Nissan Murano Z50 (2007 year). Manual

REAR FINAL DRIVE ASSEMBLY

RFD-21

RFD

Revision: 2006 July

2007 Murano

DISASSEMBLY
Electric Controlled Coupling Assembly

Remove connector bracket.

Put matching mark on the thread edge of electric controlled cou-
pling. The matching mark should be in line with the matching
mark on companion flange.

CAUTION:

For matching mark, use paint. Do not damage electric con-
trolled coupling.

NOTE:
When replacing electric controlled coupling, matching mark is
not necessary.

Remove companion flange lock nut, using a flange wrench.

Remove companion flange.

Remove coupling cover.

Remove front oil seal from coupling cover, using flat-bladed
screwdriver.

CAUTION:

Be careful not to damage coupling cover.

Remove electric controlled coupling assembly from drive pinion
in gear carrier.

Remove AWD solenoid harness.

PDIA0455E

PDIA0442E

PDG0213D

PDIA0443E

RFD-22

REAR FINAL DRIVE ASSEMBLY

Revision: 2006 July

2007 Murano

Remove coupling front bearing, using pullers and then take off
bearing shim from electric controlled coupling.

10. Remove center oil seal from gear carrier.

Differential Assembly

Remove side oil seal from gear carrier and rear cover, using flat-
bladed screwdriver.

CAUTION:

Be careful not to damage gear carrier and rear cover.

Remove rear cover mounting bolts.

Set drifts to the right and left side bearing adjusting shims indi-
vidually. Press differential case assembly with side bearing to
remove gear carrier assembly and rear cover assembly.

CAUTION:

The pressure shall be as low as possible to remove gear
carrier assembly and rear cover assembly. The maximum
pressure shall be 10 kN (1 ton, 1.1 US ton, 1.0 Imp ton).

NOTE:
Differential case assembly, side bearings, and adjusting shims
are compressed and integrated in gear carrier and rear cover.

Remove drain plug and filler plug.

Remove side bearing adjusting shims and side bearing outer races.

CAUTION:

Mark the side bearing adjusting shims so that the original mounting positions (right/left) can be
identified later.

Remove drive gear mounting bolts and then remove drive gear
from differential case.

PDIA0444E

PDG0216D

Tool number

: KV40100610 (J-26089)

PDIA0065E

PDIA0446E

REAR FINAL DRIVE ASSEMBLY

RFD-23

RFD

Revision: 2006 July

2007 Murano

Remove side bearing inner races, using pullers and the drift.

Pull the lock pin out of pinion mate shaft, using the pin punch.

Remove pinion mate shaft, pinion mate gears, pinion mate
thrust washers, side gears, side gear thrust washers from differ-
ential case.

Drive Pinion Assembly

Remove electric controlled coupling assembly. Refer to

RFD-21, "Electric Controlled Coupling Assembly"

Remove differential case assembly. Refer to

RFD-22, "Differential Assembly"

Fit drive pinion socket onto drive pinion spline. Remove drive
pinion nut, using the pinion nut wrench.

Tool number

: ST33052000 (

—

)

PDIA0459E

Tool number

: ST23550000 (

—

)

PDIA0062E

SDIA0032J

Tool number

A: KV38108400 (

—

)

B: KV38108500 (

—

)

PDIA0054E

RFD-24

REAR FINAL DRIVE ASSEMBLY

Revision: 2006 July

2007 Murano

Press drive pinion assembly out of gear carrier.

CAUTION:

Do not drop drive pinion assembly.

Remove pinion front bearing inner race.

Remove collapsible spacer.

Remove pinion rear bearing inner race from drive pinion, using
pullers.

Using a brass rod, tap pinion front bearing outer race evenly
from the 2 cutouts on gear carrier and remove pinion front bear-
ing outer race.

CAUTION:

Be careful not to damage gear carrier.

Using a brass rod, tap drive pinion adjusting shim evenly from
the 2 cutouts on gear carrier and remove drive pinion adjusting
shims and pinion rear bearing outer race.

CAUTION:

Be careful not to damage the gear carrier.

INSPECTION AFTER DISASSEMBLY

Clean up the disassembled parts. Then, inspect if the parts are worn or damaged. If so, follow the measures
below.

PDIA0445E

PDIA0179E

SDIA0564E

Content

Conditions and Measures

Hypoid gear

●

If the gear teeth do not mesh or line-up correctly, determine the cause and adjust or replace as nec-
essary.

●

If the gears are worn, cracked, damaged, pitted or chipped (by friction) noticeably, replace with new
drive gear and drive pinion as a set.

Bearing

●

If any chipped (by friction), pitted, worn, rusted or scratched mark, or unusual noise from the bearing
is observed, replace as a bearing assembly (as a new set).

Side gear and Pinion mate
gear

●

If any cracks or damage on the surface of the tooth is found, replace.

●

If any worn or chipped mark on the contact sides of the thrust washer is found, replace.

Side gear thrust washer and
pinion mate thrust washer

●

If it is chipped (by friction), damaged, or unusually worn, replace.

Oil seal

●

Whenever disassembled, replace.

●

If wear, deterioration of adherence (sealing force lips), or damage is detected on the lips, replace
them.

Differential case

●

If any wear or crack on the contact sides of the differential case is found, replace.

Companion flange

●

If any chipped mark (about 0.1 mm, 0.004 in) or other damage on the contact sides of the lips of the
companion flange is found, replace.

REAR FINAL DRIVE ASSEMBLY

RFD-25

RFD

Revision: 2006 July

2007 Murano

ASSEMBLY
Drive Pinion Assembly

Install a drive pinion adjusting shim of the same thickness as
was installed prior to disassembly. Press pinion rear bearing
outer race into gear carrier, using the drift.

CAUTION:

●

At first, using a hammer, tap bearing outer race until it
becomes flush to gear carrier.

●

Do not reuse pinion rear bearing outer race.

Press pinion front bearing outer race into gear carrier, using the
drift.

CAUTION:

●

At first, using a hammer, tap bearing outer race until it
becomes flush to gear carrier.

●

Do not reuse pinion front bearing outer race.

Press pinion rear bearing inner race to drive pinion, using the
drift.

CAUTION:

Do not reuse pinion rear bearing inner race.

After checking and adjusting the tooth contact and backlash of
the hypoid gear following the procedure below.

Apply gear oil to the drive pinon rear bearing, and assemble the
drive pinion to the gear carrier.

CAUTION:

Do not assemble a collapsible spacer.

Apply gear oil to drive pinon front bearing, and assemble pinion
front bearing inner race to drive pinion. Using the drifts and
press stand, press pinion front bearing inner race to drive pinon
as far as drive pinion nut can be tightened.

CAUTION:

Do not reuse pinion front bearing inner race.

Temporarily tighten removed drive pinon nut to drive pinion.

NOTE:
Use removed drive pinon nut only for the preload measurement.

Tool number

: ST17130000 (

—

)

PDIA0056E

Tool number

: ST33230000 (J-25805-01)

PDIA0067E

Tool number

: ST23860000 (

—

)

Tool number

A: KV40100610 (J-26089)

B: ST38220000 (

—

)

C: ST23860000 (

—

)

PDIA0068E

PDIA0057E

RFD-26

REAR FINAL DRIVE ASSEMBLY

Revision: 2006 July

2007 Murano

Fit the drive pinon socket onto the drive pinion spline. Using the
pinon nut wrench, tighten drive pinon nut to the specified pre-
load torque.

CAUTION:

Drive pinon nut is tightened with no collapsible spacer. Be
careful not to overtighten it. While measuring the preload,
tighten it by 5

to 10

Apply gear oil to side bearings, and install new side bearing
adjusting shims with the same thickness or re-install the old
ones to the same mounting position they were in prior to disas-
sembly. Install differential case assembly to gear carrier.

CAUTION:

●

The drifts shall be placed on the center of the adjusting
shims.

●

The pressure shall be as low as possible to install gear
carrier assembly to differential assembly. The maximum
pressure shall be 10 kN (1 ton, 1.1 US ton, 1.0 Imp ton).

●

If adjusting shims are installed by tapping, gear carrier may be damaged. Avoid tapping.

Check and adjust the tooth contact. Refer to

RFD-18, "Tooth Contact"

Check and adjust the backlash. Refer to

RFD-20, "Backlash"

Remove dummy cover set, and remove differential case assembly.

Remove drive pinion nut and press drive pinion assembly out of
gear carrier.

CAUTION:

Do not drop drive pinion assembly.

Remove pinion front bearing inner race.

Tool number

A: KV38108400 (

—

)

B: KV38108500 (

—

)

C: ST3127S000 (J-25765-A)

Drive pinion bearing preload:

0.69 – 1.18 N·m (0.07 – 0.12 kg-m, 7 – 10 in-lb)

PDIA0058E

Tool number

: KV40100610 (J-26089)

PDIA0064E

PDIA0445E

REAR FINAL DRIVE ASSEMBLY

RFD-27

RFD

Revision: 2006 July

2007 Murano

Assemble collapsible spacer to drive pinion.

CAUTION:

●

Be careful of the mounting direction of collapsible
spacer.

●

Do not reuse collapsible spacer.

Apply gear oil to drive pinon front bearing, and assemble pinion
front bearing inner race to drive pinion. Using the drifts and
press stand, press the pinion front bearing inner race to drive
pinon as far as drive pinion nut can be tightened.

CAUTION:

Do not reuse pinion front bearing inner race.

Apply anti-corrosive oil to the thread and seat of drive pinion nut, and temporarily tighten drive pinion nut
to drive pinion.

CAUTION:

Do not reuse drive pinion nut.

Fit drive pinon socket onto drive pinion spline. Using the pinon
nut wrench, adjust the drive pinion nut tightening torque and pin-
ion bearing preload torque.

CAUTION:

●

Adjust the lower limit of the drive pinion nut tightening
torque first.

●

If the preload torque exceeds the specified value, replace
collapsible spacer and tighten it again to adjust. Never
loosen drive pinion nut to adjust the preload torque.

●

After adjustment, rotate drive pinion back and forth 2 to 3
times to check for unusual noise, rotation malfunction,
and other malfunctions.

Install differential case assembly. Refer to

RFD-28, "Differential Assembly"

CAUTION:

Do not install rear cover.

10. Install dummy cover set, and check drive gear runout, tooth contact, and backlash. Refer to

RFD-17,

"Drive Gear Runout"

RFD-18, "Tooth Contact"

RFD-20, "Backlash"

11. Remove dummy cover set, then install rear cover, and side oil seal. Refer to

RFD-28, "Differential Assem-

bly"

SDIA2525E

Tool number

A: KV40100610 (J-26089)

B: ST38220000 (

—

)

C: ST23860000 (

—

)

PDIA0057E

Tool number

A: KV38108400 (

—

)

B: KV38108500 (

—

)

C: ST3127S000 (J-25765-A)

Drive pinion nut tightening torque:

181 – 361 N·m (19 – 36 kg-m, 134 – 266 ft-lb)

Drive pinion bearing preload:

0.69 – 1.18 N·m (0.07 – 0.12 kg-m, 7 – 10 in-lb)

PDIA0058E

RFD-28

REAR FINAL DRIVE ASSEMBLY

Revision: 2006 July

2007 Murano

12. Check total preload torque. Refer to

RFD-17, "Total Preload Torque"

13. Install electric controlled coupling assembly. Refer to

RFD-31, "Electric Controlled Coupling Assembly"

14. Check companion flange runout. Refer to

RFD-20, "Companion Flange Runout"

Differential Assembly

Install side gear thrust washers with the same thickness as the
ones installed prior to disassembly or reinstall the old ones on
the side gears.

Install side gear and thrust washer into differential case.

Align 2 pinion mate gears in diagonally opposite positions, then
rotate and install them into differential case after installing thrust
washer to pinion mate gear.

Align the lock pin holes on differential case with shaft, and install
pinion mate shaft.

Measure side gear end play following the procedure below, and select the appropriate side gear thrust
washers.

Place differential case straight up so that side gear to be mea-
sured comes upward.

SDIA0193J

SDIA0036J

SDIA0037J

PDIA0460E

REAR FINAL DRIVE ASSEMBLY

RFD-29

RFD

Revision: 2006 July

2007 Murano

Using thickness gauges, measure the clearance between side
gear back and differential case at 3 different positions, while
rotating side gear. Average the 3 readings, and then measure
the clearance. (Measure the clearance of the other side as well.)

CAUTION:

To prevent side gear from tilting, insert thickness gauges
with the same thickness from both sides.

If the back clearance is outside the specification, use a thicker/
thinner side gear thrust washer to adjust. Refer to

RFD-34,

"Side Gear Thrust Washer"

CAUTION:

Select a side gear thrust washer for right and left individu-
ally.

Drive a lock pin into pinion mating shaft, using the pin punch.

CAUTION:

Do not reuse lock pin.

Press side bearing inner races to differential case, using the
drift.

CAUTION:

Do not reuse side bearing inner race.

Apply thread locking sealant into the thread hole of drive gear.

●

Use Genuine Medium Strength Thread Locking Sealant or
equivalent. Refer to

GI-46, "RECOMMENDED CHEMICAL

PRODUCTS AND SEALANTS"

CAUTION:

The drive gear back and threaded holes shall be cleaned
and decreased sufficiently.

Side gear back clearance specification:

0.2 mm (0.008 in) or less.
(Each gear should rotate smoothly without excessive
resistance during differential motion.)

When the back clearance is large:

Use a thicker thrust washer.

When the back clearance is small:

Use a thinner thrust washer.

Tool number

: ST23550000 (

—

)

SDIA0583E

PDIA0062E

Tool number

: KV40105020 (

—

)

PDIA0052E

SPD554

RFD-30

REAR FINAL DRIVE ASSEMBLY

Revision: 2006 July

2007 Murano

Install drive gear to the differential case, and apply anti-corrosive
oil onto threads and seats on the mounting bolts, and then
tighten to the specified torque. Refer to

RFD-16, "COMPO-

NENTS"

10. Apply gear oil to side bearings, and install new side bearing

adjusting shims (2 pieces for one side) with the same thickness
as the ones installed prior to disassembly or re-install the old
ones, with side bearing outer race to differential case.
If side bearing adjusting shims have been already selected, use
them.

CAUTION:

Do not reuse side bearing outer race.

11. Set the drifts to the right and left side bearing adjusting shims

individually. Compress differential case assembly and side bear-
ing to install gear carrier assembly to differential case assembly.

CAUTION:

●

The drift shall be placed on the center of the adjusting
shims.

●

The pressure shall be as low as possible to install differ-
ential assembly into gear carrier assembly. The maximum
pressure shall be 10 kN (1 ton, 1.1 US ton, 1.0 Imp ton).

●

If the adjusting shims are installed by tapping, the gear
carrier may be damaged. Avoid tapping.

12. Install dummy cover set, check and adjust drive gear runout, tooth contact, backlash, and total preload

torque. Refer to

RFD-17, "Drive Gear Runout"

RFD-18, "Tooth Contact"

RFD-20, "Backlash"

RFD-17,

"Total Preload Torque"

13. Remove dummy cover set.

14. Apply liquid gasket to mating surface of rear cover. Overlap both

ends of the bead for at least 3 mm (0.12 in).

●

Use Genuine Silicone RTV or equivalent. Refer to

GI-46,

CAUTION:

Remove old sealant adhering to the mounting surfaces.
Also remove any moisture, oil, or foreign material adhering
to the mounting surfaces.

15. Set the drifts to the right and left side bearing adjusting shims

individually. Compress differential case assembly and side bear-
ing to install rear cover.

CAUTION:

●

The drift shall be placed on the center of the adjusting
shims.

●

The pressure shall be as low as possible to install the
rear cover. The maximum pressure shall be 10 kN (1 ton,
1.1 US ton, 1.0 Imp ton).

●

If rear cover is forced in by tapping, rear cover may be
damaged by adjusting shims. Avoid tapping.

16. Tighten rear cover mounting bolts to the specified torque. Refer to

RFD-16, "COMPONENTS"

Tool number

: KV40100610 (J-26089)

PDIA0466E

PDIA0064E

PDIA0447E

Tool number

: KV40100610 (J-26089)

PDIA0065E

REAR FINAL DRIVE ASSEMBLY

RFD-31

RFD

Revision: 2006 July

2007 Murano

17. Using the drift, drive side oil seals until it becomes flush with the

case end.

CAUTION:

●

Do not reuse oil seal.

●

When installing, do not incline oil seal.

●

Apply multi-purpose grease onto oil seal lips, and gear
oil onto the circumference of oil seal.

18. Check total preload torque. Refer to

RFD-17, "Total Preload

Torque"

Electric Controlled Coupling Assembly

Using the drift, install center oil seal as shown in the figure.

CAUTION:

●

Do not reuse the oil seal.

●

When installing, do not incline oil seal.

●

Apply multi-purpose grease onto oil seal lips, and gear
oil onto the circumference of oil seal.

Install bearing shim and coupling front bearing to electric con-
trolled coupling, using the drift.

CAUTION:

When assembling bearing shim, shim chamfer side should
face electric controlled coupling side.

Connect AWD solenoid harness to electric controlled coupling.

Tool number

: KV38100200 (J-26233)

PDIA0448E

Tool number

: ST35271000 (J-26091)

PDIA0464E

Tool number

: ST22350000 (J-25678-01)

PDIA0450E

RFD-32

REAR FINAL DRIVE ASSEMBLY

Revision: 2006 July

2007 Murano

Install electric controlled coupling to drive pinion.

CAUTION:

●

Align the pin on electric controlled coupling with the
groove of gear carrier.

●

Be careful not to damage center oil seal.

Set AWD solenoid harness guide to gear carrier.

Using the drifts, drive front oil seal until it becomes flush with the
case end.

CAUTION:

●

Do not reuse oil seal.

●

When installing, do not incline oil seal.

●

Apply multi-purpose grease onto oil seal lips, and gear
oil onto the circumference of oil seal.

Apply liquid gasket to mating surface of coupling cover. Overlap
both ends of the bead for at least 3 mm (0.12 in).

●

Use Genuine Silicone RTV or equivalent. Refer to

GI-46,

CAUTION:

Remove old sealant adhering to the mounting surfaces.
Also remove any moisture, oil, or foreign material adhering
to the mounting surfaces.

Install coupling cover to gear carrier with the arrow facing
upward, temporarily tighten reamer bolts to the positions shown
in the figure.

Tighten reamer bolts and coupling cover mounting bolts to the
specified torque. Refer to

RFD-16, "COMPONENTS"

10. Install companion flange.

NOTE:
When reusing electric controlled coupling, align the matching
mark of electric controlled coupling with the matching mark of
companion flange, then install companion flange.

PDIA0463E

Tool number

A: KV38100200 (J-26233)

B: ST27861000 (

—

)

PDIA0449E

PDIA0613E

SDIA0587E

PDIA0455E

REAR FINAL DRIVE ASSEMBLY

RFD-33

RFD

Revision: 2006 July

2007 Murano

11. Install companion flange lock nut using a flange wrench, tighten

to the specified torque. Refer to

RFD-16, "COMPONENTS"

CAUTION:

Do not reuse companion flange lock nut.

12. Check companion flange runout. Refer to

RFD-20, "Companion

Flange Runout"

13. Install connector bracket, and tighten bolts to the specified

torque. Refer to

RFD-16, "COMPONENTS"

PDIA0442E

RFD-34

SERVICE DATA AND SPECIFICATIONS (SDS)

Revision: 2006 July

2007 Murano

SERVICE DATA AND SPECIFICATIONS (SDS)

PFP:00030

General Specifications

NDS0008N

Inspection and Adjustment

NDS0008O

DRIVE GEAR RUNOUT

Unit: mm (in)

DIFFERENTIAL SIDE GEAR CLEARANCE

Unit: mm (in)

PRELOAD TORQUE

Unit: N·m (kg-m, in-lb)

BACKLASH

Unit: mm (in)

COMPANION FLANGE RUNOUT

Unit: mm (in)

SELECTIVE PARTS
Side Gear Thrust Washer

Unit: mm (in)

*: Always check with the Parts Department for the latest parts information.

Applied model

VQ35DE

Final drive model

R145

Gear ratio

2.466

Number of teeth (Drive gear/Drive pinion)

37/15

Oil capacity (Approx.)

(US pt, lmp pt)

0.55 (1-1/8, 1)

Number of pinion gears

Drive pinion adjustment spacer type

Collapsible

Item

Runout limit

Drive gear back face

0.05 (0.0020) or less

Item

Specification

Side gear backlash
(Clearance between side gear and differential case)

0.2 (0.008) or less

(Each gear should rotate smoothly without excessive resistance
during differential motion.)

Item

Specification

Pinion bearing (P

)

0.69 – 1.18 (0.07 – 0.12, 7 – 10)

Side bearing (P

)

0.64 – 0.98 (0.07 – 0.09, 6 – 8)

Side bearing to pinion bearing (Total preload)
(Total preload = P

+ P

)

1.33 – 2.16 (0.14 – 0.22, 12 – 19)

Item

Specification

Drive gear to drive pinion gear

0.10 - 0.15 (0.0039 - 0.0059)

Item

Runout limit

Companion flange face

0.13 (0.0051) or less

Inner side of the companion flange

0.19 (0.0075) or less

Thickness Part

number*

Thickness Part

number*

0.74 (0.0291)
0.77 (0.0303)
0.80 (0.0315)

38424 4N200
38424 4N201
38424 4N202

0.83 (0.0327)
0.86 (0.0339)

38424 4N203
38424 4N204

SERVICE DATA AND SPECIFICATIONS (SDS)

RFD-35

RFD

Revision: 2006 July

2007 Murano

Drive Pinion Adjusting Shim

Unit: mm (in)

*: Always check with the Parts Department for the latest parts information.

Side Bearing Adjusting Shim

Unit: mm (in)

*: Always check with the Parts Department for the latest parts information.

Thickness Part

number*

Thickness Part

number*

1.70 (0.0669)
1.73 (0.0681)
1.76 (0.0693)
1.79 (0.0705)
1.82 (0.0717)
1.85 (0.0728)
1.88 (0.0740)
1.91 (0.0752)
1.94 (0.0764)
1.97 (0.0776)

38154 4N200
38154 4N201
38154 4N202
38154 4N203
38154 4N204
38154 4N205
38154 4N206
38154 4N207
38154 4N208
38154 4N209

2.00 (0.0787)
2.03 (0.0799)
2.06 (0.0811)
2.09 (0.0823)
2.12 (0.0835)
2.15 (0.0846)
2.18 (0.0858)
2.21 (0.0870)
2.24 (0.0882)

38154 4N210
38154 4N211
38154 4N212
38154 4N213
38154 4N214
38154 4N215
38154 4N216
38154 4N217
38154 4N218

Thickness

Part number*

Thickness

Part number*

1.85 (0.0728)
1.90 (0.0748)
1.95 (0.0768)
2.00 (0.0787)

38453 4N200
38453 4N201
38453 4N202
38453 4N203

2.05 (0.0807)
2.10 (0.0827)
2.15 (0.0854)
2.20 (0.0866)

38453 4N204
38453 4N205
38453 4N206
38453 4N207

Nissan Murano Z50 (2007 year). Manual - part 162