Nissan Murano Z50 (2007 year). Manual - part 170

 

  Index      Manuals     Nissan Murano Z50 (2007 year) - Service and Repair Manual

 

Search            copyright infringement  

 

 

 

 

 

 

 

 

Content      ..     168      169      170      171     ..

 

 

Nissan Murano Z50 (2007 year). Manual - part 170

 

 

TROUBLE DIAGNOSIS

ATC-55

C

D

E

F

G

H

I

K

L

M

A

B

ATC

Revision: 2006 July

2007 Murano

Operational Check

NJS000AX

The purpose of the operational check is to check if the individual system operates properly.

CHECKING MEMORY FUNCTION

1.

Turn temperature control dial clockwise until 32

°

C (90

°

F) is displayed.

2.

Press OFF switch.

3.

Turn ignition switch OFF.

4.

Turn ignition switch ON.

5.

Press the AUTO switch.

6.

Confirm that the set temperature remains at previous temperature.

7.

Press OFF switch.

If NG, go to trouble diagnosis procedure for 

ATC-94, "Memory Function"

 .

If OK, continue the check.

CHECKING BLOWER

1.

Turn fan control dial clockwise. Blower should operate on low speed. The fan symbol should have one
blade lit.

2.

Turn fan control dial clockwise again, and continue checking blower speed and fan symbol until all speeds
are checked.

3.

Leave blower on max. speed. 

If NG, go to trouble diagnosis procedure for 

ATC-72, "Blower Motor Circuit"

 .

If OK, continue the check.

CHECKING DISCHARGE AIR

1.

Press MODE switch and DEF switch.

2.

Each position indicator should change shape.

3.

Confirm that discharge air comes out according to the air distri-
bution table. Refer to 

ATC-32, "Discharge Air Flow"

 .

If NG, go to trouble diagnosis procedure for 

ATC-63, "Mode Door

Motor Circuit"

 .

If OK, continue the check.

NOTE:
Confirm that the compressor clutch is engaged (sound or visual
inspection) and intake door position is at FRESH when the DEF or
D/F is selected.

CHECKING INTAKE AIR

1.

Press recirculation (REC) switch. Recirculation indicator should illuminate.

2.

Press fresh (FRE) switch. Fresh indicator should illuminate.

3.

Listen for intake door position change. (Slight change of blower sound can be heard.)

If NG, go to trouble diagnosis procedure for 

ATC-69, "Intake Door Motor Circuit"

 .

If OK, continue the check.

NOTE:
Confirm that the compressor clutch is engaged (sound or visual inspection) and intake door position is at
FRESH when the DEF or D/F is selected.

CHECKING TEMPERATURE DECREASE

1.

Turn temperature control dial (driver side) counterclockwise until 18

°

C (60

°

F) is displayed.

2.

Check for cold air at discharge air outlets.

If NG, go to trouble diagnosis procedure for 

ATC-83, "Insufficient Cooling"

 .

If OK, continue the check.

Conditions

: Engine running at normal operating temperature

RJIA3995E

ATC-56

TROUBLE DIAGNOSIS

Revision: 2006 July

2007 Murano

CHECKING TEMPERATURE INCREASE

1.

Turn temperature control dial (driver side) clockwise until 32

°

C (90

°

F) is displayed.

2.

Check for hot air at discharge air outlets.

If NG, go to trouble diagnosis procedure for 

ATC-91, "Insufficient Heating"

 .

If OK, continue the check.

CHECK A/C SWITCH

Press AUTO switch and A/C switch. Then A/C switch indicator is turned ON.

Confirm that the compressor clutch engages (sound or visual inspection).

If NG, go to trouble diagnosis procedure for 

ATC-77, "Magnet Clutch Circuit"

 .

If OK, continue the check.

CHECKING AUTO MODE

Press AUTO switch and A/C switch. Then display is indicated AUTO.

Confirm that the compressor clutch engages (sound or visual inspection). (Discharge air and blower
speed will depend on ambient, in-vehicle, and set temperatures.)

If NG, go to trouble diagnosis procedure fo

ATC-57, "Power Supply and Ground Circuit for Auto Amp."

 , then

if necessary, trouble diagnosis procedure for 

ATC-77, "Magnet Clutch Circuit"

 .

If all operational checks are OK (symptom cannot be duplicated), go to Malfunction Simulation Tests in 

GI-27,

"How to Perform Efficient Diagnosis for an Electrical Incident"

  and perform tests as outlined to simulate driv-

ing conditions environment. If symptom appears, refer to 

ATC-36, "SYMPTOM TABLE"

  and perform applica-

ble trouble diagnosis procedures.

TROUBLE DIAGNOSIS

ATC-57

C

D

E

F

G

H

I

K

L

M

A

B

ATC

Revision: 2006 July

2007 Murano

Power Supply and Ground Circuit for Auto Amp.

NJS000AY

SYMPTOM: A/C system does not come on.

INSPECTION FLOW

COMPONENT DESCRIPTION
Unified Meter and A/C Amp. (Automatic Amplifier)

The unified meter and A/C amp. has a built-in microcomputer which
processes information sent from various sensors needed for air con-
ditioner operation. The air mix door motor, mode door motor, intake
door motor, blower motor and compressor are then controlled.
When the various switches and temperature control dials are oper-
ated, data is input to the unified meter and A/C amp. from the display
control unit using CAN communication. 
Self-diagnosis functions are also built into unified meter and A/C
amp. to provide quick check of malfunctions in the auto air condi-
tioner system.

*1

ATC-58, "DIAGNOSIS PROCE-
DURE FOR A/C SYSTEM"

*2

ATC-55, "Operational Check"

*3

AV-120, "Example of Symptoms 
Possible No Malfunction"

*4

AV-39, "A/C and AV Switch Self-
Diagnosis Function"

SJIA1158E

RJIA1758E

ATC-58

TROUBLE DIAGNOSIS

Revision: 2006 July

2007 Murano

Potentio Temperature Control (PTC)

The PTC is built into the A/C and AV switch. It can be set at an inter-
val of 0.5

°

C (1.0

°

F) in the 18

°

C (60

°

F) to 32

°

C (90

°

F) temperature

range by turning temperature control dial. The set temperature is dis-
played.

DIAGNOSIS PROCEDURE FOR A/C SYSTEM

SYMPTOM: A/C system does not come on.

1. 

CHECK POWER SUPPLY CIRCUIT FOR UNIFIED METER AND A/C AMP.

1.

Disconnect unified meter and A/C amp. connector.

2.

Check voltage between unified meter and A/C amp. harness
connector M50 terminals 21, 22 and 35, unified meter and A/C
amp. harness connector M51 terminal 46 and ground.

OK or NG

OK

>> GO TO 2.

NG

>> Check 10A and 15A fuses [Nos. 6, 10, 11, 12 and 19, located in the fuse block (J/B)]. Refer to 

PG-

70, "FUSE BLOCK - JUNCTION BOX (J/B)"

 .

If fuses are OK, check harness for open circuit. Repair or replace if necessary.

If fuses are NG, check harness for short circuit and replace fuse.

SJIA1188E

SJIA0301E

Terminals

Ignition switch position

(+)

(

)

OFF

ACC

ON

Unified meter 

and A/C amp. 

connector 

Terminal 

No.

M50

21

Ground

Battery 
voltage

Battery 
voltage

Battery 
voltage

M50

22

Approx. 0 V

Approx. 0 V

Battery 
voltage

M50

35

Approx. 0 V

Battery 
voltage

Battery 
voltage

M51

46

Approx. 0 V

Approx. 0 V

Battery 
voltage

RJIA1984E

TROUBLE DIAGNOSIS

ATC-59

C

D

E

F

G

H

I

K

L

M

A

B

ATC

Revision: 2006 July

2007 Murano

2. 

CHECK GROUND CIRCUIT FOR UNIFIED METER AND A/C AMP.

1.

Turn ignition switch OFF.

2.

Check continuity between unified meter and A/C amp. harness
connector M50 terminal 29, 30 and ground.

OK or NG

OK

>> Replace unified meter and A/C amp.

NG

>> Repair harness or connector.

LAN System Circuit

NJS000AZ

SYMPTOM: Mode door motor, intake door motor and/or air mix door motor(s) does not operate normally.

DIAGNOSIS PROCEDURE FOR LAN CIRCUIT

1. 

CHECK POWER SUPPLY FOR UNIFIED METER AND A/C AMP. 

1.

Turn ignition switch ON.

2.

Check voltage between unified meter and A/C amp. harness
connector M51 terminal 54 and ground.

OK or NG

OK

>> GO TO 2.

NG

>> Replace unified meter and A/C amp.

29, 30 – Ground

: Continuity should exist.

RJIA1985E

RJIA1775E

54 – Ground

: Battery voltage

RJIA1986E

ATC-60

TROUBLE DIAGNOSIS

Revision: 2006 July

2007 Murano

2. 

CHECK SIGNAL FOR UNIFIED METER AND A/C AMP. 

Confirm A/C LAN signal between unified meter and A/C amp. har-
ness connector M51 terminal 43 and ground using an oscilloscope.

OK or NG

OK

>> GO TO 3.

NG

>> Replace unified meter and A/C amp.

3. 

CHECK POWER SUPPLY FOR EACH DOOR MOTOR

Check voltage between each door motor harness connector terminal
1 and ground.

OK or NG

OK

>> GO TO 4.

NG

>> Repair harness or connector.

4. 

CHECK SIGNAL FOR EACH DOOR MOTOR

Confirm A/C LAN signal between each door motor harness connec-
tor terminal 3 and ground using an oscilloscope.

OK or NG

OK

>> GO TO 5.

NG

>> Repair harness or connector.

Terminals

Voltage

(+)

(

)

Unified meter 

and A/C amp. 

connector

Terminal No.

M51

43

Ground

RJIA1987E

SJIA1453J

1 – Ground

: Battery voltage

RJIA1988E

Door motor

Terminals

Voltage

(+)

(

)

Connector

Terminal 

No.

Mode

M252

3

Ground

Air mix 
(Driver 
side)

M253

3

Air mix 
(Passen-
ger side)

M254

3

Intake

M255

3

RJIA1989E

SJIA1453J

TROUBLE DIAGNOSIS

ATC-61

C

D

E

F

G

H

I

K

L

M

A

B

ATC

Revision: 2006 July

2007 Murano

5. 

CHECK EACH DOOR MOTOR GROUND CIRCUIT

1.

Turn ignition switch OFF.

2.

Disconnect each door motor connector.

3.

Check continuity between each door motor harness connector
terminal 2 and ground.

OK or NG

OK

>> GO TO 6.

NG

>> Repair harness or connector.

6. 

CHECK MOTOR OPERATION

1.

Reconnect each door motor connector.

2.

Turn ignition switch ON.

3.

Confirm operation of each door motor.

OK or NG

OK

>> (Return to operate normally.)

Poor contact in motor connector.

NG

>> (Does not operate normally.)

GO TO 7.

7. 

CHECK AIR MIX DOOR MOTOR AND INTAKE DOOR MOTOR OPERATION

1.

Turn ignition switch OFF.

2.

Disconnect mode door motor, air mix door motor (driver side, passenger side), and intake door motor con-
nectors.

3.

Reconnect air mix door motor (driver side, passenger side) and intake door motor connectors.

4.

Turn ignition switch ON.

5.

Confirm operation of air mix door motor (driver side, passenger side) and intake door motor.

OK or NG

OK

>> [Air mix (driver side, passenger side) and intake door motors operate normally.]

Replace mode door motor.

NG

>> [Air mix (driver side, passenger side) and intake door motors does not operate normally.]

GO TO 8.

8. 

CHECK MODE DOOR MOTOR AND INTAKE DOOR MOTOR OPERATION

1.

Turn ignition switch OFF.

2.

Disconnect air mix door motor (driver side, passenger side) connectors.

3.

Reconnect mode door motor connector.

4.

Turn ignition switch ON.

5.

Confirm operation of mode door motor and intake door motor.

OK or NG

OK

>> (Mode and intake door motors operate normally.)

GO TO 10.

NG

>> (Mode and intake door motors does not operate normally.)

GO TO 9.

2 – Ground

: Continuity should exist.

RJIA1990E

ATC-62

TROUBLE DIAGNOSIS

Revision: 2006 July

2007 Murano

9. 

CHECK MODE DOOR MOTOR AND AIR MIX DOOR MOTOR OPERATION

1.

Turn ignition switch OFF.

2.

Disconnect intake door motor connector.

3.

Reconnect air mix door motor (driver side, passenger side) connectors. 

4.

Turn ignition switch ON.

5.

Confirm operation of mode door motor and air mix door motor (driver side, passenger side).

OK or NG

OK

>> [Mode and air mix door motor (driver side, passenger side) operate normally.]

Replace intake door motor.

NG

>> [Mode and air mix door motor (driver side, passenger side) does not operate normally.]

Replace display and A/C auto amp.

10. 

CHECK AIR MIX DOOR MOTOR OPERATION

1.

Turn ignition switch OFF.

2.

Disconnect air mix door motor (driver side) connector.

3.

Turn ignition switch ON.

4.

Confirm operation of air mix door motor (passenger side).

OK or NG

OK

>> [Air mix door motor (passenger side) operates normally.]

Replace air mix door motor (driver side).

NG

>> [Air mix door motor (passenger side) does not operate normally.]

Replace air mix door motor (passenger side).

TROUBLE DIAGNOSIS

ATC-63

C

D

E

F

G

H

I

K

L

M

A

B

ATC

Revision: 2006 July

2007 Murano

Mode Door Motor Circuit

NJS000B0

SYMPTOM

Air outlet does not change.

Mode door motor does not operate normally.

INSPECTION FLOW

*1

ATC-32, "Discharge Air Flow"

*2

ATC-55, "Operational Check"

*3

ATC-104, "Intake Sensor Circuit"

*4

ATC-48, "FUNCTION CONFIRMA-
TION PROCEDURE"

, see No. 4 to 6.

*5

ATC-95, "Ambient Sensor Circuit"

*6

ATC-98, "In-vehicle Sensor Circuit"

*7

ATC-101, "Sunload Sensor Circuit"

*8

ATC-68, "Air Mix Door Motor PBR 
Circuit"

*9

ATC-48, "FUNCTION CONFIRMA-
TION PROCEDURE"

, see No. 13.

*10

ATC-59, "DIAGNOSIS PROCEDURE 
FOR LAN CIRCUIT"

*11

ATC-65, "Mode Door Motor"

*12

ATC-36, "SYMPTOM TABLE"

SJIA1159E

ATC-64

TROUBLE DIAGNOSIS

Revision: 2006 July

2007 Murano

SYSTEM DESCRIPTION
Component Parts

Mode door control system components are:

Unified meter and A/C amp.

Mode door motor (LCU)

A/C LAN system (PBR built-in mode door motor, intake door motor and air mix door motor)

In-vehicle sensor

Ambient sensor

Sunload sensor

Intake sensor

System Operation

The unified meter and A/C amp. receives data from each of the sensors. The unified meter and A/C amp.
sends air mix door, mode door and intake door opening angle data to the air mix door motor LCUs, mode door
motor LCU and intake door motor LCU.
The air mix door motors, mode door motor and intake door motor read their respective signals according to the
address signal. Opening angle indication signals received from the unified meter and A/C amp. and each of
the motor position sensors are compared by the LCUs in each door motor with the existing decision and open-
ing angles. Subsequently, HOT/COLD, DEF/VENT and FRE/REC operation is selected. The new selection
data are returned to the unified meter and A/C amp.

Mode Door Control Specification

RJIA1777E

RJIA1778E

TROUBLE DIAGNOSIS

ATC-65

C

D

E

F

G

H

I

K

L

M

A

B

ATC

Revision: 2006 July

2007 Murano

COMPONENT DESCRIPTION
Mode Door Motor

The mode door motor is attached to the heater & cooling unit assem-
bly. It rotates so that air is discharged from the outlet set by the uni-
fied meter and A/C amp. Motor rotation is conveyed to a link which
activates the mode door.

DIAGNOSIS PROCEDURE FOR MODE DOOR MOTOR

SYMPTOM: Mode door motor does not operate normally.
Perform diagnosis procedure. Refer to 

ATC-59, "DIAGNOSIS PROCEDURE FOR LAN CIRCUIT"

 .

RJIA3961E

ATC-66

TROUBLE DIAGNOSIS

Revision: 2006 July

2007 Murano

Air Mix Door Motor Circuit

NJS000B1

SYMPTOM

Discharge air temperature does not change.

Air mix door motor does not operate normally.

INSPECTION FLOW

*1

ATC-48, "FUNCTION CONFIRMA-
TION PROCEDURE"

, see No. 4 to 6.

*2

ATC-95, "Ambient Sensor Circuit"

*3

ATC-98, "In-vehicle Sensor Circuit"

*4

ATC-101, "Sunload Sensor Circuit"

*5

ATC-68, "Air Mix Door Motor PBR Cir-
cuit"

*6

ATC-48, "FUNCTION CONFIRMA-
TION PROCEDURE"

, see No. 13.

*7

ATC-59, "LAN System Circuit"

*8

ATC-68, "Air Mix Door Motor"

*9

ATC-55, "Operational Check"

*10

ATC-36, "SYMPTOM TABLE"

*11

ATC-104, "Intake Sensor Circuit"

SJIA1229E

TROUBLE DIAGNOSIS

ATC-67

C

D

E

F

G

H

I

K

L

M

A

B

ATC

Revision: 2006 July

2007 Murano

SYSTEM DESCRIPTION
Component Parts

Air mix door control system components are:

Unified meter and A/C amp.

Air mix door motor (LCU)

A/C LAN system (PBR built-in mode door motor, intake door motor and air mix door motor)

In-vehicle sensor

Ambient sensor

Sunload sensor

Intake sensor

System Operation

The unified meter and A/C amp. receives data from each of the sensors. The unified meter and A/C amp.
sends air mix door, mode door and intake door opening angle data to the air mix door motor LCUs, mode door
motor LCU and intake door motor LCU.
The air mix door motors, mode door motor and intake door motor read their respective signals according to the
address signal. Opening angle indication signals received from the unified meter and A/C amp. and each of
the motor position sensors are compared by the LCUs in each door motor with the existing decision and open-
ing angles. Subsequently, HOT/COLD, DEF/VENT and FRE/REC operation is selected. The new selection
data are returned to the unified meter and A/C amp.

Air Mix Door Control Specification

RJIA1781E

RJIA1782E

ATC-68

TROUBLE DIAGNOSIS

Revision: 2006 July

2007 Murano

COMPONENT DESCRIPTION
Air Mix Door Motor

The air mix door motors are attached to the heater & cooling unit
assembly. It rotates so that the air mix door is opened or closed to a
position set by the unified meter and A/C amp. Motor rotation is then
conveyed through a shaft and the air mix door position feedback is
then sent to the unified meter and A/C amp. by PBR built-in air mix
door motor.

DIAGNOSIS PROCEDURE FOR AIR MIX DOOR

SYMPTOM: Discharge air temperature does not change.
Perform diagnosis procedure. Refer to 

ATC-59, "DIAGNOSIS PROCEDURE FOR LAN CIRCUIT"

 .

Air Mix Door Motor PBR Circuit

NJS000B2

SYMPTOM

Discharge air temperature does not change.

PBR circuit is open or shorted.

DIAGNOSIS PROCEDURE FOR AIR MIX DOOR MOTOR PBR

Perform diagnosis procedure. Refer to 

ATC-59, "DIAGNOSIS PROCEDURE FOR LAN CIRCUIT"

 .

RJIA3963E

RJIA3964E

TROUBLE DIAGNOSIS

ATC-69

C

D

E

F

G

H

I

K

L

M

A

B

ATC

Revision: 2006 July

2007 Murano

Intake Door Motor Circuit

NJS000B3

SYMPTOM

Intake door does not change.

Intake door motor does not operate normally.

INSPECTION FLOW

*1

ATC-48, "FUNCTION CONFIRMA-
TION PROCEDURE"

, see No. 4 to 6.

*2

ATC-95, "Ambient Sensor Circuit"

*3

ATC-98, "In-vehicle Sensor Circuit"

*4

ATC-101, "Sunload Sensor Circuit"

*5

ATC-68, "Air Mix Door Motor PBR 
Circuit"

*6

ATC-48, "FUNCTION CONFIRMA-
TION PROCEDURE"

, see No. 13.

*7

ATC-59, "LAN System Circuit"

*8

ATC-71, "Intake Door Motor"

*9

ATC-55, "Operational Check"

*10

ATC-36, "SYMPTOM TABLE"

*11

ATC-104, "Intake Sensor Circuit"

SJIA1160E

ATC-70

TROUBLE DIAGNOSIS

Revision: 2006 July

2007 Murano

SYSTEM DESCRIPTION
Component Parts

Intake door control system components are:

Unified meter and A/C amp.

Intake door motor (LCU)

A/C LAN system (PBR built-in mode door motor, intake door motor and air mix door motor)

In-vehicle sensor

Ambient sensor

Sunload sensor

Intake sensor

System Operation

The intake door control determines intake door position based on the ambient temperature, the intake air tem-
perature and the in-vehicle temperature. When shifting mode position D/F, when the DEF or OFF switches are
pressed, or when A/C switch is OFF, the unified meter and A/C amp. sets the intake door at the FRE position.

Intake Door Control Specification

PJIA0122E

RJIA1787E

 

 

 

 

 

 

 

Content      ..     168      169      170      171     ..