Nissan Murano Z51 (2011 year). Manual

IP-20

< REMOVAL AND INSTALLATION >

CENTER CONSOLE ASSEMBLY

CENTER CONSOLE ASSEMBLY

Exploded View

INFOID:0000000006418471

Instrument lower cover RH

Instrument lower cover LH

Instrument stay LH

Front console bracket

Console reinforcement

Lower console finisher LH

Console harness

Inside key antenna

Rear console pocket

10. Console mask

11.

Console rear finisher

12. Center console assembly

13. Socket and bulb

14. Console finisher assembly

15. Cup holder assembly

16. Ashtray

17. Cigarette lighter ring

18. Cigarette lighter complete

19. Socket knob

20. Socket inner case

21. Console mat

22. Console switch finisher

23. USB connector

24. Lower console assembly

25. Auxiliary input jacks

26. Socket knob

27. Socket ring

28. Socket inner case

29. Lower console finisher RH

30. Front console pocket

JMJIA4761ZZ

Revision: 2011 November

2011 MURANO

CENTER CONSOLE ASSEMBLY

IP-21

< REMOVAL AND INSTALLATION >

Removal and Installation

INFOID:0000000006260960

CAUTION:

When removing, always use a remover tool that is made of plastic.

REMOVAL

Remove selector lever knob. Refer to

TM-163, "Removal and Installation"

Remove console finisher assembly.
1.

Open the console lid.

Remove console finisher assembly (1) fixing pawls and
metal clips with remover tool (A).

Pull up console finisher assembly.

Disconnect harness connectors.

Remove front console pocket.
1.

Remove front console pocket (1) fixing screw (A).

Pull up front console pocket, and then disengage metal
clips.

Disconnect harness connectors.

Remove rear console pocket.
1.

Open the rear console pocket (1).

Release rear console pocket lock.

Remove console rear finisher.
1.

Remove console mask (1) with flat-bladed screwdriver (A).

: Pawl

: Metal clip

JMJIA1334ZZ

: Metal clip

JMJIA1335ZZ

JMJIA1336ZZ

: Pawl

JMJIA1337ZZ

Revision: 2011 November

2011 MURANO

IP-22

< REMOVAL AND INSTALLATION >

CENTER CONSOLE ASSEMBLY

Remove console rear finisher (2) fixing screws (A).

Pull back console rear finisher.

Disconnect harness connectors.

Remove center console assembly.
1.

Remove center console assembly (1) fixing screws (A).

Lift up back side and pull back.

Remove instrument lower cover LH and RH.
1.

Disengage instrument lower cover LH (1) fixing pawls.

Pull back instrument lower cover LH.

Disengage instrument lower cover RH (2) fixing pawls and
clip.

Pull the instrument lower cover RH crosswise.

Remove lower console finisher LH and RH.
1.

Remove lower console finisher LH (1) fixing screws (A).

Remove lower console finisher LH fixing clip (B).

Remove lower console finisher LH fixing clip (C).

Pull the console finisher LH crosswise.

Remove lower console finisher RH (2) fixing screws (D).

Remove lower console finisher RH fixing clip (E).

Remove lower console finisher RH fixing clip (F).

Pull the console finisher RH crosswise.

Remove lower console assembly.
1.

Remove lower console assembly (1) fixing screws (A).

Remove lower console assembly fixing bolts (B).

Disconnect harness connectors.

: Metal clip

JMJIA1401ZZ

JMJIA1338ZZ

: Clip

: Pawl

JMJIA1339ZZ

: Clip

JMJIA1340ZZ

JMJIA1341ZZ

Revision: 2011 November

2011 MURANO

CENTER CONSOLE ASSEMBLY

IP-23

< REMOVAL AND INSTALLATION >

NOTE:
Remove following parts after removing lower console assembly.
• USB connector: Refer to

AV-286, "Removal and Installation"

• Auxiliary input jacks: Refer to

AV-285, "Removal and Installation"

• Console power socket: Refer to

PWO-11, "CONSOLE POWER SOCKET : Removal and Installation"

10. Remove CVT shift selector. Refer to

TM-163, "Removal and Installation"

11. Remove console reinforcement.

Remove console reinforcement (1) fixing nuts (A).

Remove console reinforcement fixing bolts (B).

Remove harness clip.

12. Remove instrument stay LH fixing nuts, and then remove instrument stay LH.

13. Remove front console bracket fixing bolt and nuts, and then remove front console bracket.

INSTALLATION

Install in the reverse order of removal.

: Clip

JMJIA1342ZZ

Revision: 2011 November

2011 MURANO

DESCRIPTION

LU-3

< SYSTEM DESCRIPTION >

Engine Lubrication System Schematic

INFOID:0000000006258173

JPBIA1775GB

Revision: 2011 November

2011 MURANO

LU-4

< PRECAUTION >

PRECAUTIONS

PRECAUTION

PRECAUTIONS

Precaution for Liquid Gasket

INFOID:0000000006258174

LIQUID GASKET APPLICATION PROCEDURE

Remove old liquid gasket adhering to the liquid gasket application surface and the mating surface.
• Remove liquid gasket completely from the liquid gasket application surface, mounting bolts, and bolt

holes.

Wipe the liquid gasket application surface and the mating surface with white gasoline (lighting and heating
use) to remove adhering moisture, grease and foreign materials.

Apply liquid gasket to the liquid gasket application surface.
Use Genuine RTV Silicone Sealant or equivalent. Refer to

GI-22, "Recommended Chemical Prod-

ucts and Sealants"

• Within 5 minutes of liquid gasket application, install in the mating component.
• If liquid gasket protrudes, wipe it off immediately.
• Never retighten mounting bolts or nuts after the installation.
• After 30 minutes or more have passed from the installation, fill engine oil and engine coolant.

Revision: 2011 November

2011 MURANO

PREPARATION

LU-5

< PREPARATION >

PREPARATION

Special Service Tool

INFOID:0000000006258175

The actual shapes of Kent-Moore tools may differ from those of special service tools illustrated here.

Commercial Service Tool

INFOID:0000000006258176

Tool number
(Kent-Moore No.)
Tool name

Description

ST25051001
(J-25695-1)
Oil pressure gauge

Measuring oil pressure
Maximum measuring range: 2,452 kPa (25

kg/cm

, 356 psi)

ST25052000
(J-25695-2)
Hose

Adapting oil pressure gauge to oil pan (upper)

KV10115801
(J-38956)
Oil filter wrench

Removing oil filter
a: 64.3 mm (2.531 in)

NT050

S-NT559

S-NT375

Tool name

Description

Power tools

Loosening nuts and bolts

PBIC0190E

Revision: 2011 November

2011 MURANO

ENGINE OIL

LU-7

< PERIODIC MAINTENANCE >

PERIODIC MAINTENANCE

ENGINE OIL

Inspection

INFOID:0000000006258177

ENGINE OIL LEVEL

NOTE:
Before starting engine, put vehicle horizontally and check the engine oil level. If engine is already started, stop
it and allow 10 minutes before checking.

Pull out oil level gauge and wipe it clean.

Insert oil level gauge and check the engine oil level is within the
range shown in the figure.

If it is out of range, adjust it.

ENGINE OIL APPEARANCE

• Check engine oil for white turbidity or heavy contamination.
• If engine oil becomes turbid and white, it is highly probable that it is contaminated with engine coolant.

Repair or replace damaged parts.

ENGINE OIL LEAKAGE

Check for engine oil leakage around the following areas:
• Oil pans (lower and upper)
• Oil pan drain plug
• Oil pressure switch
• Oil temperature sensor
• Oil filter
• Water pump cover
• Oil cooler
• Valve timing control covers (bank 1 and bank 2)
• Intake valve timing control solenoid valve (bank 1 and bank 2)
• Mating surface between cylinder head and rocker cover
• Mating surface between front timing chain case and rear timing chain case
• Mating surface between rear timing chain case and cylinder head
• Mating surface between rear timing chain case and cylinder block
• Mating surface between rear timing chain case and oil pan (upper)
• Mating surface between cylinder block and cylinder head
• Crankshaft oil seals (front and rear)
• Camshaft position sensor (PHASE)

OIL PRESSURE CHECK

WARNING:

• Be careful not to get burn yourself, as engine oil may be hot.
• Oil pressure check should be done in “Parking position”.

Check the engine oil level.

Remove splash guard (RH). Refer to

EXT-23, "FENDER PROTECTOR : Exploded View"

PBIC4202E

Revision: 2011 November

2011 MURANO

LU-8

< PERIODIC MAINTENANCE >

ENGINE OIL

Disconnect harness connector at oil pressure switch (2), and
remove oil pressure switch using deep socket (commercial ser-
vice tool).

CAUTION:

Never drop or shock oil pressure switch.

Install the oil pressure gauge [SST: ST25051001 (J-25695-1)]
(A) and hose [SST: ST25052000 (J-25695-2)] (B).

Start the engine and warm it up to normal operating temperature.

Check the engine oil pressure with engine running under no-load.
NOTE:
When the engine oil temperature is low, the engine oil pressure becomes high.

If difference is extreme, check engine oil passage and oil pump for engine oil leakage.

After the inspections, install oil pressure switch as follows:

Remove old liquid gasket adhering to oil pressure switch and the mating surface.

Apply liquid gasket and tighten oil pressure switch to the specification.
Use Genuine RTV Silicone Sealant or equivalent. Refer to

GI-22, "Recommended Chemical Prod-

ucts and Sealants"

After warming up engine, check there is no leakage of engine oil with running engine.

Draining

INFOID:0000000006258178

WARNING:

• Be careful not to get burn yourself, as engine oil may be hot.
• Prolonged and repeated contact with used engine oil may cause skin cancer. Try to avoid direct skin

contact with used engine oil. If skin contact is made, wash thoroughly with soap or hand cleaner as
soon as possible.

Warm up the engine, and check for engine oil leakage from engine components. Refer to

LU-7, "Inspec-

tion"

Stop the engine and wait for 10 minutes.

Loosen oil filler cap.

: Oil filter

: Vehicle front

JPBIA1677ZZ

JPBIA0074ZZ

Engine oil pressure

: Refer to

LU-16, "Engine Oil Pressure"

Tightening torque

: Refer to

EM-43, "Exploded View"

Revision: 2011 November

2011 MURANO

ENGINE OIL

LU-9

< PERIODIC MAINTENANCE >

Remove drain plug (1) and then drain engine oil.

Refilling

INFOID:0000000006258179

Install drain plug with new drain plug washer. Refer to

EM-43, "Exploded View"

CAUTION:

Be sure to clean drain plug and install with new drain plug washer.

Refill with new engine oil.
Engine oil specification and viscosity: Refer to

MA-15, "FOR NORTH AMERICA : Fluids and Lubri-

cants"

(for North America) or

MA-16, "FOR MEXICO : Fluids and Lubricants"

(for Mexico).

CAUTION:

• When filling engine oil, never pull out oil level gauge.
• The refill capacity depends on the engine oil temperature and drain time. Use these specifica-

tions for reference only.

• Always use oil level gauge to determine the proper amount of engine oil in engine.

Warm up the engine and check area around drain plug and oil filter for engine oil leakage.

Stop the engine and wait for 10 minutes.

Check the engine oil level. Refer to

LU-7, "Inspection"

: Vehicle front

JPBIA1676ZZ

Tightening torque

: Refer to

EM-43, "Exploded View"

Engine oil capacity

: Refer to

LU-16, "Periodical Maintenance Specification"

Revision: 2011 November

2011 MURANO

LU-10

< PERIODIC MAINTENANCE >

OIL FILTER

OIL FILTER

Removal and Installation

INFOID:0000000006258180

REMOVAL

CAUTION:

• Oil filter is provided with relief valve. Use genuine NISSAN oil filter or equivalent.
• Be careful not to get burned when engine and engine oil may be hot.
• When removing, prepare a shop cloth to absorb any engine oil leakage or spillage.
• Never allow engine oil to adhere to drive belt.
• Completely wipe off any engine oil that adheres to engine and vehicle.

Remove splash guard (RH). Refer to

EXT-23, "FENDER PROTECTOR : Exploded View"

Using oil filter wrench [SST: KV10115801 (J-38956)] (A), remove
oil filter.

INSTALLATION

Remove foreign materials adhering to oil filter installation surface.

Apply engine oil to the oil seal contact surface of new oil filter.

Screw oil filter manually until it touches the installation surface,
then tighten it by 2/3 turn (A). Or tighten to the specification.

Inspection

INFOID:0000000006258181

INSPECTION AFTER INSTALLATION

Check the engine oil level. Refer to

LU-7, "Inspection"

Start the engine, and check there is no leakage of engine oil.

Stop the engine and wait for 10 minutes.

Check the engine oil level, and adjust the level. Refer to

LU-7, "Inspection"

: Vehicle front

JPBIA1678ZZ

SMA010

Oil filter:

: 17.7 N·m (1.8 kg-m, 13 ft-lb)

JPBIA0077ZZ

Revision: 2011 November

2011 MURANO

OIL COOLER

LU-11

< REMOVAL AND INSTALLATION >

REMOVAL AND INSTALLATION

OIL COOLER

Exploded View

INFOID:0000000006258182

Removal and Installation

INFOID:0000000006258183

REMOVAL

WARNING:

Be careful not to get burn yourself, as engine oil and engine coolant may be hot.
NOTE:
When remove oil cooler only, step 2 is unnecessary.
1.

Remove splash guard (RH). Refer to

EXT-23, "FENDER PROTECTOR : Exploded View"

Drain engine coolant from radiator and cylinder block. Refer to

CO-11, "Draining"

and

EM-90, "Setting"

NOTE:
Perform this step when removing water pipes.

Remove oil filter. Refer to

LU-10, "Removal and Installation"

CAUTION:

Never spill engine oil on drive belt.

Disconnect water hoses from oil cooler.

Connector bolt

Copper gasket

Water drain plug

Water pipe

Bracket

Clamp

Water hose

Relief valve

Oil cooler

10.

Connector bolt

11.

Oil filter

12.

Water hose

13.

Water pipe

14.

Water hose

To water connector

Refer to

LU-10

: Engine front

Refer to

GI-4, "Components"

for symbols in the figure.

JPBIA1679GB

Revision: 2011 November

2011 MURANO

LU-12

< REMOVAL AND INSTALLATION >

OIL COOLER

• When removing oil cooler only, pinching water hoses near oil cooler to prevent engine coolant from spill-

ing out.

• Remaining engine coolant in piping will come out. Use a tray to collect it.

CAUTION:

• Perform this step when the engine is cold.
• Never spill engine coolant on drive belt.

Remove connector bolt, and remove oil cooler.

CAUTION:

Never spill engine oil to rubber parts such as drive belt.

Remove water pipes if necessary.

INSTALLATION

Note the following, and install in the reverse order of removal.
• Check that no foreign objects are adhering to the installation surfaces of oil cooler and oil pan (upper).
• Align cutout (B) on oil cooler (2) with protrusion (A) on oil pan

(upper) side, and tighten connector bolt (1).

Inspection

INFOID:0000000006258184

INSPECTION AFTER REMOVAL

Oil Cooler

Check oil cooler for cracks. Check oil cooler for clogging by blowing through engine coolant inlet. If necessary,
replace oil cooler.

Relief Valve

Inspect relief valve for movement, cracks and breaks by pushing the ball. If replacement is necessary, remove
relief valve by prying it out with a suitable tool. Install a new relief valve in place by tapping it.

INSPECTION AFTER INSTALLATION

Check the engine oil level and the engine coolant level and add engine oil and engine coolant. Refer to

LU-7, "Inspection"

and

CO-11, "Inspection"

Start the engine, and check there is no leakage of engine oil or engine coolant.

Stop the engine and wait for 10 minutes.

Check the engine oil level and the engine coolant level again. Refer to

JPBIA1680ZZ

Revision: 2011 November

2011 MURANO

Nissan Murano Z51 (2011 year). Manual - part 39