Content .. 11 12 13 14 ..

Nissan Titan (2022 year). Manual in english - page 13

3. Press

and

hold

the

programmed

HomeLink® button and observe the indi-
cator light.

• If

the

indicator

light

solid/

continuous, programming is complete

and your device should activate when the
HomeLink®

button

pressed

and

released.

• If the indicator light

blinks

rapidly for 2

seconds and then turns to a solid/
continuous light, continue with Steps
4-6

for a rolling code device. A second

person may make the following steps
easier. Use a ladder or other device. Do
not stand on your vehicle to perform the
next steps.

4. At the receiver located on the garage

door opener motor in the garage, locate
the “learn” or “smart” button (the name
and color of the button may vary by
manufacturer but it is usually located
near where the hanging antenna wire is
attached to the unit). If there is difficulty
locating the button, reference the ga-
rage door opener’s manual.

5. Press and release the “learn” or “smart”

button.

NOTE:
Once the button is pressed, you have ap-
proximately 30 seconds to initiate the
next step.

6. Return to the vehicle and firmly press

and hold the trained HomeLink® button
for 2 seconds and release. Repeat the
“press/hold/release” sequence up to
three times to complete the training
process. HomeLink® should now acti-
vate your rolling code equipped device.

7. If you have any questions or are having

difficulty programming your HomeLink®
buttons, refer to the HomeLink® web site
at:

www.homelink.com

call

1-800-355-3515.

PROGRAMMING HOMELINK® FOR
GATE OPENERS

If you are having difficulties training a gate
operator or garage door opener by using
the “Training” procedures, replace “Pro-
gramming HomeLink®” Step 2 with the
following:

NOTE:

When

programming

garage

door

opener, etc., unplug the device during
the “cycling” process to prevent possible
damage to the garage door opener
components.

1. For additional information, see “Pro-

gramming HomeLink®” step 1 (P. 2-91).

2-92

Instruments and controls

2. Using both hands, simultaneously press

and hold the desired HomeLink® button
and the hand-held transmitter button.
During training, your hand-held trans-
mitter may automatically stop transmit-
ting. Continue to press and hold the de-
sired HomeLink® button while you press
and re-press (“cycle”) your hand-held
transmitter every two seconds until the
frequency

signal

learned.

The

HomeLink® indicator light will flash
slowly and then rapidly after several
seconds upon successful training. DO
NOT release until the HomeLink® indica-
tor light flashes slowly and then rapidly.
When the indicator light flashes rapidly,
both buttons may be released. The rapid
flashing indicates successful training.
Proceed

with

“Programming

HomeLink®” step 3 to complete.
If the device was unplugged during the
programming procedure, remember to
plug it back in when programming is
completed.

OPERATING THE HOMELINK®
UNIVERSAL TRANSCEIVER

The HomeLink® Universal Transceiver, after
it is programmed, can be used to activate
the programmed device. To operate, sim-
ply press and release the appropriate pro-

grammed HomeLink® Universal Trans-
ceiver button. The amber indicator light will
illuminate

while

the

signal

being

transmitted.

For convenience, the hand-held transmit-
ter of the device may also be used at any
time.

PROGRAMMING TROUBLE-
DIAGNOSIS

If the HomeLink® does not quickly learn the
hand-held transmitter information:
• Replace the hand-held transmitter bat-

teries with new batteries.

• Position the hand-held transmitter with

its battery area facing away from the
HomeLink® surface.

• Press and hold both the HomeLink® and

hand-held transmitter buttons without
interruption.

• Position the hand-held transmitter 1 - 3

inches (26 - 76 mm) away from the
HomeLink® surface. Hold the transmitter
in that position for up to 15 seconds. If
HomeLink® is not programmed within
that time, try holding the transmitter in
another position – keeping the indicator
light in view at all times.

If you have any questions or are having
difficulty programming your HomeLink®
buttons, refer to the HomeLink® web site at:
www.homelink.com or call 1-800-355-3515.

CLEARING THE PROGRAMMED
INFORMATION

The following procedure clears the pro-
grammed information from both buttons.
Individual buttons cannot be cleared. How-
ever, individual buttons can be repro-
grammed. For additional information, see
“Reprogramming a single HomeLink® but-
ton” (P. 2-94).

To clear all programming:

1. Press and hold the two outer HomeLink®

buttons until the indicator light begins to
flash in approximately 10 seconds. Do
not hold for longer than 20 seconds.

2. Release both buttons.

HomeLink® is now in the programming
mode and can be programmed at any
time

beginning

with

“Programming

HomeLink®” - Step 1 (P. 2-91).

Instruments and controls

2-93

REPROGRAMMING A SINGLE
HOMELINK® BUTTON

To reprogram a HomeLink® Universal
Transceiver button, complete the following:

1. Press and hold the desired HomeLink®

button.

DO NOT

release the button.

2. The indicator light will begin to flash af-

ter 20 seconds. Without releasing the
HomeLink® button, proceed with “Pro-
gramming HomeLink®” - Step 1 (P. 2-91).

For

questions

comments,

contact

HomeLink®

at:

www.homelink.com

1–800–355–3515 (except Mexico).

The HomeLink® Universal Transceiver but-
ton has now been reprogrammed. The
new device can be activated by pressing
the HomeLink® button that was just pro-
grammed. This procedure will not affect
any

other

programmed

HomeLink®

buttons.

IF YOUR VEHICLE IS STOLEN

If your vehicle is stolen, you should change
the codes of any non-rolling code device
that

has

been

programmed

into

HomeLink®. Consult the Owner's Manual of
each device or call the manufacturer or
dealer of those devices for additional
information.

When your vehicle is recovered, you will
need to reprogram the HomeLink® Uni-
versal Transceiver with your new trans-
mitter information.

FCC Notice:

For USA:

This device complies with Part 15 of the
FCC Rules. Operation is subject to the fol-
lowing two conditions: (1) This device
may not cause harmful interference, and
(2) this device must accept any interfer-
ence received, including interference
that may cause undesired operation.

NOTE:

Changes or modifications not expressly
approved by the party responsible for
compliance could void the user’s author-
ity to operate the equipment.

For Canada:

This device contains license-exempt
transmitter(s)/receiver(s) that comply
with Innovation, Science and Economic
Development Canada’s licence-exempt
RSS(s). Operation is subject to the fol-
lowing two conditions: (1) This device
may not cause interference. (2) This de-
vice must accept any interference, in-
cluding interference that may cause un-
desired operation of the device.

2-94

Instruments and controls

3 Pre-driving checks and adjustments

Keys . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-2

NISSAN Intelligent Key® . . . . . . . . . . . . . . . . . . . . . . . 3-2
NISSAN Vehicle Immobilizer System
keys . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-4

Doors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-4

Locking with key . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-5
Locking with inside lock knob . . . . . . . . . . . . . . . . 3-6
Locking with power door lock switch . . . . . . . . . 3-6
Rear doors (King Cab® models) . . . . . . . . . . . . . . . 3-7
Automatic door locks (if so equipped) . . . . . . . . 3-8
Child safety rear door lock (if so
equipped) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-9

NISSAN Intelligent Key® system . . . . . . . . . . . . . . . . . . 3-9

Operating range . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-10
Door locks/unlocks precaution . . . . . . . . . . . . . . .3-11
NISSAN Intelligent Key® Operation . . . . . . . . . . . .3-11
How to use the remote keyless entry
function . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-15
Warning signals . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-18
Troubleshooting guide . . . . . . . . . . . . . . . . . . . . . . 3-19

Remote Engine Start (if so equipped) . . . . . . . . . . . 3-20

Remote Engine Start operating range . . . . . . . 3-20
Remote starting the vehicle . . . . . . . . . . . . . . . . . 3-21
Extending engine run time . . . . . . . . . . . . . . . . . . 3-21
Canceling a Remote Engine Start . . . . . . . . . . . 3-21

Conditions the Remote Engine Start will
not work . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-22

Hood . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-23
Fuel-filler door . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-23

Gasoline fuel engines . . . . . . . . . . . . . . . . . . . . . . . 3-24

Steering wheel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-26

Manual operation (if so equipped) . . . . . . . . . . . 3-26
Automatic operation (if so equipped) . . . . . . . . 3-27

Sun visors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-28

Vanity mirrors (if so equipped) . . . . . . . . . . . . . . . 3-28
Card holder (driver’s side only) . . . . . . . . . . . . . . . 3-29

Mirrors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-29

Manual anti-glare rearview mirror
(if so equipped) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-29
Automatic anti-glare rearview mirror
(if so equipped) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-29
Outside mirrors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-30

Truck box . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-34

Tailgate . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-34
Tie down hooks . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-38

Memory Seat (if so equipped) . . . . . . . . . . . . . . . . . . 3-38

Memory storage function . . . . . . . . . . . . . . . . . . . 3-39
Entry/exit function . . . . . . . . . . . . . . . . . . . . . . . . . . 3-40
System operation . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-40

NISSAN INTELLIGENT KEY®

Your vehicle can only be driven with the
Intelligent Keys which are registered to
your vehicle’s Intelligent Key system com-
ponents and NISSAN Vehicle Immobilizer
System components.

Never leave the keys in the vehicle.

As many as four Intelligent Keys can be
registered and used with one vehicle. The
new keys must be registered prior to the
use with the Intelligent Key system and
NISSAN Vehicle Immobilizer System of your
vehicle. It is recommended that you visit a
NISSAN dealer for this service. Since the
registration process requires erasing all

memory in the Intelligent Key components
when registering new keys, be sure to take
all Intelligent Keys that you have to the
NISSAN dealer.

A key number plate is supplied with your
keys. Record the key number and keep it in
a safe place (such as your wallet), not in the
vehicle. If you lose your keys, it is recom-
mended that you visit a NISSAN dealer for
duplicates by using the key number.
NISSAN does not record key numbers so it
is very important to keep track of your key
number plate.

A key number is only necessary when you
have lost all keys and do not have one to
duplicate from. If you still have a key, it can
be duplicated without knowing the key
number.

CAUTION

Listed below are conditions or occur-
rences which will damage the Intelli-
gent Key:

•

Do not allow the Intelligent Key,
which contains electrical compo-
nents, to come into contact with wa-
ter or salt water. This could affect the
system function.

•

Do not drop the Intelligent Key.

LPD3106

Type A (if so equipped)

1. Intelligent Key (two sets)

2. Mechanical key

3. Master key

4. Key number plate (one plate)

LPD3605

Type B (if so equipped)

KEYS

3-2

Pre-driving checks and adjustments

•

Do not strike the Intelligent Key
sharply against another object.

•

Do not change or modify the Intelli-
gent Key.

•

Wetting may damage the Intelligent
Key. If the Intelligent Key gets wet,
immediately wipe until it is com-
pletely dry.

•

Do not place the Intelligent Key for an
extended period in an area where
temperatures exceed 140°F (60°C).

•

Do not attach the Intelligent Key with
a key holder that contains a magnet.

•

Do not place the Intelligent Key near
equipment that produces a magnetic
field, such as a TV, audio equipment
and personal computers.

If an Intelligent Key is lost or stolen, NISSAN
recommends erasing the ID code of that
Intelligent Key from the vehicle. This may
prevent the unauthorized use of the Intelli-
gent Key to operate the vehicle. For infor-
mation regarding the erasing procedure, it
is recommended that you visit a NISSAN
dealer.

Mechanical key

The Intelligent Key contains the mechani-
cal key.

To remove the mechanical key, release the
lock knob on the back of the Intelligent Key.

To install the mechanical key, firmly insert it
into the Intelligent Key until the lock knob
returns to the lock position.

Use the mechanical key to lock or unlock
the driver's door, tailgate and glove box.

CAUTION

Always carry the mechanical key in-
stalled in the Intelligent Key slot.

For additional information, see “Doors”
(P. 3-4), “Tailgate” (P. 3-34) or “Storage”
(P. 2-70).

Valet hand-off

When you have to leave a key with a valet,
give them the Intelligent Key itself, keep the
mechanical key and master key with you to
protect your belongings.

To prevent the glove box from being
opened during valet hand-off, follow the
procedures below:

1. Remove the mechanical key from the

Intelligent Key.

2. Lock the glove box and tailgate with the

mechanical key or master key.

3. Hand the Intelligent Key without the me-

chanical key to the valet, keep the me-
chanical and master key with you.

For additional information, see “Storage”
(P. 2-70) and “Tailgate” (P. 3-34).

SPA1951

Pre-driving checks and adjustments

3-3

NISSAN VEHICLE IMMOBILIZER
SYSTEM KEYS

Additional or replacement keys:

If you still have a key, the key number is not
necessary when you need extra NISSAN
Vehicle Immobilizer System keys. Your ex-
isting key can be duplicated without know-
ing the key number. As many as four
NISSAN Vehicle Immobilizer System keys
can be used with one vehicle. You should
bring all NISSAN Vehicle Immobilizer Sys-
tem keys that you have to the NISSAN
dealer for registration. This is because the
registration process will erase the memory
of all key codes previously registered into
the NISSAN Vehicle Immobilizer System. Af-
ter the registration process, these compo-
nents will only recognize keys coded into
the NISSAN Vehicle Immobilizer System
during registration. Any virtual key acces-
sories (if so equipped) will also have to be
reregistered. Any key that is not given to the
dealer at the time of registration will no
longer be able to start your vehicle.

CAUTION

Do not allow the immobilizer system
key, which contains an electrical tran-
sponder, to come into contact with wa-
ter or salt water. This could affect sys-
tem function.

When the doors are locked using one of the
following methods, the doors cannot be
opened using the inside or outside door
handles. The doors must be unlocked to
open the doors.

WARNING

•

Always have the doors locked while
driving. Along with the use of seat
belts, this provides greater safety in
the event of an accident by helping to
prevent persons from being thrown
from the vehicle. This also helps keep
children and others from uninten-
tionally opening the doors, and will
help keep out intruders.

•

Before opening any door, always look
for and avoid oncoming traffic.

DOORS

3-4

Pre-driving checks and adjustments

•

To help avoid risk of injury or death
through unintended operation of the
vehicle and/or its systems, including
entrapment in windows or inadver-
tent door lock activation, do not
leave children, people who require
the assistance of others or pets unat-
tended in your vehicle. Additionally,
the temperature inside a closed ve-
hicle on a warm day can quickly be-
come high enough to cause a signifi-
cant risk of injury or death to people
and pets.

LOCKING WITH KEY

To lock the door using the mechanical key,
turn the key toward the front of the vehicle

. This will only lock the door and will not

activate the security system. To arm the
security system, press the

button

on the Intelligent Key.

To unlock the door using the mechanical
key, turn the key toward the rear of the
vehicle

. This will only unlock the corre-

sponding door and will not disarm the se-
curity system.

For additional information, see “Security
systems” (P. 2-39).

WPD0311

Driver’s side

Pre-driving checks and adjustments

3-5

LOCKING WITH INSIDE LOCK KNOB

To lock the door without the key, move the
inside lock to the lock position

, then

close the door.

To unlock the door without the key, move
the inside lock knob to the unlock position

LOCKING WITH POWER DOOR
LOCK SWITCH

To lock all the doors and the tailgate lock (if
so equipped) without a key, push the door
lock switch (driver's or front passenger's
side) to the lock position

. When locking

the door this way, be certain not to leave
the key inside the vehicle.

To unlock all the doors and the tailgate lock
(if so equipped) without a key, push the
door lock switch (driver's or front passen-
ger's side) to the unlock position

Lockout protection

With the Intelligent Key left in the vehicle, if
all doors are locked, then closed, a chime
will sound after the last door is closed and
all doors will unlock automatically.

These functions help to prevent the Intelli-
gent Key from being accidentally locked
inside the vehicle.

LPD2092

Inside lock

WPD0381

3-6

Pre-driving checks and adjustments

REAR DOORS (King Cab® models)

1. Open the driver’s or passenger’s door.

2. From the outside, pull the door handle

toward you.

3. Open the door to the desired position.

LPD0278

LPD2591

LPD2592

Pre-driving checks and adjustments

3-7

CAUTION

Be careful when opening and exiting
the driver’s side rear door if the fuel-
filler door is open. This may cause dam-
age to the driver’s side rear door or
fuel-filler door if you open fully and
they make contact.

AUTOMATIC DOOR LOCKS (if so
equipped)

• All doors lock automatically when the ve-

hicle speed reaches 15 mph (24 km/h).

• All doors unlock automatically when the

transmission is placed in the P (Park) po-
sition or when the ignition switch is
placed in the OFF position, depending on
the option selected in the “Vehicle Set-
tings” menu.

NOTE:
The Auto Unlock (if so equipped) feature
can be changed using the “Vehicle Set-
tings” menu on the vehicle information
display. For additional information, see
“Vehicle information display” (P. 2-23).

LPD2593

LPD2594

3-8

Pre-driving checks and adjustments

CHILD SAFETY REAR DOOR LOCK
(if so equipped)

Child safety locks help prevent the rear
doors from being opened accidentally, espe-
cially when small children are in the vehicle.
The child safety lock levers are located on
the edge of the rear doors.

When the lever is in the unlock position

the door can be opened from the outside
or the inside.

When the lever is in the LOCK position

the door can be opened only from the
outside.

WARNING

•

Radio waves could adversely affect
electric medical equipment. Those
who use a pacemaker should contact
the

electric

medical

equipment

manufacturer for the possible influ-
ences before use.

•

The Intelligent Key transmits radio
waves when the buttons are pressed.
The FAA advises the radio waves may
affect aircraft navigation and com-
munication systems. Do not operate
the Intelligent Key while on an air-
plane. Make sure the buttons are not
operated unintentionally when the
unit is stored for a flight.

•

Never leave the Intelligent Key in the
vehicle when you leave the vehicle.

The Intelligent Key system can operate all
the door locks using the remote control
function or pushing the request switch (if
so equipped) on the vehicle without taking
the key out from a pocket or purse. The
operating environment and/or conditions
may affect the Intelligent Key system
operation.

Be sure to read the following before using
the Intelligent Key system.

CAUTION

Be sure to carry the Intelligent Key with
you when operating the vehicle.

The Intelligent Key is capable of receiving
and transmitting radio waves. The Intelli-
gent Key system transmits weak radio
waves from various distances. Environ-
mental conditions may interfere with the
operation of the Intelligent Key system un-
der the following operating conditions:
• When operating near a location where

strong radio waves are transmitted, such
as a TV tower, power station and broad-
casting station.

• When in possession of wireless equip-

ment, such as a cellular telephone, trans-
ceiver, or a CB radio.

• When the Intelligent Key is in contact with

or covered by metallic materials.

• When any type of radio wave remote con-

trol is used nearby.

• When the Intelligent Key is placed near an

electric appliance such as a personal
computer.

• When the vehicle is parked near a parking

meter.

LPD3096

NISSAN INTELLIGENT KEY® SYSTEM

Pre-driving checks and adjustments

3-9

In such cases, correct the operating condi-
tions before using the Intelligent Key func-
tion or use the mechanical key.

Although the life of the battery varies de-
pending on the operating conditions, the
battery’s life is approximately two years. If
the battery is discharged, replace it with a
new one.

When the Intelligent Key battery is low the
“Key ID Incorrect” warning appears in the
vehicle information display. When the Intel-
ligent Key battery is low the “Key Battery
Low” indicator appears. For additional in-
formation, see “Vehicle information display
warnings and indicators” (P. 2-32).

Since the Intelligent Key is capable of re-
ceiving radio waves, if the key is left near
equipment which transmits strong radio
waves, such as signals from a TV and per-
sonal computer, the battery life may be-
come shorter.

For additional information, see “Battery re-
placement” (P. 8-27).

As many as four Intelligent Keys can be
registered and used with one vehicle. For
information about the purchase and use of
additional Intelligent Keys, it is recom-
mended that you visit a NISSAN dealer.

OPERATING RANGE

The Intelligent Key functions can only be
used when the Intelligent Key is within the
specified operating range from the request
switch

(if so equipped).

When the Intelligent Key battery is dis-
charged or strong radio waves are present
near the operating location, the Intelligent
Key operating range becomes narrower,
and the Intelligent Key may not function
properly.

The operating range is within 31.50 in (80
cm) from each request switch

(if so

equipped).

If the Intelligent Key is too close to the door
glass or handle, the request switches (if so
equipped) may not function.

When the Intelligent Key is within the oper-
ating range, it is possible for anyone, even
someone who does not carry the Intelli-
gent Key, to push the request switch (if so
equipped) to lock/unlock the doors.

LPD2338

3-10

Pre-driving checks and adjustments

DOOR LOCKS/UNLOCKS
PRECAUTION

• Do not push the door handle request

switch (if so equipped) with the Intelligent
Key held in your hand as illustrated. The
close distance to the door handle will
cause the Intelligent Key system to have
difficulty recognizing that the Intelligent
Key is outside the vehicle.

• After locking with the door handle re-

quest switch (if so equipped), verify the
doors are securely locked by testing
them.

• To prevent the Intelligent Key from being

left inside the vehicle, make sure you
carry the Intelligent Key with you and then
lock the doors.

• Do not pull the door handle before push-

ing the door handle request switch (if so
equipped). The door will be unlocked but
will not open. Release the door handle
once and pull it again to open the door.

NISSAN INTELLIGENT KEY®
OPERATION

You can lock or unlock the doors without
taking the Intelligent Key out of your pocket
or bag.

When you carry the Intelligent Key with you,
you can lock or unlock all doors by pushing
the door handle request switch (if so
equipped) within the range of operation.

LPD2554

LPD3097

Pre-driving checks and adjustments

3-11

Locking doors

1. Move the shift lever to the P (Park) posi-

tion, place the ignition switch in the LOCK
position and make sure you carry the
Intelligent Key with you.

2. Close the driver’s door and push the

driver’s door request switch (if so
equipped)

OR close all doors and

push any door request switch (if so
equipped) while carrying the Intelligent
Key with you.

3. Push the door handle request switch (if

so equipped) while carrying the Intelli-
gent Key with you.

4. All doors and the tailgate lock (if so

equipped) will lock.

5. The hazard indicator lights flash twice,

the outside chirp sounds twice, and the
front and tail lights may turn on for 10
seconds.

NOTE:
• Request switches (if so equipped) for

all doors can be deactivated when the
“I-Key Door Lock (if so equipped)” set-
ting is switched to OFF in the Vehicle
Settings of the vehicle information dis-
play. For additional information, see
“Vehicle information display” (P. 2-23).

• Doors and the tailgate lock (if so

equipped) will lock with the door
handle request switch (if so equipped)
while the ignition switch is not in the
LOCK position.

• Doors do not lock by pushing the door

handle request switch (if so equipped)
while the driver’s door is open. How-
ever, doors lock with the mechanical
key even if any door is open.

LPD3098

LPD3099

3-12

Pre-driving checks and adjustments

• Doors and the tailgate lock (if so

equipped) do not lock with the door
handle request switch (if so equipped)
if the Intelligent Key is inside the ve-
hicle. A beep will sound to warn you.
However, when an Intelligent Key is in-
side the vehicle, doors can be locked
with another Intelligent Key.

WARNING

After locking the doors using the re-
quest switch (if so equipped), make
sure that the doors have been securely
locked by operating the door handles.
Failure to follow these instructions may
result in inadvertently unlocking the
doors, which may decrease the safety
and security of your vehicle.

CAUTION

•

When locking the doors using the re-
quest switch (if so equipped), make
sure to have the Intelligent Key in
your possession before operating
the request switch (if so equipped) to
prevent the Intelligent Key from be-
ing left in the vehicle.

•

The request switch (if so equipped) is
operational only when the Intelligent
Key has been detected by the Intelli-
gent Key system.

Lockout protection

To prevent the Intelligent Key from being
accidentally locked in the vehicle, lockout
protection is equipped with the Intelligent
Key system.

When any door is open, the doors are
locked, and then the Intelligent Key is put
inside the vehicle and all the doors are
closed; a chime will sound and the lock will
automatically unlock.

NOTE:

The doors may not lock when the Intelli-
gent Key is in the same hand that is op-
erating

the

request

switch

(if

equipped) to lock the door. Put the Intel-
ligent Key in a purse, pocket or your
other hand.

CAUTION

The lockout protection may not func-
tion under the following conditions:

•

When the Intelligent Key is placed on
top of the instrument panel.

•

When the Intelligent Key is placed in-
side the glove box or a storage bin.

•

When the Intelligent Key is placed in-
side the door pockets.

•

When the Intelligent Key is placed in-
side or near metallic materials.

Pre-driving checks and adjustments

3-13

Content .. 11 12 13 14 ..