Nissan Murano Z50 (2005 year). Manual - part 6

 

  Index      Manuals     Nissan Murano Z50 (2005 year) - Service and Repair Manual

 

Search            copyright infringement  

 

 

 

 

 

 

 

 

Content      ..     4      5      6      7     ..

 

 

Nissan Murano Z50 (2005 year). Manual - part 6

 

 

TROUBLE DIAGNOSIS

ATC-57

C

D

E

F

G

H

I

K

L

M

A

B

ATC

Revision: 2005 August

2005 Murano

CHECKING INTAKE AIR

1.

Press recirculation (REC) switch. Recirculation indicator should
illuminate.

2.

Press fresh (FRE) switch one time. Fresh indicator should illumi-
nate. 

3.

Listen for intake door position change. (Slight change of blower
sound can be heard.) 

If NG, go to trouble diagnosis procedure for 

ATC-71, "Intake Door

Motor Circuit"

 .

If OK, continue the check.

NOTE:
Confirm that the compressor clutch is engaged (sound or visual
inspection) and intake door position is at FRESH when the DEF or D/F is selected.

CHECKING TEMPERATURE DECREASE

1.

Turn temperature control dial (driver side) counterclockwise until
18

°

C (60

°

F) is displayed.

2.

Check for cold air at discharge air outlets.

If NG, go to trouble diagnosis procedure for 

ATC-85, "Insufficient

Cooling"

 .

If OK, continue the check.

CHECKING TEMPERATURE INCREASE

1.

Turn temperature control dial (driver side) clockwise until 32

°

C

(90

°

F) is displayed.

2.

Check for hot air at discharge air outlets.

If NG, go to trouble diagnosis procedure for 

ATC-93, "Insufficient

Heating"

 .

If OK, continue the check.

CHECK A/C SWITCH

1.

Press AUTO switch and A/C switch.

2.

A/C switch indicator will turn ON.

Confirm that the compressor clutch engages (sound or visual
inspection).

If NG, go to trouble diagnosis procedure for 

ATC-79, "Magnet Clutch

Circuit"

 .

If OK, continue the check.

RJIA1768E

RJIA1769E

RJIA1770E

RJIA2099E

ATC-58

TROUBLE DIAGNOSIS

Revision: 2005 August

2005 Murano

CHECKING AUTO MODE

1.

Press AUTO switch and A/C switch.

2.

Display should indicate AUTO.

Confirm that the compressor clutch engages (sound or visual
inspection). (Discharge air and blower speed will depend on
ambient, in-vehicle, and set temperatures.)

If NG, go to trouble diagnosis procedure for 

ATC-58, "Power Supply

and Ground Circuit for Auto Amp."

 , then if necessary, trouble diag-

nosis procedure fo

ATC-79, "Magnet Clutch Circuit"

 .

If all operational checks are OK (symptom cannot be duplicated), go
to Malfunction Simulation Tests in 

GI-27, "How to Perform Efficient

Diagnosis for an Electrical Incident"

  and perform tests as outlined to

simulate driving conditions environment. If symptom appears, refer
to 

ATC-37, "SYMPTOM TABLE"

  and perform applicable trouble diagnosis procedures.

Power Supply and Ground Circuit for Auto Amp.

AJS000Z5

SYMPTOM: A/C system does not come on.

INSPECTION FLOW

RJIA1771E

*1

ATC-59, "DIAGNOSIS PROCE-
DURE FOR A/C SYSTEM"

*2

ATC-56, "Operational Check"

*3

AV-94, "Trouble Diagnosis Chart by 
Symptom"

*4

AV-166, "A/C and AV Switch Self-
Diagnosis Function"

RJIA1772E

TROUBLE DIAGNOSIS

ATC-59

C

D

E

F

G

H

I

K

L

M

A

B

ATC

Revision: 2005 August

2005 Murano

COMPONENT DESCRIPTION
Unified Meter and A/C Amp. (Automatic Amplifier)

The unified meter and A/C amp. has a built-in microcomputer which
processes information sent from various sensors needed for air con-
ditioner operation. The air mix door motor, mode door motor, intake
door motor, blower motor and compressor are then controlled.
When the various switches and temperature dials are operated, data
is input to the unified meter and A/C amp. from the DISPLAY UNIT/
DISPLAY CONTROL UNIT using CAN communication. 
Self-diagnosis functions are also built into unified meter and A/C
amp. to provide quick check of malfunctions in the auto air condi-
tioner system.

Potentio Temperature Control (PTC)

The PTC is built into the A/C and AV switch. It can be set at an inter-
val of 0.5

°

C (1.0

°

F) in the 18

°

C (60

°

F) to 32

°

C (90

°

F) temperature

range by turning temperature control dial. The set temperature is dis-
played.

DIAGNOSIS PROCEDURE FOR A/C SYSTEM

SYMPTOM: A/C system does not come on.

RJIA1758E

RJIA1773E

SJIA0301E

ATC-60

TROUBLE DIAGNOSIS

Revision: 2005 August

2005 Murano

1. 

CHECK POWER SUPPLY CIRCUIT FOR UNIFIED METER AND A/C AMP.

1.

Disconnect unified meter and A/C amp. connector.

2.

Check voltage between unified meter and A/C amp. harness
connector M50 terminals 21 (Y/R), 22 (G) and 35 (P/B), unified
meter and A/C amp. harness connector M51 terminal 46 (W/L)
and ground.

OK or NG

OK

>> GO TO 2.

NG

>> Check 10 A and 15 A fuses [Nos. 6, 10, 11, 12 and 19, located in the fuse block (J/B)]. Refer to 

PG-70, "FUSE BLOCK - JUNCTION BOX (J/B)"

 .

If fuses are OK, check harness for open circuit. Repair or replace if necessary.

If fuses are NG, replace fuse and check harness for short circuit. Repair or replace if necessary.

2. 

CHECK GROUND CIRCUIT FOR UNIFIED METER AND A/C AMP.

1.

Turn ignition switch OFF.

2.

Check continuity between unified meter and A/C amp. harness
connector M50 terminal 29 (B), 30 (B) and ground.

OK or NG

OK

>> Replace unified meter and A/C amp.

NG

>> Repair harness or connector.

Terminals

Ignition switch position

(+)

(–)

OFF

ACC

ON

Unified meter 

and A/C amp. 

connector 

Terminal 

No.

(wire color)

M50

21 (Y/R)

Ground

Battery 
voltage

Battery 
voltage

Battery 
voltage

M50

22 (G)

Approx. 0 V

Approx. 0 V

Battery 
voltage

M50

35 (P/B)

Approx. 0 V

Battery 
voltage

Battery 
voltage

M51

46 (W/L)

Approx. 0 V

Approx. 0 V

Battery 
voltage

RJIA1984E

29, 30 – Ground

: Continuity should exist.

RJIA1985E

TROUBLE DIAGNOSIS

ATC-61

C

D

E

F

G

H

I

K

L

M

A

B

ATC

Revision: 2005 August

2005 Murano

LAN System Circuit

AJS000Z6

SYMPTOM: Mode door motor, intake door motor and/or air mix door motor(s) does not operate normally.

DIAGNOSIS PROCEDURE FOR LAN CIRCUIT

1. 

CHECK POWER SUPPLY FOR UNIFIED METER AND A/C AMP. 

1.

Turn ignition switch ON.

2.

Check voltage between unified meter and A/C amp. harness
connector M51 terminal 54 (L/W) and ground.

OK or NG

OK

>> GO TO 2.

NG

>> Replace unified meter and A/C amp.

RJIA1775E

54 – Ground

: Battery voltage

RJIA1986E

ATC-62

TROUBLE DIAGNOSIS

Revision: 2005 August

2005 Murano

2. 

CHECK SIGNAL FOR UNIFIED METER AND A/C AMP. 

Confirm A/C LAN signal between unified meter and A/C amp. har-
ness connector M51 terminal 43 (L/B) and ground using an oscillo-
scope.

OK or NG

OK

>> GO TO 3.

NG

>> Replace unified meter and A/C amp.

3. 

CHECK POWER SUPPLY FOR EACH DOOR MOTOR

Check voltage between each door motor harness connector terminal
1 (L/W) and ground.

OK or NG

OK

>> GO TO 4.

NG

>> Repair harness or connector.

4. 

CHECK SIGNAL FOR EACH DOOR MOTOR

Confirm A/C LAN signal between each door motor harness connec-
tor terminal 3 (L/B) and ground using an oscilloscope.

OK or NG

OK

>> GO TO 5.

NG

>> Repair harness or connector.

Terminals

Voltage

(+)

(–)

Unified meter 

and A/C amp. 

connector

Terminal No.

(wire color)

M51

43 (L/B)

Ground

RJIA1987E

HAK0652D

1 – Ground

: Battery voltage

RJIA1988E

Door motor

Terminals

Voltage

(+)

(–)

Connector

Terminal 

No.

(wire color)

Mode

M252

3 (L/B)

Ground

Air mix 
(Driver 
side)

M253

3 (L/B)

Air mix 
(Passen-
ger side)

M254

3 (L/B)

Intake

M255

3 (L/B)

RJIA1989E

HAK0652D

TROUBLE DIAGNOSIS

ATC-63

C

D

E

F

G

H

I

K

L

M

A

B

ATC

Revision: 2005 August

2005 Murano

5. 

CHECK MOTOR GROUND CIRCUIT

1.

Turn ignition switch OFF.

2.

Disconnect door motor connector.

3.

Check continuity between each door motor harness connector
terminal 2 (B) and ground.

OK or NG

OK

>> GO TO 6.

NG

>> Repair harness or connector.

6. 

CHECK MOTOR OPERATION

1.

Reconnect each door motor connector.

2.

Turn ignition switch ON.

3.

Confirm operation of each door motor.

OK or NG

OK

>> (Return to operate normally.)

Poor contact in motor connector.

NG

>> (Does not operate normally.)

GO TO 7.

7. 

CHECK OPERATION OF AIR MIX DOOR MOTOR AND INTAKE DOOR MOTOR

1.

Turn ignition switch OFF.

2.

Disconnect mode door motor, air mix door motor (driver side, passenger side), and intake door motor con-
nectors.

3.

Reconnect air mix door motor (driver side, passenger side) and intake door motor connectors.

4.

Turn ignition switch ON.

5.

Confirm air mix door motor (driver side, passenger side) and intake door motor.

OK or NG

OK

>> [Air mix (driver side, passenger side) and intake door motors operate normally.]

Replace mode door motor.

NG

>> [Air mix (driver side, passenger side) and intake door motors does not operate normally.]

GO TO 8.

8. 

CHECK OPERATION OF MODE DOOR MOTOR AND INTAKE DOOR MOTOR

1.

Turn ignition switch OFF.

2.

Disconnect air mix door motor (driver side, passenger side) connectors.

3.

Reconnect mode door motor connector.

4.

Turn ignition switch ON.

5.

Confirm mode door motor and intake door motor.

OK or NG

OK

>> (Mode and intake door motors operate normally.)

GO TO 10.

NG

>> (Mode and intake door motors does not operate normally.)

GO TO 9.

2 – Ground

: Continuity should exist.

RJIA1990E

ATC-64

TROUBLE DIAGNOSIS

Revision: 2005 August

2005 Murano

9. 

CHECK OPERATION OF MODE DOOR MOTOR AND AIR MIX DOOR MOTOR

1.

Turn ignition switch OFF.

2.

Disconnect intake door motor connector.

3.

Reconnect air mix door motor (driver side, passenger side) connectors. 

4.

Turn ignition switch ON.

5.

Confirm mode door motor and air mix door motor (driver side, passenger side).

OK or NG

OK

>> [Mode and air mix door motor (driver side, passenger side) operate normally.]

Replace intake door motor.

NG

>> [Mode and air mix door motor (driver side, passenger side) does not operate normally.]

Replace display and A/C auto amp.

10. 

CHECK OPERATION OF AIR MIX DOOR MOTOR

1.

Turn ignition switch OFF.

2.

Disconnect air mix door motor (driver side) connector.

3.

Turn ignition switch ON.

4.

Confirm air mix door motor (passenger side).

OK or NG

OK

>> [Air mix door motor (passenger side) operates normally.]

Replace air mix door motor (driver side).

NG

>> [Air mix door motor (passenger side) does not operate normally.]

Replace air mix door motor (passenger side).

TROUBLE DIAGNOSIS

ATC-65

C

D

E

F

G

H

I

K

L

M

A

B

ATC

Revision: 2005 August

2005 Murano

Mode Door Motor Circuit

AJS000Z7

SYMPTOM:

Air outlet does not change.

Mode door motor does not operate normally.

INSPECTION FLOW

*1

ATC-32, "Discharge Air Flow"

*2

ATC-56, "Operational Check"

*3

ATC-106, "Intake Sensor Circuit"

*4

ATC-49, "FUNCTION CONFIRMA-
TION PROCEDURE"

, see No. 4 to 6.

*5

ATC-97, "Ambient Sensor Circuit"

*6

ATC-100, "In-vehicle Sensor Circuit"

*7

ATC-103, "Sunload Sensor Circuit"

*8

ATC-70, "Air Mix Door Motor PBR 
Circuit"

*9

ATC-49, "FUNCTION CONFIRMA-
TION PROCEDURE"

, see No. 13.

*10

ATC-61, "DIAGNOSIS PROCEDURE 
FOR LAN CIRCUIT"

*11

ATC-67, "Mode Door Motor"

*12

ATC-37, "SYMPTOM TABLE"

SJIA1315E

ATC-66

TROUBLE DIAGNOSIS

Revision: 2005 August

2005 Murano

SYSTEM DESCRIPTION
Component Parts

Mode door control system components are:

Unified meter and A/C amp.

Mode door motor (LCU)

A/C LAN system (PBR built-in mode door motor, intake door motor and air mix door motor)

In-vehicle sensor

Ambient sensor

Sunload sensor

Intake sensor

System Operation

The unified meter and A/C amp. receives data from each of the sensors. The unified meter and A/C amp.
sends air mix door, mode door and intake door opening angle data to the air mix door motor LCU, mode door
motor LCU and intake door motor LCU.
The air mix door motor, mode door motor and intake door motor read their respective signals according to the
address signal. Opening angle indication signals received from the unified meter and A/C amp. and each of
the motor position sensors are compared by the LCUs in each door motor with the existing decision and open-
ing angles. Subsequently, HOT/COLD, DEF/VENT and FRESH/RECIRCULATION operation is selected. The
new selection data are returned to the unified meter and A/C amp.

Mode Door Control Specification

RJIA1777E

RJIA1778E

TROUBLE DIAGNOSIS

ATC-67

C

D

E

F

G

H

I

K

L

M

A

B

ATC

Revision: 2005 August

2005 Murano

COMPONENT DESCRIPTION
Mode Door Motor

The mode door motor is attached to the heater & cooling unit assem-
bly. It rotates so that air is discharged from the outlet set by the uni-
fied meter and A/C amp. Motor rotation is conveyed to a link which
activates the mode door.

DIAGNOSIS PROCEDURE FOR MODE DOOR MOTOR

SYMPTOM: Mode door motor does not operate normally.
Perform diagnosis procedure. Refer to 

ATC-61, "DIAGNOSIS PROCEDURE FOR LAN CIRCUIT"

 .

RJIA1779E

ATC-68

TROUBLE DIAGNOSIS

Revision: 2005 August

2005 Murano

Air Mix Door Motor Circuit

AJS000Z8

SYMPTOM:

Discharge air temperature does not change.

Air mix door motor does not operate normally.

INSPECTION FLOW

*1

ATC-49, "FUNCTION CONFIRMA-
TION PROCEDURE"

, see No. 4 to 6.

*2

ATC-97, "Ambient Sensor Circuit"

*3

ATC-100, "In-vehicle Sensor Circuit"

*4

ATC-103, "Sunload Sensor Circuit"

*5

ATC-70, "Air Mix Door Motor PBR Cir-
cuit"

*6

ATC-49, "FUNCTION CONFIRMA-
TION PROCEDURE"

, see No. 13.

*7

ATC-61, "LAN System Circuit"

*8

ATC-70, "Air Mix Door Motor"

*9

ATC-56, "Operational Check"

*10

ATC-37, "SYMPTOM TABLE"

*11

ATC-106, "Intake Sensor Circuit"

SJIA0525E

TROUBLE DIAGNOSIS

ATC-69

C

D

E

F

G

H

I

K

L

M

A

B

ATC

Revision: 2005 August

2005 Murano

SYSTEM DESCRIPTION
Component Parts

Air mix door control system components are:

Unified meter and A/C amp.

Air mix door motor (LCU)

A/C LAN system (PBR built-in mode door motor, intake door motor and air mix door motor)

In-vehicle sensor

Ambient sensor

Sunload sensor

Intake sensor

System Operation

The unified meter and A/C amp. receives data from each of the sensors. The unified meter and A/C amp.
sends air mix door, mode door and intake door opening angle data to the air mix door motor LCU, mode door
motor LCU and intake door motor LCU.
The air mix door motor, mode door motor and intake door motor read their respective signals according to the
address signal. Opening angle indication signals received from the unified meter and A/C amp. and each of
the motor position sensors are compared by the LCUs in each door motor with the existing decision and open-
ing angles. Subsequently, HOT/COLD, DEF/VENT and FRESH/RECIRCULATION operation is selected. The
new selection data are returned to the unified meter and A/C amp.

Air Mix Door Control Specification

RJIA1781E

RJIA1782E

ATC-70

TROUBLE DIAGNOSIS

Revision: 2005 August

2005 Murano

COMPONENT DESCRIPTION
Air Mix Door Motor

The air mix door motor is attached to the heater & cooling unit
assembly. It rotates so that the air mix door is opened or closed to a
position set by the unified meter and A/C amp. Motor rotation is then
sent conveyed through a shaft and the air mix door position feed-
back is then sent to the unified meter and A/C amp. by PBR built-in
air mix door motor.

DIAGNOSIS PROCEDURE FOR AIR MIX DOOR

SYMPTOM: Discharge air temperature does not change.
Perform diagnosis procedure. Refer to 

ATC-61, "DIAGNOSIS PROCEDURE FOR LAN CIRCUIT"

 .

Air Mix Door Motor PBR Circuit

AJS000Z9

SYMPTOM:

Discharge air temperature does not change.

PBR circuit is open or shorted.

DIAGNOSIS PROCEDURE FOR AIR MIX DOOR MOTOR PBR

Perform diagnosis procedure. Refer to 

ATC-61, "DIAGNOSIS PROCEDURE FOR LAN CIRCUIT"

 .

RJIA1783E

RJIA1784E

TROUBLE DIAGNOSIS

ATC-71

C

D

E

F

G

H

I

K

L

M

A

B

ATC

Revision: 2005 August

2005 Murano

Intake Door Motor Circuit

AJS0010Y

SYMPTOM:

Intake door does not change.

Intake door motor does not operate normally.

INSPECTION FLOW

*1

ATC-49, "FUNCTION CONFIRMA-
TION PROCEDURE"

, see No. 4 to 6.

*2

ATC-97, "Ambient Sensor Circuit"

*3

ATC-100, "In-vehicle Sensor Circuit"

*4

ATC-103, "Sunload Sensor Circuit"

*5

ATC-70, "Air Mix Door Motor PBR 
Circuit"

*6

ATC-49, "FUNCTION CONFIRMA-
TION PROCEDURE"

, see No. 13.

*7

ATC-61, "LAN System Circuit"

*8

ATC-73, "Intake Door Motor"

*9

ATC-56, "Operational Check"

*10

ATC-37, "SYMPTOM TABLE"

*11

ATC-106, "Intake Sensor Circuit"

RJIA1785E

ATC-72

TROUBLE DIAGNOSIS

Revision: 2005 August

2005 Murano

SYSTEM DESCRIPTION
Component Parts

Intake door control system components are:

Unified meter and A/C amp.

Intake door motor (LCU)

A/C LAN system (PBR built-in mode door motor, intake door motor and air mix door motor)

In-vehicle sensor

Ambient sensor

Sunload sensor

Intake sensor

System Operation

The intake door control determines intake door position based on the ambient temperature, the intake air tem-
perature and the in-vehicle temperature. When the DEF, or OFF switches are pressed or A/C switch is OFF,
the unified meter and A/C amp. sets the intake door at the FRESH position.

Intake Door Control Specification

RJIA1786E

RJIA1787E

 

 

 

 

 

 

 

Content      ..     4      5      6      7     ..