The Supplemental Restraint System such as “AIR BAG” and “SEAT BELT PRE-TENSIONER”, used along
with a front seat belt, helps to reduce the risk or severity of injury to the driver and front passenger for certain
types of collision. This system includes seat belt switch inputs and dual stage front air bag modules. The SRS
system uses the seat belt switches to determine the front air bag deployment, and may only deploy one front
air bag, depending on the severity of a collision and whether the front occupants are belted or unbelted.
Information necessary to service the system safely is included in the SRS and SB section of this Service Man-
ual.

WARNING:

●

To avoid rendering the SRS inoperative, which could increase the risk of personal injury or death
in the event of a collision which would result in air bag inflation, all maintenance must be per-
formed by an authorized NISSAN/INFINITI dealer.

●

Improper maintenance, including incorrect removal and installation of the SRS, can lead to per-
sonal injury caused by unintentional activation of the system. For removal of Spiral Cable and Air
Bag Module, see the SRS section.

●

Do not use electrical test equipment on any circuit related to the SRS unless instructed to in this
Service Manual. SRS wiring harnesses can be identified by yellow and/or orange harnesses or
harness connectors.

Precautions Necessary for Steering Wheel Rotation After Battery Disconnect

ACS009AK

NOTE:

●

This Procedure is applied only to models with Intelligent Key system and NVIS/IVIS (NISSAN/INFINITI
VEHICLE IMMOBILIZER SYSTEM - NATS).

●

Remove and install all control units after disconnecting both battery cables with the ignition knob in the

″

LOCK

″

position.

●

Always use CONSULT-II to perform self-diagnosis as a part of each function inspection after finishing
work. If DTC is detected, perform trouble diagnosis according to self-diagnostic results.

For models equipped with the Intelligent Key system and NVIS/IVIS, an electrically controlled steering lock
mechanism is adopted on the key cylinder.
For this reason, if the battery is disconnected or if the battery is discharged, the steering wheel will lock and
steering wheel rotation will become impossible.
If steering wheel rotation is required when battery power is interrupted, follow the procedure below before
starting the repair operation.

OPERATION PROCEDURE

Connect both battery cables.

NOTE:
Supply power using jumper cables if battery is discharged.

Use the Intelligent Key or mechanical key to turn the ignition switch to the

″

ACC

″

position. At this time, the

steering lock will be released.

Disconnect both battery cables. The steering lock will remain released and the steering wheel can be
rotated.

Perform the necessary repair operation.

When the repair work is completed, return the ignition switch to the

″

LOCK

″

position before connecting

the battery cables. (At this time, the steering lock mechanism will engage.)

Perform a self-diagnosis check of all control units using CONSULT-II.

PRECAUTIONS

CVT-9

CVT

Revision: 2005 August

2005 Murano

Precautions for TCM and CVT Assembly Replacement

ACS001SA

CAUTION:

●

Check if new data (Unit ID) are entered correctly after replacing CVT assembly and erasing data in
TCM. (Connect CONSULT-II, and then turn ignition switch OFF.)

●

When replacing CVT assembly or TCM, refer to the pattern table below and erase the EEPROM in the
TCM if necessary.

EEPROM ERASING PATTERNS

METHOD FOR ERASING THE EEPROM IN THE TCM

Connect CONSULT-II to data link connector. Refer to

CVT-64, "CONSULT-II SETTING PROCEDURE"

Turn ignition switch ON. Confirm that CONSULT-II is turned ON.

Move selector lever to “R” position.

Touch “START (NISSAN BASED VHCL)” on CONSULT-II.

Select “SELF-DIAG RESULTS” mode for “TRANSMISSION” with CONSULT-II.

Press the brake pedal and turn the brake switch ON.

Press the accelerator pedal (0.5/8 - 4/8 throttle) not to exceed the half, and hold it in the half or less open
position. (This will set the closed throttle position signal to OFF and the wide open throttle position signal
to “OFF”.)

Touch “ERASE” on CONSULT-II, and then touch “YES”.

Wait 3 seconds and then release the accelerator pedal.

10. Turn ignition switch OFF.

METHOD FOR WRITING DATA FROM THE ROM ASSEMBLY IN THE TRANSAXLE

In the following procedure, the TCM reads data from the ROM assembly and writes it to the EEPROM in the
TCM.

Erase the EEPROM in the TCM.

Move selector lever to “P” position.

Turn ignition switch ON.

CHECK METHOD

●

Standard: About 2 seconds after the ignition switch ON, the CVT indicator lamp lights up for 2 seconds.

●

Non-standard: Even after the ignition switch ON, the CVT indicator lamp does not light up after 2 seconds
or illuminates immediately.

CAUTION:

Perform in the “P” or “N” position.

Action for Non-standard

●

Replace the CVT assembly.

●

Replace the TCM.

CVT assembly

TCM

Erasing EEPROM in TCM

Remarks

Replaced

Not required

Not required because the EEPROM in the TCM is in
the default state. (CVT assembly must be replaced
first.)

Not replaced

Replaced

Not required

Not required because the EEPROM in the TCM is in
the default state.

Replaced

Not replaced

Required

Required because data has been written in the
EEPROM in the TCM and because the TCM cannot
write data from the ROM assembly in the transmis-
sion.

CVT-10

PRECAUTIONS

Revision: 2005 August

2005 Murano

Removal and Installation Procedure for CVT Unit Connector

ACS003L1

REMOVAL

●

Rotate bayonet ring counterclockwise, pull out CVT unit harness
connector upward and remove it.

INSTALLATION

Align

∆

marking on CVT unit harness connector terminal body

with

❏

marking on bayonet ring, insert CVT unit harness con-

nector, and then rotate bayonet ring clockwise.

Rotate bayonet ring clockwise until

∆

marking on CVT unit har-

ness connector terminal body is aligned with the slit on bayonet
ring as shown in the figure (correctly fitting condition), install
CVT unit harness connector to CVT unit harness connector ter-
minal body.

CAUTION:

●

Securely align

∆

marking on CVT unit harness connector

terminal body with bayonet ring slit. Then, be careful not
to make a half fit condition as shown in the figure.

●

Do not mistake the slit of bayonet ring for other dent por-
tion.

SCIA2096E

SCIA2097E

SCIA2098E

SCIA2099E

PRECAUTIONS

CVT-11

CVT

Revision: 2005 August

2005 Murano

Precautions

ACS001SB

NOTE:
If any malfunction occurs in the RE0F09A model transaxle, replace the entire transaxle assembly.

●

Before connecting or disconnecting the TCM harness con-
nector, turn ignition switch OFF and disconnect negative
battery cable. Because battery voltage is applied to TCM
even if ignition switch is turned OFF.

●

When connecting or disconnecting pin connectors into or
from TCM, take care not to damage pin terminals (bend or
break).
When connecting pin connectors make sure that there are
not any bends or breaks on TCM pin terminal.

●

Before replacing TCM, perform TCM input/output signal
inspection and make sure whether TCM functions properly
or not.

CVT-58, "TCM INSPECTION TABLE"

●

After performing each TROUBLE DIAGNOSIS, perform
“DTC Confirmation Procedure”.
If the repair is completed the DTC should not be displayed
in the “DTC Confirmation Procedure”.

●

Always use the specified brand of CVT fluid. Refer to

MA-10,

"Fluids and Lubricants"

●

Use lint-free paper, not cloth rags, during work.

●

After replacing the CVT fluid, dispose of the waste oil using the
methods prescribed by law, ordinance, etc.

SEF289H

SEF291H

MEF040DA

SEF217U

CVT-12

PRECAUTIONS

Revision: 2005 August

2005 Murano

Service Notice or Precautions

ACS001SC

CVT FLUID COOLER SERVICE

If CVT fluid contains friction material (clutches, bands, etc.), or if an CVT is replaced, inspect and clean the
CVT fluid cooler mounted in the radiator or replace the radiator. Flush cooler lines using cleaning solvent and
compressed air after repair. For CVT fluid cooler cleaning procedure, refer to

CVT-17, "CVT Fluid Cooler

Cleaning"

. For radiator replacement, refer to

CO-13, "RADIATOR"

OBD-II SELF-DIAGNOSIS

●

CVT self-diagnosis is performed by the TCM in combination with the ECM. The results can be read
through the blinking pattern of the malfunction indicator lamp (MIL). Refer to the table on

CVT-67, "Display

Items List"

for the indicator used to display each self-diagnostic result.

●

The self-diagnostic results indicated by the MIL are automatically stored in both the ECM and TCM mem-
ories.
Always perform the procedure on

CVT-30, "HOW TO ERASE DTC"

to complete the repair and

avoid unnecessary blinking of the MIL.

For details of OBD-II, refer to

EC-46, "ON BOARD DIAGNOSTIC (OBD) SYSTEM"

●

Certain systems and components, especially those related to OBD, may use the new style slide-
locking type harness connector. For description and how to disconnect, refer to

PG-63, "HAR-

NESS CONNECTOR"

PREPARATION

CVT-13

CVT

Revision: 2005 August

2005 Murano

PREPARATION

PFP:00002

Special Service Tools

ACS001SE

The actual shapes of Kent-Moore tools may differ from those of special service tools illustrated here.

Tool number
(Kent-Moore No.)
Tool name

Description

—

(OTC3492)
Oil pressure gauge set

Measuring line pressure

—

(J-34339-A)
Drift
a: 85.69 mm (3.37 in) dia.
b: 50.4 mm (1.98 in) dia

Installing differential side oil seal

●

With AWD models

●

Converter housing side (right)

—

(J-47244)
Drift
a: 65.83 mm (2.59 in) dia.
b: 53.85 mm (2.12 in) dia.

Installing differential side oil seal

●

Transaxle case side (left)

ST33400001
(J-47005)
Drift
a: 69.85 mm (2.75 in) dia.
b: 49.53 mm (1.95 in) dia.

Installing differential side oil seal

●

With 2WD models

●

Converter housing side (right)

SCIA7531E

NT084

SCIA5777E

CVT-14

PREPARATION

Revision: 2005 August

2005 Murano

Commercial Service Tools

ACS001SF

(Tool number)
Tool name

Description

(31197CA000)
Drive plate location guide
a: 14 mm (0.55 in) dia.

Installing transaxle assembly

(31093CA000)
Slinger

Removing and installing transaxle assembly

(31092CA000)
Slinger

Removing and installing transaxle assembly

Power tool

Loosening nuts and bolts

SCIA2013E

SCIA2014E

SCIA2015E

PBIC0190E

CVT FLUID

CVT-15

CVT

Revision: 2005 August

2005 Murano

CVT FLUID

PFP:KLE50

Checking CVT Fluid

ACS002KW

FLUID LEVEL CHECK

Fluid level should be checked with the fluid warmed up to 50 to 80

C (122 to 176

F). The fluid level check pro-

cedure is as follows:

Check for fluid leakage.

With the engine warmed up, drive the vehicle in an urban area.
When ambient temperature is 20

C (68

F), it takes about 10

minutes for the CVT fluid to warm up to 50 - 80

C (122 - 176

F).

Park the vehicle on a level surface.

Apply parking brake firmly.

With engine at idle, while depressing brake pedal, move shift
selector throughout the entire shift range.

Pull out the CVT fluid level gauge from the CVT fluid charging
pipe after pressing the tab on the CVT fluid level gauge to
release the lock.

Wipe fluid off the CVT fluid level gauge. Insert the CVT fluid
level gauge rotating 180

from the originally installed position,

then securely push the CVT fluid level gauge until it meets the
top end of the CVT fluid charging pipe.

CAUTION:

When wiping away the CVT fluid level gauge, always use
lint-free paper, not a cloth rag.

Place the selector lever in “P” or “N” and make sure the fluid
level is within the specified range.

CAUTION:

●

When reinstalling CVT fluid level gauge, insert it into the
CVT fluid charging pipe and rotate it to the original instal-
lation position until it is securely locked.

SMA146B

SCIA1933E

SCIA1931E

SCIA1932E

CVT-16

CVT FLUID

Revision: 2005 August

2005 Murano

Check CVT fluid condition.

●

If CVT fluid is very dark or smells burned, check operation of
CVT. Flush cooling system after repair of CVT.

●

If CVT fluid contains frictional material (clutches, bands, etc.),
replace radiator and flush cooler line using cleaning solvent
and compressed air after repair of CVT. Refer to

CO-13,

"RADIATOR"

and

CVT-17, "CVT Fluid Cooler Cleaning"

Changing CVT Fluid

ACS002KX

Warm up CVT fluid by driving the vehicle for 10 minutes.

●

: Vehicle front

●

Radiator (2)

●

CVT fluid cooler hose [inlet side (3)]

●

Transaxle assembly (4)

Drain CVT fluid from CVT fluid cooler hose [outlet side (1)] and
refill with new CVT fluid at CVT fluid charging pipe with the
engine running at idle speed.

Refill until new CVT fluid comes out from CVT fluid cooler hose
(outlet side).
About 30 to 50% extra fluid will be required for this procedure.

CAUTION:

●

Use only Genuine Nissan CVT fluid NS-2. Do not mix with other fluid.

●

Using CVT fluid other than Genuine Nissan CVT fluid NS-2 will deteriorate in driveability and
CVT durability, and may damage the CVT, which is not covered by the warranty.

●

When filling CVT fluid, take care not to scatter heat generating parts such as exhaust.

●

Delete CVT fluid deterioration date with CONSULT-II after changing CVT fluid. Refer to

CVT-66,

"Check CVT Fluid Deterioration Date"

Check fluid level and condition.

ATA0022D

CVT fluid:

Genuine Nissan CVT fluid NS-2

Fluid capacity:

Approx. 10.2 (10-6/8 US qt, 9 lmp qt)

SCIA6088E

CVT FLUID

CVT-17

CVT

Revision: 2005 August

2005 Murano

CVT Fluid Cooler Cleaning

ACS004MD

Whenever an automatic transaxle is repaired, overhauled, or replaced, the CVT fluid cooler mounted in the
radiator must be inspected and cleaned.
Metal debris and friction material, if present, can be trapped or become deposit in the CVT fluid cooler. This
debris can contaminate the newly serviced CVT or, in severe cases, can block or restrict the flow of CVT fluid.
In either case, malfunction of the newly serviced CVT may occur.
Debris, if present, may deposit as CVT fluid enters the cooler inlet. It will be necessary to back flush the cooler
through the cooler outlet in order to flush out any built up debris.

CVT FLUID COOLER CLEANING PROCEDURE

Position an oil pan under the transaxle's inlet and outlet cooler hoses.

Identify the inlet and outlet fluid cooler hoses.

Disconnect the fluid cooler inlet and outlet rubber hoses from the
steel cooler tubes or bypass valve.

NOTE:
Replace the cooler hoses if rubber material from the hose
remains on the tube fitting.

Allow any CVT fluid that remains in the cooler hoses to drain into
the oil pan.

Insert the extension adapter hose of a can of Transmission
Cooler Cleaner (Nissan P/N 999MP-AM006) into the cooler out-
let hose.

CAUTION:

●

Wear safety glasses and rubber gloves when spraying
the Transmission Cooler Cleaner.

●

Spray cooler cleaner only with adequate ventilation.

●

Avoid contact with eyes and skin.

●

Do not breath vapors or spray mist.

Hold the hose and can as high as possible and spray Transmis-
sion Cooler Cleaner in a continuous stream into the cooler outlet
hose until fluid flows out of the cooler inlet hose for 5 seconds.

Insert the tip of an air gun into the end of the cooler outlet hose.

Wrap a shop rag around the air gun tip and of the cooler outlet
hose.

Blow compressed air regulated to 5 - 9 kg/cm

(70 - 130 psi)

through the cooler outlet hose for 10 seconds to force out any
remaining fluid.

10. Repeat steps 5 through 9 three additional times.

11. Position an oil pan under the banjo bolts that connect the fluid

cooler steel lines to the transaxle.

12. Remove the banjo bolts.

13. Flush each steel line from the cooler side back toward the tran-

saxle by spraying Transmission Cooler Cleaner in a continuous stream for 5 seconds.

14. Blow compressed air regulated to 5 - 9 kg/cm

(70 - 130 psi) through each steel line from the cooler side

back toward the transaxle for 10 seconds to force out any remaining fluid.

15. Ensure all debris is removed from the steel cooler lines.

16. Ensure all debris is removed from the banjo bolts and fittings.

17. Perform

CVT-18, "CVT FLUID COOLER DIAGNOSIS PROCEDURE"

SCIA4421E

SCIA4422E

SCIA4423E

CVT-18

CVT FLUID

Revision: 2005 August

2005 Murano

CVT FLUID COOLER DIAGNOSIS PROCEDURE

NOTE:
Insufficient cleaning of the cooler inlet hose exterior may lead to inaccurate debris identification.
1.

Position an oil pan under the transaxle's inlet and outlet cooler hoses.

Clean the exterior and tip of the cooler inlet hose.

Insert the extension adapter hose of a can of Transmission
Cooler Cleaner (Nissan P/N 999MP-AM006) into the cooler out-
let hose.

CAUTION:

●

Wear safety glasses and rubber gloves when spraying
the Transmission Cooler Cleaner.

●

Spray cooler cleaner only with adequate ventilation.

●

Avoid contact with eyes and skin.

●

Do not breath vapors or spray mist.

Hold the hose and can as high as possible and spray Transmis-
sion Cooler Cleaner in a continuous stream into the cooler outlet
hose until fluid flows out of the cooler inlet hose for 5 seconds.

Tie a common white, basket-type coffee filter to the end of the
cooler inlet hose.

Insert the tip of an air gun into the end of the cooler outlet hose.

Wrap a shop rag around the air gun tip and end of cooler outlet
hose.

Blow compressed air regulated to 5 - 9 kg/cm

(70 - 130 psi)

through the cooler outlet hose to force any remaining CVT fluid
into the coffee filter.

Remove the coffee filter from the end of the cooler inlet hose.

10. Perform

CVT-19, "CVT FLUID COOLER INSPECTION PROCE-

DURE"

SCIA4421E

SCIA4424E

SCIA4425E

CVT FLUID

CVT-19

CVT

Revision: 2005 August

2005 Murano

CVT FLUID COOLER INSPECTION PROCEDURE

Inspect the coffee filter for debris.

If small metal debris less than 1mm (0.040 in) in size or metal
powder is found in the coffee filter, this is normal. If normal
debris is found, the CVT fluid cooler/radiator can be re-used and
the procedure is ended.

If one or more pieces of debris are found that are over 1mm
(0.040 in) in size and/or peeled clutch facing material is found in
the coffee filter, the fluid cooler is not serviceable. The radiator/
fluid cooler must be replaced and the inspection procedure is
ended.

CVT FLUID COOLER FINAL INSPECTION

After performing all procedures, ensure that all remaining oil is cleaned from all components.

SCIA2967E

SCIA5257E

CVT-20

CVT SYSTEM

Revision: 2005 August

2005 Murano

CVT SYSTEM

PFP:31036

Cross-Sectional View - RE0F09A

ACS0020F

Converter housing

Oil pump

Forward clutch

Reverse brake

Planetary carrier

Primary pulley

Steel belt

Sun gear

Side cover

10. Internal gear

11.

Secondary pulley

12. Final gear

13. Differential case

14. Idler gear

15. Reduction gear

16. Taper roller bearing

17. Output gear

18. Parking gear

19. Input shaft

20. Torque converter

SCIA4837E

Content .. 56 57 58 59 ..