Nissan Murano Z51 (2013 year). Manual - part 42

MIR-12

< DTC/CIRCUIT DIAGNOSIS >

[WITH ADP]

DOOR MIRROR REMOTE CONTROL SWITCH

4.

Check continuity between automatic drive positioner control unit harness connector and ground.

Is the inspection result normal?

YES

>> Replace automatic drive positioner control unit. Refer to 

ADP-182, "Removal and Installation"

.

NO

>> Repair or replace harness.

3.

CHECK DOOR MIRROR REMOTE CONTROL SWITCH GROUND CIRCUIT

1.

Turn ignition switch OFF.

2.

Check continuity between door mirror remote control switch harness connector and ground.

Is the inspection result normal?

YES

>> GO TO 4.

NO

>> Repair or replace harness.

4.

CHECK MIRROR SWITCH

Check door mirror remote control switch (mirror switch).
Refer to 

MIR-12, "MIRROR SWITCH : Component Inspection"

.

Is the inspection result normal?

YES

>> GO TO 5.

NO

>> Replace door mirror remote control switch (mirror switch). Refer to 

MIR-49, "Removal and Instal-

lation"

.

5.

CHECK INTERMITTENT INCIDENT

Check intermittent incident.
Refer to 

GI-45, "Intermittent Incident"

.

>> INSPECTION END

MIRROR SWITCH : Component Inspection

INFOID:0000000008455766

1.

CHECK MIRROR SWITCH

1.

Turn ignition switch OFF.

2.

Disconnect door mirror remote control switch connector.

3.

Check continuity between door mirror remote control switch terminals.

Automatic drive positioner control unit Door 

mirror 

remote control switch 

Continuity 

Connector

Terminal

Connector

Terminal

M75

3

D14

15

Existed

4

13

15

12

16

4

Automatic drive positioner control unit 

Ground

Continuity 

Connector

Terminal

M75

3

Not existed

4

15

16

Door mirror remote control switch

Ground

Continuity

 Connector

Terminal

D14

7

Existed

Revision: 2012 September

2013 MURANO

DOOR MIRROR REMOTE CONTROL SWITCH

MIR-13

< DTC/CIRCUIT DIAGNOSIS >

[WITH ADP]

C

D

E

F

G

H

I

J

K

M

A

B

MIR

N

O

P

Is the inspection result normal?

YES

>> INSPECTION END

NO

>> Replace door mirror remote control switch. Refer to 

MIR-49, "Removal and Installation"

.

CHANGEOVER SWITCH

CHANGEOVER SWITCH : Description

INFOID:0000000008455767

Changeover switch is integrated into door mirror remote control switch.
Changeover switch has three positions (L, N and R).
It changes door mirror motor operation by transmitting control signal to automatic drive positioner control unit.

CHANGEOVER SWITCH : Component Function Check

INFOID:0000000008455768

1.

CHECK CHANGEOVER SWITCH FUNCTION

Check the operation on “MIR CHNG SW-R” or “MIR CHNG SW-L” in “DATA MONITOR” mode with CON-
SULT.

Is the inspection result normal?

YES

>> Changeover switch function is OK.

NO

>> Refer to 

MIR-13, "CHANGEOVER SWITCH : Diagnosis Procedure"

.

CHANGEOVER SWITCH : Diagnosis Procedure

INFOID:0000000008455769

1.

CHECK CHANGEOVER SWITCH INPUT SIGNAL

1.

Turn ignition switch OFF.

2.

Disconnect door mirror remote control switch connector.

3.

Turn ignition switch ON.

4.

Check voltage between door mirror remote control switch harness connector and ground.

Is the inspection result normal?

YES

>> GO TO 3.

NO

>> GO TO 2.

2.

CHECK CHANGEOVER SWITCH CIRCUIT

Door mirror remote control switch

Condition

Continuity

Connector

Terminal

D14

4

7

Mirror switch

RIGHT

Existed

Other than above

Not existed

13

LEFT

Existed

Other than above

Not existed

15

UP

Existed

Other than above

Not existed

12

DOWN

Existed

Other than above

Not existed

Monitor item

Condition

MIR CHNG SW-R/L

When operating the changeover toward the right or left side.

: ON

Other than above.

: OFF

(+)

(–)

Voltage (V)

(Approx.)

Door mirror remote control switch

 Connector

Terminal

D14

10

Ground

5

11

Revision: 2012 September

2013 MURANO

MIR-14

< DTC/CIRCUIT DIAGNOSIS >

[WITH ADP]

DOOR MIRROR REMOTE CONTROL SWITCH

1.

Turn ignition switch OFF.

2.

Disconnect automatic drive positioner control unit connector.

3.

Check continuity between automatic drive positioner control unit harness connector and door mirror
remote control switch harness connector.

4.

Check continuity between automatic drive positioner control unit harness connector and ground.

Is the inspection result normal?

YES

>> Replace automatic drive positioner control unit. Refer to 

ADP-182, "Removal and Installation"

 .

NO

>> Repair or replace harness.

3.

CHECK DOOR MIRROR REMOTE CONTROL SWITCH GROUND CIRCUIT

1.

Turn ignition switch OFF.

2.

Check continuity between door mirror remote control switch harness connector and ground.

Is the inspection result normal?

YES

>> GO TO 4.

NO

>> Repair or replace harness.

4.

CHECK CHANGEOVER SWITCH

Check door mirror remote control switch (changeover switch).
Refer to 

MIR-14, "CHANGEOVER SWITCH : Component Inspection"

.

Is the inspection result normal?

YES

>> GO TO 5.

NO

>> Replace door mirror remote control switch (changeover switch). Refer to 

MIR-49, "Removal and

Installation"

.

5.

CHECK INTERMITTENT INCIDENT

Check intermittent incident.
Refer to 

GI-45, "Intermittent Incident"

.

>> INSPECTION END

CHANGEOVER SWITCH : Component Inspection

INFOID:0000000008455770

1.

CHECK CHANGEOVER SWITCH 

1.

Turn ignition switch OFF.

2.

Disconnect door mirror remote control switch connector.

3.

Check continuity between door mirror remote control switch terminals.

Automatic drive positioner control unit Door 

mirror 

remote control switch

Continuity

Connector

Terminal

Connector

Terminal

M75

2

D14

11

Existed

14

10

Automatic drive positioner control unit 

Ground

Continuity

Connector

Terminal

M75

2

Not existed

14

Door mirror remote control switch 

Ground

Continuity

Connector

Terminal

D14

7

Existed

Revision: 2012 September

2013 MURANO

DOOR MIRROR REMOTE CONTROL SWITCH

MIR-15

< DTC/CIRCUIT DIAGNOSIS >

[WITH ADP]

C

D

E

F

G

H

I

J

K

M

A

B

MIR

N

O

P

Is the inspection result normal?

YES

>> INSPECTION END

NO

>> Replace door mirror remote control switch. Refer to 

MIR-49, "Removal and Installation"

.

Door mirror remote control switch

Condition

Continuity

Connector

Terminal

D14

10

7

Changeover switch

LEFT

Existed

Other than above

Not existed

11

RIGHT

Existed

Other than above

Not existed

Revision: 2012 September

2013 MURANO

MIR-16

< DTC/CIRCUIT DIAGNOSIS >

[WITH ADP]

DOOR MIRROR

DOOR MIRROR

Wiring Diagram - DOOR MIRROR SYSTEM (WITH AUTOMATIC DRIVE POSITION-
ER) -

INFOID:0000000008455771

For connector terminal arrangements, harness layouts, and alphabets in a

(option abbreviation; if not

described in wiring diagram), refer to 

GI-12, "Connector Information"

.

JCLWM2736GB

Revision: 2012 September

2013 MURANO

AUTO ANTI-DAZZLING INSIDE MIRROR SYSTEM

MIR-17

< DTC/CIRCUIT DIAGNOSIS >

[WITH ADP]

C

D

E

F

G

H

I

J

K

M

A

B

MIR

N

O

P

AUTO ANTI-DAZZLING INSIDE MIRROR SYSTEM

Wiring Diagram - INSIDE MIRROR SYSTEM -

INFOID:0000000008455772

For connector terminal arrangements, harness layouts, and alphabets in a

(option abbreviation; if not

described in wiring diagram), refer to 

GI-12, "Connector Information"

.

JCLWM6099GB

Revision: 2012 September

2013 MURANO

MIR-18

< ECU DIAGNOSIS INFORMATION >

[WITH ADP]

DRIVER SEAT CONTROL UNIT

ECU DIAGNOSIS INFORMATION

DRIVER SEAT CONTROL UNIT

Reference Value

INFOID:0000000008840910

VALUES ON THE DIAGNOSIS TOOL

NOTE:
The following table includes information (items) inapplicable to this vehicle. For information (items) applicable
to this vehicle, refer to CONSULT display items.

CONSULT MONITOR ITEM

Monitor Item

Condition

Value/Status

SET SW

Set switch

Push

ON

Release

OFF

MEMORY SW1

Memory switch 1

Push

ON

Release

OFF

MEMORY SW2

Memory switch 2

Push

ON

Release

OFF

SLIDE SW–FR

Sliding switch (forward)

Operate

ON

Release

OFF

SLIDE SW–RR

Sliding switch (backward)

Operate

ON

Release

OFF

RECLN SW–FR

Reclining switch (forward)

Operate

ON

Release

OFF

RECLN SW–RR

Reclining switch (back-
ward)

Operate

ON

Release

OFF

LIFT FR SW–UP

Lifting switch front (up)

Operate

ON

Release

OFF

LIFT FR SW–DN

Lifting switch front (down)

Operate

ON

Release

OFF

LIFT RR SW–UP

Lifting switch rear (up)

Operate

ON

Release

OFF

LIFT RR SW–DN

Lifting switch rear (down)

Operate

ON

Release

OFF

MIR CON SW–UP

Mirror switch

Up

ON

Other than above

OFF

MIR CON SW–DN

Mirror switch

Down

ON

Other than above

OFF

MIR CON SW–RH

Mirror switch

Right

ON

Other than above

OFF

MIR CON SW–LH

Mirror switch

Left

ON

Other than above

OFF

MIR CHNG SW–R

Changeover switch

Right

ON

Other than above

OFF

MIR CHNG SW–L

Changeover switch

Left

ON

Other than above

OFF

Revision: 2012 September

2013 MURANO

DRIVER SEAT CONTROL UNIT

MIR-19

< ECU DIAGNOSIS INFORMATION >

[WITH ADP]

C

D

E

F

G

H

I

J

K

M

A

B

MIR

N

O

P

TILT SW-UP

Tilt switch

Upward

ON

Other than above

OFF

TILT SW-DOWN

Tilt switch

Downward

ON

Other than above

OFF

TELESCO SW-FR

Telescopic switch

Forward

ON

Other than above

OFF

TELESCO SW-RR

 Telescopic switch

Backward

ON

Other than above

OFF

DETENT SW

Selector lever

P position

OFF

Other than above

ON

STARTER SW

Ignition position

Cranking

ON

Other than above

OFF

SLIDE PULSE

Seat sliding

Forward

The numeral value decreases *

Backward

The numeral value increases*

Other than above

No change to numeral value*

RECLN PULSE

Seat reclining

Forward

The numeral value decreases*

Backward

The numeral value increases 

*

Other than above

No change to numeral value

*

LIFT FR PULSE

Seat lifter (front)

Up

The numeral value decreases 

*

Down

The numeral value increases 

*

Other than above

No change to numeral value

*

LIFT RR PULSE

Seat lifter (rear)

Up

The numeral value decreases 

*

Down

The numeral value increases 

*

Other than above

No change to numeral value

*

MIR/SEN RH U–D

Door mirror (passenger side)

Change between 3.4 (close to peak)

0.6 (close to valley)

MIR/SEN RH R–L

Door mirror (passenger side)

Change between 3.4 (close to left edge)

0.6 (close to right edge)

MIR/SEN LH U–D

Door mirror (driver side)

Change between 3.4 (close to peak)

0.6 (close to valley)

MIR/SEN LH R–L

Door mirror (driver side)

Change between 0.6 (close to left edge)

3.4 (close to right edge)

TILT PULSE

Tilt position

Upward

The numeral value decreases 

*

Downward

The numeral value increases 

*

Other than above

No change to numeral value

*

TELESCO PULSE

Telescopic position

Forward

The numeral value decreases 

*

Backward

The numeral value increases 

*

Other than above

No change to numeral value

*

STEERING STATUS

NOTE:
This item is displayed, but cannot be monitored

VEHICLE SPEED

The condition of vehicle speed is displayed

km/h

P RANG SW CAN

Selector lever

P position

ON

Other than above

OFF

Monitor Item

Condition

Value/Status

Revision: 2012 September

2013 MURANO

MIR-20

< ECU DIAGNOSIS INFORMATION >

[WITH ADP]

DRIVER SEAT CONTROL UNIT

*

: The value at the position attained when the battery is connected is regarded as 32768.

TERMINAL LAYOUT

PHYSICAL VALUES

R RANGE (CAN)

Selector lever

R position

ON

Other than above

OFF

DOOR SW-FL

Driver door

Open

ON

Close

OFF

DOOR SW-FR

Passenger door

Open

ON

Close

OFF

IGN ON SW

Ignition switch

ON position

ON

Other than above

OFF

ACC ON SW

Ignition switch

ACC or ON position

ON

Other than above

OFF

KEY ON SW

Intelligent Key

Inserted is key slot

ON

Inserted is not key slot

OFF

KEYLESS ID

UNLOCK button of Intelligent Key is pressed

1,2,3,4or5

KYLS DR UNLK

Intelligent Key or driver 
side door request switch

ON

ON

OFF

OFF

VHCL SPEED (ABS)

Can signal from ABS

Received

ON

Not received

OFF

HANDLE

The BCM for handle position is displayed

LHD

RHD

TRANSMISSION

Transmission type is displayed

AT or CVT

MT

Monitor Item

Condition

Value/Status

JMJIA1689ZZ

Terminal No.

(wire color)

Description

Condition

Voltage (V)

(Approx)

+

-

Signal name

Input/

Output

1

(R)

Ground

Power source 

Input

—

Battery voltage

2

(B)

Ground

Ground (power)

—

—

0

3

(G)

Ground

Sliding motor backward 
output signal

Output

Seat sliding

Operate

(backward)

Battery voltage

Stop

0

Revision: 2012 September

2013 MURANO

DRIVER SEAT CONTROL UNIT

MIR-21

< ECU DIAGNOSIS INFORMATION >

[WITH ADP]

C

D

E

F

G

H

I

J

K

M

A

B

MIR

N

O

P

4

(G/R)

Ground

Sliding motor forward out-
put signal

Output

Seat sliding

Operate

 (forward)

Battery voltage

Release

0

5

(V)

Ground

Reclining motor backward 
output signal

Output

Seat reclining 

Operate

(backward)

Battery voltage

Stop

0

6

(R/L)

Ground

Reclining motor forward 
output signal

Output

Seat reclining

Operate

 (forward)

Battery voltage

Release

0

7

(L)

Ground

Lifting motor (rear) down 
output signal

Output

Seat lifting (rear)

Operate

(down)

Battery voltage

Stop

0

8

(L/W)

Ground

Lifting motor (rear) up out-
put signal

Output

Seat lifting (rear)

Operate

(up)

Battery voltage

Stop

0 

9

(L/R)

Ground

Lifting motor (front) down 
output signal

Output

Seat lifting (front)

Operate

(down)

Battery voltage

Stop

0

10

(L/B)

Ground

Lifting motor (front) up out-
put signal

Output

Seat lifting (front)

Operate

(up)

Battery voltage

Stop

 0 

11

(G/B)

Ground

Sliding switch backward 
signal

Input

Sliding switch

Operate

(backward)

0

Release

Battery voltage

12

(G/W)

Ground

Sliding switch forward sig-
nal

Input

Sliding switch

Operate

 (forward)

0

Release

Battery voltage

13

(R/G)

Ground

Reclining switch backward 
signal

Input

Reclining switch

Operate

(backward)

0

Release

Battery voltage

14

(R/W)

Ground

Reclining switch forward 
signal

Input

Reclining switch

Operate

 (forward)

0

Release

Battery voltage

15

(Y/B)

Ground

Lifting switch (rear) down 
signal

Input

Lifting switch 

(rear)

Operate

(down)

0

Release

Battery voltage

16

(Y/R)

Ground

Lifting switch (rear) up sig-
nal

Input

Seat lifting switch 

(rear)

Operate

 (up)

0

Release

Battery voltage

17

(LG/B)

Ground

Lifting switch (front) down 
signal

Input

Lifting switch 

(front)

Operate

(down)

0

Release

Battery voltage

18

(LG/R)

Ground

Lifting switch (front) up sig-
nal

Input

Seat lifting switch 

(front)

Operate

 (up)

0

Release

Battery voltage

Terminal No.

(wire color)

Description

Condition

Voltage (V)

(Approx)

+

-

Signal name

Input/

Output

Revision: 2012 September

2013 MURANO

MIR-22

< ECU DIAGNOSIS INFORMATION >

[WITH ADP]

DRIVER SEAT CONTROL UNIT

19

(G/Y)

Ground

Sliding sensor signal

Input

Seat sliding

Operate

Stop

0 or 5

20

(R/Y)

Ground

Reclining sensor signal

Input

Seat reclining

Operate

Stop

0 or 5

21

(L/Y)

Ground

Lifting sensor (rear) signal

Input

Seat lifting (rear)

Operate

Stop

0 or 5

22

(BR/Y)

Ground

Lifting sensor (front) signal

Input

Seat lifting (front)

Operate

Stop

0 or 5

23

(P)

—

CAN-H

—

—

—

24

(P/L)

—

CAN-L

—

—

—

25

(G/O)

Ground

Memory indictor 1 signal

Output

Memory indictor 1

Illuminate

1

Other than above

Battery voltage

26

(L/O)

Ground

Memory indictor 2 signal

Output

Memory indictor 2

Illuminate

1

Other than above

Battery voltage

27

(V)

Ground

Memory switch 1 signal

Input

Memory switch 1

Press

0

Other than above

5

28

(V/W)

Ground

Memory switch 2 signal

Input

Memory switch 2

Press

0

Other than above

5

29

(O/L)

Ground

Set switch signal

Input

Set switch

Press

0

Other than above

5

Terminal No.

(wire color)

Description

Condition

Voltage (V)

(Approx)

+

-

Signal name

Input/

Output

JMJIA0119ZZ

JMJIA0119ZZ

JMJIA0119ZZ

JMJIA0119ZZ

Revision: 2012 September

2013 MURANO

DRIVER SEAT CONTROL UNIT

MIR-23

< ECU DIAGNOSIS INFORMATION >

[WITH ADP]

C

D

E

F

G

H

I

J

K

M

A

B

MIR

N

O

P

30

(BR)

Ground

Tilt sensor signal

Input

Tilt

Operate

Other than above

0 or 5

31

(BR/W)

Ground

Telescopic sensor signal

Input

Telescopic

Operate

Other than above

0 or 5

32

(W/L)

Ground

UART communication 
(TX/RX)

Input

Ignition switch ON

33

(W)

Ground

Sensor power supply

Output

—

Battery voltage

Terminal No.

(wire color)

Description

Condition

Voltage (V)

(Approx)

+

-

Signal name

Input/

Output

JMJIA0119ZZ

JMJIA1391ZZ

Revision: 2012 September

2013 MURANO

MIR-24

< ECU DIAGNOSIS INFORMATION >

[WITH ADP]

DRIVER SEAT CONTROL UNIT

Wiring Diagram - AUTOMATIC DRIVE POSITIONER CONTROL SYSTEM -

INFOID:0000000008840911

For connector terminal arrangements, harness layouts, and alphabets in a

(option abbreviation; if not

described in wiring diagram), refer to 

GI-12, "Connector Information"

.

JRJWC0297GB

Revision: 2012 September

2013 MURANO

DRIVER SEAT CONTROL UNIT

MIR-25

< ECU DIAGNOSIS INFORMATION >

[WITH ADP]

C

D

E

F

G

H

I

J

K

M

A

B

MIR

N

O

P

JRJWC0298GB

Revision: 2012 September

2013 MURANO

MIR-26

< ECU DIAGNOSIS INFORMATION >

[WITH ADP]

DRIVER SEAT CONTROL UNIT

Fail Safe

INFOID:0000000008840912

The fail-safe mode may be activated if the following symptoms are observed.

JRJWC0299GB

Revision: 2012 September

2013 MURANO

DRIVER SEAT CONTROL UNIT

MIR-27

< ECU DIAGNOSIS INFORMATION >

[WITH ADP]

C

D

E

F

G

H

I

J

K

M

A

B

MIR

N

O

P

DTC Index

INFOID:0000000008840913

*1

:

• 0: Current malfunction is present

• 1-39: Displayed if any previous malfunction is present when current condition is normal. The numeral value increases by one at each

IGN ON to OFF cycle from 1 to 39. The counter remains at 39 even if the number of cycles exceeds it. However, the counter is reset
to 1 if any malfunction is detected again, the normal operation is resumed and the ignition switch is turned from OFF to ON. 

Operating in

fail-safe mode

Malfunction Item

Related 

DTC

Diagnosis

Only manual functions operate normally.

CAN communication

U1000

ADP-44

CONTROL UNIT

U1010

ADP-45

EEPROM

B2130

ADP-46

Only manual functions, except door mirror, operate normally.

UART communication

B2128

ADP-53

Only manual functions, except seat sliding, operate normally.

Seat sliding output

B2112

ADP-47

Only manual functions, except seat reclining, operate normally.

Seat reclining output

B2113

ADP-49

Only manual functions, except steering tilt, operate normally.

Steering column tilt output

B2116

ADP-51

CONSULT

display

Timing

*1

Item

Reference page

Current mal-

function

Previous mal-

function

CAN COMM CIRCUIT
[U1000]

0

1-39

CAN communication

ADP-44

CONTROL UNIT
[U1010]

0

1-39

Control unit

ADP-45

SEAT SLIDE
[B2112]

0

1-39

Seat slide motor output

ADP-47

SEAT RECLINING
[B2113]

0

1-39

Seat reclining motor output

ADP-49

STEERING TILT
[B2116]

0

1-39

Tilt motor output

ADP-51

UART COMM
[B2128]

0

1-39

UART communication

ADP-53

EEPROM
[B2130]

0

1-39

EEPROM

ADP-46

Revision: 2012 September

2013 MURANO