Nissan Murano Z51 (2013 year). Manual - part 96

 

  Index      Manuals     Nissan Murano Z51 (2013 year) - Service and Repair Manual

 

Search            copyright infringement  

 

 

 

 

 

 

 

 

Content      ..     94      95      96      97     ..

 

 

Nissan Murano Z51 (2013 year). Manual - part 96

 

 

C1708, C1709, C1710, C1711 TIRE PRESSURE SENSOR

WT-23

< DTC/CIRCUIT DIAGNOSIS >

C

D

F

G

H

I

J

K

L

M

A

B

WT

N

O

P

4.

Check the continuity between BCM harness connector and ground.

Is the inspection result normal?

YES

>> GO TO 3.

NO

>> Repair or replace damaged parts.

3.

CHECK TIRE PRESSURE RECEIVER POWER SUPPLY CIRCUIT 

1.

Connect the BCM harness connector.

2.

Turn the ignition switch ON.

CAUTION:

Never start the engine.

3.

Check the voltage between the BCM harness connector and ground.

Is the inspection result normal?

YES

>> GO TO 4.

NO

>> Repair or replace damaged parts.

4.

CHECK TIRE PRESSURE RECEIVER

Check tire pressure receiver. Refer to 

WT-29, "Diagnosis Procedure"

.

Is the inspection result normal?

YES

>> GO TO 5.

NO

>> Replace tire pressure receiver. Refer to 

WT-48, "Removal and Installation"

.

5.

CHECK ID REGISTRATION

Perform ID registration of all tire pressure sensors. Refer to 

WT-18, "Work Procedure"

.

Can ID registration of all tire pressure sensors be completed?

YES

>> GO TO 6.

NO

>> Replace tire pressure sensor. Refer to 

WT-45, "Exploded View"

.

6.

CHECK TIRE PRESSURE MONITORING SYSTEM

With CONSULT

1.

Drive at a speed of 40 km/h (25 MPH) or more for several minutes without stopping.

2.

Perform “DATA MONITOR” in “AIR PRESSURE MONITOR” of “BCM”.

3.

Select “BCM” in “DATA MONITOR”, and check that the tire pressures match the standard value.

BCM

Tire pressure receiver

Continuity

Connector

Terminal

Connector

Terminal

M123

137

M21

1

Existed

138

4

139

2

BCM

Continuity

Connector

Terminal

M123

137

Ground

Not existed

138

139

BCM

Voltage

(Approx.)

Connector

Terminal

M123

138

Ground

5 V

Revision: 2012 September

2013 MURANO

WT-24

< DTC/CIRCUIT DIAGNOSIS >

C1708, C1709, C1710, C1711 TIRE PRESSURE SENSOR

CAUTION:

Stop the vehicle and within 15 minutes, use “DATA MONITOR” in “AIR PRESSURE MONITOR” of
“BCM”   to read the tire pressure for all wheels.
Is the inspection result normal?

YES

>> Replace the DTC-detected malfunctioning tire pressure sensor. Refer to 

WT-45, "Exploded View"

.

NO

>> Replace BCM. Refer to 

BCS-84, "Exploded View"

.

Monitor item

Condition

Displayed value

AIR PRESS FL

Drive at a speed of 40 km/h (25 MPH) or more, for several 
minutes without stopping.

Internal pressure of tires

AIR PRESS FR

AIR PRESS RR

AIR PRESS RL

Revision: 2012 September

2013 MURANO

C1716, C1717, C1718, C1719 TIRE PRESSURE SENSOR

WT-25

< DTC/CIRCUIT DIAGNOSIS >

C

D

F

G

H

I

J

K

L

M

A

B

WT

N

O

P

C1716, C1717, C1718, C1719 TIRE PRESSURE SENSOR

DTC Logic

INFOID:0000000008454507

DTC DETECTION LOGIC

DTC CONFIRMATION PROCEDURE

1.

DTC REPRODUCTION PROCEDURE

With CONSULT

1.

Turn the ignition switch ON.

CAUTION:

Never start the engine.

2.

Check the tire pressure for all wheels and adjust to the specified value. Refer to 

WT-49, "Tire Air Pres-

sure"

3.

Perform “SELF-DIAG RESULTS” in “AIR PRESSURE MONITOR” of “BCM”.

Is DTC “C1716”, “C1717”, “C1718”, “C1719” detected?

YES

>> Perform trouble diagnosis. Refer to 

WT-25, "Diagnosis Procedure"

.

NO

>> INSPECTION END

Diagnosis Procedure

INFOID:0000000008454508

1.

CHECK TIRE PRESSURE

Check the internal pressure of all wheels. Refer to 

WT-49, "Tire Air Pressure"

Is the inspection result normal?

YES

>> Replace the DTC-detected malfunctioning tire pressure sensor. Refer to 

WT-45, "Exploded View"

.

NO

>> After adjusting the tire pressure, GO TO 2.

2.

CHECK TIRE PRESSURE SIGNAL

With CONSULT

1.

Check and adjust the tire pressure for all wheels. Refer to 

WT-49, "Tire Air Pressure"

2.

Perform tire pressure sensor ID registration for all wheels. Refer to 

WT-18, "Work Procedure"

3.

Drive for 3 minutes at a speed of 40 km/h (25 MPH) or more, then drive normally for 10 minutes.

4.

Perform “DATA MONITOR” in “AIR PRESSURE MONITOR” of “BCM”.

5.

Select “BCM” in “DATA MONITOR”, and check that the tire pressures match the standard value.

CAUTION:

Stop the vehicle and within 15 minutes, use CONSULT “DATA MONITOR” to display the tire pres-
sure for all wheels.

6.

Check that “DATA MONITOR” displays tire pressure of 438.60 kPa (4.47 kg/cm

2

, 63.60 Psi).

Is the inspection 438.60 kPa (4.47 kg/cm

2

, 63.60 Psi)?

YES

>> Replace tire pressure sensor the tire pressure 438.60 kPa (4.386 bar, 4.47 kg/cm

2

, 63.60 Psi) dis-

played. Refer to 

WT-45, "Exploded View"

.

NO

>> GO TO 1.

DTC

Display item

Malfunction detected condition

Possible case

C1716

[PRESSDATA ERR] FL

Malfunction in the tire pressure data from the front left 
wheel tire pressure sensor.

• ID registration is not fin-

ished

• Tire pressure sensor mal-

function

C1717

[PRESSDATA ERR] FR

Malfunction in the tire pressure data from the front right 
wheel tire pressure sensor.

C1718

[PRESSDATA ERR] RR

Malfunction in the tire pressure data from the rear right 
wheel tire pressure sensor.

C1719

[PRESSDATA ERR] RL

Malfunction in the tire pressure data from the rear left wheel 
tire pressure sensor.

Revision: 2012 September

2013 MURANO

WT-26

< DTC/CIRCUIT DIAGNOSIS >

C1729 VEHICLE SPEED SIGNAL

C1729 VEHICLE SPEED SIGNAL

Description

INFOID:0000000008454509

BCM detects no vehicle speed signal.

DTC Logic

INFOID:0000000008454510

DTC DETECTION LOGIC

DTC CONFIRMATION PROCEDURE

1.

DTC REPRODUCTION PROCEDURE

With CONSULT

1.

Drive for several minutes at a speed of 40 km/h (25 MPH) or more, then stop the vehicle.

2.

Perform “SELF-DIAG RESULTS” in “AIR PRESSURE MONITOR” of “BCM”.

Is DTC “C1729” detected?

YES

>> Perform trouble diagnosis. Refer to 

WT-26, "Diagnosis Procedure"

.

NO

>> INSPECTION END

Diagnosis Procedure

INFOID:0000000008454511

1.

PERFORM COMBINATION METER SELF-DIAGNOSIS

With CONSULT

Perform “SELF-DIAG RESULTS” of “METER/M&A”.
Is any DTC detected?

YES

>> Check the DTC. Refer to 

MWI-67, "DTC Index"

.

NO

>> GO TO 2.

2.

PERFORM SELF-DIAGNOSIS

With CONSULT

Perform “SELF-DIAG RESULTS” in “AIR PRESSURE MONITOR” of “BCM”.

Is DTC “C1729” detected?

YES

>> Replace BCM. Refer to 

WT-8, "COMMON ITEM : CONSULT Function (BCM - COMMON ITEM)"

.

NO

>> GO TO 3.

3.

CHECK INFORMATION

With CONSULT

1.

Perform “DATA MONITOR” in “AIR PRESSURE MONITOR” of “BCM”.

2.

Select “BCM” in “DATA MONITOR”, and check the input/output values. Refer to 

BCS-48, "Reference

Value"

Is the inspection result normal?

YES

>> Check pin terminal and connection of each harness connector for malfunctioning conditions. 

NO

>> Replace BCM. Refer to 

BCS-84, "Exploded View"

DTC

Display item

Malfunction detected condition

Possible case

C1729

VHCL SPEED SIG ERR

Vehicle speed signal not detected.

• CAN communication error
• Combination meter malfunction

Revision: 2012 September

2013 MURANO

C1734 BCM

WT-27

< DTC/CIRCUIT DIAGNOSIS >

C

D

F

G

H

I

J

K

L

M

A

B

WT

N

O

P

C1734 BCM

DTC Logic

INFOID:0000000008454512

DTC DETECTION LOGIC

DTC CONFIRMATION PROCEDURE

1.

DTC REPRODUCTION PROCEDURE

With CONSULT

1.

Drive at a speed of 40 km/h (25 MPH) or more for several minutes without stopping.

2.

Perform “SELF-DIAG RESULTS” in “AIR PRESSURE MONITOR” of “BCM”.

CAUTION:

Perform within 15 minutes after stop the vehicle.

Is DTC “C1734” detected?

YES

>> Perform trouble diagnosis. Refer to 

WT-27, "Diagnosis Procedure"

.

NO

>> INSPECTION END

Diagnosis Procedure

INFOID:0000000008454513

1.

CHECK BCM POWER SUPPLY

1.

Turn the ignition switch OFF.

2.

Disconnect BCM harness connector.

3.

Check voltage between BCM harness connector terminals and ground.

Is the power supply normal?

YES

>> GO TO 2.

NO

>>

Check the following. If any items are damaged, repair or replace damage parts.

• 40A fusible link [No. L located in the fuse block]. Refer to 

PG-113, "Fuse and Fusible Link

Arrangement"

.

• 10A fuse [No. 10 located in the fuse block (J/B)]. Refer to 

PG-112, "Fuse, Connector and Termi-

nal Arrangement"

.

• Harness for short or open between battery and BCM harness connector M118 terminal 1.
• Harness for short or open between battery and BCM harness connector M119 terminal 11.
• Check the Battery voltage.

2.

CHECK BCM GROUND

Check the continuity between BCM harness connector and ground.

Is the inspection result normal?

YES

>> GO TO 3.

NO

>> Repair or replace damaged parts.

3.

CHECK HARNESS BETWEEN BCM AND TIRE PRESSURE RECEIVER 

1.

Disconnect tire pressure receiver harness connector.

2.

Check the continuity between BCM harness connector and tire pressure receiver harness connector.

DTC 

Display item

Malfunction detected condition

Possible case

C1734

CONTROL UNIT

Tire pressure monitoring system malfunction in BCM

BCM malfunction

BCM

Voltage

(Approx.)

Connector

Terminal

M118

1

Ground

Battery voltage

M119

11

BCM

Continuity

Connector

Terminal

M119

13

Ground

Existed

Revision: 2012 September

2013 MURANO

WT-28

< DTC/CIRCUIT DIAGNOSIS >

C1734 BCM

3.

Check the continuity between BCM harness connector and ground.

Is the inspection result normal?

YES

>> GO TO 4.

NO

>> Repair or replace damaged parts.

4.

CHECK BCM 

Check the BCM input/output signal. Refer to 

BCS-48, "Reference Value"

.

Is the inspection result normal?

YES

>> INSPECTION END

NO

>> GO TO 5.

5.

CHECK BCM HARNESS CONNECTOR

Check the BCM pin terminals for damage or loose connection with harness connector.

Is the inspection result normal?

YES

>> Replace BCM. Refer to 

BCS-84, "Exploded View"

.

NO

>> Check for looseness or damage at the harness connector pins of the low tire pressure warning

control unit. Repair or replace if necessary.

BCM

Tire pressure receiver

Continuity

Connector

Terminal

Connector

Terminal

M123

137

M21

1

Existed

138

4

139

2

BCM

Continuity

Connector

Terminal

M123

137

Ground

Not existed

138

139

Revision: 2012 September

2013 MURANO

TIRE PRESSURE RECEIVER

WT-29

< DTC/CIRCUIT DIAGNOSIS >

C

D

F

G

H

I

J

K

L

M

A

B

WT

N

O

P

TIRE PRESSURE RECEIVER

Component Function Check

INFOID:0000000008454514

1.

TIRE PRESSURE MONITORING SYSTEM OPERATION

With CONSULT

1.

Drive for 3 minutes at a speed of 40 km/h (25 MPH) or more, then drive normally for 10 minutes.

2.

On “DATA MONITOR”, select “AIR PRESS FL”, “AIR PRESS FR”, “AIR PRESS RR” and “AIR PRESS
RL”, and check that the tire pressures match the standard value.

CAUTION:

Stop the vehicle and within 5 minutes, use CONSULT “DATA MONITOR” to display the tire pressure for
all wheels.

Is the inspection result normal?

YES

>> INSPECTION END

NO

>> Perform trouble diagnosis. Refer to 

WT-29, "Diagnosis Procedure"

.

Diagnosis Procedure

INFOID:0000000008454515

1.

CHECK TIRE PRESSURE RECEIVER SIGNAL

1.

Turn the ignition switch ON.

CAUTION:

Never start the engine.

2.

Check tire pressure receiver connector and ground signal with oscilloscope.

Is the inspection result normal?

YES

>> INSPECTION END

NO

>> GO TO 2.

2.

CHECK TIRE PRESSURE RECEIVER INPUT VOLTAGE

1.

Turn the ignition switch OFF.

2.

Disconnect tire pressure receiver connector.

3.

Turn the ignition switch ON.

Monitor item

Condition

Displayed value

AIR PRESS FL

Drive for 3 minutes at a speed of 40 km/h (25 MPH) or 
more, then drive normally for 10 minutes.

Internal pressure of tires

AIR PRESS FR

AIR PRESS RR

AIR PRESS RL

Tire pressure receiver

Condition

Voltage

(Approx.)

Connector

Terminal

M21

2

Ground

Stand by state

When receiving the signal from the tire 
pressure sensor

OCC3881D

OCC3880D

Revision: 2012 September

2013 MURANO

WT-30

< DTC/CIRCUIT DIAGNOSIS >

TIRE PRESSURE RECEIVER

CAUTION:

Never start the engine.

4.

Check voltage between tire pressure receiver connector and ground.

Is the inspection result normal?

YES

>> GO TO 3.

NO

>> Repair or replace damaged parts. 

3.

CHECK TIRE PRESSURE RECEIVER GROUND CIRCUIT

1.

Turn the ignition switch OFF.

2.

Disconnect BCM harness connector.

3.

Check continuity between BCM harness connector and tire pressure receiver connector.

4.

Check continuity between BCM harness connector and ground.

Is the inspection result normal?

YES

>> GO TO 4.

NO

>> Repair or replace damaged parts. 

4.

CHECK BCM CIRCUIT

Inspect the BCM circuit. Refer to 

WT-27, "Diagnosis Procedure"

.

Is the BCM circuit normal?

YES

>> Replace tire pressure receiver. Refer to 

WT-48, "Removal and Installation"

.

NO

>> Replace BCM. Refer to 

BCS-84, "Exploded View"

.

Tire pressure receiver

Voltage

(Approx.)

Connector

Terminal

M21

4

Ground

5.0 V

BCM

Tire pressure receiver

Continuity

Connector

Terminal

Connector

Terminal

M123

137

M21

1

Existed

BCM

Continuity

Connector

Terminal

M123

137

Ground

Not existed

Revision: 2012 September

2013 MURANO

LOW TIRE PRESSURE WARNING LAMP

WT-31

< DTC/CIRCUIT DIAGNOSIS >

C

D

F

G

H

I

J

K

L

M

A

B

WT

N

O

P

LOW TIRE PRESSURE WARNING LAMP

Component Function Check

INFOID:0000000008454516

1.

CHECK THE ILLUMINATION OF THE LOW TIRE PRESSURE WARNING LAMP

Check that the low tire pressure warning lamp is turned OFF after illuminating for approximately 1 second,
when the ignition switch is turned ON.

Is the inspection result normal?

YES

>> INSPECTION END

NO

>> Perform trouble diagnosis. Refer to 

WT-31, "Diagnosis Procedure"

Diagnosis Procedure

INFOID:0000000008454517

1.

POWER SUPPLY AND GROUND CIRCUIT

Check power supply and ground circuit. Refer to 

WT-32, "Diagnosis Procedure"

Is the inspection result normal?

YES

>> GO TO 2.

NO

>> Repair or replace damaged parts.

2.

PERFORM SELF-DIAGNOSIS

With CONSULT

Perform “SELF-DIAG RESULTS” in “AIR PRESSURE MONITOR” of “BCM”.
Is any DTC detected?

YES

>> Check the DTC. Refer to 

MWI-67, "DTC Index"

NO

>> GO TO 3.

3.

CHECK LOW TIRE PRESSURE WARNING LAMP SIGNAL

With CONSULT

1.

Turn the ignition switch ON.

CAUTION:

Never start the engine.

2.

Perform “DATA MONITOR” in “AIR PRESSURE MONITOR” of “BCM”.

3.

Select “BCM” in “DATA MONITOR”, and check that the low tire pressure warning lamp is turned OFF after
illuminating for approximately 1 second, when the ignition switch is turned ON.

Is the inspection result normal?

YES

>> Check the combination meter. Refer to 

MWI-6, "METER SYSTEM : System Description"

.

NO

>> Replace the BCM. Refer to 

BCS-84, "Exploded View"

Revision: 2012 September

2013 MURANO

WT-32

< DTC/CIRCUIT DIAGNOSIS >

POWER SUPPLY AND GROUND CIRCUIT

POWER SUPPLY AND GROUND CIRCUIT

Diagnosis Procedure

INFOID:0000000008454518

1.

POWER SUPPLY SYSTEM CHECK

1.

Turn the ignition switch OFF.

2.

Disconnect the BCM harness connector.

3.

Turn the ignition switch ON.

CAUTION:

Never start the engine.

4.

Check the voltage between the BCM harness connector and the ground.

Is the inspection result normal?

YES

>> GO TO 2.

NO

>> Repair or replace damaged parts.

2.

GROUND SYSTEM INSPECTION

1.

Turn the ignition switch OFF.

2.

Check the continuity between the BCM harness connector and the ground.

Is the inspection result normal?

YES

>> • Check the 10A fuse [No. 10 in fuse block (J/B)].

• Check the 40A fusible link [No. L in fuse block].

NO

>> Repair or replace damaged parts.

BCM

Voltage

Connector

Terminal

M118

1

Ground

Battery voltage

M119

11

BCM

Continuity

Connector

Terminal

M119

13

Ground

Existed

Revision: 2012 September

2013 MURANO

TPMS

WT-33

< SYMPTOM DIAGNOSIS >

C

D

F

G

H

I

J

K

L

M

A

B

WT

N

O

P

SYMPTOM DIAGNOSIS

TPMS

Symptom Table 

INFOID:0000000008454519

LOW TIRE PRESSURE WARNING LAMP SYMPTOM CHART

Revision: 2012 September

2013 MURANO

WT-34

< SYMPTOM DIAGNOSIS >

TPMS

Diagnosis items

Symptom

(Ignition switch 

ON)

Low tire pressure warning lamp

Cause

Action

Low tire pres-
sure warning 
lamp

The low tire pres-
sure warning lamp 
illuminates for 1 
second, then turns 
OFF.

Wake-up operation for all 
tire pressure sensors at 
wheels is completed.

No system malfunctions

The low tire pres-
sure warning lamp 
repeats blinking 
ON for 2 seconds 
and OFF for 0.2 
seconds.

Wake-up operation for all 
tire pressure sensors at 
wheels is not completed.

Perform the wake-up oper-
ation for all tire pressure 
sensors at wheels. Refer to 

WT-17, "Work Procedure"

.

The low tire pres-
sure warning lamp 
blinks once.

The front left tire pres-
sure sensor is not acti-
vated.

Perform the wake-up oper-
ation for the tire pressure 
sensor at front left wheel. 
Refer to 

WT-17, "Work Pro-

cedure"

.

The low tire pres-
sure warning lamp 
repeats blinking 
twice.

The front right tire pres-
sure sensor is not acti-
vated.

Perform the wake-up oper-
ation for the tire pressure 
sensor at front right wheel. 
Refer to 

WT-17, "Work Pro-

cedure"

.

The low tire pres-
sure warning lamp 
repeats blinking for 
3 times.

The rear right tire pres-
sure sensor is not acti-
vated.

Perform the wake-up oper-
ation for the tire pressure 
sensor at rear right wheel. 
Refer to 

WT-17, "Work Pro-

cedure"

.

The low tire pres-
sure warning lamp 
repeats blinking for 
4 times.

The rear left tire pressure 
sensor is not activated.

Perform the wake-up oper-
ation for the tire pressure 
sensor at rear left wheel. 
Refer to 

WT-17, "Work Pro-

cedure"

.

The low tire pres-
sure warning lamp 
turns ON and stays 
illuminated.

Low tire pressure

Check the tire pressure for 
all wheels and adjust to the 
specified value. Refer to 

WT-49, "Tire Air Pressure"

SEIA0592E

SEIA0593E

JPEIC0090GB

SEIA0595E

SEIA0596E

SEIA0597E

SEIA0598E

Revision: 2012 September

2013 MURANO

TPMS

WT-35

< SYMPTOM DIAGNOSIS >

C

D

F

G

H

I

J

K

L

M

A

B

WT

N

O

P

NOTE:
If tire pressure sensor wake-up operation is not completed for two or more tire pressure sensors, the applica-
ble low tire pressure warning lamp blinking patterns are displayed continuously.
(Example: Blinks once/OFF/blinks 3 times = Wake-up operation is not completed at the front left wheel and
rear right wheel tire pressure sensors.)

Low tire pres-
sure warning 
lamp

The low tire pres-
sure warning lamp 
repeats blinking at 
0.5-second inter-
vals for 1 minute, 
and then stays illu-
minated.

The combination meter 
fuse is open or removed 
(or pulled out).

Check and install the com-
bination meter fuse. If nec-
essary, replace the fuse.

The low tire pressure 
warning control unit har-
ness connector is re-
moved.

Check the connection con-
ditions of the low tire pres-
sure warning control unit 
harness connector, and re-
pair if necessary.

Tire Pressure Monitoring 
System (TPMS) mal-
function.

• Perform CONSULT self-

diagnosis. Refer to 

WT-9, 

"AIR PRESSURE MONI-
TOR : CONSULT Func-
tion (BCM - AIR 
PRESSURE MONI-
TOR)"

• If necessary, perform tire 

pressure sensor ID regis-
tration. Refer to 

WT-18, 

"Work Procedure"

.

Hazard warning 
lamp

The hazard warn-
ing lamp does not 
blink twice when 
the tire pressure 
sensor is activated.

1.

The tire pressure 
sensor activation 
tool (J-45295) does 
not activate.

2.

The ignition switch 
is OFF when the 
tire pressure sen-
sor wake-up opera-
tion is performed.

3.

The tire pressure 
sensor activation 
tool (J-45295) is 
not used in the cor-
rect position.

4.

The tire pressure 
sensor is already 
waked up.

1.

Replace the battery in 
the tire pressure sen-
sor activation tool (J-
45295).

2.

Turn the ignition 
switch ON when per-
forming the tire pres-
sure sensor wake-up 
operation.

3.

Operate the tire pres-
sure sensor activation 
tool (J-45295) in the 
correct position when 
performing the wake-
up operation.

4.

No procedure.

Diagnosis items

Symptom

(Ignition switch 

ON)

Low tire pressure warning lamp

Cause

Action

SEIA0788E

Revision: 2012 September

2013 MURANO

WT-36

< SYMPTOM DIAGNOSIS >

LOW TIRE PRESSURE WARNING LAMP DOES NOT TURN ON

LOW TIRE PRESSURE WARNING LAMP DOES NOT TURN ON

Description

INFOID:0000000008454520

The low tire pressure warning lamp does not illuminate when the ignition switch is turned ON.
NOTE:
The low tire pressure warning lamp illuminates for approximately 1 second and then turns OFF when the igni-
tion switch is turned ON. This is to check that no abnormal condition is present in the tire pressure monitoring
system.
The lamp bulb may be burnt out or the tire pressure monitoring system may be malfunctioning if the low tire
pressure warning lamp does not illuminate when the ignition switch is turned ON.

Diagnosis Procedure

INFOID:0000000008454521

1.

CHECK LOW TIRE PRESSURE WARNING LAMP

Perform trouble diagnosis of the low tire pressure warning lamp. Refer to 

WT-31, "Diagnosis Procedure"

Is the inspection result normal?

YES

>> Check pin terminal and connection of each connector for damage and loose connection. 

NO

>> Repair or replace damaged parts.

Revision: 2012 September

2013 MURANO

LOW TIRE PRESSURE WARNING LAMP DOES NOT TURN OFF

WT-37

< SYMPTOM DIAGNOSIS >

C

D

F

G

H

I

J

K

L

M

A

B

WT

N

O

P

LOW TIRE PRESSURE WARNING LAMP DOES NOT TURN OFF

Description

INFOID:0000000008454522

The low tire pressure warning lamp does not turn OFF after several seconds is passed after engine starts.

Diagnosis Procedure

INFOID:0000000008454523

1.

CHECK TIRE PRESSURE

1.

Turn the ignition switch ON.

CAUTION:

Never start the engine.

2.

Check the tire pressure for all wheels and adjust to the specified value. Refer to 

WT-49, "Tire Air Pres-

sure"

Is the inspection result normal?

YES

>> GO TO 2.

NO

>> Inspect or repair the tires or wheels.

2.

CHECK LOW TIRE PRESSURE WARNING LAMP

Check low tire pressure warning lamp display.

Does not low tire pressure warning lamp turn OFF?

YES

>> GO TO 3.

NO

>> INSPECTION END

3.

CHECK BCM

With CONSULT

Perform “SELF-DIAG RESULTS” in “AIR PRESSURE MONITOR” of “BCM”.

Is any DTC detected?

YES

>> Check the DTC. Refer to 

BCS-77, "DTC Index"

.

NO

>> GO TO 4.

4.

CHECK BCM POWER SUPPLY AND GROUND CIRCUIT

Perform the trouble diagnosis for power supply and ground circuit. Refer to 

WT-32, "Diagnosis Procedure"

.

Is the inspection result normal?

YES

>> Replace BCM. Refer to 

BCS-84, "Exploded View"

NO

>> Repair or replace error-detected parts.

Revision: 2012 September

2013 MURANO

WT-38

< SYMPTOM DIAGNOSIS >

LOW TIRE PRESSURE WARNING LAMP BLINKS

LOW TIRE PRESSURE WARNING LAMP BLINKS

Description

INFOID:0000000008454524

The low tire pressure warning lamp blinks when the ignition switch is turned ON.
NOTE:
The position of an inactive tire pressure sensor can be identified by checking the blinking timing of the low tire
pressure warning lamp.

Diagnosis Procedure

INFOID:0000000008454525

1.

TIRE PRESSURE SENSOR WAKE-UP OPERATION

Perform the tire pressure sensor wake-up. Refer to 

WT-17, "Work Procedure"

.

Is the tire pressure sensor wake-up completed?

YES

>> GO TO 2.

NO

>> Perform trouble diagnosis for the tire pressure sensor. Refer to 

WT-22, "Diagnosis Procedure"

2.

TIRE PRESSURE SENSOR ID REGISTRATION

Perform tire pressure sensor ID registration. Refer to 

WT-18, "Work Procedure"

.

Is tire pressure sensor ID registration completed?

YES

>> INSPECTION END

NO

>> Perform the self-diagnosis for “AIR PRESSURE MONITOR”. Refer to 

BCS-77, "DTC Index"

.

JPEIC0089GB

Revision: 2012 September

2013 MURANO

 

 

 

 

 

 

 

Content      ..     94      95      96      97     ..