Nissan Murano Z50 (2007 year). Manual - part 120

 

  Index      Manuals     Nissan Murano Z50 (2007 year) - Service and Repair Manual

 

Search            copyright infringement  

 

 

 

 

 

 

 

 

Content      ..     118      119      120      121     ..

 

 

Nissan Murano Z50 (2007 year). Manual - part 120

 

 

GW-44

POWER WINDOW SYSTEM

Revision: 2006 July

2007 Murano

Check Front Power Window Motor (Passenger Side) Circuit

NIS001BD

1. 

CHECK FRONT POWER WINDOW SWITCH (PASSENGER SIDE) OUTPUT SIGNAL

1.

Turn igniting switch ON.

2.

Check voltage between front power window switch (passenger side) connector and ground.

OK or NG

OK

>> GO TO 2.

NG

>> Replace front power window switch (passenger side).

2. 

CHECK HARNESS CONTINUITY

1.

Turn ignition switch OFF.

2.

Disconnect front power window switch (passenger side) and front power window motor (passenger side)
connector.

3.

Check continuity between front power window switch (passen-
ger side) connector D35 terminals 8,9 and front power window
motor (passenger side) connector D36 terminals 1, 2.

OK or NG

OK

>> Replace front power window motor (passenger side).

NG

>> Repair or replace harness.

Check Rear Power Window Motor (LH) Circuit

NIS001BE

1. 

CHECK REAR POWER WINDOW SWITCH (LH) OUTPUT SIGNAL

1.

Turn ignition switch OFF.

2.

Disconnect rear power window motor (LH).

3.

Turn ignition switch ON.

4.

Check voltage between rear power window motor (LH) connector and ground.

OK or NG

OK

>> Replace rear power window motor (LH).

NG

>> GO TO 2.

Connector

Terminals (Wire color)

Condition

Voltage (V)

(Approx.)

(+)

(-)

D35

8 (L)

Ground

Closing

Battery voltage

Opening

9 (G)

Closing

0

Opening

Battery voltage 

PIIA4182E

8 (L) – 2 (L)

: Continuity should exist.

9 (G) – 1 (G)

: Continuity should exist.

PIIA9659E

Connector

Terminals (Wire color)

Condition

Voltage (V)

(Approx.)

(+)

(-)

D52

1 (G)

Ground

Closing

0

Opening

Battery voltage

2 (L)

Closing

Battery voltage

Opening

0

PIIA9660E

POWER WINDOW SYSTEM

GW-45

C

D

E

F

G

H

J

K

L

M

A

B

GW

Revision: 2006 July

2007 Murano

2. 

CHECK HARNESS CONTINUITY 1

1.

Turn ignition switch OFF.

2.

Disconnect rear power window switch (LH) connector.

3.

Check continuity between rear power window switch (LH) con-
nector D55 terminal 4, 5 and rear power window motor (LH) con-
nector D52 terminals 1, 2.

OK or NG

OK

>> GO TO 3.

NG

>> Repair or replace harness.

3. 

CHECK REAR POWER WINDOW SWITCH (LH) POWER SUPPLY 

1.

Connect rear power window switch (LH) connector.

2.

Turn ignition switch ON.

3.

Check voltage between rear power window switch (LH) connec-
tor D55 terminal 1 and ground.

OK or NG

OK

>> GO TO 4.

NG

>> Repair or replace harness.

4. 

CHECK REAR POWER WINDOW SWITCH LH 

1.

Turn igniting switch OFF.

2.

Disconnect rear power window switch (LH) connector.

3.

Check continuity between rear power window switch (LH) connector D55 terminals 1, 2, 3 and 4, 5.

OK or NG

OK

>> GO TO 5.

NG

>> Replace rear power window switch (LH).

4 (G) – 1 (G)

: Continuity should exist.

5 (L) – 2 (L)

: Continuity should exist.

PIIA9661E

1 (W/L) – Ground

: Battery voltage

PIIA4185E

Terminal

Switch condition

Continuity 

1

4

DOWN position

Yes

3

Free

1

5

UP position

2

Free

PIIA4186E

GW-46

POWER WINDOW SYSTEM

Revision: 2006 July

2007 Murano

5. 

CHECK HARNESS CONTINUITY 

1.

Disconnect power window main switch connector.

2.

Check continuity between power window main switch connector
D6 terminals 1, 3 and rear power window switch (LH) connector
D55 terminals 2, 3.

OK or NG

OK

>> GO TO 6.

NG

>> Repair or replace harness.

6. 

CHECK POWER WINDOW MAIN SWITCH OUTPUT SINGAL

1.

Connect BCM connector.

2.

Turn ignition switch ON.

3.

Power window main switch is operated, check voltage between power window main switch connector and
ground.

OK or NG

OK

>> Check the condition of the harness and the connector.

NG

>> Replace power window main switch.

Check Rear Power Window Motor (RH) Circuit 

NIS001BF

1. 

CHECK REAR POWER WINDOW SWITCH (RH) OUTPUT SIGNAL

1.

Turn ignition switch OFF.

2.

Disconnect rear power window motor (RH).

3.

Turn ignition switch ON.

4.

Check voltage between rear power window motor (RH) connector and ground.

OK or NG

OK

>> Replace rear power window motor (RH).

NG

>> GO TO 2.

1 (L) – 2 (Y/B)

: Continuity should exist.

3 (R/Y) – 3 (R)

: Continuity should exist.

PIIA4188E

Connector

Terminals (Wire color)

Condition

Voltage (V)

(Approx.)

(+)

(-)

D6

1 (L)

Ground

Closing

Battery voltage

Opening

0

3 (R/Y)

Closing

0

Opening

Battery voltage

PIIA4187E

Connector

Terminals (Wire color)

Condition

Voltage (V)

(Approx.)

(+)

(-)

D72

1 (G)

Ground

Closing

0

Opening

Battery voltage

2 (L)

Closing

Battery voltage

Opening

0

PIIA9660E

POWER WINDOW SYSTEM

GW-47

C

D

E

F

G

H

J

K

L

M

A

B

GW

Revision: 2006 July

2007 Murano

2. 

CHECK HARNESS CONTINUITY 1

1.

Turn ignition switch OFF.

2.

Disconnect rear power window switch (RH) connector.

3.

Check continuity between rear power window switch (RH) con-
nector D75 terminals 4, 5 and rear power window motor (RH)
connector D72 terminal 1, 2.

OK or NG

OK

>> GO TO 3.

NG

>> Repair or replace harness.

3. 

CHECK REAR POWER WINDOW SWITCH (RH) POWER SUPPLY 

1.

Connect rear power window switch (RH) connector.

2.

Turn ignition switch ON.

3.

Check voltage between rear power window switch (RH) connec-
tor D75 terminal 1 and ground.

OK or NG

OK

>> GO TO 4.

NG

>> Repair or replace harness.

4. 

CHECK REAR POWER WINDOW SWITCH (RH) 

1.

Turn ignition switch OFF.

2.

Disconnect rear power window switch (RH) connector.

3.

Check continuity between rear power window switch (RH) con-
nector D75 terminal 1, 2, 3 and 4, 5.

OK or NG

OK

>> GO TO 5.

NG

>> Replace rear power window switch (RH).

4 (G) – 1 (G)

: Continuity should exist.

5 (L) – 2 (L)

: Continuity should exist.

PIIA9661E

1 (W/L) – Ground

: Battery voltage

PIIA4185E

Terminal

Switch condition

Continuity 

1

4

DOWN position

Yes

3

Free

1

5

UP position

2

Free

PIIA4186E

GW-48

POWER WINDOW SYSTEM

Revision: 2006 July

2007 Murano

5. 

CHECK HARNESS CONTINUITY 

1.

Disconnect power window main switch connector.

2.

Check continuity between power window main switch connector
D6 terminal 5, 7 and rear power window switch (RH) connector
D75 terminal 2, 3.

OK or NG

OK

>> GO TO 6.

NG

>> Repair or replace harness.

6. 

CHECK POWER WINDOW MAIN SWITCH OUTPUT SINGAL

1.

Connect BCM connector.

2.

Turn ignition switch ON.

3.

Power window main switch is operated, check voltage between power window main switch connector and
ground.

OK or NG

OK

>> Check the condition of the harness and the connector.

NG

>> Replace power window main switch.

Check Limit Switch Circuit (Driver Side) 

NIS001BG

1. 

CHECK DRIVER DOOR MAIN SWITCH LIMIT SIGNAL

1.

Turn ignition switch ON.

2.

Check voltage between front power window motor (driver side) connector and ground.

OK or NG

OK

>> Limit switch circuit is OK.

NG

>> GO TO 2. 

5 (R) – 3 (R)

: Continuity should exist.

7 (Y/B) – 2 (Y/B)

: Continuity should exist.

PIIA4190E

Connector

Terminals (Wire color)

Condition

Voltage (V)

(Approx.)

(+)

(-)

D6

5 (R)

Ground

Closing

0

Opening

Battery voltage

7 (Y/B)

Closing

Battery voltage

Opening

0

PIIA4189E

Connector

Terminals (Wire color)

Condition Voltage 

(V)

(Approx.)

(+)

(-)

D8

5 (G/W)

Ground

Driver side door window is 
between fully-open and just 
before fully-closed position 
(ON)

0

Driver side door window is 
between just before fully-
closed position and fully-
closed position (OFF)

5

PIIA9662E

POWER WINDOW SYSTEM

GW-49

C

D

E

F

G

H

J

K

L

M

A

B

GW

Revision: 2006 July

2007 Murano

2. 

CHECK GROUND CIRCUIT 

1.

Turn ignition switch OFF.

2.

Disconnect front power window motor (driver side) connector.

3.

Check continuity between front power window motor (driver
side) connector D8 terminal 6 and ground.

OK or NG

OK

>> GO TO 4.

NG

>> GO TO 3.

3. 

CHECK HARNESS CONTINUITY 1

1.

Disconnect power window main switch connector.

2.

Check continuity between power window main switch connector
D6 terminal 2 and front power window motor (driver side) con-
nector D8 terminal 6.

OK or NG

OK

>> Replace power window main switch.

NG

>> Repair or replace harness.

4. 

CHECK HARNESS CONTINUITY 2

1.

Disconnect power window main switch connector.

2.

Check continuity between power window main switch connector
D6 terminal 9 and front power window motor (driver side) con-
nector D8 terminal 5. 

OK or NG

OK

>> GO TO 5.

NG

>> Repair or replace harness.

6 (W/B) – Ground

: Continuity should exist.

PIIA9663E

2 (W/B) – 6 (W/B)

: Continuity should exist.

PIIB0420E

9 (G/W) – 5 (G/W)

: Continuity should exist.

PIIA9665E

GW-50

POWER WINDOW SYSTEM

Revision: 2006 July

2007 Murano

5. 

CHECK POWER WINDOW MAIN SWITCH OUTPUT SIGNAL

1.

Connect power window main switch connector.

2.

Turn ignition switch ON.

3.

Check voltage between power window main switch connector
D6 terminal 9 and ground.

OK or NG

OK

>> GO TO 6.

NG

>> Replace power window main switch.

6. 

CHECK LIMIT SWITCH

1.

Connect power window main switch and front power window motor (driver side) connector.

2.

Turn ignition switch ON.

3.

Check continuity between front power window motor (driver
side) connector D8 terminals 5 and 6.

*: When checking continuity, turn ignition switch OFF.

OK or NG

OK

>> Check the condition of the harness and the connector.

NG

>> Replace front power window motor (driver side).

Check Limit Switch Circuit (Passenger Side)

NIS001BH

1. 

CHECK FRONT POWER WINDOW SWITCH (PASSENGER SIDE) LIMIT SIGNAL

1.

Turn ignition switch ON.

2.

Check voltage between front power window motor (passenger side) connector and ground.

OK or NG

OK

>> Limit switch circuit is OK.

NG

>> GO TO 2.

9 (G/W) – Ground

: Approx. 5V

PIIA4194E

Connector

Terminals (Wire color)

Condition 

Continuity

D8

5 (G/W)

6 (W/B)

Driver side door window is 
between fully-open and just 
before fully-closed position 
(ON)

Yes*

Driver side door window is 
between just before fully-
closed position and fully-
closed position (OFF)

No*

PIIA9666E

Connector

Terminals (Wire color)

Condition 

Voltage (V)

(Approx.)

(+)

(-)

D36

5 (G/W)

Ground

Passenger side door window 
is between fully-open and 
just before fully-closed posi-
tion (ON)

0

Passenger side door window 
is between just before fully-
closed position and fully-
closed position (OFF)

5

PIIA9667E

POWER WINDOW SYSTEM

GW-51

C

D

E

F

G

H

J

K

L

M

A

B

GW

Revision: 2006 July

2007 Murano

2. 

CHECK GROUND CIRCUIT 

1.

Turn ignition switch OFF.

2.

Disconnect front power window motor (passenger side) connector.

3.

Check continuity between front power window motor (passenger
side) connector D36 terminal 6 and ground.

OK or NG

OK

>> GO TO 4.

NG

>> GO TO 3.

3. 

CHECK HARNESS CONTINUITY 1

1.

Disconnect front power window switch (passenger side) connector.

2.

Check continuity between front power window switch (passen-
ger side) connector D35 terminal 3 and front power window
motor (passenger side) connector D36 terminal 6.   

OK or NG

OK

>> Replace front power window switch (passenger side).

NG

>> Repair or replace harness.

4. 

CHECK HARNESS CONTINUITY 2

1.

Disconnect front power window switch (passenger side) connector.

2.

Check continuity between front power window switch (passen-
ger side) connector D35 terminal 15 and front power window
motor (passenger side) connector D36 terminal 5.

OK or NG

OK

>> GO TO 5.

NG

>> Repair or replace harness.

6 (W/B) – Ground

: Continuity should exist.

PIIA9668E

3 (W/B) – 6 (W/B)

: Continuity should exist.

PIIA9669E

15 (G/W) – 5 (G/W)

: Continuity should exist.

PIIA9670E

GW-52

POWER WINDOW SYSTEM

Revision: 2006 July

2007 Murano

5. 

CHECK FRONT POWER WINDOW SWITCH (PASSENGER SIDE) OUTPUT SIGNAL

1.

Connect front power window switch (passenger side) connector.

2.

Turn ignition switch ON.

3.

Check voltage between front power window switch (passenger
side) connector D35 terminal 15 and ground.

OK or NG

OK

>> GO TO 6.

NG

>> Replace front power window switch (passenger side).

6. 

CHECK LIMIT SWITCH

1.

Connect front power window motor (passenger side) and front power window switch (passenger side)
connector.

2.

Turn ignition switch ON.

3.

Check continuity between front power window motor (passenger
side) connector D36 terminals 5 and 6.

*: When checking continuity, turn ignition switch OFF.

OK or NG

OK

>> Check the condition of the harness and the connector.

NG

>> Replace front power window motor (passenger side).

Check Encoder Circuit (Driver Side)

NIS001BI

1. 

CHECK FRONT POWER WINDOW MOTOR (DRIVER SIDE) POWER SUPPLY

1.

Turn ignition switch ON.

2.

Check voltage between front power window motor (driver side)
connector D8 terminal 4 and ground.

OK or NG

OK

>> GO TO 3.

NG

>> GO TO 2.

15 (G/W) – Ground

: Approx. 5V

PIIA4200E

Connector

Terminals (Wire color)

Condition 

Continuity

D36

5 (G/W)

6 (W/B)

Passenger side door window 
is between fully-open and 
just before fully-closed posi-
tion (ON)

Yes*

Passenger side door window 
is between just before fully-
closed position and fully-
closed position (OFF)

No*

PIIA9671E

4 (G/R) – Ground

: Approx.10V

PIIA9672E

POWER WINDOW SYSTEM

GW-53

C

D

E

F

G

H

J

K

L

M

A

B

GW

Revision: 2006 July

2007 Murano

2. 

CHECK HARNESS CONTINUITY 1

1.

Turn ignition switch OFF.

2.

Disconnect front power window motor (driver side) and power window main switch.

3.

Check continuity between power window main switch connector
D6 terminal 15 and front power window motor (driver side) con-
nector D8 terminal 4.

OK or NG

OK

>> Replace power window main switch.

NG

>> Repair or replace harness.

3. 

CHECK GROUND CIRCUIT

1.

Turn ignition switch OFF.

2.

Disconnect front power window motor (driver side) connector.

3.

Check continuity between front power window motor (driver
side) connector D8 terminal 6 and round.

OK or NG

OK

>> GO TO 5.

NG

>> GO TO 4.

4. 

CHECK HARNESS CONTINUITY 2

1.

Disconnect power window main switch connector.

2.

Check continuity between power window main switch connector
D6 terminal 2 and front power window motor (driver side) con-
nector D8 terminal 6.

OK or NG

OK

>> Replace power window main switch.

NG

>> Repair or replace harness.

15 (G/R) – 4 (G/R)

: Continuity should exist.

PIIA9673E

6 (W/B) – Ground

: Continuity should exist.

PIIA9663E

2 (W/B) – 6 (W/B)

: Continuity should exist.

PIIB0420E

GW-54

POWER WINDOW SYSTEM

Revision: 2006 July

2007 Murano

5. 

CHECK ENCODER SIGNAL

1.

Connect front power window motor (driver side) connector.

2.

Turn ignition switch ON.

3.

Check the signal between power window main switch connector and ground with oscilloscope.

OK or NG

OK

>> Replace power window main switch.

NG

>> GO TO 6.

6. 

CHECK HARNESS CONTINUITY 3

1.

Turn ignition switch OFF.

2.

Disconnect power window main switch and front power window motor (driver side)  connector.

3.

Check continuity between power window main switch connector
D6 terminal 13 and front power window motor (driver side) con-
nector D8 terminal 3.

OK or NG

OK

>> Replace front power window motor (driver side)

NG

>> Repair or replace harness.

Check Encoder Circuit (Front Passenger Side)

NIS001BJ

1. 

CHECK FRONT POWER WINDOW MOTOR (PASSENGER SIDE) POWER SUPPLY

1.

Turn ignition switch ON.

2.

Check voltage between front power window motor (passenger
side) connector D36 terminal 4 and  ground.

OK or NG

OK

>> GO TO 3.

NG

>> GO TO 2.

Connector

Terminals (Wire color)

Condition

Signal

(Reference value)

(+)

(-)

D6

13 (G/Y)

Ground

opening

PIIA4205E

OCC3383D

13 (G/Y) – 3 (G/Y)

: Continuity should exist.

PIIA9674E

4 (G/R) – Ground

: Approx. 10V

PIIA9675E

POWER WINDOW SYSTEM

GW-55

C

D

E

F

G

H

J

K

L

M

A

B

GW

Revision: 2006 July

2007 Murano

2. 

CHECK HARNESS CONTINUITY 1

1.

Turn ignition switch OFF.

2.

Disconnect front power window switch (passenger side) connector and front power window motor (pas-
senger side) connector.

3.

Check continuity between front power window switch (passen-
ger side) connector D35 terminal 4 and  front power window
motor (passenger side) connector D36 terminal 4.

OK or NG

OK

>> Replace front power window switch (passenger side).

NG

>> Repair or replace harness.

3. 

CHECK GROUND CIRCUIT

1.

Turn ignition switch OFF.

2.

Disconnect front power window motor (passenger side) connector.

3.

Check continuity between front power window motor (passenger
side) connector D36 terminal 6 and   ground.

OK or NG

OK

>> GO TO 5.

NG

>> GO TO 4.

4. 

CHECK HARNESS CONTINUITY 2

1.

Disconnect front power window switch (passenger side) connector.

2.

Check continuity between front power window switch (passen-
ger side) connector D35 terminal 3 and front power window
motor (passenger side) connector D36 terminal 6.

OK or NG

OK

>> Replace front power window switch (passenger side).

NG

>> Repair or replace harness.

4 (G/R) – 4 (G/R)

: Continuity should exist.

PIIA9676E

6 (W/B) – Ground

: Continuity should exist.

PIIA9668E

3 (W/B) – 6 (W/B)

: Continuity should exist.

PIIA9669E

GW-56

POWER WINDOW SYSTEM

Revision: 2006 July

2007 Murano

5. 

CHECK ENCODER SIGNAL

1.

Connect front power window motor (passenger side) connector.

2.

Turn ignition switch ON.

3.

Check the signal between front power window switch (passenger side) connector and ground with oscillo-
scope.

OK or NG

OK

>> Replace front power window switch (passenger side).

NG

>> GO TO 6.

6. 

CHECK HARNESS CONTINUITY 3

1.

Turn ignition switch OFF.

2.

Disconnect front power window switch (passenger side) and front power window motor (passenger side)
connector.

3.

Check continuity between front power window switch (passen-
ger side) connector D35 terminal 12 and front power window
motor (passenger side) connector D36 terminal 3.

OK or NG

OK

>> Replace front power window motor (passenger side).

NG

>> Repair or replace harness.

Connec-

tor

Terminals (Wire color)

Condition

Signal

(Reference value)

(+)

(-)

D35

12 (G/Y)

Ground

opening

PIIA4209E

OCC3383D

12 (G/Y) – 3 (G/Y)

: Continuity should exist.

PIIA9677E

POWER WINDOW SYSTEM

GW-57

C

D

E

F

G

H

J

K

L

M

A

B

GW

Revision: 2006 July

2007 Murano

Check Door Switch

NIS001BK

1. 

CHECK DOOR SWITCH INPUT SIGNAL 1

 With CONSULT-II

Check door switches (“DOOR SW-DR” and “DOOR SW-AS”) in “DATA MONITOR” mode with CONSULT-II.

Without CONSULT-II

Check voltage between BCM connector and ground.

* : without intelligent key

OK or NG

OK

>> Door switch is OK. 

NG

>> GO TO 2.

Monitor item

Condition

DOOR SW-DR

OPEN

: ON

CLOSE

: OFF

DOOR SW-AS

OPEN

: ON

CLOSE

: OFF

PIIA2464E

Item

Con-

nector

Terminals (Wire color)

Condition

Voltage (V)

(Approx.)

(+)

(-)

Passenger 

side

M34

12

 (R/G or R*)

Ground

OPEN

0

CLOSE

Battery voltage

Driver

side

M36

62 (SB)

OPEN

0

CLOSE

Battery voltage

PIIA6158E

GW-58

POWER WINDOW SYSTEM

Revision: 2006 July

2007 Murano

2. 

CHECK HARNESS CONTINUITY

1.

Turn ignition switch OFF.

2.

Disconnect BCM and front door lock assembly (driver and passenger side) connector.

3.

Check continuity between BCM connector M34, 36 terminals 12, 62 and front door lock assembly connec-
tor D10 (driver side), D38 (passenger side) terminal 4.

4.

Check continuity between BCM connector M34, 36 terminals 12,
62 and ground.

OK or NG

OK

>> GO TO 3.

NG

>> Repair or replace harness.

3. 

CHECK DOOR SWITCH

Check continuity between front door lock assembly terminals 4 and
5.

OK or NG

OK

>> GO TO 4.

NG

>> Replace malfunction front door lock assembly.

4. 

CHECK DOOR SWITCH GROUND CIRCUIT

Check continuity between front door lock assembly connector D10
(driver side), D38 (passenger side) terminal 5 and ground.

OK or NG

OK

>> GO TO 5.

NG

>> Repair or replace harness.

Driver side

62 (SB) – 4 (SB)

: Continuity should exist.

Passenger side

12 (R/G) – 4 (R/G)

: Continuity should exist.

12 (R/G) – Ground

: Continuity should not exist.

62 (SB) – Ground

: Continuity should not exist.

PIIB0907E

Terminal

Door switch

Continuity

4

5

OPEN

No

CLOSE

Yes

PIIA4220E

5 (B) – Ground

: Continuity should exist.

PIIA9680E

POWER WINDOW SYSTEM

GW-59

C

D

E

F

G

H

J

K

L

M

A

B

GW

Revision: 2006 July

2007 Murano

5. 

CHECK BCM OUTPUT SIGNAL

1.

Connect BCM connector.

2.

Check voltage between BCM connector M3, B14 terminals 12,
62 and ground.

OK or NG

OK

>> Check the condition of the harness and the connector.

NG

>> Replace BCM.

Check Door Key Cylinder Switch/Without Intelligent Key 

NIS001BL

1. 

CHECK DOOR KEY CYLINDER SWITCH INPUT SIGNAL

 With CONSULT-II

Check door key cylinder switch (“KEY CYL LK SW”, “KEY CYL UN SW”) in “DATA MONITOR” mode with
CONSULT-II.

 Without CONSULT-II

Check voltage between power window main switch connector and ground.

OK or NG

OK

>> Check the condition of the harness and the connector.

NG

>> GO TO 2.

12 (R/G) – Ground

: Battery voltage

62 (SB) – Ground

: Battery voltage

PIIA6158E

Monitor item

Condition

KEY CYL LK-SW

Lock

: ON

Neutral / Unlock

: OFF

KEY CYL UN-SW

Unlock

: ON

Neutral / Lock

: OFF

PIIA6285E

Connector

Terminals (Wire color)

Key position 

Voltage (V) 

(Approx.)

(+)

(–)

D6

4 (L)

Ground

Lock

0

Neutral / Unlock

5

6 (R)

Unlock

0

Neutral / Lock

5

PIIA4211E

 

 

 

 

 

 

 

Content      ..     118      119      120      121     ..