS)”
(P. 5-5), and “Flat tire” (P. 6-3).

Tire inflation pressure

Check the tire pressures (including
the spare) often and always prior to
long distance trips. The recom-
mended tire pressure specifications
are shown on the F.M.V.S.S. certifica-
tion label or the Tire and Loading

WHEELS AND TIRES

Do-it-yourself

8-33

Information label under the “Cold
Tire Pressure” heading. The Tire and
Loading Information label is affixed
to the driver side center pillar. Tire
pressures should be checked regu-
larly because:

• Most tires naturally lose air over

time.

• Tires can lose air suddenly when

driven over potholes or other ob-
jects or if the vehicle strikes a curb
while parking.

The

tire

pressures

should

be

checked when the tires are cold. The
tires are considered COLD after the
vehicle has been parked for 3 or
more hours, or driven less than 1 mile
(1.6 km) at moderate speeds.

The TPMS with Easy-Fill Tire Alert
provides visual and audible signals
outside the vehicle for inflating tires
to the recommended COLD tire

pressure. For additional information,
see “TPMS with Easy-Fill Tire Alert”
(P. 5-8).

Incorrect tire pressure, including under
inflation, may adversely affect tire life
and vehicle handling.

WARNING

Improperly inflated tires can
fail suddenly and cause an
accident.

The Gross Vehicle Weight Rat-
ing (GVWR) is located on the
F.M.V.S.S. certification label. The
vehicle weight capacity is indi-
cated on the Tire and Loading
Information label. Do not load
your vehicle beyond this capac-
ity. Overloading your vehicle
may result in reduced tire life,
unsafe

operating

conditions

due to premature tire failure, or
unfavorable handling charac-
teristics and could also lead to a
serious accident. Loading be-

yond the specified capacity
may also result in failure of
other vehicle components.

Before taking a long trip, or
whenever you heavily load your
vehicle, use a tire pressure
gauge to ensure that the tire
pressures are at the specified
level.

For additional information re-
garding tires, refer to “Impor-
tant Tire Safety Information”
(US) or “Tire Safety Information”
(Canada) in the Warranty Infor-
mation Booklet.

8-34

Do-it-yourself

Tire and Loading Information
label

1

Seating capacity: The maximum
number of occupants that can
be seated in the vehicle.

2

Vehicle load limit: For additional
information, see “Vehicle loading
information” (P. 10-20).

3

Original tire size: The size of the
tires originally installed on the
vehicle at the factory.

4

Cold tire pressure: Inflate the tires
to this pressure when the tires
are cold. Tires are considered
COLD after the vehicle has been
parked for 3 or more hours, or
driven less than 1 mile (1.6 km) at
moderate speeds. The recom-
mended cold tire inflation is set
by the manufacturer to provide
the best balance of tire wear,

vehicle handling, driveability, tire
noise, etc., up to the vehicle's
GVWR.

5

Tire size - see “Tire labeling”
(P. 8-37).

6

Spare tire size.

LDI2926

Do-it-yourself

8-35

Checking tire pressure

1. Remove the valve stem cap from

the tire.

2. Press

the

pressure

gauge

squarely onto the valve stem. Do
not press too hard or force the
valve stem sideways, or air will es-
cape. If the hissing sound of air
escaping from the tire is heard
while checking the pressure, re-
position the gauge to eliminate
this leakage.

3. Remove the gauge.

4. Read the tire pressure on the

gauge stem and compare to the
specification shown on the Tire
and Loading Information label.

5. Add air to the tire as needed. If too

much air is added, press the core
of the valve stem briefly with the
tip of the gauge stem to release
pressure. Recheck the pressure
and add or release air as needed.

6. Install the valve stem cap.

7. Check the pressure of all other

tires, including the spare.

Size

Cold Tire Inflation
Pressure

Front Original
Tire:

265/70R18

270 kPa, 39 psi

P265/70R18

250 kPa, 36 psi

P275/60R20

250 kPa, 36 psi

P275/70R18

240 kPa, 35 psi

LT245/75R17

450 kPa, 65 psi

LT275/65R18

450 kPa, 65 psi

LT265/60R20

450 kPa, 65 psi

LDI0393

8-36

Do-it-yourself

Size

Cold Tire Inflation
Pressure

Rear Original
Tire:

265/70R18

270 kPa, 39 psi

P265/70R18

250 kPa, 36 psi

P275/60R20

250 kPa, 36 psi

P275/70R18

240 kPa, 35 psi

LT245/75R17

500 kPa, 73 psi

LT275/65R18

450 kPa, 65 psi

LT265/60R20

480 kPa, 70 psi

Spare Tire
Sizes:

Cold Tire Inflation
Pressure

265/70R18

270 kPa, 39 psi

P265/70R18

250 kPa, 36 psi

P275/70R18

240 kPa, 35 psi

P275/60R20

250 kPa, 36 psi

LT245/75R17

500 kPa, 73 psi

LT275/65R18

450 kPa, 65 psi

LT265/60R20

480 kPa, 70 psi

TIRE LABELING

Federal law requires tire manufac-
turers to place standardized infor-
mation on the sidewall of all tires.
This information identifies and de-
scribes the fundamental character-
istics of the tire and also provides the
Tire Identification Number (TIN) for
safety standard certification. The TIN
can be used to identify the tire in
case of a recall.

WDI0394

Example

Do-it-yourself

8-37

O

1

Tire size (example: P215/65R15 95H)

1. P: The “P” indicates the tire is de-

signed for passenger vehicles (not
all tires have this information).

2. Three-digit number (215): This

number gives the width in milli-
meters of the tire from sidewall
edge to sidewall edge.

3. Two-digit number (65): This num-

ber, known as the aspect ratio,
gives the tire's ratio of height to
width.

4. R: The “R” stands for radial.

5. Two-digit number (15): This num-

ber is the wheel or rim diameter in
inches.

6. Two- or three-digit number (95):

This number is the tire's load
index. It is a measurement of how
much

weight

each

tire

can

support.

7. H: Tire speed rating. You should

not drive the vehicle faster than
the tire speed rating.

WDI0395

Example

8-38

Do-it-yourself

O

2

TIN (Tire Identification Number)

for a new tire (example: DOT XX XX
XXX XXXX)

1. DOT: Abbreviation for the “Depart-

ment

Of

Transportation”.

The

symbol can be placed above, be-
low or to the left or right of the Tire
Identification Number.

2. Two-digit code: Manufacturer's

identification mark.

3. Two-digit code: Tire size.

4. Three-digit code: Tire type code

(Optional).

5. Four

numbers

represent

the

week and year the tire was built.
For example, the numbers 3103
means the 31st week of 2003. If
these numbers are missing then
look on the other sidewall of the
tire.

LDI2786

Example (Type A) (if so equipped)

Do-it-yourself

8-39

 

 

 

 

 

 

 

Content      ..     30      31      32      33     ..