Nissan Murano Z50 (2006 year). Manual - part 119

CLIP AND FASTENER

EI-13

C

D

E

F

G

H

J

K

L

M

A

B

EI

Revision: 2006 August

2006 Murano

SIIA0317E

EI-14

FRONT BUMPER

Revision: 2006 August

2006 Murano

FRONT BUMPER

PFP:F2022

Removal and Installation

NIS001DZ

CAUTION:

Bumper fascia is made of resin. Do not apply strong force to it, and be careful to prevent contact with
oil.

PIIB7278E

FRONT BUMPER

EI-15

C

D

E

F

G

H

J

K

L

M

A

B

EI

Revision: 2006 August

2006 Murano

REMOVAL

1.

Remove bumper clips, front grille clips, and remove front grille.

2.

Remove bolts and clips on lower side of bumper.

3.

Remove screws and clips of both right/left fender protectors on front side. Refer to 

EI-21, "Removal and

Installation"

 .

4.

Remove screws of both right/left fender and remove bumper fascia assembly.

CAUTION:

When removing bumper fascia, 2 workers are required so as to prevent it from dropping.

5.

Remove front bumper energy absorber.

6.

Remove nuts of bumper reinforcement.

7.

Remove fog lamps located in bumper fascia. Refer to 

LT-113, "Removal and Installation"

 .

INSTALLATION

Install in the reverse order of removal.

NOTE:
After installation, adjust the clearance.

Removal and Installation of Bumper Center Molding

NIS001IJ

REMOVAL

1.

Remove front bumper fascia.

2.

Remove nuts of bumper fascia.

3.

Remove bumper center molding.

INSTALLATION

Install in the reverse order of removal.

1.

Bumper reinforcement

2.

Energy absorber

3.

Bumper air guide

4.

Bumper fascia assembly

5.

License plate bracket

6.

Bumper molding

7.

Bumper finisher

8.

Bumper guard

9.

Bumper deflector 

10. Bumper side bracket

11.

Bumper stay

12. Bumper clamp

13. Bumper center molding

Pawl

Portion

Clearance

Front bumper - Front grille

  A - A

                     0.5 - 3.5 mm (0.020 - 0.138 in)

Front bumper - Headlamp

  B - B

                     1.5 - 4.5 mm (0.059 - 0.177 in)

Front bumper - Front fender

  C - C

                     0.0 - 1.0 mm (0.000 - 0.040 in)

EI-16

REAR BUMPER

Revision: 2006 August

2006 Murano

REAR BUMPER

PFP:H5022

Removal and Installation

NIS001E0

CAUTION:

Bumper fascia is made of resin. Do not apply strong force to it, and be careful to prevent contact with
oil.

PIIB7279E

REAR BUMPER

EI-17

C

D

E

F

G

H

J

K

L

M

A

B

EI

Revision: 2006 August

2006 Murano

REMOVAL

1.

Remove rear combination lamp assembly. Refer to 

LT-181, "Removal and Installation"

 .

2.

Remove bumper fascia bolts from both right/left rear fender.

3.

Remove upper portion of bumper fascia clips, and remove clips of lower portion.

4.

Pull out center of bumper fascia, and pull out side of bumper fascia from clips.

5.

Remove bumper fascia assembly.

CAUTION:

When removing bumper fascia, 2 workers are required so as to prevent it from dropping.

6.

Remove rear bumper energy absorber.

7.

Remove bumper reinforcement nuts and remove bumper reinforce assembly.

INSTALLATION

Install in the reverse order of removal.

NOTE:
After installation, adjust the clearance.

REAR BUMPER CLOSING
Removal

1.

Remove clips of bumper closing.

2.

Remove bumper closing.

Installation

Install in the reverse order of removal.

1.

Bumper reinforcement

2.

Energy absorber

3.

Bumper fascia assembly

4.

Bumper side bracket

5.

Bumper stay

6.

Bumper over rider

7.

Clamp

8.

Bumper protector

9.

Bumper fascia bracket

Pawl

Portion

Clearance

Rear bumper - Rear fender

  A - A

                          0 - 1.0 mm (0.000 - 0.039 in)

Rear bumper - Back door

  B - B

                     6.0 - 10.0 mm (0.236 - 0.394 in)

PIIA3839E

EI-18

REAR BUMPER

Revision: 2006 August

2006 Murano

DRAFTER GUARD
Removal

1.

Remove nut and bolt of drafter guard.

2.

Remove drafter guard assembly.

Installation

Install in the reverse order of removal.

BUMPER PROTECTOR
Removal

1.

Remove rear bumper fascia.

2.

Remove nuts of bumper fascia bracket.

3.

Remove bumper protector.

Installation

Install in the reverse order of removal.

PIIA3840E

FRONT GRILLE

EI-19

C

D

E

F

G

H

J

K

L

M

A

B

EI

Revision: 2006 August

2006 Murano

FRONT GRILLE

PFP:62310

Removal and Installation

NIS001E1

CAUTION:

Apply protection tape around outer circumference of front grille (bumper fascia side).

REMOVAL

1.

Apply protection tape around outer circumference of front grille (bumper fascia side).

2.

Remove front grille-radiator cover clips and remove front grille-radiator cover.   

3.

Remove clips on upper side of front grille.

4.

Remove clips of air duct and remove air duct. Refer to 

EM-16, "AIR CLEANER AND AIR DUCT"

 .

5.

Pull out grille pawls, and remove front grille assembly.

INSTALLATION

Install in the reverse order of removal.

1.

Front grille

2.

Front grille-radiator cover (left)

3.

Front grille-radiator cover (right)

PIIA3831E

EI-20

COWL TOP

Revision: 2006 August

2006 Murano

COWL TOP

PFP:66100

Removal and Installation

NIS001E2

REMOVAL

1.

Remove both wiper arms (LH/RH). Refer to 

WW-31, "Removal and Installation of Front Wiper Arms,

Adjustment of Wiper Arms Stop Location"

 .

2.

Remove cowl top seal rubber.

3.

Remove clips of cowl top cover and remove cowl top cover (RH).

4.

Remove clips of cowl top cover and remove cowl top cover (LH).

5.

Remove washer nozzles and hose from cowl top cover.

INSTALLATION

Install in the reverse order of removal.

CAUTION:

After installing, perform adjustment of wiper arm. Refer to 

WW-31, "Removal and Installation of Front

Wiper Arms, Adjustment of Wiper Arms Stop Location"

 .

1.

Cowl top cover (RH)

2.

Cap (LH/RH)

3.

Cowl top seal rubber

4.

Cowl top cover (LH)

PIIA3832E

FENDER PROTECTOR

EI-21

C

D

E

F

G

H

J

K

L

M

A

B

EI

Revision: 2006 August

2006 Murano

FENDER PROTECTOR

PFP:63840

Removal and Installation

NIS001E3

REMOVAL

1.

Remove front bumper deflector. Refer to 

EI-14, "Removal and Installation"

 .

2.

Remove clips of splash guard.

3.

Remove splash guard.

4.

Remove screws of fender protector.

5.

Remove clips of fender protector.

6.

Remove fender protector (front/rear).

INSTALLATION

Install in the reverse order of removal.

1.

Fender protector (front)

2.

Splash guard

3.

Fender protector (rear)

PIIB4811E

EI-22

DOOR OUTSIDE MOLDING

Revision: 2006 August

2006 Murano

DOOR OUTSIDE MOLDING 

PFP:82820

Removal and Installation

NIS001E4

FRONT DOOR OUTSIDE MOLDING
Removal

1.

Open windows fully.

2.

Disengage front door outside molding pawl.

3.

Reaching from inner side of door use a clip tool to disengage
front door outside molding from the pawl.

NOTE:
Insert clip clamp tool into the door pawl, then disengage by
pressing in the direction of arrow (see figure on the right).

Installation

Install in the reverse order of removal.

CAUTION:

●

Be careful not to apply excessive force when removing because it is easy to deform parts.

●

After removal, visually inspect molding, and if it is deformed, replace it with new molding.

1.

Front door outside molding

2.

Rear door outside molding

PIIA3834E

PIIB5402E

DOOR OUTSIDE MOLDING

EI-23

C

D

E

F

G

H

J

K

L

M

A

B

EI

Revision: 2006 August

2006 Murano

REAR DOOR OUTSIDE MOLDING
Removal

1.

Open windows fully.

2.

Disengage rear door outside molding pawl.

3.

Reaching from inner side of door use a clip tool to disengage
rear door outside molding from the pawl.

NOTE:
Insert clip clamp tool into the door pawl, then disengage by pressing
in the direction of arrow (see figure on the right).

Installation

Install in the reverse order of removal.

CAUTION:

●

Be careful not to apply excessive force when removing because it is easy to deform parts.

●

After removal, visually inspect molding, and if it is deformed, replace it with new molding.

PIIB5401E

EI-24

DOOR OUTSIDE LOWER MOLDING

Revision: 2006 August

2006 Murano

DOOR OUTSIDE LOWER MOLDING

PFP:82877

Removal and Installation

NIS001E5

FRONT DOOR OUTSIDE LOWER MOLDING
Removal

Remove to slide molding to vehicle backward side, after disconnecting all clips.

Installation

Install in the reverse order of removal.

CAUTION:

●

Do not let air between contact surfaces when installing. 

●

To secure contact, do not wash vehicle within 24 hours after installation.

REAR DOOR OUTSIDE LOWER MOLDING
Removal

Remove to slide molding to vehicle backward side, after disconnecting all clips.

Installation

Install in the reverse order of removal.

CAUTION:

●

Do not let air between contact surfaces when installing. 

●

To secure contact, do not wash vehicle within 24 hours after installation.

FRONT FENDER LOWER MOLDING
Removal

Remove screw, and remove front fender lower molding. 

Installation

Install in the reverse order of removal.

PIIA3835E

1.

Front fender lower molding

2.

Front door lower molding

3.

Rear door lower molding

DOOR PARTING SEAL

EI-25

C

D

E

F

G

H

J

K

L

M

A

B

EI

Revision: 2006 August

2006 Murano

DOOR PARTING SEAL

PFP:80838

Removal and Installation

NIS001E6

REMOVAL

1.

Open front door and rear door fully.

2.

Remove seal clips and remove door parting seal.

3.

Remove rear door parting seal.

INSTALLATION

Install in the reverse order of removal.

CAUTION:

When installing door parting seal, make sure that blind clips are securely fitted in panel holes on body,
and then press them in.

1.

Door parting seal rubber

2.

Rear door parting seal rubber

PIIA3836E

EI-26

WINDSHIELD MOLDING

Revision: 2006 August

2006 Murano

WINDSHIELD MOLDING

PFP:72700

Removal and Installation

NIS001E7

WINDSHIELD MOLDING
Removal

Remove windshield molding. Refer to 

GW-11, "WINDSHIELD GLASS"

  .

Installation

Install windshield molding. Refer to 

GW-11, "WINDSHIELD GLASS"

  .

PIIA3784E

1.

Clip (C103)

2.

Fastener

3.

Molding

4.

Windshield glass

5.

Spacer

6.

Mirror base

7.

Bond

8.

Insulator

9.

Panel

10. Body side (outer)

11. Cowl top cover

SIDE WINDOW GLASS

EI-27

C

D

E

F

G

H

J

K

L

M

A

B

EI

Revision: 2006 August

2006 Murano

SIDE WINDOW GLASS

PFP:83300

Removal and Installation

NIS001E8

SIDE WINDOW MOLDING
Removal

Remove side window molding. Refer to 

GW-15, "Removal and Installation"

  . 

Installation

Install side window molding. Refer to 

GW-15, "Removal and Installation"

  .

PIIA3793E

1.

Side window glass molding (Upper)

2.

Side window glass

3.

Clip

4.

Side window glass molding (Lower)

5.

Bond

6.

Body side outer panel

EI-28

ROOF SIDE MOLDING

Revision: 2006 August

2006 Murano

ROOF SIDE MOLDING

PFP:73854

Removal and Installation

NIS001E9

REMOVAL

1.

Remove roof rail assembly. Refer to 

EI-29, "Removal and Installation"

 . 

2.

Disconnect molding clips from roof panel portion.

3.

Remove roof side molding from the front side.

INSTALLATION

Install in the reverse order of removal.

CAUTION:

To install roof side molding, check if all clips are matched over holes of panel on vehicle, then push it.

1.

Roof side molding

PIIA3848E