Nissan Murano Z51 (2013 year). Manual - part 64

 

  Index      Manuals     Nissan Murano Z51 (2013 year) - Service and Repair Manual

 

Search            copyright infringement  

 

 

 

 

 

 

 

 

Content      ..     62      63      64      65     ..

 

 

Nissan Murano Z51 (2013 year). Manual - part 64

 

 

AUTO OPERATION DOES NOT OPERATE BUT MANUAL OPERATES NORMAL-

LY

PWC-83

< SYMPTOM DIAGNOSIS >

C

D

E

F

G

H

I

J

L

M

A

B

PWC

N

O

P

AUTO OPERATION DOES NOT OPERATE BUT MANUAL OPERATES
NORMALLY

DRIVER SIDE

DRIVER SIDE : Diagnosis Procedure

INFOID:0000000008458069

1.

PERFORM INITIALIZATION PROCEDURE

Initialization procedure is executed and operation is confirmed.
Refer to 

PWC-5, "ADDITIONAL SERVICE WHEN REMOVING BATTERY NEGATIVE TERMINAL : Special

Repair Requirement"

.

Is the inspection result normal?

YES

>> INSPECTION END

NO

>> GO TO 2.

2.

CHECK ENCODER (DRIVER SIDE) CIRCUIT

Check encoder (driver side) circuit. 
Refer to 

PWC-27, "DRIVER SIDE : Component Function Check"

.

Is the inspection result normal?

YES

>> GO TO 3.

NO

>> Repair or replace the malfunctioning parts.

3.

CONFIRM THE OPERATION

Confirm the operation again.

Is the result normal?

YES

>> Check intermittent incident. Refer to 

GI-45, "Intermittent Incident"

.

NO

>> GO TO 1.

PASSENGER SIDE

PASSENGER SIDE : Diagnosis Procedure

INFOID:0000000008458070

1.

PERFORM INITIALIZAITON PROCEDURE

Initialization procedure is executed and operation is confirmed.
Refer to 

PWC-5, "ADDITIONAL SERVICE WHEN REMOVING BATTERY NEGATIVE TERMINAL : Special

Repair Requirement"

.

Is the inspection result normal?

YES

>> INSPECTION END

NO

>> GO TO 2.

2.

CHECK ENCODER (PASSENGER SIDE) CIRCUIT

Check encoder (passenger side) circuit. 
Refer to 

PWC-29, "PASSENGER SIDE : Component Function Check"

.

Is the inspection result normal?

YES

>> GO TO 3.

NO

>> Repair or replace the malfunctioning parts.

3.

CONFIRM THE OPERATION

Confirm the operation again.
Is the result normal?

YES

>> Check intermittent incident. Refer to 

GI-45, "Intermittent Incident"

.

NO

>> GO TO 1.

Revision: 2012 September

2013 MURANO

PWC-84

< SYMPTOM DIAGNOSIS >

ANTI-PINCH FUNCTION DOES NOT OPERATE NORMALLY

ANTI-PINCH FUNCTION DOES NOT OPERATE NORMALLY

DRIVER SIDE

DRIVER SIDE : Diagnosis Procedure

INFOID:0000000008458071

1.

CHECK POWER WINDOW AUTO OPERATION

Check power window auto operation.

Is the inspection result normal?

YES

>> GO TO 2.

NO

>> Refer to 

PWC-83, "DRIVER SIDE : Diagnosis Procedure"

.

2.

CONFIRM THE OPERATION

Confirm the operation again.

Is the result normal?

YES

>> Check intermittent incident. Refer to 

GI-45, "Intermittent Incident"

.

NO

>> GO TO 1.

PASSENGER SIDE

PASSENGER SIDE : Diagnosis Procedure

INFOID:0000000008458072

1.

CHECK POWER WINDOW AUTO OPERATION

Check power window auto operation.
Is the inspection result normal?

YES

>> GO TO 2.

NO

>> Refer to 

PWC-83, "PASSENGER SIDE : Diagnosis Procedure"

.

2.

CONFIRM THE OPERATION

Confirm the operation again.

Is the result normal?

YES

>> Check intermittent incident. Refer to 

GI-45, "Intermittent Incident"

.

NO

>> GO TO 1.

Revision: 2012 September

2013 MURANO

POWER WINDOW RETAINED POWER OPERATION DOES NOT OPERATE 

PROPERLY

PWC-85

< SYMPTOM DIAGNOSIS >

C

D

E

F

G

H

I

J

L

M

A

B

PWC

N

O

P

POWER WINDOW RETAINED POWER OPERATION DOES NOT OPER-
ATE PROPERLY

Diagnosis Procedure

INFOID:0000000008458073

1.

CHECK DOOR SWITCH

Check door switch. 
Refer to 

DLK-97, "WITH AUTOMATIC BACK DOOR : Component Function Check"

.

Is the inspection result normal?

YES

>> GO TO 2.

NO

>> Repair or replace the malfunctioning parts.

2.

CONFIRM THE OPERATION

Confirm the operation again.

Is the result normal?

YES

>> Check intermittent incident. Refer to 

GI-45, "Intermittent Incident"

.

NO

>> GO TO 1.

Revision: 2012 September

2013 MURANO

PWC-86

< SYMPTOM DIAGNOSIS >

DOOR KEY CYLINDER SWITCH DOES NOT OPERATE POWER WINDOWS

DOOR KEY CYLINDER SWITCH DOES NOT OPERATE POWER WIN-
DOWS

Diagnosis Procedure

INFOID:0000000008458074

1.

PERFORM INITIALIZATION PROCEDURE

Initialization procedure is executed and operation is confirmed.
Refer to

PWC-5, "ADDITIONAL SERVICE WHEN REMOVING BATTERY NEGATIVE TERMINAL : Special

Repair Requirement"

.

Is the inspection result normal?

YES

>> INSPECTION END

NO

>> GO TO 2.

2.

CHECK DRIVER SIDE DOOR LOCK ASSEMBLY (DOOR KEY CYLINDER SWITCH)

Check driver side door lock assembly (door key cylinder switch).
Refer to 

DLK-110, "Component Function Check"

.

Is the inspection result normal?

YES

>> GO TO 3.

NO

>> Repair or replace the malfunctioning parts.

3.

CONFIRM THE OPERATION

Confirm the operation again.

Is the result normal?

YES

>> Check intermittent incident. Refer to 

GI-45, "Intermittent Incident"

.

NO

>> GO TO 1.

Revision: 2012 September

2013 MURANO

KEYLESS POWER WINDOW DOWN DOES NOT OPERATE

PWC-87

< SYMPTOM DIAGNOSIS >

C

D

E

F

G

H

I

J

L

M

A

B

PWC

N

O

P

KEYLESS POWER WINDOW DOWN DOES NOT OPERATE

Diagnosis Procedure

INFOID:0000000008458075

1.

 CHECK INTELLIGENT KEY FUNCTION

Check Intelligent Key function.
Refer to 

DLK-127, "Component Function Check"

.

Is the inspection result normal?

YES

>> GO TO 2.

NO

>> Replace BCM. Refer to 

BCS-84, "Exploded View"

.

2.

 CONFIRM THE OPERATION

Confirm the operation again.

Is the inspection result normal?

YES

>> Check intermittent incident. Refer to 

GI-45, "Intermittent Incident"

.

NO

>> GO TO 1.

Revision: 2012 September

2013 MURANO

PWC-88

< SYMPTOM DIAGNOSIS >

POWER WINDOW LOCK SWITCH DOES NOT FUNCTION

POWER WINDOW LOCK SWITCH DOES NOT FUNCTION

Diagnosis Procedure

INFOID:0000000008458076

1.

REPLACE POWER WINDOW MAIN SWITCH 

Replace power window main switch. 

>> Refer to

PWC-92, "Removal and Installation"

.

Revision: 2012 September

2013 MURANO

POWER WINDOW SWITCH ILLUMINATION DOES NOT ILLUMINATE

PWC-89

< SYMPTOM DIAGNOSIS >

C

D

E

F

G

H

I

J

L

M

A

B

PWC

N

O

P

POWER WINDOW SWITCH ILLUMINATION DOES NOT ILLUMINATE

Diagnosis Procedure

INFOID:0000000008458077

1.

REPLACE POWER WINDOW MAIN SWITCH 

Replace power window main switch. 

>> Refer to

PWC-92, "Removal and Installation"

.

Revision: 2012 September

2013 MURANO

PWC-90

< PRECAUTION >

PRECAUTIONS

PRECAUTION

PRECAUTIONS

FOR USA AND CANADA

FOR USA AND CANADA : Precaution for Supplemental Restraint System (SRS) "AIR 
BAG" and "SEAT BELT PRE-TENSIONER"

INFOID:0000000008458078

The Supplemental Restraint System such as “AIR BAG” and “SEAT BELT PRE-TENSIONER”, used along
with a front seat belt, helps to reduce the risk or severity of injury to the driver and front passenger for certain
types of collision. This system includes seat belt switch inputs and dual stage front air bag modules. The SRS
system uses the seat belt switches to determine the front air bag deployment, and may only deploy one front
air bag, depending on the severity of a collision and whether the front occupants are belted or unbelted.
Information necessary to service the system safely is included in the “SRS AIR BAG” and “SEAT BELT” of this
Service Manual.

WARNING:

Always observe the following items for preventing accidental activation.
• To avoid rendering the SRS inoperative, which could increase the risk of personal injury or death in

the event of a collision that would result in air bag inflation, all maintenance must be performed by
an authorized NISSAN/INFINITI dealer.

• Improper maintenance, including incorrect removal and installation of the SRS, can lead to personal

injury caused by unintentional activation of the system. For removal of Spiral Cable and Air Bag
Module, see “SRS AIR BAG”.

• Never use electrical test equipment on any circuit related to the SRS unless instructed to in this Ser-

vice Manual. SRS wiring harnesses can be identified by yellow and/or orange harnesses or harness
connectors.

PRECAUTIONS WHEN USING POWER TOOLS (AIR OR ELECTRIC) AND HAMMERS

WARNING:

Always observe the following items for preventing accidental activation.
• When working near the Air Bag Diagnosis Sensor Unit or other Air Bag System sensors with the

ignition ON or engine running, never use air or electric power tools or strike near the sensor(s) with
a hammer. Heavy vibration could activate the sensor(s) and deploy the air bag(s), possibly causing
serious injury.

• When using air or electric power tools or hammers, always switch the ignition OFF, disconnect the

battery, and wait at least 3 minutes before performing any service.

FOR USA AND CANADA : Precaution for Procedure without Cowl Top Cover

INFOID:0000000008458079

When performing the procedure after removing cowl top cover, cover
the lower end of windshield with urethane, etc to prevent damage to
windshield.

FOR MEXICO

FOR MEXICO : Precaution for Supplemental Restraint System (SRS) "AIR BAG" and 
"SEAT BELT PRE-TENSIONER"

INFOID:0000000008458080

The Supplemental Restraint System such as “AIR BAG” and “SEAT BELT PRE-TENSIONER”, used along
with a front seat belt, helps to reduce the risk or severity of injury to the driver and front passenger for certain
types of collision. Information necessary to service the system safely is included in the “SRS AIR BAG” and
“SEAT BELT” of this Service Manual.

PIIB3706J

Revision: 2012 September

2013 MURANO

PRECAUTIONS

PWC-91

< PRECAUTION >

C

D

E

F

G

H

I

J

L

M

A

B

PWC

N

O

P

WARNING:

Always observe the following items for preventing accidental activation.
• To avoid rendering the SRS inoperative, which could increase the risk of personal injury or death in

the event of a collision that would result in air bag inflation, all maintenance must be performed by
an authorized NISSAN/INFINITI dealer.

• Improper maintenance, including incorrect removal and installation of the SRS, can lead to personal

injury caused by unintentional activation of the system. For removal of Spiral Cable and Air Bag
Module, see “SRS AIR BAG”.

• Never use electrical test equipment on any circuit related to the SRS unless instructed to in this Ser-

vice Manual. SRS wiring harnesses can be identified by yellow and/or orange harnesses or harness
connectors.

PRECAUTIONS WHEN USING POWER TOOLS (AIR OR ELECTRIC) AND HAMMERS

WARNING:

Always observe the following items for preventing accidental activation.
• When working near the Air Bag Diagnosis Sensor Unit or other Air Bag System sensors with the

ignition ON or engine running, never use air or electric power tools or strike near the sensor(s) with
a hammer. Heavy vibration could activate the sensor(s) and deploy the air bag(s), possibly causing
serious injury.

• When using air or electric power tools or hammers, always switch the ignition OFF, disconnect the

battery, and wait at least 3 minutes before performing any service.

FOR MEXICO : Precaution for Procedure without Cowl Top Cover

INFOID:0000000008458081

When performing the procedure after removing cowl top cover, cover
the lower end of windshield with urethane, etc to prevent damage to
windshield.

PIIB3706J

Revision: 2012 September

2013 MURANO

PWC-92

< REMOVAL AND INSTALLATION >

POWER WINDOW MAIN SWITCH

REMOVAL AND INSTALLATION

POWER WINDOW MAIN SWITCH

Exploded View

INFOID:0000000008458082

NOTE:
The same procedure is also performed for front power window switch (passenger side) and rear power switch
(LH & RH). 
Refer to removal and installation procedure. Refer to 

PWC-92, "Removal and Installation"

.

Removal and Installation

INFOID:0000000008458083

REMOVAL

1.

Remove the power window main switch finisher (2).
Refer to 

INT-12, "FRONT DOOR FINISHER : Exploded View"

and 

INT-12, "FRONT DOOR FINISHER : Removal and Installa-

tion"

.

2.

Power window main switch (1) is removed from power window
main switch finisher (2) using remover tool (A). 

CAUTION:

Do not fold the pawl of power window main switch finisher.
NOTE:
The same procedure is also performed for front power window
switch (passenger side) and rear power window switch (LH & RH).

INSTALLATION

Install in the reverse order of removal.
NOTE:
Power window main switch is exchanged or is detached it is necessary to do the initialization procedure. 
Refer to 

PWC-6, "ADDITIONAL SERVICE WHEN REPLACING CONTROL UNIT : Special Repair Require-

ment"

.

JMKIA1823ZZ

1.

Power window main switch

2.

Power window main switch finisher

JMKIA1822ZZ

Revision: 2012 September

2013 MURANO

PWO

PWO-1

ELECTRICAL & POWER CONTROL

C

D

E

F

G

H

I

J

K

L

B

SECTION 

PWO

A

O

P

N

CONTENTS

POWER OUTLET

DTC/CIRCUIT DIAGNOSIS  ..........................

2

CIGARETTE LIGHTER  .......................................

2

Wiring Diagram - CIGARETTE LIGHTER -  ...............

2

POWER SOCKET  ...............................................

3

Wiring Diagram - POWER SOCKET - .......................

3

PRECAUTION ...............................................

4

PRECAUTIONS ...................................................

4

FOR USA AND CANADA ............................................

4

FOR USA AND CANADA : Precaution for Supple-
mental Restraint System (SRS) "AIR BAG" and 
"SEAT BELT PRE-TENSIONER" ............................
..

4

FOR MEXICO  ..............................................................

4

FOR MEXICO : Precaution for Supplemental Re-
straint System (SRS) "AIR BAG" and "SEAT BELT 
PRE-TENSIONER" .................................................
..

4

REMOVAL AND INSTALLATION ................

6

CIGARETTE LIGHTER  ......................................

6

Exploded View ..........................................................

6

Removal and Installation  ..........................................

6

POWER SOCKET  ..............................................

7

FRONT POWER SOCKET ..........................................

7

FRONT POWER SOCKET : Exploded View  ............

7

FRONT POWER SOCKET : Removal and Instal-
lation ........................................................................
.

7

CONSOLE POWER SOCKET  ....................................

7

CONSOLE POWER SOCKET : Exploded View .......

7

CONSOLE POWER SOCKET : Removal and In-
stallation ..................................................................
.

7

LUGGAGE ROOM POWER SOCKET ........................

8

LUGGAGE ROOM POWER SOCKET : Exploded 
View .........................................................................
.

8

LUGGAGE ROOM POWER SOCKET : Removal 
and Installation  ........................................................
.

8

Revision: 2012 September

2013 MURANO

PWO-2

< DTC/CIRCUIT DIAGNOSIS >

CIGARETTE LIGHTER

DTC/CIRCUIT DIAGNOSIS

CIGARETTE LIGHTER

Wiring Diagram - CIGARETTE LIGHTER -

INFOID:0000000008459797

For connector terminal arrangements, harness layouts, and alphabets in a 

 (option abbreviation; if not

described in wiring diagram), refer to 

GI-12, "Connector Information"

.

JRMWD4428GB

Revision: 2012 September

2013 MURANO

PWO

POWER SOCKET

PWO-3

< DTC/CIRCUIT DIAGNOSIS >

C

D

E

F

G

H

I

J

K

L

B

A

O

P

N

POWER SOCKET

Wiring Diagram - POWER SOCKET -

INFOID:0000000008459798

For connector terminal arrangements, harness layouts, and alphabets in a 

 (option abbreviation; if not

described in wiring diagram), refer to 

GI-12, "Connector Information"

.

JRMWD4429GB

Revision: 2012 September

2013 MURANO

PWO-4

< PRECAUTION >

PRECAUTIONS

PRECAUTION

PRECAUTIONS

FOR USA AND CANADA

FOR USA AND CANADA : Precaution for Supplemental Restraint System (SRS) "AIR 
BAG" and "SEAT BELT PRE-TENSIONER"

INFOID:0000000008459799

The Supplemental Restraint System such as “AIR BAG” and “SEAT BELT PRE-TENSIONER”, used along
with a front seat belt, helps to reduce the risk or severity of injury to the driver and front passenger for certain
types of collision. This system includes seat belt switch inputs and dual stage front air bag modules. The SRS
system uses the seat belt switches to determine the front air bag deployment, and may only deploy one front
air bag, depending on the severity of a collision and whether the front occupants are belted or unbelted.
Information necessary to service the system safely is included in the “SRS AIR BAG” and “SEAT BELT” of this
Service Manual.

WARNING:

Always observe the following items for preventing accidental activation.
• To avoid rendering the SRS inoperative, which could increase the risk of personal injury or death in

the event of a collision that would result in air bag inflation, all maintenance must be performed by
an authorized NISSAN/INFINITI dealer.

• Improper maintenance, including incorrect removal and installation of the SRS, can lead to personal

injury caused by unintentional activation of the system. For removal of Spiral Cable and Air Bag
Module, see “SRS AIR BAG”.

• Never use electrical test equipment on any circuit related to the SRS unless instructed to in this Ser-

vice Manual. SRS wiring harnesses can be identified by yellow and/or orange harnesses or harness
connectors.

PRECAUTIONS WHEN USING POWER TOOLS (AIR OR ELECTRIC) AND HAMMERS

WARNING:

Always observe the following items for preventing accidental activation.
• When working near the Air Bag Diagnosis Sensor Unit or other Air Bag System sensors with the

ignition ON or engine running, never use air or electric power tools or strike near the sensor(s) with
a hammer. Heavy vibration could activate the sensor(s) and deploy the air bag(s), possibly causing
serious injury.

• When using air or electric power tools or hammers, always switch the ignition OFF, disconnect the

battery, and wait at least 3 minutes before performing any service.

FOR MEXICO

FOR MEXICO : Precaution for Supplemental Restraint System (SRS) "AIR BAG" and 
"SEAT BELT PRE-TENSIONER"

INFOID:0000000008459800

The Supplemental Restraint System such as “AIR BAG” and “SEAT BELT PRE-TENSIONER”, used along
with a front seat belt, helps to reduce the risk or severity of injury to the driver and front passenger for certain
types of collision. Information necessary to service the system safely is included in the “SRS AIR BAG” and
“SEAT BELT” of this Service Manual.

WARNING:

Always observe the following items for preventing accidental activation.
• To avoid rendering the SRS inoperative, which could increase the risk of personal injury or death in

the event of a collision that would result in air bag inflation, all maintenance must be performed by
an authorized NISSAN/INFINITI dealer.

• Improper maintenance, including incorrect removal and installation of the SRS, can lead to personal

injury caused by unintentional activation of the system. For removal of Spiral Cable and Air Bag
Module, see “SRS AIR BAG”.

• Never use electrical test equipment on any circuit related to the SRS unless instructed to in this Ser-

vice Manual. SRS wiring harnesses can be identified by yellow and/or orange harnesses or harness
connectors.

PRECAUTIONS WHEN USING POWER TOOLS (AIR OR ELECTRIC) AND HAMMERS

WARNING:

Revision: 2012 September

2013 MURANO

PWO

PRECAUTIONS

PWO-5

< PRECAUTION >

C

D

E

F

G

H

I

J

K

L

B

A

O

P

N

Always observe the following items for preventing accidental activation.
• When working near the Air Bag Diagnosis Sensor Unit or other Air Bag System sensors with the

ignition ON or engine running, never use air or electric power tools or strike near the sensor(s) with
a hammer. Heavy vibration could activate the sensor(s) and deploy the air bag(s), possibly causing
serious injury.

• When using air or electric power tools or hammers, always switch the ignition OFF, disconnect the

battery, and wait at least 3 minutes before performing any service.

Revision: 2012 September

2013 MURANO

PWO-6

< REMOVAL AND INSTALLATION >

CIGARETTE LIGHTER

REMOVAL AND INSTALLATION

CIGARETTE LIGHTER

Exploded View

INFOID:0000000008459801

Removal and Installation

INFOID:0000000008459802

REMOVAL

1.

Remove console finisher assembly. Refer to 

IP-20, "Exploded View"

.

2.

Pull out cigarette lighter (1).

3.

Disconnect cigarette lighter connector (A).

4.

Pull out cigarette lighter socket (2) by pushing the cigarette
lighter ring pawl (B) from the cigarette lighter socket hole
(square) (C).

5.

Remove cigarette lighter ring (3) from console finisher assembly
while pressing pawls.

INSTALLATION

Install in the reverse order of removal.
NOTE:
Align the cut outs of cigarette lighter socket, cigarette lighter ring, and console finisher assembly.

1

: Cigarette lighter

2

: Cigarette lighter socket

3

: Cigarette lighter ring

JPMIA0784ZZ

D

: Cut out

JPMIA0785ZZ

Revision: 2012 September

2013 MURANO

 

 

 

 

 

 

 

Content      ..     62      63      64      65     ..