Nissan Murano Z50 (2005 year). Manual - part 193

PARKING BRAKE SHOE

PB-7

C

D

E

G

H

I

J

K

L

M

A

B

PB

Revision: 2005 August

2005 Murano

3.

After break-in operation, check lever stroke of the parking brake. Readjust if it is no longer at the specified
stroke.

●

To prevent the lining from getting too hot, allow a cool off period of approximately 5 minutes after every
break-in operation.

●

Do not perform excessive break-in operations, because it may cause uneven or early wear of the lining.

Drive forward

●

Vehicle speed approx. 40 km/h (25 MPH) set (forward)

●

Parking brake operating force approx. 147 N (15 kg, 33 lb) set

●

Distance approx. 100 m (328 ft)

PB-8

SERVICE DATA AND SPECIFICATIONS (SDS)

Revision: 2005 August

2005 Murano

SERVICE DATA AND SPECIFICATIONS (SDS)

PFP:00030

Parking Drum Brake 

AFS00187

Parking Brake Control

AFS00188

Type

DS19HC

Brake lining

Standard thickness (new)

3.2 mm (0.126 in)

Wear limit thickness

1.5 mm (0.059 in)

Drum (disc)

Standard inner diameter (new)

190 mm (7.48 in)

Wear limit of inner diameter

191 mm (7.52 in)

Control type

Foot pedal

Number of notches [under a force of 196 N (20 kg, 44 lb)]

3 to 4 notches

Number of notches
when warning lamp switch comes on

1 notches

PG-1

POWER SUPPLY, GROUND & CIRCUIT ELEMENTS

K  ELECTRICAL

CONTENTS

C

D

E

F

G

H

I

J

L

M

SECTION 

PG

A

B

PG

Revision: 2005 August

2005 Murano

POWER SUPPLY, GROUND & CIRCUIT ELEMENTS

POWER SUPPLY ROUTING CIRCUIT  ...................... 3

Schematic ................................................................ 3
Wiring Diagram - POWER -  ..................................... 4

BATTERY POWER SUPPLY - IGNITION SW. IN 
ANY POSITION ..................................................... 4
ACCESSORY POWER SUPPLY - IGNITION SW. 
IN “ACC” OR “ON”  ................................................ 9
IGNITION POWER SUPPLY - IGNITION SW. IN 
“ON” AND/OR “START” ....................................... 10

Fuse ....................................................................... 16
Fusible Link  ............................................................ 16
Circuit Breaker  ....................................................... 16

IPDM E/R (INTELLIGENT POWER DISTRIBUTION 
MODULE ENGINE ROOM)  ...................................... 17

System Description  ................................................ 17

SYSTEMS CONTROLLED BY IPDM E/R ........... 17
CAN COMMUNICATION LINE CONTROL  ......... 17
IPDM E/R STATUS CONTROL  ........................... 18

CAN Communication System Description .............. 18
CAN Communication Unit  ...................................... 18
Function of Detecting Ignition Relay Malfunction ... 18
CONSULT-II Function (IPDM E/R)  ......................... 19

CONSULT-II INSPECTION PROCEDURE  ......... 19
SELF-DIAG RESULTS  ........................................ 20
DATA MONITOR  ................................................. 21
ACTIVE TEST  ..................................................... 22

Auto Active Test  ..................................................... 23

DESCRIPTION .................................................... 23
OPERATION PROCEDURE  ............................... 23
INSPECTION IN AUTO ACTIVE TEST MODE ... 23

Schematic .............................................................. 25
IPDM E/R Terminal Arrangement  ........................... 26
IPDM E/R Power/Ground Circuit Inspection  .......... 27
Inspection With CONSULT-II (Self-Diagnosis)  ....... 28
Removal and Installation of IPDM E/R  ................... 29

REMOVAL ........................................................... 29
INSTALLATION ................................................... 29

GROUND ................................................................... 30

Ground Distribution ................................................. 30

MAIN HARNESS  ................................................. 30
ENGINE ROOM HARNESS  ................................ 33
ENGINE CONTROL HARNESS .......................... 35
BODY HARNESS  ................................................ 36
BODY NO. 2 HARNESS ..................................... 38

HARNESS ................................................................. 39

Harness Layout  ...................................................... 39

HOW TO READ HARNESS LAYOUT  ................. 39
OUTLINE ............................................................. 40
MAIN HARNESS  ................................................. 41
ENGINE ROOM HARNESS  ................................ 44
ENGINE CONTROL HARNESS .......................... 47
BODY HARNESS  ................................................ 49
BODY NO. 2 HARNESS ..................................... 51
ROOM LAMP HARNESS  .................................... 52
FRONT DOOR HARNESS  .................................. 53
REAR DOOR HARNESS  .................................... 54
BACK DOOR HARNESS  .................................... 55

Wiring Diagram Codes (Cell Codes)  ...................... 56

ELECTRICAL UNITS LOCATION  ............................ 59

Electrical Units Location  ......................................... 59

ENGINE COMPARTMENT  .................................. 59
PASSENGER COMPARTMENT  ......................... 60
LUGGAGE COMPARTMENT  .............................. 62

HARNESS CONNECTOR  ......................................... 63

Description .............................................................. 63

HARNESS CONNECTOR (TAB-LOCKING 
TYPE) .................................................................. 63
HARNESS CONNECTOR (SLIDE-LOCKING 
TYPE) .................................................................. 64

ELECTRICAL UNITS  ................................................ 65

Terminal Arrangement  ............................................ 65

SMJ (SUPER MULTIPLE JUNCTION)  ..................... 67

Terminal Arrangement  ............................................ 67

STANDARDIZED RELAY .......................................... 68

Description .............................................................. 68

NORMAL OPEN, NORMAL CLOSED AND 

PG-2

Revision: 2005 August

2005 Murano

MIXED TYPE RELAYS  ........................................ 68
TYPE OF STANDARDIZED RELAYS .................. 68

FUSE BLOCK - JUNCTION BOX (J/B)  .................... 70

Terminal Arrangement  ............................................ 70

FUSE, FUSIBLE LINK AND RELAY BOX  ................71

Terminal Arrangement .............................................71

POWER SUPPLY ROUTING CIRCUIT

PG-3

C

D

E

F

G

H

I

J

L

M

A

B

PG

Revision: 2005 August

2005 Murano

POWER SUPPLY ROUTING CIRCUIT

PFP:24110

Schematic

AKS007HE

TKWB0532E

PG-4

POWER SUPPLY ROUTING CIRCUIT

Revision: 2005 August

2005 Murano

Wiring Diagram - POWER -

AKS007HF

BATTERY POWER SUPPLY - IGNITION SW. IN ANY POSITION

TKWB0533E

POWER SUPPLY ROUTING CIRCUIT

PG-5

C

D

E

F

G

H

I

J

L

M

A

B

PG

Revision: 2005 August

2005 Murano

TKWB0534E

PG-6

POWER SUPPLY ROUTING CIRCUIT

Revision: 2005 August

2005 Murano

TKWA1744E

POWER SUPPLY ROUTING CIRCUIT

PG-7

C

D

E

F

G

H

I

J

L

M

A

B

PG

Revision: 2005 August

2005 Murano

TKWA1745E

PG-8

POWER SUPPLY ROUTING CIRCUIT

Revision: 2005 August

2005 Murano

TKWA1746E

POWER SUPPLY ROUTING CIRCUIT

PG-9

C

D

E

F

G

H

I

J

L

M

A

B

PG

Revision: 2005 August

2005 Murano

ACCESSORY POWER SUPPLY - IGNITION SW. IN “ACC” OR “ON”

TKWB0535E

PG-10

POWER SUPPLY ROUTING CIRCUIT

Revision: 2005 August

2005 Murano

IGNITION POWER SUPPLY - IGNITION SW. IN “ON” AND/OR “START”

TKWB0536E

POWER SUPPLY ROUTING CIRCUIT

PG-11

C

D

E

F

G

H

I

J

L

M

A

B

PG

Revision: 2005 August

2005 Murano

TKWB0537E

PG-12

POWER SUPPLY ROUTING CIRCUIT

Revision: 2005 August

2005 Murano

TKWB0538E

POWER SUPPLY ROUTING CIRCUIT

PG-13

C

D

E

F

G

H

I

J

L

M

A

B

PG

Revision: 2005 August

2005 Murano

TKWB0539E

PG-14

POWER SUPPLY ROUTING CIRCUIT

Revision: 2005 August

2005 Murano

TKWA1752E