Nissan Murano Z51 (2011 year). Manual - part 62

ID REGISTRATION

WT-21

< BASIC INSPECTION >

C

D

F

G

H

I

J

K

L

M

A

B

WT

N

O

P

ID REGISTRATION 

Description

INFOID:0000000006598668

This procedure must be done after replacing or rotating wheels, replacing transmitter or BCM.

Work Procedure

INFOID:0000000006598669

1.

TRANSMITTER ID REGISTRATION PROCEDURE

With CONSULT-III.

1.

Display the “WORK SUPPORT” screen and select “ID REGIST”.

Is the transmitter activation tool (J-45295) used for the transmitter ID registration procedure?

YES

>> GO TO 2.

NO

>> GO TO 3.

2.

TRANSMITTER ID REGISTRATION PROCEDURE (WITH TRANSMITTER ACTIVATION TOOL)

1.

Turn the ignition switch ON.

2.

Select the start button on the “ID REGIST” screen.

3.

Contact the transmitter activation tool (J-45295) (1) to the side of
the tire at the location to the transmitter.

4.

Press and hold the activation tool button while pushing the tool
to the tire surface. (approximately for 5 seconds)

CAUTION:

Perform the ID registration procedure starting from the
vehicle front left wheel, then repeat the procedure in the
order of the front right wheel, rear right wheel, and rear left
wheel.

5.

When ID registration is completed, check the following pattern at each wheel.

6.

After the ID registration procedure for all wheels is completed, press “END” to end ID registration, and
check that ID registration for all wheels is completed.

Is the check result normal?

YES

>> ID registration END.

NO

>> Performs trouble-diagnosis of the Tire Pressure Monitoring System (TPMS). Refer to 

BCS-78,

"DTC Index"

. 

3.

TRANSMITTER ID REGISTRATION PROCEDURE (WITHOUT TRANSMITTER ACTIVATION TOOL) 

1.

Adjust the tire pressure for all wheels to match the list below.

NNEIC0020ZZ

Se-

quence

ID registration position

Turn signal lamp

CONSULT-III

1

Front left wheel

2 blinks

“Red”

↓

“Green”

2

Front right wheel

3

Rear right wheel

4

Rear left wheel

Tire position

Tire pressure kPa (kg/cm

2

, psi)

Front LH

240 (2.4, 35)

Front RH

220 (2.2, 31)

Rear RH

200 (2.0, 29)

Rear LH

180 (1.8, 26)

Revision: 2011 November

2011 MURANO

WT-22

< BASIC INSPECTION >

ID REGISTRATION

2.

Drive the vehicle at a speed at more than 40 km/h (25 MPH) for 3 minutes or more, then perform the
transmitter ID registration procedure.

3.

After ID registration for all wheels is completed, press “END” to end ID registration.

4.

Adjust the tire pressures for all wheels to the specified value. Refer to 

WT-52, "Tire Air Pressure"

. 

Is ID registrations for all wheels completed?

YES

>> ID registration END.

NO

>> Performs trouble-diagnosis of the Tire Pressure Monitoring System (TPMS). Refer to 

BCS-78,

"DTC Index"

. 

ID registration position

CONSULT-III

Front LH

“Red”

↓

“Green”

Front RH

Rear RH

Rear LH

Revision: 2011 November

2011 MURANO

C1704, C1705, C1706, C1707 LOW TIRE PRESSURE

WT-23

< DTC/CIRCUIT DIAGNOSIS >

C

D

F

G

H

I

J

K

L

M

A

B

WT

N

O

P

DTC/CIRCUIT DIAGNOSIS

C1704, C1705, C1706, C1707 LOW TIRE PRESSURE

Description

INFOID:0000000006260288

When the tire pressure monitoring system detects low inflation pressure, the low tire pressure warning lamps
in the combination meter comes on.

DTC Logic

INFOID:0000000006260289

DTC DETECTION LOGIC

NOTE:

182.7 kPa (1.9 kg/cm

2

, 26 psi): Standard air pressure is for 230 kPa (2.3 kg/cm

2

,33 psi) vehicles.

DTC CONFIRMATION PROCEDURE

1.

DTC REPRODUCTION PROCEDURE 

With CONSULT-III

1.

Turn the ignition switch ON.

CAUTION:

Never start the engine.

2.

Check the tire pressure for all wheels and adjust to the specified value. Refer to 

WT-52, "Tire Air Pres-

sure"

. 

3.

Perform “SELF-DIAG RESULTS” in “AIR PRESSURE MONITOR” of “BCM”.

Is DTC “C1704”, “C1705”, “C1706”, “C1707” detected?

YES

>> Perform trouble diagnosis. Refer to 

WT-23, "Diagnosis Procedure"

.

NO

>> INSPECTION END

Diagnosis Procedure

INFOID:0000000006260290

1.

CHECK TIRE PRESSURE

Check the internal pressure of all wheels. Refer to 

WT-52, "Tire Air Pressure"

. 

Is the inspection result normal?

YES

>> Replace the DTC-detected malfunctioning transmitter. Refer to 

WT-49, "Exploded View"

.

NO

>> After adjusting the air pressure, GO TO 2.

2.

CHECK TIRE PRESSURE SIGNAL

With CONSULT-III

1.

Drive for 3 minutes at a speed of 40 km/h (25 MPH) or more, then drive normally for 10 minutes.

2.

Perform “DATA MONITOR” in “AIR PRESSURE MONITOR” of “BCM”.

3.

Select “BCM” in “DATA MONITOR”, and check that the tire pressures match the standard value.

DTC

Display item

Malfunction detected condition

Possible cause

C1704

LOW PRESSURE FL

Front LH tire pressure drops to * kPa (* kg/cm

2

, * psi) or less. [NOTE]

• Low tire pressure
• Transmitter mal-

function

C1705

LOW PRESSURE FR

Front RH tire pressure drops to * kPa (* kg/cm

2

, * psi) or less. [NOTE]

C1706

LOW PRESSURE RR

Rear RH tire pressure drops to * kPa (* kg/cm

2

, * psi) or less. [NOTE]

C1707

LOW PRESSURE RL

Rear LH tire pressure drops to * kPa (* kg/cm

2

, * psi) or less. [NOTE]

Monitor item

Condition

Displayed value

AIR PRESS FL

Drive for 3 minutes at a speed of 40 km/h (25 MPH) or 
more, then drive normally for 10 minutes.

Internal pressure of tires

AIR PRESS FR

AIR PRESS RR

AIR PRESS RL

Revision: 2011 November

2011 MURANO

WT-24

< DTC/CIRCUIT DIAGNOSIS >

C1704, C1705, C1706, C1707 LOW TIRE PRESSURE

CAUTION:

Stop the vehicle and within 5 minutes, use “DATA MONITOR” in “AIR PRESSURE MONITOR” of “BCM”
to display the tire pressure for all wheels.

Is the inspection result normal?

YES

>> Inspect or repair the tires or wheels and adjust the tire pressure to the specification.

NO

>> GO TO 1.

Revision: 2011 November

2011 MURANO

C1708, C1709, C1710, C1711 TRANSMITTER

WT-25

< DTC/CIRCUIT DIAGNOSIS >

C

D

F

G

H

I

J

K

L

M

A

B

WT

N

O

P

C1708, C1709, C1710, C1711 TRANSMITTER

DTC Logic

INFOID:0000000006260292

DTC DETECTION LOGIC

DTC CONFIRMATION PROCEDURE

1.

DTC REPRODUCTION PROCEDURE

With CONSULT-III

1.

Drive for 3 minutes at a speed of 40 km/h (25 MPH) or more, then drive normally for 10 minutes.

2.

Perform “SELF-DIAG RESULTS” in “AIR PRESSURE MONITOR” of “BCM”.

Is DTC “C1708”, “C1709”, “C1710”, “C1711” detected?

YES

>> Perform trouble diagnosis. Refer to 

WT-25, "Diagnosis Procedure"

.

NO

>> INSPECTION END

Diagnosis Procedure

INFOID:0000000006260293

1.

CHECK TIRE PRESSURE SIGNAL

With CONSULT-III

1.

Drive for 3 minutes at a speed of 40 km/h (25 MPH) or more, then drive normally for 10 minutes.

2.

Perform “DATA MONITOR” in “AIR PRESSURE MONITOR” of “BCM”.

3.

Select “BCM” in “DATA MONITOR”, and check that the tire pressures match the standard value.

CAUTION:

Stop the vehicle and within 5 minutes, use “DATA MONITOR” in “AIR PRESSURE MONITOR” of “BCM”
to display the tire pressure for all wheels.

Is a tire pressure of 0 kPa (0 Psi) displayed for all wheels?

YES

>> GO TO 2.

NO

>> GO TO 5.

2.

CHECK HARNESS BETWEEN BCM AND TIRE PRESSURE RECEIVER

1.

Turn the ignition switch OFF.

2.

Disconnect BCM harness connector and tire pressure receiver harness connector.

3.

Check the continuity between BCM harness connector and tire pressure receiver harness connector.

DTC

Display item

Malfunction detected condition

Possible cause

C1708

[NO DATA] FL

Tire pressure data signal from the front left wheel 
transmitter cannot be detected.

• Harness or connector

(Tire pressure receiver, BCM)

• ID registration is not finished
• Transmitter malfunction
• BCM malfunction

C1709

[NO DATA] FR

Tire pressure data signal from the front right wheel 
transmitter cannot be detected.

C1710

[NO DATA] RR

Tire pressure data signal from the rear right wheel 
transmitter cannot be detected.

C1711

[NO DATA] RL

Tire pressure data signal from the rear left wheel 
transmitter cannot be detected.

Monitor item

Condition

Displayed value

AIR PRESS FL

Drive for 3 minutes at a speed of 40 km/h (25 MPH) or 
more, then drive normally for 10 minutes.

Internal pressure of tires

AIR PRESS FR

AIR PRESS RR

AIR PRESS RL

Revision: 2011 November

2011 MURANO

WT-26

< DTC/CIRCUIT DIAGNOSIS >

C1708, C1709, C1710, C1711 TRANSMITTER

4.

Check the continuity between BCM harness connector and ground.

Is the inspection result normal?

YES

>> GO TO 3.

NO

>> Repair or replace damaged parts.

3.

CHECK TIRE PRESSURE RECEIVER POWER SUPPLY CIRCUIT 

1.

Connect the BCM harness connector.

2.

Turn the ignition switch ON.

CAUTION:

Never start the engine.

3.

Check the voltage between the BCM harness connector and ground.

Is the inspection result normal?

YES

>> GO TO 4.

NO

>> Repair or replace damaged parts.

4.

CHECK TIRE PRESSURE RECEIVER

Check tire pressure receiver. Refer to 

WT-32, "Diagnosis Procedure"

.

Is the inspection result normal?

YES

>> GO TO 5.

NO

>> Replace tire pressure receiver. Refer to 

WT-51, "Removal and Installation"

.

5.

CHECK ID REGISTRATION

Perform ID registration of all transmitters. Refer to 

WT-21, "Work Procedure"

.

Can ID registration of all transmitters be completed?

YES

>> GO TO 6.

NO

>> Replace transmitter. Refer to 

WT-49, "Exploded View"

.

6.

CHECK TIRE PRESSURE MONITORING SYSTEM

With CONSULT-III

1.

Drive at a speed of 40 km/h (25 MPH) or more for several minutes without stopping.

2.

Perform “DATA MONITOR” in “AIR PRESSURE MONITOR” of “BCM”.

3.

Select “BCM” in “DATA MONITOR”, and check that the tire pressures match the standard value.

BCM

Tire pressure receiver

Continuity

Connector

Terminal

Connector

Terminal

M123

137

M21

1

Existed

138

4

139

2

BCM

—

Continuity

Connector

Terminal

M123

137

Ground

Not existed

138

139

BCM

—

Voltage

(Approx.)

Connector

Terminal

M123

138

Ground

5 V

Revision: 2011 November

2011 MURANO

C1708, C1709, C1710, C1711 TRANSMITTER

WT-27

< DTC/CIRCUIT DIAGNOSIS >

C

D

F

G

H

I

J

K

L

M

A

B

WT

N

O

P

CAUTION:

Stop the vehicle and within 15 minutes, use “DATA MONITOR” in “AIR PRESSURE MONITOR” of
“BCM”   to read the tire pressure for all wheels.
Is the inspection result normal?

YES

>> Replace the DTC-detected malfunctioning transmitter. Refer to 

WT-49, "Exploded View"

.

NO

>> Replace BCM. Refer to 

BCS-85, "Exploded View"

.

Monitor item

Condition

Displayed value

AIR PRESS FL

Drive at a speed of 40 km/h (25 MPH) or more, for several 
minutes without stopping.

Internal pressure of tires

AIR PRESS FR

AIR PRESS RR

AIR PRESS RL

Revision: 2011 November

2011 MURANO

WT-28

< DTC/CIRCUIT DIAGNOSIS >

C1716, C1717, C1718, C1719 TRANSMITTER

C1716, C1717, C1718, C1719 TRANSMITTER

DTC Logic

INFOID:0000000006260295

DTC DETECTION LOGIC

DTC CONFIRMATION PROCEDURE

1.

DTC REPRODUCTION PROCEDURE

With CONSULT-III

1.

Turn the ignition switch ON.

CAUTION:

Never start the engine.

2.

Check the tire pressure for all wheels and adjust to the specified value. Refer to 

WT-52, "Tire Air Pres-

sure"

. 

3.

Perform “SELF-DIAG RESULTS” in “AIR PRESSURE MONITOR” of “BCM”.

Is DTC “C1716”, “C1717”, “C1718”, “C1719” detected?

YES

>> Perform trouble diagnosis. Refer to 

WT-28, "Diagnosis Procedure"

.

NO

>> INSPECTION END

Diagnosis Procedure

INFOID:0000000006260296

1.

CHECK TIRE PRESSURE

Check the internal pressure of all wheels. Refer to 

WT-52, "Tire Air Pressure"

. 

Is the inspection result normal?

YES

>> Replace the DTC-detected malfunctioning transmitter. Refer to 

WT-49, "Exploded View"

.

NO

>> After adjusting the tire pressure, GO TO 2.

2.

CHECK TIRE PRESSURE SIGNAL

With CONSULT-III

1.

Check and adjust the tire pressure for all wheels. Refer to 

WT-52, "Tire Air Pressure"

. 

2.

Perform transmitter ID registration for all wheels. Refer to 

WT-21, "Work Procedure"

. 

3.

Drive for 3 minutes at a speed of 40 km/h (25 MPH) or more, then drive normally for 10 minutes.

4.

Perform “DATA MONITOR” in “AIR PRESSURE MONITOR” of “BCM”.

5.

Select “BCM” in “DATA MONITOR”, and check that the tire pressures match the standard value.

CAUTION:

Stop the vehicle and within 15 minutes, use CONSULT-III “DATA MONITOR” to display the tire
pressure for all wheels.

6.

Check that “DATA MONITOR” displays tire pressure of 438.60 kPa (4.47 kg/cm

2

, 63.60 Psi).

Is the inspection 438.60 kPa (4.47 kg/cm

2

, 63.60 Psi)?

YES

>> Replace transmitter the tire pressure 438.60 kPa (4.386 bar, 4.47 kg/cm

2

, 63.60 Psi) displayed.

Refer to 

WT-49, "Exploded View"

.

NO

>> GO TO 1.

DTC

Display item

Malfunction detected condition

Possible case

C1716

[PRESSDATA ERR] FL

Malfunction in the tire pressure data from the front left 
wheel transmitter.

• ID registration is not fin-

ished

• Transmitter malfunction

C1717

[PRESSDATA ERR] FR

Malfunction in the tire pressure data from the front right 
wheel transmitter.

C1718

[PRESSDATA ERR] RR

Malfunction in the tire pressure data from the rear right 
wheel transmitter.

C1719

[PRESSDATA ERR] RL

Malfunction in the tire pressure data from the rear left 
wheel transmitter.

Revision: 2011 November

2011 MURANO

C1729 VEHICLE SPEED SIGNAL

WT-29

< DTC/CIRCUIT DIAGNOSIS >

C

D

F

G

H

I

J

K

L

M

A

B

WT

N

O

P

C1729 VEHICLE SPEED SIGNAL

Description

INFOID:0000000006260298

BCM detects no vehicle speed signal.

DTC Logic

INFOID:0000000006260299

DTC DETECTION LOGIC

DTC CONFIRMATION PROCEDURE

1.

DTC REPRODUCTION PROCEDURE

With CONSULT-III

1.

Drive for several minutes at a speed of 40 km/h (25 MPH) or more, then stop the vehicle.

2.

Perform “SELF-DIAG RESULTS” in “AIR PRESSURE MONITOR” of “BCM”.

Is DTC “C1729” detected?

YES

>> Perform trouble diagnosis. Refer to 

WT-29, "Diagnosis Procedure"

.

NO

>> INSPECTION END

Diagnosis Procedure

INFOID:0000000006260300

1.

PERFORM COMBINATION METER SELF-DIAGNOSIS

With CONSULT-III

Perform “SELF-DIAG RESULTS” of “METER/M&A”.

Is any DTC detected?

YES

>> Check the DTC. Refer to 

MWI-77, "DTC Index"

.

NO

>> GO TO 2.

2.

PERFORM SELF-DIAGNOSIS

With CONSULT-III

Perform “SELF-DIAG RESULTS” in “AIR PRESSURE MONITOR” of “BCM”.
Is DTC “C1729” detected?

YES

>> Replace BCM. Refer to 

WT-9, "COMMON ITEM : CONSULT-III Function (BCM - COMMON

ITEM)"

.

NO

>> GO TO 3.

3.

CHECK INFORMATION

With CONSULT-III

1.

Perform “DATA MONITOR” in “AIR PRESSURE MONITOR” of “BCM”.

2.

Select “BCM” in “DATA MONITOR”, and check the input/output values. Refer to 

BCS-47, "Reference

Value"

. 

Is the inspection result normal?

YES

>> Check pin terminal and connection of each harness connector for malfunctioning conditions. 

NO

>> Replace BCM. Refer to 

BCS-85, "Exploded View"

. 

DTC 

number

Trouble diagnosis name

DTC detecting condition

Possible case

C1729

VHCL SPEED SIG ERR

Vehicle speed signal not detected.

• CAN communication error
• Combination meter malfunction

Revision: 2011 November

2011 MURANO

WT-30

< DTC/CIRCUIT DIAGNOSIS >

C1734 BCM

C1734 BCM

DTC Logic

INFOID:0000000006260302

DTC DETECTION LOGIC

DTC CONFIRMATION PROCEDURE

1.

DTC REPRODUCTION PROCEDURE

With CONSULT-III

1.

Drive at a speed of 40 km/h (25 MPH) or more for several minutes without stopping.

2.

Perform “SELF-DIAG RESULTS” in “AIR PRESSURE MONITOR” of “BCM”.

CAUTION:

Perform within 15 minutes after stop the vehicle.

Is DTC “C1734” detected?

YES

>> Perform trouble diagnosis. Refer to 

WT-30, "Diagnosis Procedure"

.

NO

>> INSPECTION END

Diagnosis Procedure

INFOID:0000000006260303

1.

CHECK BCM POWER SUPPLY

1.

Turn the ignition switch OFF.

2.

Disconnect BCM harness connector.

3.

Check voltage between BCM harness connector terminals and ground.

Is the power supply normal?

YES

>> GO TO 2.

NO

>>

Check the following. If any items are damaged, repair or replace damage parts.

• 40A fusible link [No. L located in the fuse block]. Refer to 

PG-113, "Fuse and Fusible Link

Arrangement"

.

• 10A fuse [No. 10 located in the fuse block (J/B)]. Refer to 

PG-112, "Fuse, Connector and Termi-

nal Arrangement"

.

• Harness for short or open between battery and BCM harness connector M118 terminal 1.
• Harness for short or open between battery and BCM harness connector M119 terminal 11.
• Check the Battery voltage.

2.

CHECK BCM GROUND

Check the continuity between BCM harness connector and ground.

Is the inspection result normal?

YES

>> GO TO 3.

NO

>> Repair or replace damaged parts.

3.

CHECK HARNESS BETWEEN BCM AND TIRE PRESSURE RECEIVER 

1.

Disconnect tire pressure receiver harness connector.

2.

Check the continuity between BCM harness connector and tire pressure receiver harness connector.

DTC 

Display item

Malfunction detected condition

Possible case

C1734

CONTROL UNIT

Tire pressure monitoring system malfunction in BCM

BCM malfunction

BCM

—

Voltage

(Approx.)

Connector

Terminal

M118

1

Ground

Battery voltage

M119

11

BCM

—

Continuity

Connector

Terminal

M119

13

Ground

Existed

Revision: 2011 November

2011 MURANO

C1734 BCM

WT-31

< DTC/CIRCUIT DIAGNOSIS >

C

D

F

G

H

I

J

K

L

M

A

B

WT

N

O

P

3.

Check the continuity between BCM harness connector and ground.

Is the inspection result normal?

YES

>> GO TO 4.

NO

>> Repair or replace damaged parts.

4.

CHECK BCM 

Check the BCM input/output signal. Refer to 

BCS-47, "Reference Value"

.

Is the inspection result normal?

YES

>> INSPECTION END

NO

>> GO TO 5.

5.

CHECK BCM HARNESS CONNECTOR

Check the BCM pin terminals for damage or loose connection with harness connector.

Is the inspection result normal?

YES

>> Replace BCM. Refer to 

BCS-85, "Exploded View"

.

NO

>> Check for looseness or damage at the harness connector pins of the BCM. Repair or replace if

necessary.

BCM

Tire pressure receiver

Continuity

Connector

Terminal

Connector

Terminal

M123

137

M21

1

Existed

138

4

139

2

BCM

—

Continuity

Connector

Terminal

M123

137

Ground

Not existed

138

139

Revision: 2011 November

2011 MURANO

WT-32

< DTC/CIRCUIT DIAGNOSIS >

TIRE PRESSURE RECEIVER

TIRE PRESSURE RECEIVER

Component Function Check

INFOID:0000000006260305

1.

TIRE PRESSURE MONITORING SYSTEM OPERATION

With CONSULT-III 

1.

Drive for 3 minutes at a speed of 40 km/h (25 MPH) or more, then drive normally for 10 minutes.

2.

On “DATA MONITOR”, select “AIR PRESS FL”, “AIR PRESS FR”, “AIR PRESS RR” and “AIR PRESS
RL”, and check that the tire pressures match the standard value.

CAUTION:

Stop the vehicle and within 5 minutes, use CONSULT-III “DATA MONITOR” to display the tire pressure
for all wheels.

Is the inspection result normal?

YES

>> INSPECTION END

NO

>> Perform trouble diagnosis. Refer to 

WT-32, "Diagnosis Procedure"

.

Diagnosis Procedure

INFOID:0000000006260306

1.

CHECK TIRE PRESSURE RECEIVER SIGNAL

1.

Turn the ignition switch ON.

CAUTION:

Never start the engine.

2.

Check tire pressure receiver connector and ground signal with oscilloscope.

Is the inspection result normal?

YES

>> INSPECTION END

NO

>> GO TO 2.

2.

CHECK TIRE PRESSURE RECEIVER INPUT VOLTAGE

1.

Turn the ignition switch OFF.

2.

Disconnect tire pressure receiver connector.

3.

Turn the ignition switch ON.

Monitor item

Condition

Displayed value

AIR PRESS FL

Drive for 3 minutes at a speed of 40 km/h (25 MPH) or 
more, then drive normally for 10 minutes.

Internal pressure of tires

AIR PRESS FR

AIR PRESS RR

AIR PRESS RL

Tire pressure receiver

—

Condition

Voltage

(Approx.)

Connector

Terminal

M21

2

Ground

Stand by state

When receiving the signal from the trans-
mitter

OCC3881D

OCC3880D

Revision: 2011 November

2011 MURANO

TIRE PRESSURE RECEIVER

WT-33

< DTC/CIRCUIT DIAGNOSIS >

C

D

F

G

H

I

J

K

L

M

A

B

WT

N

O

P

CAUTION:

Never start the engine.

4.

Check voltage between tire pressure receiver connector and ground.

Is the inspection result normal?

YES

>> GO TO 3.

NO

>> Repair or replace damaged parts. 

3.

CHECK TIRE PRESSURE RECEIVER GROUND CIRCUIT

1.

Turn the ignition switch OFF.

2.

Disconnect BCM harness connector.

3.

Check continuity between BCM harness connector and tire pressure receiver connector.

4.

Check continuity between BCM harness connector and ground.

Is the inspection result normal?

YES

>> GO TO 4.

NO

>> Repair or replace damaged parts. 

4.

CHECK BCM CIRCUIT

Inspect the BCM circuit. Refer to 

WT-30, "Diagnosis Procedure"

.

Is the BCM circuit normal?

YES

>> Replace tire pressure receiver. Refer to 

WT-51, "Removal and Installation"

.

NO

>> Replace BCM. Refer to 

BCS-85, "Exploded View"

.

Tire pressure receiver

—

Voltage

(Approx.)

Connector

Terminal

M21

4

Ground

5.0 V

BCM

Tire pressure receiver

Continuity

Connector

Terminal

Connector

Terminal

M123

137

M21

1

Existed

BCM

—

Continuity

Connector

Terminal

M123

137

Ground

Not existed

Revision: 2011 November

2011 MURANO

WT-34

< DTC/CIRCUIT DIAGNOSIS >

LOW TIRE PRESSURE WARNING LAMP

LOW TIRE PRESSURE WARNING LAMP

Component Function Check

INFOID:0000000006260309

1.

CHECK THE ILLUMINATION OF THE LOW TIRE PRESSURE WARNING LAMP

Check that the low tire pressure warning lamp is turned OFF after illuminating for approximately 1 second,
when the ignition switch is turned ON.

Is the inspection result normal?

YES

>> INSPECTION END

NO

>> Perform trouble diagnosis. Refer to 

WT-34, "Diagnosis Procedure"

. 

Diagnosis Procedure

INFOID:0000000006260310

1.

POWER SUPPLY AND GROUND CIRCUIT

Check power supply and ground circuit. Refer to 

WT-35, "Diagnosis Procedure"

. 

Is the inspection result normal?

YES

>> GO TO 2.

NO

>> Repair or replace damaged parts.

2.

PERFORM SELF-DIAGNOSIS

With CONSULT-III

Perform “SELF-DIAG RESULTS” in “AIR PRESSURE MONITOR” of “BCM”.
Is any DTC detected?

YES

>> Check the DTC. Refer to 

MWI-77, "DTC Index"

. 

NO

>> GO TO 3.

3.

CHECK LOW TIRE PRESSURE WARNING LAMP SIGNAL

With CONSULT-III

1.

Turn the ignition switch ON.

CAUTION:

Never start the engine.

2.

Perform “DATA MONITOR” in “AIR PRESSURE MONITOR” of “BCM”.

3.

Select “BCM” in “DATA MONITOR”, and check that the low tire pressure warning lamp is turned OFF after
illuminating for approximately 1 second, when the ignition switch is turned ON.

Is the inspection result normal?

YES

>> Check the combination meter. Refer to 

MWI-6, "METER SYSTEM : System Description"

.

NO

>> Replace the BCM. Refer to 

BCS-85, "Exploded View"

. 

Revision: 2011 November

2011 MURANO

POWER SUPPLY AND GROUND CIRCUIT

WT-35

< DTC/CIRCUIT DIAGNOSIS >

C

D

F

G

H

I

J

K

L

M

A

B

WT

N

O

P

POWER SUPPLY AND GROUND CIRCUIT

Diagnosis Procedure

INFOID:0000000006260311

1.

POWER SUPPLY SYSTEM CHECK

1.

Turn the ignition switch OFF.

2.

Disconnect the BCM harness connector.

3.

Turn the ignition switch ON.

CAUTION:

Never start the engine.

4.

Check the voltage between the BCM harness connector and the ground.

Is the inspection result normal?

YES

>> GO TO 2.

NO

>> Repair or replace damaged parts.

2.

GROUND SYSTEM INSPECTION

1.

Turn the ignition switch OFF.

2.

Check the continuity between the BCM harness connector and the ground.

Is the inspection result normal?

YES

>> • Check the 10A fuse [No. 10 in fuse block (J/B)].

• Check the 40A fusible link [No. L in fuse block].

NO

>> Repair or replace damaged parts.

BCM

—

Voltage

Connector

Terminal

M118

1

Ground

Battery voltage

M119

11

BCM

—

Continuity

Connector

Terminal

M119

13

Ground

Existed

Revision: 2011 November

2011 MURANO

WT-36

< SYMPTOM DIAGNOSIS >

TPMS

SYMPTOM DIAGNOSIS

TPMS

Symptom Table 

INFOID:0000000006260312

LOW TIRE PRESSURE WARNING LAMP SYMPTOM CHART

Revision: 2011 November

2011 MURANO