Content .. 68 69 70 71 ..

Nissan Murano Z51 (2013 year). Manual - part 70

CRASH ZONE SENSOR

SR-21

< REMOVAL AND INSTALLATION >

[FOR USA AND CANADA]

CRASH ZONE SENSOR

Exploded View

INFOID:0000000008457571

Removal and Installation

INFOID:0000000008457572

WARNING:

• Before servicing, turn ignition switch OFF, disconnect battery negative terminal and wait 3 minutes

or more.

• Never use air tools or electric tools for servicing.

REMOVAL

Remove the radiator cover grill (RH). Refer to

EM-30, "Exploded View"

Remove the air duct (inlet). Refer to

EM-30, "Exploded View"

Remove the crash zone sensor fixing nuts.

Disconnect the crash zone sensor harness connector, and then remove the crash zone sensor.

CAUTION:

• Never impact the crash zone sensor.
• Replace the crash zone sensor if it has been dropped or sus-

tained an impact.

• Replace the crash zone sensor of deployed SRS driver air bag and deployed SRS front passenger air

bag.

INSTALLATION

Crash zone sensor

: Crash zone sensor harness connector

: Always replace after every disassembly.

: N·m (kg-m, ft-lb)

JMHIA0515GB

JMHIA0009ZZ

Revision: 2012 September

2013 MURANO

SR-22

< REMOVAL AND INSTALLATION >

[FOR USA AND CANADA]

CRASH ZONE SENSOR

Install in the reverse order of removal.

CAUTION:

• Never use the old fixing nuts after removal, replace with the new nuts.
• If malfunction is detected by the air bag warning lamp, after repair or replacement of the malfunc-

tioning parts, reset the memory using self-diagnosis or CONSULT. Refer to

SRC-15, "Description"

• After the work is completed, check that no system malfunction is detected by air bag warning lamp.

Revision: 2012 September

2013 MURANO

SIDE AIR BAG (SATELLITE) SENSOR

SR-23

< REMOVAL AND INSTALLATION >

[FOR USA AND CANADA]

SIDE AIR BAG (SATELLITE) SENSOR

Exploded View

INFOID:0000000008457573

Removal and Installation

INFOID:0000000008457574

WARNING:

• Before servicing, turn ignition switch OFF, disconnect battery negative terminal and wait 3 minutes

or more.

• Never use the air tools or electric tools for servicing.

REMOVAL

Remove the front seat belt. Refer to

SB-7, "SEAT BELT RETRACTOR : Removal and Installation"

Remove the side air bag (satellite) sensor fixing nuts.

Disconnect the side air bag (satellite) sensor harness connector, and then remove the side air bag (satel-
lite) sensor.

CAUTION:

• Never impact the side air bag (satellite) sensor.
• Replace the side air bag (satellite) sensor if it has been

dropped or sustained an impact.

• Replace the side air bag (satellite) sensor of deployed SRS front side air bag module and deployed

SRS side curtain air bag module.

Side air bag (satellite) sensor

: Side air bag (satellite) sensor harness connector

: Always replace after every disassembly.

: N·m (kg-m, ft-lb)

JMHIA0516GB

JMHIA0009ZZ

Revision: 2012 September

2013 MURANO

SR-24

< REMOVAL AND INSTALLATION >

[FOR USA AND CANADA]

SIDE AIR BAG (SATELLITE) SENSOR

INSTALLATION

Install in the reverse order of removal.

CAUTION:

• Never use the old fixing nuts after removal, replace with the new nuts.
• If malfunction is detected by the air bag warning lamp, after repair or replacement of the malfunc-

tioning parts, reset the memory using self-diagnosis or CONSULT. Refer to

SRC-15, "Description"

• After the work is completed, check that no system malfunction is detected by air bag warning lamp.

Revision: 2012 September

2013 MURANO

DIAGNOSIS SENSOR UNIT

SR-25

< REMOVAL AND INSTALLATION >

[FOR USA AND CANADA]

DIAGNOSIS SENSOR UNIT

Exploded View

INFOID:0000000008457575

Removal and Installation

INFOID:0000000008457576

WARNING:

• Before servicing, turn ignition switch OFF, disconnect battery negative terminal and wait 3 minutes

or more.

• Before disconnecting the air bag sensor unit harness connector, be sure to disconnect the each har-

ness connector of the air bag module and pre-tensioner seat belt to prevent air bag deployment by
static electricity and pre-tensioner seat belt operation.

• Never use the air tools or electric tools for servicing.
• When replacing the air bag diagnosis sensor unit, always check with the parts department for the lat-

est parts information. Installing an incorrect air bag diagnosis sensor unit may or may not cause the
air bag warning lamp to illuminate and may cause incorrect deployment of the supplemental air bags
and seat belt pre-tensioners in a collision resulting in serious personal injury or death.

REMOVAL

Always check the air bag diagnosis sensor unit ECU discriminated number (identification number) using
CONSULT.

Disconnect the each connector of all air bag modules and pre-tensioner seat belts.

Remove the instrument lower cover (LH and RH). Refer to

IP-20, "Exploded View"

Remove the rear foot duct 1 (LH and RH). Refer to

VTL-125, "REAR FOOT DUCT 1 : Exploded View"

Remove the instrument stay LH. Refer to

IP-20, "Exploded View"

Remove the front console bracket. Refer to

IP-20, "Exploded View"

Disconnect the diagnosis sensor unit harness connectors.

Remove the fixing bolts, ground bolt, and then remove the diagnosis sensor unit.

CAUTION:

Diagnosis sensor unit

: Diagnosis sensor unit harness connector

: Ground bolt

: Always replace after every disassembly.

: N·m (kg-m, ft-lb)

JMHIA0517GB

Revision: 2012 September

2013 MURANO

SR-26

< REMOVAL AND INSTALLATION >

[FOR USA AND CANADA]

DIAGNOSIS SENSOR UNIT

• Replace the diagnosis sensor unit if it has been dropped or

sustained an impact.

• Replace the diagnosis sensor unit of deployed SRS air bag and deployed SRS front seat belt pre-ten-

sioner.

INSTALLATION

Install air bag diagnosis sensor unit in the reverse order of removal.

CAUTION:

• Never use the old fixing bolts after removal, replace with the new fixing bolts.
• If malfunction is detected by the air bag warning lamp, after repair or replacement of the malfunc-

tioning parts, reset the memory using self-diagnosis or CONSULT. Refer to

SRC-15, "Description"

• After the work is completed, check that no system malfunction is detected by air bag warning lamp.
• After replacing the air bag diagnosis sensor unit, confirm using CONSULT that the ECU discrimi-

nated number (identification number) of the new replacement air bag sensor unit matches the ECU
discriminated number (identification number) of the replaced (old) air bag diagnosis sensor unit.

NOTE:
If the ECU discriminated number of the new replacement air bag diagnosis sensor unit differs from the ECU
discriminated number of the replaced air bag diagnosis sensor unit, reconfirm the parts information and verify
that the correct air bag diagnosis sensor unit was installed.

JMHIA0009ZZ

Revision: 2012 September

2013 MURANO

FRONT SEAT BELT PRE-TENSIONER

SR-27

< REMOVAL AND INSTALLATION >

[FOR USA AND CANADA]

FRONT SEAT BELT PRE-TENSIONER

Removal and Installation

INFOID:0000000008457577

For removal and installation procedures, refer to

SB-7, "SEAT BELT RETRACTOR : Removal and Installa-

tion"

Revision: 2012 September

2013 MURANO

SR-28

< REMOVAL AND INSTALLATION >

[FOR USA AND CANADA]

OCCUPANT CLASSIFICATION SYSTEM CONTROL UNIT

OCCUPANT CLASSIFICATION SYSTEM CONTROL UNIT

Removal and Installation

INFOID:0000000008457578

For removal and installation

The occupant classification system control unit and seat sensor mat are an integral part of the front passenger
seat cushion and are replaced as an assembly. Refer to

SE-73, "Removal and Installation"

Revision: 2012 September

2013 MURANO

PRECAUTIONS

SR-29

< PRECAUTION >

[FOR MEXICO]

PRECAUTION

PRECAUTIONS

Precaution for Supplemental Restraint System (SRS) "AIR BAG" and "SEAT BELT
PRE-TENSIONER"

INFOID:0000000008457579

The Supplemental Restraint System such as “AIR BAG” and “SEAT BELT PRE-TENSIONER”, used along
with a front seat belt, helps to reduce the risk or severity of injury to the driver and front passenger for certain
types of collision. Information necessary to service the system safely is included in the “SRS AIR BAG” and
“SEAT BELT” of this Service Manual.

WARNING:

Always observe the following items for preventing accidental activation.
• To avoid rendering the SRS inoperative, which could increase the risk of personal injury or death in

the event of a collision that would result in air bag inflation, all maintenance must be performed by
an authorized NISSAN/INFINITI dealer.

• Improper maintenance, including incorrect removal and installation of the SRS, can lead to personal

injury caused by unintentional activation of the system. For removal of Spiral Cable and Air Bag
Module, see “SRS AIR BAG”.

• Never use electrical test equipment on any circuit related to the SRS unless instructed to in this Ser-

vice Manual. SRS wiring harnesses can be identified by yellow and/or orange harnesses or harness
connectors.

PRECAUTIONS WHEN USING POWER TOOLS (AIR OR ELECTRIC) AND HAMMERS

WARNING:

Always observe the following items for preventing accidental activation.
• When working near the Air Bag Diagnosis Sensor Unit or other Air Bag System sensors with the

ignition ON or engine running, never use air or electric power tools or strike near the sensor(s) with
a hammer. Heavy vibration could activate the sensor(s) and deploy the air bag(s), possibly causing
serious injury.

• When using air or electric power tools or hammers, always switch the ignition OFF, disconnect the

battery, and wait at least 3 minutes before performing any service.

Service

INFOID:0000000008457580

• Do not use electrical test equipment to check SRS circuits unless instructed to in this Service Manual.
• Before servicing the SRS, turn ignition switch OFF, disconnect battery negative terminal and wait at least 3

minutes.
For approximately 3 minutes after the battery negative terminal is removed, it is still possible for the air bag
and seat belt pre-tensioner to deploy. Therefore, do not work on any SRS connectors or wires until at least 3
minutes have elapsed.

• Diagnosis sensor unit must always be installed with their arrow marks “

⇐

” pointing towards the front of the

vehicle for proper operation. Also check diagnosis sensor unit for cracks, deformities or rust before installa-
tion and replace as required.

• The spiral cable must be aligned in the neutral position since its rotations are limited. Do not turn steering

wheel and column after removal of steering gear.

• Handle air bag module carefully. Always place driver and front passenger air bag modules with the pad side

facing upward and seat mounted front side air bag module standing with the stud bolt side facing down.

• Conduct self-diagnosis to check entire SRS for proper functioning after replacing any components.
• After air bag inflates, the front instrument panel assembly should be replaced if damaged.
• Always replace instrument panel pad following front passenger air bag deployment.

Revision: 2012 September

2013 MURANO

SR-30

< PREPARATION >

[FOR MEXICO]

PREPARATION

PREPARATION

Commercial Service Tools

INFOID:0000000008457581

Tool name

Description

Tamper resistant TORX bit

Removes driver air bag module

Remover tool

Removes clips, pawls, and metal clip

S-NT757

JMKIA3050ZZ

Revision: 2012 September

2013 MURANO

COLLISION DIAGNOSIS

SR-31

< BASIC INSPECTION >

[FOR MEXICO]

BASIC INSPECTION

COLLISION DIAGNOSIS

FOR FRONTAL COLLISION

FOR FRONTAL COLLISION : When SRS is activated in a collision

INFOID:0000000008457582

CAUTION:

Due to varying models and option levels, not all parts listed in the chart below apply to all vehicles.

WORK PROCEDURE

Before performing any of the following steps, ensure that all vehicle body and structural repairs have been
completed.

Replace the diagnosis sensor unit.

Remove the front air bag modules, crash zone sensor, bracket and seat belt pre-tensioner assemblies.

Check the SRS components using the table below:
Replace any SRS components showing visible signs of damage. (dents, cracks and deformation, etc.)

Install new front air bag modules, crash zone sensor assembly, bracket and seat belt pre-tensioner
assemblies.

Perform self-diagnosis using CONSULT or air bag warning lamp. Refer to

SRC-83, "Description"

for

details. Ensure entire SRS operates properly.

After the work is completed, perform self-diagnosis to check that no malfunction is detected. Refer to

SRC-83, "Description"

SRS INSPECTION (FOR FRONTAL COLLISION)

Part

Inspection

Driver air bag module

If the driver air bag has deployed:
REPLACE
Install with new fasteners.

Front passenger air bag module
(if equipped)

If the front passenger air bag has deployed:
REPLACE
Install with new fasteners.

Crash zone sensor

If any of the front air bags or seat belt pre-tensioners* have been activated:
REPLACE the crash zone sensor and bracket with new fasteners.
*: Confirm seat belt pre-tensioner activation using CONSULT only.

Seat belt pre-tensioner assem-
blies
(All applicable locations: buckle,
retractor, lap outer)

If either the driver or passenger seat belt pre-tensioner* has been activated:
REPLACE all seat belt pre-tensioner assemblies with new fasteners.
*: Confirm seat belt pre-tensioner activation using CONSULT only.

Diagnosis sensor unit

If any of the SRS components have been activated:
REPLACE the diagnosis sensor unit.
Install with new fasteners.

Steering wheel

Visually check steering wheel for deformities.

Check harness (built into steering wheel) and connectors for damage, and terminals for defor-
mities.

Install driver air bag module into the steering wheel to check fit and alignment with the wheel.

Check steering wheel for excessive free play.

If no damage is found, reinstall.

If damaged

−

REPLACE.

Spiral cable

If the driver front air bag has deployed:
REPLACE the spiral cable.

Occupant classification system
(Passenger seat)

Remove passenger seat assembly.

Check control unit case for dents, cracks of deformities.

Check connectors and pressure sensor tube for damage, and terminals for deformities.

Check seat frame and cushion pan for dents or deformities.

If no damage is found, reinstall seat with new fasteners.

If damaged

−

REPLACE seat cushion assembly with new fasteners.

Revision: 2012 September

2013 MURANO

SR-32

< BASIC INSPECTION >

[FOR MEXICO]

COLLISION DIAGNOSIS

FOR FRONTAL COLLISION : When SRS is not activated in a collision

INFOID:0000000008457583

CAUTION:

Due to varying models and option levels, not all parts listed in the chart below apply to all vehicles.

WORK PROCEDURE

Before performing any of the following steps, ensure that all vehicle body and structural repairs have been
completed.

Check the SRS components using the table below:
Replace any SRS components showing visible signs of damage. (dents, cracks and deformation, etc.)

Perform self-diagnosis using CONSULT or air bag warning lamp. Refer to

SRC-83, "Description"

for

details. Ensure entire SRS operates properly.

After the work is completed, perform self-diagnosis to check that no malfunction is detected. Refer to

SRC-83, "Description"

SRS INSPECTION (FOR FRONTAL COLLISION)

Harness and connectors

Check connectors for poor connection, damage, and terminals for deformities.

Check harness for binding, chafing, cuts, or deformities.

If no damage is found, reinstall the harness and connectors.

If damaged

−

REPLACE the damaged harness. Do not attempt to repair, splice or modify any

SRS harness.

Instrument panel assembly

If the front passenger air bag has deployed:
REPLACE the instrument panel assembly. (integrated type)

Part

Inspection

Part

Inspection

Driver air bag module

If the driver air bag has NOT been deployed:
1.

Remove driver air bag module. Check harness cover and connectors for damage, terminals for
deformities, and harness for binding.

Install driver air bag module into the steering wheel to check fit and alignment with the wheel.

If no damage is found, reinstall with new fasteners.

If damaged

−

REPLACE. Install driver air bag module with new fasteners.

Front passenger air bag module
(if equipped)

If the front passenger air bag has NOT been deployed:
1.

Remove front passenger air bag module. Check harness cover and connectors for damage, ter-
minals for deformities, and harness for binding.

Install front passenger air bag module into the instrument panel to check fit with the instrument
panel.

If no damage is found, reinstall with new fasteners.

If damaged

−

REPLACE. Install front passenger air bag modules with new fasteners.

Crash zone sensor

If the front air bags or seat belt pre-tensioners have NOT been activated:
1.

Remove the crash zone sensor. Check harness connectors for damage, terminals for deformi-
ties, and harness for binding.

Check for visible signs of damage (dents, cracks, deformation, etc.) of the crash zone sensor
and bracket.

Install the crash zone sensor to check fit.

If no damage is found, reinstall with new fasteners.

If damaged

−

REPLACE the crash zone sensor and bracket with new fasteners.

Seat belt pre-tensioner assem-
blies
(All applicable locations: buckle,
retractor, lap outer)

If the pre-tensioners have NOT been activated:
1.

Remove seat belt pre-tensioners.
Check harness cover and connectors for damage, terminals for deformities, and harness for
binding.

Check belts for damage and anchors for loose mounting.

Check retractor for smooth operation.

Check seat belt adjuster for damage.

Check for deformities of the center pillar inner.

If the center pillar inner has no damage, REPLACE the seat belt pre-tensioner assembly.

If no damage is found, reinstall seat belt pre-tensioner assembly.

If damaged

−

REPLACE. Install the seat belt pre-tensioners with new fasteners.

Revision: 2012 September

2013 MURANO

COLLISION DIAGNOSIS

SR-33

< BASIC INSPECTION >

[FOR MEXICO]

FOR SIDE AND ROLLOVER COLLISION

FOR SIDE AND ROLLOVER COLLISION : When SRS is activated in a collision

INFOID:0000000008457584

CAUTION:

Due to varying models and option levels, not all parts listed in the chart below apply to all vehicles.

WORK PROCEDURE

Before performing any of the following steps, ensure that all vehicle body and structural repairs have been
completed.

Replace the following components:
• Front seat back assembly (on the side on which side air bag is activated)
• Door finisher (on the side on which door-mounted curtain air bag is activated)
• Pop-up roll bar assemblies and pop-up roll bar covers
• Side air bag (satellite) sensor LH/RH (on the side on which side air bag is activated)
• Diagnosis sensor unit
• Seat belt pre-tensioner assemblies

Check the SRS components and the related parts using the following table.
Replace any SRS components and the related parts showing visible signs of damage. (dents, cracks,
deformation, etc.)

Perform self-diagnosis using CONSULT and “AIR BAG” warning lamp. Refer to

SRC-83, "Description"

for

details. Make sure entire SRS operates properly.

After the work is completed, perform self-diagnosis to check that no malfunction is detected. Refer to

SRC-83, "Description"

Diagnosis sensor unit

If none of the SRS components have been activated:
1.

Check case for dents, cracks or deformities.

Check connectors for damage, and terminals for deformities.

If no damage is found, reinstall with new fasteners.

If damaged

−

REPLACE. Install diagnosis sensor unit with new fasteners.

Steering wheel

Visually check steering wheel for deformities.

Check harness (built into steering wheel) and connectors for damage, and terminals for defor-
mities.

Install driver air bag module into the steering wheel to check fit and alignment with the wheel.

Check steering wheel for excessive free play.

If no damage is found, reinstall.

If damaged

−

REPLACE.

Spiral cable

If the driver front air bag has not deployed:
1.

Visually check spiral cable and combination switch for damage.

Check connectors and protective tape for damage.

Check steering wheel for noise, binding or heavy operation.

If no damage is found, reinstall.

If damaged

−

REPLACE.

Occupant classification system
(Passenger seat)

Remove passenger seat assembly.

Check control unit case for dents, cracks of deformities.

Check connectors and pressure sensor tube for damage, and terminals for deformities.

Check seat frame and cushion pan for dents or deformities.

If no damage is found, reinstall seat with new fasteners.

If damaged

−

REPLACE seat cushion assembly with new fasteners.

Harness and connectors

Check connectors for poor connection, damage, and terminals for deformities.

Check harness for binding, chafing, cuts, or deformities.

If no damage is found, reinstall the harness and connectors.

If damaged

−

REPLACE the damaged harness. Do not attempt to repair, splice or modify any

SRS harness.

Instrument panel assembly

If the front passenger air bag has NOT deployed:
1.

Visually check instrument panel assembly for damage.

If no damage is found, reinstall the instrument panel assembly.

If damaged

−

REPLACE the instrument panel assembly.

Part

Inspection

Revision: 2012 September

2013 MURANO

SR-34

< BASIC INSPECTION >

[FOR MEXICO]

COLLISION DIAGNOSIS

SRS INSPECTION (FOR SIDE AND ROLLOVER COLLISION)

FOR SIDE AND ROLLOVER COLLISION : When SRS is not activated in a collision

INFOID:0000000008457585

CAUTION:

Due to varying models and option levels, not all parts listed in the chart below apply to all vehicles.

WORK PROCEDURE

Before performing any of the following steps, ensure that all vehicle body and structural repairs have been
completed.

Check the SRS components and the related parts using the following table.
• If the front seat back assembly is damaged, the front seat back assembly must be replaced.
• If the door finisher assembly is damaged, the door finisher assembly and door-mounted curtain air bag

module must be replaced.

Perform self-diagnosis using CONSULT and “AIR BAG” warning lamp. Refer to

SRC-83, "Description"

for

details. Make sure entire SRS operates properly.

After the work is completed, perform self-diagnosis to check that no malfunction is detected. Refer to

SRC-83, "Description"

SRS INSPECTION (FOR SIDE AND ROLLOVER COLLISION)

Part

Inspection

Side curtain air bag module LH

If the side curtain air bag LH has deployed:
REPLACE the side curtain air bag module LH.
Install with new fasteners.

Side curtain air bag module RH

If the side curtain air bag RH has deployed:
REPLACE the side curtain air bag module RH.
Install with new fasteners.

Front side air bag module LH

If the front side air bag LH has deployed:
REPLACE front seatback assembly LH.

Front side air bag module RH

If the front side air bag RH has deployed:
REPLACE front seatback assembly RH.

Side air bag (satellite) sensor
(LH or RH)

If any of the SRS components have deployed:
REPLACE the side air bag (satellite) sensor on the collision side with new fasteners.

Diagnosis sensor unit

If any of the SRS components have deployed:
REPLACE the diagnosis sensor unit with new fasteners.

Seat belt pre-tensioner assem-
blies
(All applicable locations: buckle,
retractor, lap outer)

Center inner pillar

Check the center inner pillar on the collision side for damage (dents, cracks, deformation, etc.).

If damaged

−

REPAIR the center inner pillar.

Trim/headlining

Check for visible signs of damage (dents, cracks, deformation, etc.) of the interior trim on the
collision side.

If damaged

−

REPLACE the damaged trim parts.

Door-mounted curtain air bag
module LH

If the door-mounted curtain air bag module LH has deployed:
REPLACE the door finisher LH and door-mounted curtain air bag module.
Install with new fasteners.

Door-mounted curtain air bag
module RH

If the door-mounted curtain air bag module RH has deployed:
REPLACE the door finisher RH and door-mounted curtain air bag module.
Install with new fasteners.

Pop-up roll bar assemblies

If the pop-up roll bar has deployed:
REPLACE pop-up roll bar assemblies and pop-up roll bar covers.
Install with new fasteners.

Revision: 2012 September

2013 MURANO

COLLISION DIAGNOSIS

SR-35

< BASIC INSPECTION >

[FOR MEXICO]

Part

Inspection

Side curtain air bag module LH

If the side curtain air bag LH has NOT deployed:
1.

Check for visible signs of damage (dents, tears, deformation, etc.) of the center pillar on the col-
lision side.

If damaged

−

Remove the side curtain air bag module LH.

Check for visible signs of damage (tears etc.) of the side curtain air bag module LH.

Check harness and connectors for damage, and terminals for deformities.

If no damage is found, reinstall the side curtain air bag module LH with new fasteners.

If damaged

−

REPLACE the side curtain air bag module LH with new fasteners.

Side curtain air bag module RH

If the side curtain air bag RH has NOT deployed:
1.

Check for visible signs of damage (dents, tears, deformation, etc.) of the center pillar on the col-
lision side.

If damaged

−

Remove the side curtain air bag module RH.

Check for visible signs of damage (tears etc.) of the side curtain air bag module RH.

Check harness and connectors for damage, and terminals for deformities.

If no damage is found, reinstall the side curtain air bag module RH with new fasteners.

If damaged

−

REPLACE the side curtain air bag module RH with new fasteners.

Front side air bag module LH

If the front side air bag LH has NOT deployed:
1.

Check for visible signs of damage (dents, tears, deformation, etc.) of the seat back on the col-
lision side.

Check harness and connectors for damage, and terminals for deformities.

If damaged

−

REPLACE the front seatback assembly LH.

Front side air bag module RH

If the front side air bag RH has NOT deployed:
1.

Check for visible signs of damage (dents, tears, deformation, etc.) of the seat back on the col-
lision side.

Check harness and connectors for damage, and terminals for deformities.

If damaged

−

REPLACE the front seatback assembly RH.

Side air bag (satellite) sensor
(LH or RH)

If none of the SRS components have been activated:
1.

Remove the side air bag (satellite) sensor (LH or RH) on the collision side. Check harness con-
nectors for damage, terminals for deformities, and harness for binding.

Check for visible signs of damage (dents, cracks, deformation, etc.) of the side air bag (satellite)
sensor (LH or RH).

Install the side air bag (satellite) sensor (LH or RH) to check fit.

If no damage is found, reinstall the side sir bag (satellite) sensor (LH or RH) with new fasteners.

If damaged

−

REPLACE the side air bag (satellite) sensor (LH or RH) with new fasteners.

Diagnosis sensor unit

If none of the SRS components have been activated:
1.

Check case and bracket for dents, cracks or deformities.

Check connectors for damage, and terminals for deformities.

If no damage is found, reinstall the diagnosis sensor unit with new fasteners.

If damaged

−

REPLACE the diagnosis sensor unit with new fasteners.

Seat belt pre-tensioner assem-
blies
(All applicable locations: buckle,
retractor, lap outer)

If the pre-tensioners have NOT been activated:
1.

Remove seat belt pre-tensioners.
Check harness cover and connectors for damage, terminals for deformities, and harness for
binding.

Check belts for damage and anchors for loose mounting.

Check retractor for smooth operation.

Check seat belt adjuster for damage.

Check for deformities of the center pillar inner.

If the center pillar inner has no damage, REPLACE the seat belt pre-tensioner assembly.

If no damage is found, reinstall seat belt pre-tensioner assembly.

If damaged

−

REPLACE. Install the seat belt pre-tensioners with new fasteners.

Seat (with front side air bag)

If the front LH or front RH side air bag modules have NOT deployed:
1.

Visually check the seat on the collision side.

Remove the seat on the collision side and check the following for damage and deformities.

Harness, connectors and terminals

Frame and recliner (for front and rear seat), and also adjuster and slides (for front seat)

If no damage is found, reinstall the seat.

If damaged

−

REPLACE the damaged seat parts using new fasteners. If the front seat back is

damaged, the front seat back assembly must be replaced.

Center inner pillar

Check the center inner pillar on the collision side for damage (dents, cracks, deformation, etc.).

If damaged

−

REPAIR the center inner pillar.

Revision: 2012 September

2013 MURANO

SR-36

< BASIC INSPECTION >

[FOR MEXICO]

COLLISION DIAGNOSIS

Trim/headlining

Check for visible signs of damage (dents, cracks, deformation, etc.) of the interior trim on the
collision side.

If damaged

−

REPLACE the damaged trim parts.

Door-mounted curtain air bag
module LH

If the door-mounted curtain air bag LH has NOT deployed:
1.

Check for visible signs of damage (dents, tears, deformation, etc.) of the door finisher on the
collision side.

If damaged

−

REPLACE the door finisher LH with new fasteners.

Check for visible signs of damaged (tears etc.) of the door-mounted curtain air bag module LH.

Check harness and connectors for damage, and terminals for deformities.

If no damage is found, reinstall door finisher.

CAUTION:

When removing door-mounted curtain air bag module from door finisher, never reuse
door finisher.

If damaged

−

REPLACE the door finisher LH and door-mounted curtain air bag module LH with

new fasteners.

Door-mounted curtain air bag
module RH

If the door-mounted curtain air bag RH has NOT deployed:
1.

Check for visible signs of damage (dents, tears, deformation, etc.) of the door finisher on the
collision side.

If damaged

−

REPLACE the door finisher RH with new fasteners.

Check for visible signs of damage (tears etc.) of the door-mounted curtain air bag module RH.

Check harness and connectors for damage, and terminals for deformities.

If no damage is found, reinstall door finisher.

CAUTION:

When removing door-mounted curtain air bag module from door finisher, never reuse
door finisher.

If damaged

−

REPLACE the door finisher RH and door-mounted curtain air bag module RH with

new fasteners.

Pop-up roll bar

If the pop-up roll bar has NOT deployed:
1.

Check for visible signs of damage (dents, tears, deformation, etc.) of the pop-up roll bar.

If damaged

−

REPLACE the pop-up roll bar with new fasteners.

Check harness and connectors for damage, and terminals for deformities.

If no damage is found, reinstall the pop-up roll bar with new fasteners.

Check for visible signs of damage (dents, cracks, deformation, etc.) of the seatback support
brace assembly.

If damaged

−

REPAIR the seatback support brace assembly.

Part

Inspection

Revision: 2012 September

2013 MURANO

Content .. 68 69 70 71 ..