Nissan Murano Z50 (2006 year). Manual - part 209

 

  Index      Manuals     Nissan Murano Z50 (2006 year) - Service and Repair Manual

 

Search            copyright infringement  

 

 

 

 

 

 

 

 

Content      ..     207      208      209      210     ..

 

 

Nissan Murano Z50 (2006 year). Manual - part 209

 

 

TROUBLE DIAGNOSIS FOR SYMPTOMS

WT-47

C

D

F

G

H

I

J

K

L

M

A

B

WT

Revision: 2006 August

2006 Murano

Low Tire Pressure Warning Lamp Stays ON When Ignition Switch Is Turned ON

NES000EF

DIAGNOSTIC PROCEDURE

1. 

CHECK SYSTEM FOR BCM

Perform self-diagnosis. Refer to 

WT-24, "Self-Diagnostic Procedure"

 .

Does self-diagnostic results indicate any malfunctions?

YES

>> Perform trouble diagnosis. Refer to 

WT-21, "SELF-DIAG RESULT MODE"

 .

NO

>> GO TO 2.

2. 

CHCEK ID REGISTRATION

Perform ID registration all transmitters. Refer to 

WT-26, "ID Registration Procedure"

 .

Does low tire pressure warning lamp turn OFF?

YES

>> INSPECTION END

NO

>> GO TO 3.

3. 

CHECK POWER SUPPLY

1.

Turn ignition switch “OFF”.

2.

Disconnect BCM harness connector.

3.

Check voltage between BCM harness connector terminals and ground.

4.

Turn ignition switch “ON”. (Do not start engine.)

5.

Check voltage between BCM harness connector terminals and ground.

OK or NG

OK

>> GO TO 4.

NG

>> Check the following. If any items are damaged, repair or replace damaged parts.

50 A fuses [No. F located in the fuse block (J/B)]. Refer to 

PG-3, "POWER SUPPLY ROUTING

CIRCUIT"

 .

10 A fuses [No. 1, 18 located in the fuse block (J/B)]. Refer to 

PG-3, "POWER SUPPLY ROUT-

ING CIRCUIT"

 .

Harness for short or open between battery and BCM harness connector M35 terminals 42 and
55.

Harness for short or open between ignition switch and BCM harness connector M34 terminal
38.

Battery and ignition switch. Refer to 

PG-3, "POWER SUPPLY ROUTING CIRCUIT"

 .

Connector

Terminal

Voltage (Approx.)

M34

38 - Ground

0 V

M35

42 - Ground

Battery voltage

55 - Ground

Connector

Terminal

Voltage (Approx.)

M34

38 - Ground

Battery voltage

M35

42 - Ground

55 - Ground

WT-48

TROUBLE DIAGNOSIS FOR SYMPTOMS

Revision: 2006 August

2006 Murano

4. 

CHECK GROUND CIRCUIT

1.

Turn ignition switch “OFF”.

2.

Disconnect BCM harness connector.

3.

Check continuity between BCM harness connector M35 terminal
52.

Also check harness for short to power.

OK or NG

OK

>> GO TO 5.

NG

>> Repair open circuit or short to power in harness or con-

nectors.

5. 

CHECK SYMPTOM

Check again.

OK or NG

OK

>> INSPECTION END

NG

>> GO TO 6.

6. 

CHECK BCM

Check BCM input/output signal. Refer to 

WT-18, "BCM Input/Output Signal Reference Values"

 .

OK or NG

OK

>> GO TO 5.

NG

>> Check BCM pin terminals for damage or loose connection with harness connector. If any items

are damaged, repair or replace damaged parts. Replace BCM. Refer to 

BCS-14, "Removal and

Installation of BCM"

 .

Continuity should exist.

SEIA0437E

TROUBLE DIAGNOSIS FOR SYMPTOMS

WT-49

C

D

F

G

H

I

J

K

L

M

A

B

WT

Revision: 2006 August

2006 Murano

Low Tire Pressure warning Lamp Blinks When Ignition Switch Is Turned ON

NES000EG

SYMPTOM:

If warning lamp blinks below, the system is normal.

Blink Mode A

This mode shows transmitter status is OFF-mode.
Perform transmitter wake up operation. Refer to 

WT-28, "Trans-

mitter Wake Up Operation"

 .

DIAGNOSTIC PROCEDURE

1. 

CHECK TIRE PRESSURE WARNIG CHECK SWITCH

1.

Turn ignition switch “OFF”.

2.

Disconnect BCM harness connectors.

3.

Check continuity between BCM harness connector M34 terminal
15 and ground.

Also check harness for short to ground.

OK or NG

OK

>> GO TO 2.

NG

>> Repair short to ground in harness or connector.

2. 

CHECK SYMPTOM

Check again.

OK or NG

OK

>> INSPECTION END

NG

>> GO TO 3.

3. 

CHECK BCM

Check BCM input/output signal. Refer to 

WT-18, "BCM Input/Output Signal Reference Values"

 .

OK or NG

OK

>> GO TO 2.

NG

>> Check BCM pin terminals for damage or loose connection with harness connector. If any items

are damaged, repair or replace damaged parts. Replace BCM. Refer to 

BCS-14, "Removal and

Installation of BCM"

 .

SEIA0347E

Continuity should not exist.

SEIA0438E

WT-50

TROUBLE DIAGNOSIS FOR SYMPTOMS

Revision: 2006 August

2006 Murano

Turn Signal Lamp Blinks When Ignition Switch Is Turned ON

NES000EH

DIAGNOSTIC PROCEDURE

1. 

CHECK TIRE PRESSURE WARNING CHECK SWITCH CIRCUIT

1.

Turn ignition switch “OFF”.

2.

Disconnect BCM harness connector.

3.

Check continuity between BCM harness connector M34 terminal
15 and ground.

Also check harness for short to ground.

OK or NG

OK

>> GO TO 2.

NG

>> Repair short to ground in harness or connector.

2. 

CHECK SYMPTOM

Check again.

OK or NG

OK

>> INSPECTION END

NG

>> Check turn signal lamp operation. Refer to 

LT-114, "System Description"

 .

ID Registration Cannot Be Completed

NES000EI

DIAGNOSTIC PROCEDURE

1. 

ID REGISTRATION

Perform ID registration of all transmitters. Refer to 

WT-26, "ID Registration Procedure"

 .

Can ID registration of all transmitters be completed?

YES

>> GO TO 2.

NO

>> GO TO 3.

2. 

CHECK SYMPTOM

Check again.

OK or NG

OK

>> INSPECTION END

NG

>> GO TO 3.

3. 

CHECK TRANSMITTER CIRCUIT

Perform trouble diagnosis for transmitter circuit. Refer to 

WT-32, "TROUBLE DIAGNOSIS FOR SYSTEM"

 .

OK or NG

OK

>> INSPECTION END

NG

>> GO TO 2.

Continuity should not exist.

SEIA0438E

TRANSMITTER

WT-51

C

D

F

G

H

I

J

K

L

M

A

B

WT

Revision: 2006 August

2006 Murano

TRANSMITTER

PFP:40700

Removal and Installation

NES000EJ

REMOVAL

1.

Deflate tire. Unscrew transmitter retaining nut and allow transmitter to fall into tire.

2.

Gently bounce tire so that transmitter falls to bottom of tire.
Place on tire changing machine and break both tire beads
ensuring that the transmitter remains at the bottom of the tire.

3.

Turn tire so that valve hole is at bottom and bounce so that
transmitter is near valve hole. Carefully lift tire onto turntable and
position valve hole (and transmitter) 270 degree from mounting/
dismounting head.

4.

Lubricate tire well and remove first side of the tire. Reach inside
the tire and remove the transmitter.

INSTALLATION

1.

Put first side of tire onto rim.

2.

Mount transmitter on rim and tighten nut.

CAUTION:

Speed for tightening nut should be less than 40 rpm.

SEIA0047E

SEIA0048E

SEIA0049E

SEIA0521E

WT-52

TRANSMITTER

Revision: 2006 August

2006 Murano

3.

Place wheel on turntable of tire machine. Ensure that transmitter
is 270 degree from mounting head when second side of tire is
fitted. 

NOTE:
Do not touch transmitter at mounting head.

4.

Lubricate tire well and fit second side of tire as normal. Ensure
that tire does not rotate relative to rim.

5.

Inflate tire and fit to appropriate wheel position.

SEIA0048E

ROAD WHEEL

WT-53

C

D

F

G

H

I

J

K

L

M

A

B

WT

Revision: 2006 August

2006 Murano

ROAD WHEEL

PFP:40300

Inspection

NES000EV

ALUMINUM WHEEL

1.

Check tires for wear and improper inflation.

2.

Check wheels for deformation, cracks and other damage. If deformed, remove wheel and check wheel
runout.

a.

Remove tire from aluminum wheel and mount on a tire balance machine.

b.

Set dial indicator as shown in the illustration.

c.

If the total runout value exceeds the limit, replace aluminum
wheel.

STEEL WHEEL (FOR EMERGENCY USE)

1.

Check tires for wear and improper inflation.

2.

Check wheels for deformation, cracks and other damage. If deformed, remove wheel and check wheel
runout.

a.

Remove tire from steel wheel and mount wheel on a tire balance machine.

b.

Set two dial indicators as shown in the illustration.

c.

Set each dial indicator to “0”.

d.

Rotate wheel and check dial indicators at several points around
the circumference of the wheel.

e.

Calculate runout at each point as shown below.

f.

Select maximum positive runout value and the maximum nega-
tive value. Add the two values to determine total runout.

CAUTION:

In case a positive or negative value is not available, use the
maximum value (negative or positive) for total runout.

g.

If the total runout value exceeds the limit, replace steel wheel.

Lateral runout limit (A)

: 0.3 mm (0.012 in)

Radial runout limit (B)

: 0.3 mm (0.012 in)

SEIA0737E

Lateral runout limit (A)

: (

+

)/2

Radial runout limit (B)

: (

+

)/2

Lateral runout limit (A)

: 1.5 mm (0.059 in)

Radial runout limit (B)

: 1.5 mm (0.059 in)

SEIA0738E

WT-54

ROAD WHEEL TIRE ASSEMBLY

Revision: 2006 August

2006 Murano

ROAD WHEEL TIRE ASSEMBLY

PFP:40300

Balancing Wheels (Bonding Weight Type)

NES000EW

REMOVAL

1.

Remove inner and outer balance weights from the road wheel.

CAUTION:

Be careful not to scratch the road wheel during removal.

2.

Using releasing agent, remove double-faced adhesive tape from the road wheel.

CAUTION:

Be careful not to scratch the road wheel during removal.

After removing double-faced adhesive tape, wipe clean traces of releasing agent from the road
wheel.

WHEEL BALANCE ADJUSTMENT 

If a tire balance machine has adhesion balance weight mode settings and drive-in weight mode setting,
select and adjust a drive-in weight mode suitable for road wheels.

1.

Set road wheel on wheel balancer using the center hole as a guide. Start the tire balance machine.

2.

When inner and outer unbalance values are shown on the wheel balancer indicator, multiply outer unbal-
ance value by 5/3 to determine balance weight that should be used. Select the outer balance weight with
a value closest to the calculated value above and install it to the designated outer position of, or at the
designated angle in relation to the road wheel.

CAUTION:

Do not install the inner balance weight before installing the outer balance weight.

Before installing the balance weight, be sure to clean the
mating surface of the road wheel.

a.

Indicated unbalance value 

×

 5/3 = balance weight to be installed

Calculation example:
23 g (0.81 oz) 

×

 5/3 = 38.33 g (1.35 oz) = 40 g (1.41 oz) balance

weight (closer to calculated balance weight value)

NOTE:
Note that balance weight value must be closer to the calculated
balance weight value.
Example:
37.4 = 35 g (1.23 oz)
37.5 = 40 g (1.41 oz)

SMA054D

ROAD WHEEL TIRE ASSEMBLY

WT-55

C

D

F

G

H

I

J

K

L

M

A

B

WT

Revision: 2006 August

2006 Murano

b.

Install balance weight in the position shown in the figure at left.

c.

When installing balance weight to road wheels, set it into the
grooved area on the inner wall of the road wheel as shown in the
figure so that the balance weight center is aligned with the wheel
balancer indication position (angle).

CAUTION:

Always use genuine Nissan adhesion balance weights.

Balance weights are non-reusable; always replace with
new ones.

Do not install more than three sheets of balance weight.

d.

If calculated balance weight value exceeds 50 g (1.76 oz), install
two balance weight sheets in line with each other (as shown in
the figure).

CAUTION:

Do not install one balance weight sheet on top of another.

3.

Start wheel balancer again.

4.

Install drive-in balance weight on inner side of road wheel in the
wheel balancer indication position (angle).

CAUTION:

Do not install more than two balance weights.

5.

Start wheel balancer. Make sure that inner and outer residual
unbalance values are 5 g (0.17 oz) each or below.

6.

If either residual unbalance value exceeds 5 g (0.17 oz), repeat installation procedures.

Tire Rotation

NES000EX

1.

Follow the maintenance schedule for tire rotation service intervals. Refer to 

MA-6, "Introduction of Peri-

odic Maintenance"

 .

2.

Do not include the spare tire when rotating the tires.

3.

When installing the wheel, tighten wheel nuts to the specified torque.

CAUTION:

When installing wheels, tighten them diagonally by dividing the work two to three times in order
to prevent the wheels from developing any distortion.

Be careful not to tighten wheel nut at torque exceeding the criteria for preventing strain of disc
rotor.

4.

Perform the ID registration, after tire rotation. Refer to 

WT-26, "ID Registration Procedure"

 .

SEIA0271E

Wheel balance

Dynamic (At rim flange)

Static

Maximum allowable 
unbalance

5 g (0.17 oz) (one side)

10 g (0.35 oz)

SMA056D

Wheel nuts

: 108 N·m (11 kg-m, 80 ft-lb)

WT-56

SERVICE DATA AND SPECIFICATIONS (SDS)

Revision: 2006 August

2006 Murano

SERVICE DATA AND SPECIFICATIONS (SDS)

PFP:00030

Road Wheel

NES000EY

Unit: mm (in)

Tire

NES000EZ

Unit: kPa (kg/cm

2

 , psi)

Tightening Torque

NES000F0

Kind of wheel

Aluminum

Steel (emergency use)

Deflection limit

Lateral runout limit

0.3 mm (0.012 in)

1.5 mm (0.059 in)

Radial runout limit

Allowable quantity of residual 
unbalance

Dynamic 
(On the ear part)

5 g (0.17 oz) (per side) or less

Static (On the ear part)

10 g (0.35 oz) or less

Wheel size

Offset

18 

×

 7-1/2 JJ

35 (1.38)

18 

×

 4T

25 (0.98)

Tire size

Air pressure 

Front wheel

Rear wheel

P235/65R18 104T

230 (2.3, 33)

230 (2.3, 33)

T165/90D18 107M

420 (4.2, 60)

420 (4.2, 60)

Wheel nut

108 N·m (11 kg-m, 80 ft-lb)

WW-1

WIPER, WASHER & HORN

K  ELECTRICAL

CONTENTS

C

D

E

F

G

H

I

J

L

M

SECTION 

A

B

WW

Revision: 2006 August

2006 Murano

WIPER, WASHER & HORN

PRECAUTION ............................................................ 3

Precautions for Supplemental Restraint System 
(SRS) “AIR BAG” and “SEAT BELT PRE-TEN-
SIONER” .................................................................. 3
Precautions for Procedures without Cowl Top Cover 

..... 3

FRONT WIPER AND WASHER SYSTEM .................. 4

Components Parts and Harness Connector Loca-
tion ........................................................................... 4
System Description  .................................................. 4

OUTLINE ............................................................... 4
LOW SPEED WIPER OPERATION  ...................... 5
HIGH SPEED WIPER OPERATION  ..................... 5
INTERMITTENT OPERATION  .............................. 5
AUTO STOP OPERATION .................................... 6
WASHER OPERATION ......................................... 6
MIST OPERATION ................................................ 7
FAIL-SAFE FUNCTION ......................................... 7
COMBINATION SWITCH READING FUNCTION 

..... 7

CAN Communication System Description ................ 9
CAN Communication Unit  ........................................ 9
Schematic .............................................................. 10
Wiring Diagram — WIPER —  .................................11
Terminals and Reference Values for BCM  ............. 14
Terminals and Reference Values for IPDM E/R  ..... 17
How to Proceed with Trouble Diagnosis  ................ 17
Preliminary Check  .................................................. 18

CHECK POWER SUPPLY AND GROUND CIR-
CUIT .................................................................... 18

CONSULT-II Functions (BCM)  ............................... 19

CONSULT-II BASIC OPERATION ....................... 19
WORK SUPPORT ............................................... 19
DATA MONITOR  ................................................. 19
ACTIVE TEST  ..................................................... 20

CONSULT-II Functions (IPDM E/R)  ....................... 21

CONSULT-II BASIC OPERATION ....................... 21
DATA MONITOR  ................................................. 21
ACTIVE TEST  ..................................................... 21

Front Wiper Does Not Operate  .............................. 22
Front Wiper Does Not Return to Stop Position ....... 24
Only Front Wiper Low Does Not Operate  .............. 25

Only Front Wiper Hi Does Not Operate  .................. 26
Only Front Wiper Intermittent Does Not Operate ... 28
Front Wiper Intermittent Operation Switch Position 
Cannot Be Adjusted ................................................ 28
Wiper Does Not Wipe When Front Washer Operates 

... 28

After Front Wiper Operate for 10 Seconds, They 
Stop for 20 Seconds, and after Repeating the Oper-
ations Five Times, They Become Inoperative  ........ 29
Front Wiper Does Not Stop ..................................... 30
Removal and Installation of Front Wiper Arms, 
Adjustment of Wiper Arms Stop Location  ............... 31

REMOVAL ........................................................... 31
INSTALLATION ................................................... 31
ADJUSTMENT .................................................... 31

Removal and Installation of Front Wiper Motor and 
Linkage ................................................................... 31

REMOVAL ........................................................... 31
INSTALLATION ................................................... 32

Disassembly and Assembly of Front Wiper Motor 
and Linkage  ............................................................ 32

DISASSEMBLY ................................................... 32
ASSEMBLY ......................................................... 32

Washer Nozzle Adjustment  .................................... 33
Washer Tube Layout  .............................................. 34
Removal and Installation of Front Washer Nozzle ... 34

REMOVAL ........................................................... 34
INSTALLATION ................................................... 34

Inspection for Washer Nozzle ................................. 34

CHECK VALVE INSPECTION  ............................. 34

Removal and Installation of Front Wiper and Washer 
Switch ..................................................................... 35

REMOVAL ........................................................... 35
INSTALLATION ................................................... 35

Removal and Installation of Washer Tank  .............. 35

REMOVAL ........................................................... 35
INSTALLATION ................................................... 35

Removal and Installation of Washer Pump ............. 36

REMOVAL ........................................................... 36
INSTALLATION ................................................... 36

WW-2

Revision: 2006 August

2006 Murano

REAR WIPER AND WASHER SYSTEM  .................. 37

Components Parts and Harness Connector Loca-
tion .......................................................................... 37
System Description ................................................. 37

OUT LINE  ............................................................ 37
REAR WIPER ON OPERATION .......................... 38
INTERMITTENT OPERATION  ............................ 38
AUTO STOP OPERATION  .................................. 38
WASHER OPERATION  ....................................... 38
BCM WIPER SWITCH READING FUNCTION .... 38

Wiring Diagram — WIP/ R —  ................................. 39
Terminals and Reference Values for BCM .............. 41
How to Proceed with Trouble Diagnosis  ................. 42
Preliminary Check  .................................................. 43

CHECK POWER SUPPLY AND GROUND CIR-
CUIT .................................................................... 43

CONSULT-II Functions (BCM) ................................ 44

CONSULT-II BASIC OPERATION  ....................... 44
DATA MONITOR .................................................. 44
ACTIVE TEST  ..................................................... 44

Rear Wiper Does Not Operate  ............................... 45
Rear Wiper Does Not Return to Stop Position ........ 46
Only Rear Wiper ON Does Not Operate ................. 47
Only Rear Wiper INT Does Not Operate  ................ 47
Wiper Does Not Wipe When Rear Washer Operates ... 47
Rear Wiper Do Not Stop  ......................................... 48
Removal and Installation of Rear Wiper Arm, Adjust-
ment of Wiper Arms Stop Location  ......................... 49

REMOVAL ........................................................... 49
INSTALLATION .................................................... 49
ADJUSTMENT .................................................... 49

Removal and Installation of Rear Wiper Motor  ....... 50

REMOVAL ............................................................50
INSTALLATION ....................................................50

Removal and Installation of Rear Wiper Blade  .......51

REMOVAL ............................................................51
INSTALLATION ....................................................51

Washer Nozzle Adjustment .....................................51
Washer Tube Layout  ...............................................52
Removal and Installation of Rear Washer Nozzle ...52
Check Valve Inspection ...........................................53
Removal and Installation of Rear Wiper and Washer 
Switch .....................................................................53
Removal and Installation of Washer Tank ...............53
Removal and Installation of Washer Pump  .............53

POWER SOCKET  .....................................................54

Wiring Diagram — P/SCKT —  ................................54
Removal and Installation of Instrument Power 
Socket .....................................................................55

REMOVAL ............................................................55
INSTALLATION ....................................................55

Removal and Installation of Luggage Room Power 
Socket .....................................................................55

REMOVAL ............................................................55
INSTALLATION ....................................................55

Removal and Installation of Console Power Socket ...55

REMOVAL ............................................................55
INSTALLATION ....................................................55

HORN ........................................................................56

Wiring Diagram — HORN —  ..................................56
Removal and Installation .........................................57

REMOVAL ............................................................57
INSTALLATION ....................................................57

PRECAUTION

WW-3

C

D

E

F

G

H

I

J

L

M

A

B

WW

Revision: 2006 August

2006 Murano

PRECAUTION

PFP:00011

Precautions for Supplemental Restraint System (SRS) “AIR BAG” and “SEAT 
BELT PRE-TENSIONER”

NKS001TO

The Supplemental Restraint System such as “AIR BAG” and “SEAT BELT PRE-TENSIONER”, used along
with a front seat belt, helps to reduce the risk or severity of injury to the driver and front passenger for certain
types of collision. This system includes seat belt switch inputs and dual stage front air bag modules. The SRS
system uses the seat belt switches to determine the front air bag deployment, and may only deploy one front
air bag, depending on the severity of a collision and whether the front occupants are belted or unbelted.
Information necessary to service the system safely is included in the SRS and SB section of this Service Man-
ual.

WARNING:

To avoid rendering the SRS inoperative, which could increase the risk of personal injury or death
in the event of a collision which would result in air bag inflation, all maintenance must be per-
formed by an authorized NISSAN/INFINITI dealer.

Improper maintenance, including incorrect removal and installation of the SRS, can lead to per-
sonal injury caused by unintentional activation of the system. For removal of Spiral Cable and Air
Bag Module, see the SRS section.

Do not use electrical test equipment on any circuit related to the SRS unless instructed to in this
Service Manual. SRS wiring harnesses can be identified by yellow and/or orange harnesses or
harness connectors.

Precautions for Procedures without Cowl Top Cover

NKS002TY

When performing the procedure after removing cowl top cover, cover
the lower end of windshield with urethane, etc.

PIIB3706J

WW-4

FRONT WIPER AND WASHER SYSTEM

Revision: 2006 August

2006 Murano

FRONT WIPER AND WASHER SYSTEM

PFP:28810

Components Parts and Harness Connector Location

NKS001TQ

System Description

NKS001TR

BCM (Body Control Module) controls front wiper low, high and intermittent operation.

IPDM E/R (Intelligent Power Distribution Module Engine Room) operates front wiper motor according to
CAN communication signals from BCM.

OUTLINE

Power is supplied at all times

to ignition relay located in IPDM E/R, from battery direct,

through 30 A fuse (No. 73 located in IPDM E/R)

to front wiper relay located in IPDM E/R,

through 15 A fuse (No. 78 located in IPDM E/R)

to CPU (central processing unit) located in IPDM E/R,

through 10 A fuse (No. 71, located in IPDM E/R)

to CPU located in IPDM E/R,

through 50 A fusible link (letter F, located in fuse and fusible link block)

to BCM terminal 55,

through 10 A fuse [No. 18 located in fuse block (J/B)]

to BCM terminal 42.

When the ignition switch ON or START position, power is supplied 

to ignition relay located in IPDM E/R,

PKIC7611E

FRONT WIPER AND WASHER SYSTEM

WW-5

C

D

E

F

G

H

I

J

L

M

A

B

WW

Revision: 2006 August

2006 Murano

through 10 A fuse [No. 1 located in fuse block (J/B)]

to BCM terminal 38,

through 10 A fuse (No. 84 located in IPDM E/R) 

through IPDM E/R terminal 44

to combination switch terminal 14.

Ground is supplied

to BCM terminal 52

through grounds M14 and M78,

to IPDM E/R terminals 38 and 60

through grounds E13, E26 and E28,

to combination switch terminal 12

through grounds M14 and M78.

LOW SPEED WIPER OPERATION

When the front wiper switch is in LO position, BCM detects the FR WIPER LOW (ON) by BCM combination
switch reading function. BCM sends front wiper request signal (LO) through CAN communication.
When receiving front wiper request signal (LO), IPDM E/R turns ON front wiper relay in IPDM E/R. IPDM E/R
supplies power

through IPDM E/R terminal 21, front wiper high relay and front wiper relay

to front wiper motor terminal 3.

Ground is supplied

to front wiper motor terminal 1

through grounds E13, E26 and E28.

With power and ground is supplied, the front wiper motor operates at low speed.

HIGH SPEED WIPER OPERATION

When the front wiper switch is in HI position, BCM detects the FR WIPER HI (HI) by BCM combination switch
reading function. BCM sends front wiper request signal (HI) through CAN communication.
When receiving front wiper request signal (HI), IPDM E/R turns ON front wiper relay and front wiper high relay
in IPDM E/R. IPDM E/R supplies power

through IPDM E/R terminal 31, front wiper high relay and front wiper relay

to front wiper motor terminal 2.

Ground is supplied

to front wiper motor terminal 1

through grounds E13, E26 and E28.

With power and ground is supplied, the front wiper motor operates at high speed.

INTERMITTENT OPERATION

Front wiper intermittent operation is determined from a combination of 3 switches (INT VOLUME 1, 2, and 3)
and vehicle speed signal*.
When the front wiper switch is in INT position, BCM detects the FR WIPER INT (ON) and ON/OFF status of
the INT VOLUME 1, 2, and 3 by BCM combination switch reading function. BCM judges the condition of wiper
intermittent dial position by ON/OFF status of INT VOLUME 1, 2, and 3 . 
BCM sends front wiper request signal (1LOW) at certain intervals through CAN communication. The interval is
calculated by wiper intermittent dial position and vehicle speed signal received from combination meter
through CAN communication.
When receiving front wiper request signal (1LOW), IPDM E/R turns ON front wiper relay in IPDM E/R, and
operates front wiper motor at low speed. Then IPDM E/R detects wiper arms reach to the stop position via
wiper auto stop signal from front wiper motor, IPDM E/R turns OFF front wiper relay, and sends front wiper
auto stop signal (ON) to BCM through CAN communication, and controls intermittent operation.

WW-6

FRONT WIPER AND WASHER SYSTEM

Revision: 2006 August

2006 Murano

Wiper Intermittent Dial Position Setting

Example: For wiper intermittent dial position 1
Using combination switch reading function, BCM detects ON/OFF status of INT VOLUME 1, 2, and 3.
When combination switch status is as listed below, BCM determines that it is wiper Intermittent dial position 1.

INT VOLUME 1: ON (Continuity exists between combination switch output 3 and input 1.)

INT VOLUME 2: ON (Continuity exists between combination switch output 5 and input 1.)

INT VOLUME 3: ON (Continuity exists between combination switch output 4 and input 2.)

BCM determines front wiper intermittent operation interval from wiper dial position 1 and vehicle speed*, and
sends wiper request signal (INT) to IPDM E/R.
*: Vehicle-speed-sensing intermittent wiper function reads vehicle speed signal when the function is ON. It is
set in OFF at the factory shipment. Vehicle-speed-sensing intermittent wiper function ON/OFF can be
changed by the CONSULT-II. Refer to 

WW-19, "WORK SUPPORT"

 .

AUTO STOP OPERATION

With wiper switch turned OFF, wiper motor will continue to operate until wiper arms reach windshield base.
When wiper arms are not located at base of windshield with wiper switch OFF, power is provided

from IPDM E/R terminal 21

to front wiper motor terminal 3, in order to continue wiper motor operation at low speed.

When wiper arms reach base of windshield, front wiper motor terminals 1 and 4 are connected, and ground is
supplied

to IPDM E/R terminal 32

through front wiper motor terminal 4 

through front wiper motor terminal 1 

through grounds E13, E26 and E28. 

Then the IPDM E/R sends front wiper auto stop signal (ON) to BCM with CAN communication line.
When the BCM receives front wiper auto stop signal (ON), BCM sends front wiper request signal (OFF) to
IPDM E/R with CAN communication line.
IPDM E/R stops wiper motor. Wiper motor will then stop wiper arms at the STOP position.

WASHER OPERATION

When the front washer switch is ON position, front and rear washer pump operates, and BCM detects the FR
WASHER (ON) by BCM combination switch reading function. Combination switch supplies power

through combination switch terminal 13

to front and rear washer pump terminal 1

Ground is supplied

to front and rear washer pump terminal 2

through combination switch terminal 11

to combination switch terminal 12

through grounds M14 and M78.

When BCM detects the FR WASHER (ON) for 0.4 seconds or longer, BCM sends front wiper request signal
(LO) through CAN communication. IPDM E/R operates front wiper motor at low speed.
When BCM detects the front washer switch is OFF, low speed wiper operation cycles approximately 2 times
and stops. 

Wiper intermittent dial 

position

Intermittent operation 

interval

Combination switch

INT VOLUME 1

INT VOLUME 2

INT VOLUME 3

1

Short

Long

ON

ON

ON

2

ON

ON

OFF

3

ON

OFF

OFF

4

OFF

OFF

OFF

5

OFF

OFF

ON

6

OFF

ON

ON

7

OFF

ON

OFF

 

 

 

 

 

 

 

Content      ..     207      208      209      210     ..