Content .. 184 185 186 187 ..

Nissan Murano Z50 (2005 year). Manual - part 186

PARKING, LICENSE PLATE AND TAIL LAMPS

LT-163

Revision: 2005 August

2005 Murano

Preliminary Check

AKS00ALU

CHECK POWER SUPPLY AND GROUND CIRCUIT

CHECK FUSES

●

Check for blown fuses.

Refer to

LT-157, "Wiring Diagram — TAIL/L —"

OK or NG

>> GO TO 2.

>> If fuse is blown, be sure to eliminate cause of malfunction before installing new fuse. Refer to

PG-

3, "POWER SUPPLY ROUTING CIRCUIT"

CHECK POWER SUPPLY CIRCUIT

Turn ignition switch OFF.

Disconnect BCM connector.

Check voltage between BCM harness connector and ground.

OK or NG

>> GO TO 3.

>> Check harness for open or short between BCM and

fuse.

CHECK GROUND CIRCUIT

Check continuity between BCM harness connector and ground.

OK or NG

>> INSPECTION END

>> Check ground circuit harness.

Unit

Power source

Fuse and fusible link No.

BCM

Battery

Ignition switch ON or START position

Ignition switch ACC or ON position

IPDM E/R

Battery

Terminal

Ignition switch position

(+)

(-)

OFF

ACC

Connector

Terminal

(Wire color)

M34

11 (P/B)

Ground

Approx. 0V

Battery
voltage

38 (R)

Approx. 0V

Battery
voltage

M35

42 (GR)

Battery
voltage

55 (W/B)

Battery
voltage

PKIB5197E

Terminal

Continuity

Connector

Terminal (Wire color)

Ground

M35

52 (B)

Yes

PKIB5198E

LT-164

PARKING, LICENSE PLATE AND TAIL LAMPS

Revision: 2005 August

2005 Murano

CONSULT-II Functions (BCM)

AKS00ALV

Refer to

LT-17, "CONSULT-II Functions (BCM)"

in HEADLAMP - XENON TYPE.

Refer to

LT-50, "CONSULT-II Functions (BCM)"

in HEADLAMP - CONVENTIONAL TYPE.

CONSULT-II Functions (IPDM E/R)

AKS00CRH

Refer to

LT-20, "CONSULT-II Functions (IPDM E/R)"

in HEADLAMP - XENON TYPE.

Refer to

LT-53, "CONSULT-II Functions (IPDM E/R)"

in HEADLAMP - CONVENTIONAL TYPE.

Parking, License Plate and Tail Lamps Do Not Illuminate

AKS00ALW

CHECK COMBINATION SWITCH INPUT SIGNAL

With CONSULT-II

Select “BCM” on CONSULT-II. With “HEAD LAMP” data monitor,
make sure “LIGHT SW 1ST” turns ON-OFF linked with operation of
lighting switch.

Without CONSULT-II

Refer to

LT-145, "Combination Switch Inspection"

OK or NG

>> GO TO 2.

>> Check combination switch (lighting switch). Refer to

LT-

145, "Combination Switch Inspection"

ACTIVE TEST

With CONSULT-II

Select “IPDM E/R” on CONSULT-II, and select “ACTIVE TEST”
on “SELECT DIAG MODE” screen.

Select “TAIL LAMP” on “SELECT TEST ITEM” screen.

Touch “ON” screen.

Make sure parking, license plate, side marker and tail lamps
operate.

Without CONSULT-II

Start auto active test. Refer to

PG-23, "Auto Active Test"

Make sure parking, license plate, side marker and tail lamps operate.

OK or NG

>> GO TO 3.

>> GO TO 4.

When lighting switch is 1ST
position

: LIGHT SW 1 ST ON

PKIA7607E

Parking, license plate, side marker and tail lamp
should operate.

SKIA5957E

PARKING, LICENSE PLATE AND TAIL LAMPS

LT-165

Revision: 2005 August

2005 Murano

CHECK IPDM E/R

Select “IPDM E/R” on CONSULT-II, and select “DATA MONI-
TOR” on “SELECT DIAG MODE” screen.

Make sure “TAIL & CLR REQ” turns ON when lighting switch is
in 1ST position.

OK or NG

>> Replace IPDM E/R.

>> Replace BCM. Refer to

BCS-16, "Removal and Installa-

tion of BCM"

When lighting switch is 1ST
position

: TAIL & CLR REQ ON

SKIA5958E

LT-166

PARKING, LICENSE PLATE AND TAIL LAMPS

Revision: 2005 August

2005 Murano

CHECK INPUT SIGNAL

With CONSULT-II

Turn ignition switch OFF.

Disconnect front combination lamp RH and LH, license plate lamp RH and LH and rear combination lamp
RH and LH connectors.

Select “IPDM E/R” on CONSULT-II, and select “ACTIVE TEST” on “SELECT DIAG MODE” screen.

Select “TAIL LAMP” on “SELECT TEST ITEM” screen.

Touch “ON” screen.

When tail lamp is operating, check voltage between front combination lamp, license plate lamp, rear com-
bination lamp harness connector and ground.

Without CONSULT-II

Turn ignition switch OFF.

Disconnect front combination lamp RH and LH, license plate lamp RH and LH and rear combination lamp
RH and LH connectors.

Start auto active test. Refer to

PG-23, "Auto Active Test"

Check voltage between front combination lamp harness connector and ground.

Check voltage between license plate lamp harness connector and ground.

Check voltage between rear combination lamp harness connector and ground.

OK or NG

>> GO TO 6.

>> GO TO 5.

Terminal

Voltage

Front combination lamp (+)

(Parking)

(-)

Connector

Terminal (Wire color)

E30

7 (R/L)

Ground Battery

voltage

E17

7 (L/Y)

PKIA4917E

Terminal

Voltage

License plate lamp (+)

(-)

Connector

Terminal (Wire color)

D104

1 (R/L)

Ground

Battery voltage

D102

PKIB2156E

Terminal

Voltage

Rear combination lamp (+)

(Tail and side marker)

(-)

Connector

Terminal (Wire color)

B29

1 (R/L)

Ground

Battery voltage

B24

SKIA5962E

PARKING, LICENSE PLATE AND TAIL LAMPS

LT-167

Revision: 2005 August

2005 Murano

CHECK PARKING, LICENSE PLATE, SIDE MARKER AND TAIL LAMP CIRCUIT

Turn ignition switch OFF.

Disconnect IPDM E/R connector.

Check continuity between IPDM E/R harness connector and
front combination lamp harness connector.

Check continuity between IPDM E/R harness connector and
license plate lamp harness connector.

Check continuity between IPDM E/R harness connector and
rear combination lamp harness connector.

OK or NG

>> Replace IPDM E/R.

>> Repair harness or connector.

Terminal

Continuity

IPDM E/R

Front combination lamp

(Parking)

Connector

Terminal

(Wire color)

Connector

Terminal

(Wire color)

22 (L/Y)

E30

7 (R/L)

Yes

E17

7 (L/Y)

PKIA4919E

Terminal

Continuity

IPDM E/R

License plate lamp

Connector

Terminal

(Wire color)

Connector

Terminal

(Wire color)

22 (L/Y)

D104

1 (R/L)

Yes

D102

PKIB2157E

Terminal

Continuity

IPDM E/R

Rear combination lamp

(Tail and side marker)

Connector

Terminal

(Wire color)

Connector

Terminal

(Wire color)

22 (L/Y)

B29

1 (R/L)

Yes

B24

SKIA5966E

LT-168

PARKING, LICENSE PLATE AND TAIL LAMPS

Revision: 2005 August

2005 Murano

CHECK GROUND

Check continuity between front combination lamp harness con-
nector and ground.

Check continuity between license plate lamp harness connector
and ground.

Check continuity between rear combination lamp harness con-
nector and ground.

OK or NG

>> Check bulbs.

>> Repair harness or connector.

Parking, License Plate and Tail Lamps Do Not Turn OFF (After Approx. 10 Min-
utes)

AKS00ALX

CHECK IPDM E/R

Turn the ignition switch ON. Place the combination switch (lighting switch) in the ON position. Turn the
ignition switch OFF.

Make sure the parking, license plate, and tail lamps turn OFF after approximately 10 minutes.

OK or NG

>> INSPECTION END

>> Ignition relay malfunction. Refer to

PG-18, "Function of Detecting Ignition Relay Malfunction"

Terminal

Continuity

Front combination lamp

(Parking)

Ground

Connector

Terminal (Wire color)

E30

5 (B/W)

Yes

E17

PKIA6328E

Terminal

Continuity

License plate lamp

Ground

Connector

Terminal (Wire color)

D104

2 (B)

Yes

D102

PKIB2160E

Terminal

Continuity

Rear combination lamp

(Tail and side marker)

Ground

Connector

Terminal (Wire color)

B29

4 (B)

Yes

B24

PKIA6363E

PARKING, LICENSE PLATE AND TAIL LAMPS

LT-169

Revision: 2005 August

2005 Murano

Bulb Replacement

AKS00ALY

LICENSE PLATE LAMP

Remove back door inner finisher. Refer to

EI-40, "BACK DOOR

TRIM"

in “EI” section.

Disconnect the license plate lamp connector.

Turn bulb socket counterclockwise and unlock it.

Remove bulb from its socket.

Installation is the reverse order of removal.

PARKING LAMP (CLEARANCE LAMP)

For bulb replacement, refer to

LT-36, "Bulb Replacement"

in “HEADLAMP” (XENON TYPE).

For bulb replacement, refer to

LT-66, "Bulb Replacement"

in “HEADLAMP” (CONVENTIONAL TYPE).

TAIL LAMP

For bulb replacement, refer to

LT-170, "Bulb Replacement"

in “REAR COMBINATION LAMP”.

FRONT SIDE MARKER LAMP

For bulb replacement, refer to

LT-36, "Bulb Replacement"

in “HEADLAMP” (XENON TYPE).

For bulb replacement, refer to

LT-66, "Bulb Replacement"

in “HEADLAMP” (CONVENTIONAL TYPE).

REAR SIDE MARKER LAMP

For bulb replacement, refer to

LT-170, "Bulb Replacement"

in “REAR COMBINATION LAMP”.

Removal and Installation

AKS00ALZ

LICENSE PLATE LAMP

Remove back door inner finisher. Refer to

EI-40, "BACK DOOR

TRIM"

in “EI” section.

Remove rear wiper motor. Refer to

WW-51, "Removal and

Installation of Rear Wiper Motor"

Remove the license plate lamp mounting screws and remove it.

Installation is the reverse order of removal.

PARKING LAMP (CLEARANCE LAMP)

For parking lamp (clearance lamp) removal and installation procedures, refer to

LT-37, "Removal and Installa-

tion"

in “HEADLAMP” (XENON TYPE).

For parking lamp (clearance lamp) removal and installation procedures, refer to

LT-67, "Removal and Installa-

tion"

in “HEADLAMP” (CONVENTIONAL TYPE).

TAIL LAMP

For tail lamp removal and installation procedures, refer to

LT-170, "Removal and Installation"

in “REAR COM-

BINATION LAMP”.

FRONT SIDE MARKER LAMP

For headlamp removal and installation procedures, refer to

LT-37, "Removal and Installation"

in “HEALAMP”

(XENON TYPE).
For headlamp removal and installation procedures, refer to

LT-67, "Removal and Installation"

in “HEALAMP”

(CONVENTIONAL TYPE).

REAR SIDE MARKER LAMP

For rear side marker lamp removal and installation procedures, refer to

LT-170, "Removal and Installation"

“REAR COMBINATION LAMP”.

License plate lamp

: 12V - 5W

PKIA2531E

PKIB2161E

LT-170

REAR COMBINATION LAMP

Revision: 2005 August

2005 Murano

REAR COMBINATION LAMP

PFP:26554

Bulb Replacement

AKS005M1

STOP & TAIL LAMP BULB, REAR SIDE MARKER LAMP BULB, REAR TURN SIGNAL LAMP
BULB

Remove rear combination lamp. Refer to

LT-170, "Removal and

Installation"

Turn bulb socket counterclockwise and unlock it.

Remove bulb.

Installation is the reverse order of removal.

Removal and Installation

AKS005M2

REMOVAL

Remove rear combination lamp finisher.

Remove rear combination lamp mounting bolts.

Pull the rear combination lamp toward side of the vehicle and
remove from the vehicle.

Disconnect rear combination lamp connector.

INSTALLATION

Installation is the reverse order of removal.

Stop/tail lamp

: 12V - 21/5W

Rear side marker lamp

: 12V - 5W

Rear turn signal lamp

: 12V - 21W

PKIA2532E

PKIA2533E

Rear combination lamp mounting bolt

: 5.5 N·m (0.56 kg-m, 49 in-lb)

VANITY MIRROR LAMP

LT-171

Revision: 2005 August

2005 Murano

VANITY MIRROR LAMP

PFP:96400

Bulb Replacement

AKS005M3

Wiring diagram. Refer to

LT-182, "Wiring Diagram — ROOM/L —"

Insert a thin screwdriver in the notch and remove lens.

Remove bulb.

Installation is the reverse order of removal.

Vanity mirror lamp

: 12V - 2W

PKIB2178E

LT-172

MAP LAMP

Revision: 2005 August

2005 Murano

MAP LAMP

PFP:26430

Bulb Replacement

AKS005M4

Wiring diagram. Refer to

LT-182, "Wiring Diagram — ROOM/L —"

Disconnect the battery negative cable.

Remove the lens using clip driver or suitable tool.

Remove the bulb.

Installation is the reverse order of removal.

Removal and Installation

AKS005M5

REMOVAL

Pull wider part of thin plate of the map lamp to disengage the
metal clip.

Pull map lamp in direction shown by the arrow in the figure.

Disconnect map lamp connector and remove the map lamp.

INSTALLATION

Installation is the reverse order of removal.

Map lamp

: 12V - 8 W

PKIA2534E

PKIA2520E

PERSONAL LAMP

LT-173

Revision: 2005 August

2005 Murano

PERSONAL LAMP

PFP:26415

Bulb Replacement, Removal and Installation

AKS004LW

Wiring diagram. Refer to

LT-182, "Wiring Diagram — ROOM/L —"

Insert a clip driver or suitable tool and disengage the metal clip
fittings of the personal lamp.

Disconnect personal lamp connector and remove the personal
lamp.

Remove the housing mounting screws, and separate it.

Remove bulb from the base.

Installation is the reverse order of removal.

PKIA2540E

Personal lamp

: 12V - 8W

PKIA2536E

LT-174

LUGGAGE ROOM LAMP

Revision: 2005 August

2005 Murano

LUGGAGE ROOM LAMP

PFP:26410

Bulb Replacement, Removal and Installation

AKS005M6

Wiring diagram. Refer to

LT-182, "Wiring Diagram — ROOM/L —"

Insert a screwdriver as shown in the figure and pull out the lug-
gage room lamp.

Disconnect the luggage room lamp connector.

Remove the bulb.

Installation is the reverse order of removal.

PKIA1884E

PKIA2541E

Luggage room lamp

: 12V - 8W

PKIA2537E

INTERIOR ROOM LAMP

LT-175

Revision: 2005 August

2005 Murano

INTERIOR ROOM LAMP

PFP:26410

Component Parts and Harness Connector Location

AKS00AME

System Description

AKS005R0

When the room lamp and personal lamp switch is in DOOR position, room lamp and personal lamp ON/OFF is
controlled by timer according to signals from switches including key switch, front door switch driver side,
unlock signal from key fob, door lock and unlock switch, key cylinder lock and unlock switch, ignition switch.
When the room lamp and personal lamp turns ON, there is a gradual brightening over 1 second. When room
lamp and personal lamp turns OFF, there is a gradual dimming over 1 second.
The room lamp and personal lamp timer is controlled by the BCM (body control module).
Room lamp and personal lamp timer control settings can be changed with CONSULT-II.
Ignition key hole illumination turns ON at time when driver door is opened (door switch ON) or removed key
fob from key cylinder. Illumination turns OFF when driver door is closed (door switch OFF).
Step lamp turns ON at time when driver door or passenger door is opened (door switch ON). Lamp turns OFF
when driver, passenger doors are closed (all door switches OFF).

PKIB2179E

LT-176

INTERIOR ROOM LAMP

Revision: 2005 August

2005 Murano

POWER SUPPLY AND GROUND

Power is supplied at all times (without Intelligent Key system)

●

through 10A fuse [No. 21, located in fuse block (J/B)]

●

to key switch terminal 3,

●

through 50A fusible link (letter F, located in fuse and fusible link block)

●

to BCM terminal 55.

Power is supplied at all times (with Intelligent Key system)

●

through 10A fuse [No.22, located in fuse block (J/B)]

●

to key switch and ignition knob switch terminals 1 and 3,

●

through 10A fuse [No. 18, located in fuse block (J/B)]

●

to BCM terminal 42,

●

through 50A fusible link (letter F, located in fuse and fusible link block)

●

to BCM terminal 55.

When the key is inserted to ignition key cylinder, power is interrupted (without Intelligent Key system)

●

through key switch terminal 4

●

to BCM terminal 37.

When inserted key plate to key switch and ignition knob switch, power is supplied (with Intelligent Key system)

●

through key switch and ignition knob switch terminal 4

●

to BCM terminal 37.

When pushed key switch and ignition knob switch, power is supplied (with Intelligent Key system)

●

through key switch and ignition knob switch terminal 2

●

to intelligent key unit terminal 27.

With the ignition switch in the ON or START position, power is supplied

●

through 10A fuse [No. 1, located in fuse block (J/B)]

●

to BCM terminal 38.

Ground is supplied

●

to BCM terminal 52

●

through grounds E13, E26 and E28.

When the driver side door is opened, ground is supplied

●

to BCM terminal 62

●

through front door lock assembly (driver side) (door switch) terminal 4

●

through front door lock assembly (driver side) (door switch) terminal 5

●

through grounds M14 and M78.

When the passenger side door is opened, ground is supplied

●

to BCM terminal 12

●

through front door lock assembly (passenger side) (door switch) terminal 4

●

through front door lock assembly (passenger side) (door switch) terminal 5

●

through grounds M14 and M78.

When the rear door LH is opened, ground is supplied

●

to BCM terminal 63

●

through rear door lock assembly LH (door switch) terminal 4

●

through rear door lock assembly LH (door switch) terminal 5

●

through grounds B7 and B20.

When the rear door RH is opened, ground is supplied

●

to BCM terminal 13

●

through rear door lock assembly RH (door switch) terminal 4

●

through rear door lock assembly RH (door switch) terminal 5

●

through grounds B105 and B116.

When the driver side door is unlocked by the door lock and unlock switch, BCM receives a ground signal

INTERIOR ROOM LAMP

LT-177

Revision: 2005 August

2005 Murano

●

through grounds M14 and M78

●

to power window main switch (door lock and unlock switch) terminal 17 or front power window switch
(passenger side) (door lock and unlock switch) terminal 11

●

from power window main switch (door lock and unlock switch) terminal 14 or front power window switch
(passenger side) (door lock and unlock switch) terminal 16

●

to BCM terminal 22.

When the front driver side door is unlocked by the driver side door lock assembly (door key cylinder switch),
BCM receives a ground signal

●

through grounds M14 and M78

●

to front door lock assembly (driver side) (door key cylinder switch) terminal 5 (without Intelligent Key sys-
tem)

●

to door key cylinder switch terminal 2 (with Intelligent Key system)

●

from front door lock assembly (driver side) (door key cylinder switch) terminal 6 (without Intelligent Key
system)

●

from door key cylinder switch terminal 3 (with Intelligent Key system)

●

to power window main switch (door lock and unlock switch) terminal 6

●

from power window main switch (door lock and unlock switch) terminal 14

●

to BCM terminal 22.

When a signal, or combination of signals is received by BCM, ground is supplied

●

to room lamp terminal 1 and

●

to personal lamp LH and RH terminal 3

●

through BCM terminal 48.

With power and supplied, the interior lamp illuminates.

SWITCH OPERATION

When driver door switch is ON (door is opened), ground is supplied

●

to ignition key hole illumination terminal 2

●

through BCM terminal 1.

And power is supplied

●

from BCM terminal 41

●

to ignition key hole illumination terminal 1.

When any door switch is ON (door is opened), ground is supplied

●

through BCM terminal 47

●

to step lamp (driver side and passenger side) terminal 2.

And power is supplied

●

from BCM terminal 41

●

to step lamp (driver side and passenger side) terminal 1.

When map lamp switch is ON, ground is supplied

●

to map lamp terminal 2

●

through grounds M14 and M78.

And power is supplied

●

from BCM terminal 41

●

to map lamp terminal 1.

When vanity mirror lamp (driver side and passenger side) is ON, ground is supplied

●

to vanity mirror lamp (driver side and passenger side) terminal 2

●

through grounds M14 and M78.

And power is supplied

●

from BCM terminal 41

●

to vanity mirror lamp (driver side and passenger side) terminal 1.

When personal lamp LH and RH switch is ON, ground is supplied

LT-178

INTERIOR ROOM LAMP

Revision: 2005 August

2005 Murano

●

to personal lamp LH and RH terminal 2

●

through grounds M14 and M78.

And power is supplied

●

from BCM terminal 41

●

to personal lamp LH and RH terminal 1.

When room lamp switch is ON, ground is supplied

●

to room lamp terminal 3

●

through grounds M14 and M78.

And power is supplied

●

from BCM terminal 41

●

to room lamp terminal 2.

When luggage room lamp RH and LH is ON, and then back door switch is ON, ground is supplied

●

to luggage room lamp RH and LH terminal 2

●

through back door switch terminal 3

●

through back door switch terminal 4

●

through grounds B7 and B20.

And power is supplied

●

from BCM terminal 41

●

to luggage room lamp RH and LH terminal 1.

ROOM LAMP TIMER OPERATION
Without Intelligent Key System

When room lamp and personal lamp switch is in DOOR position, and when all conditions below are met, BCM
performs timer control (maximum 30 seconds) for room lamp and personal lamp ON/OFF.
In addition, when spot turns ON or OFF there is gradual brightening or dimming over 1 second.
Power is supplied

●

through 10A fuse [No. 21, located in the fuse block (J/B)]

●

to key switch terminal 3.

Key is removed from ignition key cylinder (key switch OFF), power will not be supplied to BCM terminal 37.
Ground is supplied

●

from BCM terminal 22

●

to power window main switch (door lock and unlock switch) terminal 14.

At this time, BCM detects that driver door is unlocked. It determines that room lamp and personal lamp timer
operation conditions are met, and turns the room lamp and personal lamp ON for 30 seconds.
Key is in ignition key cylinder (key switch ON),
Power is supplied

●

through key switch terminal 4

●

to BCM terminal 37.

When key is removed from key switch (key switch OFF), power supply to BCM terminal 37 is terminated. BCM
detects that key has been removed, determines that room lamp and personal lamp timer conditions are met,
and turns the room lamp and personal lamp ON for 30 seconds.
When driver door opens

→

closes, and the key is not inserted in the key switch and key lock solenoid (key

switch OFF), BCM terminal 62 changes between 0V (door open)

→

12V (door closed). The BCM determines

that conditions for room lamp and personal lamp operation are met and turns the interior lamp ON for 30 sec-
onds.
Timer control is canceled under the following conditions.

●

Driver door is locked [when locked key fob or power window main switch (door lock and unlock switch),
door key cylinder switch]

●

Driver door is opened (driver door switch turns ON)

●

Ignition switch ON.

Content .. 184 185 186 187 ..