Nissan Murano Z50 (2005 year). Manual - part 55

 

  Index      Manuals     Nissan Murano Z50 (2005 year) - Service and Repair Manual

 

Search            copyright infringement  

 

 

 

 

 

 

 

 

Content      ..     53      54      55      56     ..

 

 

Nissan Murano Z50 (2005 year). Manual - part 55

 

 

TROUBLE DIAGNOSIS

BRC-99

[VDC/TCS/ABS]

C

D

E

G

H

I

J

K

L

M

A

B

BRC

Revision: 2005 August

2005 Murano

Inspection 14 When “DECEL G SEN SET” Appears on Self-Diagnosis Results 
Display

AFS0020H

INSPECTION PROCEDURE

1. 

CHECK SELF DIAGNOSTIC RESULTS (1)

Check self-diagnostic results.

Dose anything besides “DECEL G SEN SET” appear on self-diagnosis results display?

YES

>> Inspect and repair the indicated items. Then perform self-diagnosis again.

NO

>> Perform adjustment of Decel G Sensor neutral position. Then GO TO 2.

2. 

CHECK SELF-DIAGNOSTIC RESULTS (2)

Turn ignition switch OFF, and ON to erase self-diagnosis results, and perform ABS actuator and electric unit
(control unit) self-diagnosis again.
Dose anything appear on self-diagnosis results display?

YES

>> Replace Yaw rate/side/decel G sensor. Then perform adjustments of neutral position and perform

self-diagnosis again.

NO

>> INSPECTION END.

Inspection 15 When “ESTM VEH SPD SIG” Appears on Self-Diagnosis Results 
Display

AFS0020I

INSPECTION PROCEDURE

1. 

CHECK SELF DIAGNOSTIC RESULTS

Check CVT self-diagnostic results.

Does anything besides “ESTM VEH SPD SIG” appear on self-diagnosis results display?

YES

>> Inspect and repair the indicated items. Then perform self-diagnosis again.

NO

>>

Erase CVT self-diagnosis. The inspection is complete.

NOTE:
If there is no error about ABS actuator and electric unit (control unit), “ESTM VHE SPD SIG”
may be displayed in CVT self-diagnosis depending no the timing of cranking.

Inspection 16 VDC OFF Indicator Lamp Does Not Illuminate

AFS0020J

INSPECTION PROCEDURE

1. 

CHECK VDC OFF INDICATOR LAMP

Disconnect ABS actuator and electric unit (control unit) connector E24.

Do ABS warning lamp and VDC OFF indicator lamp illuminate?

OK

>> Malfunction in combination meter system. Inspect combination meter.

NG

>> Malfunction of ABS actuator and electric unit (control unit). Repair or replace control unit.

Self-diagnostic results

DECEL G SEN SET

Self-diagnostic results

ESTM VEH SPD SIG

BRC-100

[VDC/TCS/ABS]

TROUBLE DIAGNOSIS

Revision: 2005 August

2005 Murano

Component Inspection

AFS0020K

VDC OFF SWITCH

Turn ignition switch OFF, and disconnect the VDC OFF switch
connector M17, and check continuity between terminals 1 and 2.

Symptom 1 Excessive ABS Function Operation Frequency

AFS0020L

1. 

CHECK WHEEL SENSOR

Wheel Sensor Inspection

Sensor mount and damage inspection

Sensor rotor mount and damage inspection

Sensor connector connection inspection

Sensor harness inspection

OK or NG

OK

>> GO TO 2.

NG

>> Replace sensor or sensor rotor.

2. 

CHECK FRONT AND REAR AXLE

Make sure there is no excessive play in front and rear axles.
OK or NG

OK

>> GO TO 3.

NG

>> Repair.

3. 

CHECK ABS WARNING LAMP DISPLAY

Make sure ABS warning lamp turns OFF after ignition switch is turned on or when driving.

OK or NG

OK

>> Normal

NG

>> Perform self-diagnosis. Refer to 

BRC-72, "SELF-DIAGNOSIS"

 .

Symptom 2 Unexpected Pedal Reaction

AFS0020M

1. 

CHECK BRAKE PEDAL STROKE

Check brake pedal stroke.
Is the stroke too long?

YES

>>

Bleed air from the brake piping.

Check the brake pedal, brake booster, and master cylinder mount for play, looseness, and
brake system for fluid leaks, etc. If any malfunctions are found, make repair.

NO

>> GO TO 2.

2. 

CHECK PEDAL FORCE

Make sure that brake is effective with pedal depressed.

Is pedal heavy, but affective?

YES

>> Normal

NO

>> GO TO 3.

1 -2

: Continuity should exist when pushing the 
switch.
Continuity should not exist when releasing 
the switch.

PFIA0307E

TROUBLE DIAGNOSIS

BRC-101

[VDC/TCS/ABS]

C

D

E

G

H

I

J

K

L

M

A

B

BRC

Revision: 2005 August

2005 Murano

3. 

CHECK PERFORMANCE 

Disconnect ABS actuator and electric unit (control unit) connector E24 and make sure the braking force us
sufficient when ABS in not operating. After the inspection, reconnect connector.

OK or NG

OK

>> GO TO 4.

NG

>> Check brake system.

4. 

CHECK ABS WARNING LAMP DISPLAY

Make sure ABS warning lamp turns OFF after ignition switch is turned ON or when driving.

OK or NG

OK

>> Normal

NG

>> GO TO 5

5. 

CHECK WHEEL SENSOR

Wheel Sensor Inspection

Sensor mount and damage inspection

Sensor rotor mount and damage inspection

Sensor connector connection inspection

Sensor harness inspection

OK or NG

OK

>> Normal

NG

>> Sensor or sensor rotor replacement

Symptom 3 The Braking Distance Is Long

AFS0020N

CAUTION:

On slippery road surfaces, the stopping distance might be longer with ABS operating than when ABS
is not operating.

1. 

CHECK PERFORMANCE

Disconnect ABS actuator and electric unit (control unit) connector E24 to deactivate ABS. In this condition,
check stopping distance. After inspection, connect connector.
Is stopping distance still long?

YES

>>

Bleed air from the brake piping.

Check brake system.

NO

>> GO TO 2.

2. 

CHECK ABS WARNING LAMP DISPLAY

Make sure ABS warning lamp turns OFF after ignition switch is turned ON or when driving.
OK or NG

OK

>> Normal

NG

>> GO TO 3.

BRC-102

[VDC/TCS/ABS]

TROUBLE DIAGNOSIS

Revision: 2005 August

2005 Murano

3. 

CHECK WHEEL SENSOR

Wheel Sensor Inspection

Sensor mount and damage inspection

Sensor rotor mount and damage inspection

Sensor connector connection inspection

Sensor harness inspection

OK or NG

OK

>> Normal

NG

>> Replace sensor or sensor rotor.

Symptom 4 ABS Function Does Not Operate

AFS0020O

CAUTION:

ABS does not operate when vehicle speed is 10 km/h (6 MPH) or less.

1. 

CHECK ABS WARNING LAMP DISPLAY

Make sure ABS warning lamp turns OFF after ignition switch is turned on or when driving.

OK or NG

OK

>> GO TO 2.

NG

>> Perform self-diagnosis. Refer to 

BRC-72, "SELF-DIAGNOSIS"

 . 

2. 

CHECK WHEEL SENSOR

Wheel Sensor Inspection

Sensor mount and damage inspection

Sensor rotor mount and damage inspection

Sensor connector connection inspection

Sensor harness inspection

OK or NG

OK

>> Normal

NG

>> Replace sensor or sensor rotor.

Symptom 5 Pedal Vibration or ABS Operation Sound Occurs

AFS0020P

CAUTION:

Under the following conditions, when brake pedal is lightly depressed (just place a foot on it), ABS is
activated and vibration is felt. However, this is normal.

When shifting gears

When driving on slippery road

During cornering at high speed

When passing over bumps or grooves

When pulling away just after starting engine [at approximately 10 km/h (6 MPH) or higher]

1. 

SYMPTOM CHECK 1

Check if pedal vibration or operation sound occurs when engine is started.

OK or NG

OK

>> Perform self-diagnosis. Refer to 

BRC-72, "SELF-DIAGNOSIS"

 .

NG

>> GO TO 2.

TROUBLE DIAGNOSIS

BRC-103

[VDC/TCS/ABS]

C

D

E

G

H

I

J

K

L

M

A

B

BRC

Revision: 2005 August

2005 Murano

2. 

INSPECTION (1)

Does vibration occur during normal parking?

CAUTION:

In addition to activation for sudden braking, ABS may activate in conditions such as those listed 
below.

Roads with low surface

Turning at high speed

Passing through gusts of wind

OK or NG

OK

>> GO TO 3.

NG

>> Normal

3. 

INSPECTION (2)

Check for vibration when engine speed is increased while vehicle is stopped.

OK or NG

OK

>> GO TO 4

NG

>>

Normal

CAUTION:

Vibration may occur when vehicle is stopped.

4. 

INSPECTION (3)

Check for vibration when switches of electrical components are operated.

OK or NG

OK

>> Check for any wireless devices, or antenna lead near control unit (including wiring).

NG

>> GO TO 5.

5. 

CHECKING ABS WARNING LAMP INDICATION

Confirm ABS warning lamp turns on.

OK or NG

OK

>> Perform self-diagnosis.

NG

>> GO TO 6.

6. 

CHECK WHEEL SENSORS

Inspect wheel sensor system.

Sensor mounting inspection.

Sensor pick-up inspection for iron chips.

Sensor connector engagement inspection.

Inspection of wheel sensor circuit.

OK of NG

OK

>> Normal

NG

>> Repair wheel sensor and sensor rotor system.

Symptom 6 Vehicle Jerks During VDC/TCS/ABS Control

AFS0020Q

1. 

CHECK ENGINE SPEED SIGNAL

Perform CONSULT-II ABS actuator and electric unit (control unit) “Data Monitor”.

Is engine speed at idle 400 rpm or higher?

YES

>> Normal.

NO

>> GO TO 2.

BRC-104

[VDC/TCS/ABS]

TROUBLE DIAGNOSIS

Revision: 2005 August

2005 Murano

2. 

CHECK ABS WARNING LAMP DISPLAY

Make sure ABS warning lamp turns OFF after ignition switch is turned on or when driving.

OK or NG

OK

>> GO TO 3.

NG

>> Perform self-diagnosis. Refer to 

BRC-72, "SELF-DIAGNOSIS"

 .

3. 

CHECK ECM SELF-DIAGNOSIS RESULT ITEM

Perform ECM self-diagnosis.

Are self-diagnosis items displayed?

YES

>> Check the corresponding items. Refer to 

EC-94, "TROUBLE DIAGNOSIS"

      in  “Engine Control

(EC section)”.

NO

>> GO TO 4.

4. 

CHECK CVT SELF-DIAGNOSIS RESULTS ITEM

Perform CVT self-diagnosis.

OK or NG

OK

>> GO TO 6.

NG

>> Check the corresponding items. Refer to 

CVT-33, "TROUBLE DIAGNOSIS"

   in “CVT”.

5. 

SELF-DIAGNOSIS RESULT ITEM INSPECTION 1

Perform self-diagnosis of ABS actuator and electric unit (control unit).

Are self-diagnosis items displayed?

YES

>> Check the corresponding items, make repairs, and perform ABS actuator and electric unit (control

unit) self-diagnosis again.

NO

>> GO TO 7.

6. 

CHECK CONNECTOR

1.

Disconnect ABS actuator and electric unit (control unit) E24 and the ECM connector, check terminals for
deformation, disconnection, looseness, and so on. If there is an error, repair or replace connector.

2.

Securely reconnect connector and perform self-diagnosis.

OK or NG

OK

>> If connector terminal contact is loose, damaged, open or shorted, repair or replace connector ter-

minal.

NG

>> GO TO 7.

7. 

SELF-DIAGNOSIS RESULT ITEM INSPECTION 2

Perform the self-diagnosis.

Are self-diagnosis items displayed?

YES

>> Repair or replace any malfunction items.

NO

>> GO TO 8.

8. 

CHECK CIRCUIT BETWEEN ABS ACTUATOR AND ELECTRIC UNIT (CONTROL UNIT) AND ECM

Check CAN communication system. Refer to 

BRC-98, "Inspection 13 CAN Communication Circuit"

 .

OK or NG

OK

>> INSPECTION END

NG

>> Connect connectors, and perform ABS actuator and electric unit (control unit) self-diagnosis.

WHEEL SENSORS

BRC-105

[VDC/TCS/ABS]

C

D

E

G

H

I

J

K

L

M

A

B

BRC

Revision: 2005 August

2005 Murano

WHEEL SENSORS

PFP:47910

Removal and Installation

AFS0020R

REMOVAL

Pay attention to the following when removing wheel sensor.

CAUTION:

As much as possible, avoid rotating wheel sensor when removing it. Pull wheel sensors out with-
out pulling on sensor harness.

Take care to avoid damaging wheel sensor edges or rotor teeth. Remove wheel sensor first before
removing front or rear wheel hub. This is to avoid damage to wheel sensor wiring and loss of sen-
sor function.

INSTALLATION

Pay attention to the following when installing wheel sensor. Tighten installation bolts and nuts to the specified
torques.

When installing, make sure there is no foreign material such as iron chips on and in the mounting hole of
the wheel sensor. Make sure no foreign material has been caught in the sensor rotor. Remove any foreign
material and clean the mount.

When installing wheel sensor, be sure to press rubber grommets in until they lock at locations shown
above in figure. When installed, harness must not be twisted. 

PFIA0417E

BRC-106

[VDC/TCS/ABS]

SENSOR ROTOR

Revision: 2005 August

2005 Murano

SENSOR ROTOR

PFP:47970

Removal and Installation

AFS0020S

REMOVAL
Front

Sensor rotor cannot be disassembled. To replace sensor rotor, replace hub bearing assembly. Refer to 

FAX-5,

"FRONT WHEEL HUB AND KNUCKLE"

   in “FAX” section.

Rear

Sensor rotor cannot be disassembled. To replace sensor rotor, replace hub bearing assembly. Refer to 

RAX-5,

"WHEEL HUB"

   in “RAX” section.

INSTALLATION
Front

Sensor rotor cannot be disassembled. To replace sensor rotor, replace hub bearing assembly. Refer to 

FAX-5,

"FRONT WHEEL HUB AND KNUCKLE"

   in “FAX” section.

Rear

Sensor rotor cannot be disassembled. To replace sensor rotor, replace hub bearing assembly. Refer to 

RAX-5,

"WHEEL HUB"

   in “RAX” section.

ACTUATOR AND ELECTRIC UNIT (ASSEMBLY)

BRC-107

[VDC/TCS/ABS]

C

D

E

G

H

I

J

K

L

M

A

B

BRC

Revision: 2005 August

2005 Murano

ACTUATOR AND ELECTRIC UNIT (ASSEMBLY)

PFP:47660

Removal and Installation

AFS001ZU

Pay attention to the following when removing actuator.

CAUTION:

If the part number on the part number label (pasted on actuator upper surface) is the same, ABS
actuator and electric unit (control unit) (integrated in control unit, part No. : 47660 *****) can not be
used on another vehicle.
If it is used on another vehicle, ABS warning lamp, SLIP indicator lamp, VDC OFF indicator lamp
may turn ON or VDC/TCS/ABS may not operate normally.
When replacing ABS actuator and electric unit (control unit) (integrated in control unit), must use
new service parts.

Before servicing, disconnect battery cables.

To remove brake tube, use flare nut torque wrench to prevent flare nuts and brake tube from being
damaged. To install, use flare nut wrench (commercial service tool).

Do not remove and install actuator by holding harness.

After work is completed, bleed air from brake piping. Refer to 

BR-12, "Bleeding Brake System"

 .

NOTE:

After performing above works, calibrate decel G sensor (AWD model). Refer to 

BRC-50, "Calibration of

Decel G Sensor"

 . 

PFIA0418E

1.

To front left

2.

To rear right

3.

To rear left

4.

To front right

5.

From master cylinder secondary 
side

6.

From master cylinder primary side

7.

ABS actuator and electric unit (con-
trol unit)

8.

Harness connector

BRC-108

[VDC/TCS/ABS]

ACTUATOR AND ELECTRIC UNIT (ASSEMBLY)

Revision: 2005 August

2005 Murano

In the case that ABS actuator and electric unit (control unit) are replaced, make sure to adjust position of
steering angle sensor. Refer to 

BRC-49, "Adjustment of Steering Angle Sensor Neutral Position"

 .

G SENSOR

BRC-109

[VDC/TCS/ABS]

C

D

E

G

H

I

J

K

L

M

A

B

BRC

Revision: 2005 August

2005 Murano

G SENSOR

PFP:47930

Removal and Installation

AFS001BY

REMOVAL

1.

Remove center console. Refer to 

IP-17, "CENTER CONSOLE

ASSEMBLY"

  .

2.

Disconnect harness connector.

3.

Remove installation nuts. Remove yaw rate/side/decel G sen-
sor.

CAUTION:

Do not drop or strike the yaw rate/side/decel G sensor,
because it has little endurance to impact.

Do not use power tool etc., because yaw rate/side/decel G
sensor is weak for the impact.

INSTALLATION

Installation is in the revers order of removal.

CAUTION:

Do not drop or strike the yaw rate/side/decel G sensor, because it has little endurance to impact.

NOTE:

After performing above work, calibrate decel G sensor (AWD model). Refer to 

BRC-50, "Calibration of

Decel G Sensor"

  .

PFIA0450E

BRC-110

[VDC/TCS/ABS]

STEERING ANGLE SENSOR

Revision: 2005 August

2005 Murano

STEERING ANGLE SENSOR

PFP:25554

Removal and Installation

AFS00212

Refer to 

SRS-38, "SPIRAL CABLE"

  .

NOTE:

Steering angle sensor is built into the spiral cable.

In the case that ABS actuator and electric unit (control unit) are replaced, make sure to adjust position of
steering angle sensor. Refer to 

BRC-49, "Adjustment of Steering Angle Sensor Neutral Position"

  .

CO-1

ENGINE COOLING SYSTEM

B  ENGINE

CONTENTS

C

D

E

F

G

H

I

J

K

L

M

SECTION 

CO

A

CO

Revision: 2005 August

2005 Murano

ENGINE COOLING SYSTEM

PRECAUTIONS .......................................................... 2

Precautions for Supplemental Restraint System 
(SRS) “AIR BAG” and “SEAT BELT PRE-TEN-
SIONER” .................................................................. 2
Precautions for Liquid Gasket  .................................. 2

REMOVAL OF LIQUID GASKET SEALING .......... 2
LIQUID GASKET APPLICATION PROCEDURE 

..... 2

PREPARATION ........................................................... 4

Special Service Tools  ............................................... 4
Commercial Service Tools ........................................ 4

OVERHEATING CAUSE ANALYSIS .......................... 5

Troubleshooting Chart .............................................. 5

COOLING SYSTEM .................................................... 7

Cooling Circuit .......................................................... 7
System Chart  ........................................................... 8

ENGINE COOLANT .................................................... 9

Inspection ................................................................. 9

LEVEL CHECK  ..................................................... 9
LEAK CHECK  ....................................................... 9

Changing Engine Coolant  ........................................ 9

DRAINING ENGINE COOLANT  ........................... 9
REFILLING ENGINE COOLANT  ........................ 10
FLUSHING COOLING SYSTEM ..........................11

RADIATOR ................................................................ 13

Removal and Installation  ........................................ 13

REMOVAL ........................................................... 13
INSTALLATION ................................................... 14
INSPECTION AFTER INSTALLATION  ............... 14

Checking Radiator Cap  .......................................... 15
Checking Radiator .................................................. 15

RADIATOR (ALUMINUM TYPE)  .............................. 16

Disassembly and Assembly  ................................... 16

PREPARATION ................................................... 16
DISASSEMBLY ................................................... 16
ASSEMBLY ......................................................... 17
INSPECTION ...................................................... 19

COOLING FAN .......................................................... 20

Removal and Installation  ........................................ 20

REMOVAL ........................................................... 20
INSTALLATION ................................................... 20
INSPECTION AFTER INSTALLATION ................ 20

Disassembly and Assembly .................................... 21

DISASSEMBLY ................................................... 21
INSPECTION AFTER DISASSEMBLY ................ 21
ASSEMBLY ......................................................... 21

WATER PUMP  .......................................................... 22

Removal and Installation  ........................................ 22

REMOVAL ........................................................... 22
INSPECTION AFTER REMOVAL  ....................... 24
INSTALLATION ................................................... 24
INSPECTION AFTER INSTALLATION ................ 26

WATER INLET AND THERMOSTAT ASSEMBLY .... 27

Removal and Installation  ........................................ 27

REMOVAL ........................................................... 27
INSPECTION AFTER REMOVAL  ....................... 28
INSTALLATION ................................................... 28
INSPECTION AFTER INSTALLATION ................ 28

WATER OUTLET AND WATER PIPING ................... 29

Removal and Installation  ........................................ 29

REMOVAL ........................................................... 29
INSTALLATION ................................................... 30
INSPECTION AFTER INSTALLATION ................ 30

SERVICE DATA AND SPECIFICATIONS (SDS)  ...... 31

Standard and Limit .................................................. 31

ENGINE COOLANT CAPACITY (APPROXI-
MATE) .................................................................. 31
RADIATOR .......................................................... 31
THERMOSTAT .................................................... 31

CO-2

PRECAUTIONS

Revision: 2005 August

2005 Murano

PRECAUTIONS

PFP:00001

Precautions for Supplemental Restraint System (SRS) “AIR BAG” and “SEAT 
BELT PRE-TENSIONER”

ABS004RH

The Supplemental Restraint System such as “AIR BAG” and “SEAT BELT PRE-TENSIONER”, used along
with a front seat belt, helps to reduce the risk or severity of injury to the driver and front passenger for certain
types of collision. This system includes seat belt switch inputs and dual stage front air bag modules. The SRS
system uses the seat belt switches to determine the front air bag deployment, and may only deploy one front
air bag, depending on the severity of a collision and whether the front occupants are belted or unbelted.
Information necessary to service the system safely is included in the SRS and SB section of this Service Man-
ual.

WARNING:

To avoid rendering the SRS inoperative, which could increase the risk of personal injury or death
in the event of a collision which would result in air bag inflation, all maintenance must be per-
formed by an authorized NISSAN/INFINITI dealer.

Improper maintenance, including incorrect removal and installation of the SRS, can lead to per-
sonal injury caused by unintentional activation of the system. For removal of Spiral Cable and Air
Bag Module, see the SRS section.

Do not use electrical test equipment on any circuit related to the SRS unless instructed to in this
Service Manual. SRS wiring harnesses can be identified by yellow and/or orange harnesses or
harness connectors.

Precautions for Liquid Gasket

ABS004RI

REMOVAL OF LIQUID GASKET SEALING

After removing mounting bolts and nuts, separate the mating
surface using the seal cutter [SST] and remove old liquid gasket
sealing.     

CAUTION:

Be careful not to damage the mating surfaces.

Tap seal cutter to insert it, and then slide it by tapping on the
side as shown in the figure.

In areas where seal cutter is difficult to use, use a plastic ham-
mer to lightly tap the parts, to remove it.

CAUTION:

If for some unavoidable reason tool such as a screwdriver
is used, be careful not to damage the mating surfaces.

LIQUID GASKET APPLICATION PROCEDURE

1.

Using a scraper, remove old liquid gasket adhering to the liquid
gasket application surface and the mating surface.

Remove liquid gasket completely from the groove of the liquid
gasket application surface, mounting bolts, and bolt holes.

2.

Wipe the liquid gasket application surface and the mating sur-
face with white gasoline (lighting and heating use) to remove
adhering moisture, grease and foreign materials.

PBIC0002E

PBIC0003E

PRECAUTIONS

CO-3

C

D

E

F

G

H

I

J

K

L

M

A

CO

Revision: 2005 August

2005 Murano

3.

Attach liquid gasket tube to the tube presser [SST: WS39930000
(

)].

Use Genuine RTV Silicone Sealant or equivalent. Refer to

GI-47, "RECOMMENDED CHEMICAL PRODUCTS AND
SEALANTS"

 .

4.

Apply liquid gasket without breaks to the specified location with
the specified dimensions.

If there is a groove for the liquid gasket application, apply liq-
uid gasket to the groove.

As for the bolt holes, normally apply liquid gasket inside the
holes. Occasionally, it should be applied outside the holes.
Make sure to read the text of service manual.

Within five minutes of liquid gasket application, install the mat-
ing component.

If liquid gasket protrudes, wipe it off immediately.

Do not retighten after the installation.

After 30 minutes or more have passed from the installation, fill
engine oil and engine coolant.

CAUTION:

If there are specific instructions in this manual, observe them.

EMA0622D

SEM159F

CO-4

PREPARATION

Revision: 2005 August

2005 Murano

PREPARATION

PFP:00002

Special Service Tools

ABS0035A

The actual shapes of Kent-Moore tools may from those of special service tools illustrated here.

Commercial Service Tools

ABS0035B

Tool number
(Kent-Moore No.)
Tool name

Description

EG17650301
(J33984-A)
Radiator cap tester adapter

Adapting radiator cap tester to radiator cap 
and radiator filler neck
a: 28 (1.10) dia.
b: 31.4 (1.236) dia.
c: 41.3 (1.626) dia.
Unit: mm (in)

KV99103510
(

)

Radiator plate pliers A

Installing radiator upper and lower tanks

KV99103520
(

)

Radiator plate pliers B

Removing radiator upper and lower tanks

WS39930000
(

)

Tube pressure

Pressing the tube of liquid gasket

S-NT564

S-NT224

S-NT225

S-NT052

Tool name

Description

Power tool

Loosening nuts and bolts

Radiator cap tester

Checking radiator and radiator cap

PBIC0190E

PBIC1982E

 

 

 

 

 

 

 

Content      ..     53      54      55      56     ..