Nissan Murano Z50 (2004 year). Manual - part 89

DTC P0456 EVAP CONTROL SYSTEM

EC-335

Revision: 2004 November

2004 Murano

CAUTION:

●

Use only a genuine NISSAN fuel filler cap as a replacement. If an incorrect fuel filler cap is used,
the MIL may come on.

●

If the fuel filler cap is not tightened properly, the MIL may come on.

●

Use only a genuine NISSAN rubber tube as a replacement.

DTC Confirmation Procedure

ABS004HM

NOTE:

●

If DTC P0456 is displayed with P0442, first perform trouble diagnosis for DTC P0456.

●

After repair, make sure that the hoses and clips are installed properly.

●

If DTC Confirmation Procedure has been previously conducted, always turn ignition switch OFF and wait
at least 10 seconds before conducting the next test.

TESTING CONDITION:

●

Open engine hood before conducting following procedure.

●

If any of following conditions are met just before the DTC confirmation procedure, leave the vehi-
cle for more than 1 hour.

–

Fuel filler cap is removed.

–

Refilled or drained the fuel.

–

EVAP component parts is/are removed.

●

Before performing the following procedure, confirm that battery voltage is more than 11V at idle.

WITH CONSULT-II

Turn ignition switch ON and select “DATA MONITOR” mode with CONSULT-II.

Make sure the following conditions are met.
FUEL LEVEL SE: 0.25 - 1.4V
COOLAN TEMP/S: 0 - 32

C (32 - 90

FUEL T/TMP SE: 0 - 35

C (32 - 95

INT A/TEMP SE: More than 0

C (32

If NG, turn ignition switch OFF and leave the vehicle in a cool place (soak the vehicle) or refilling/draining
fuel until the output voltage condition of the “FUEL LEVEL SE” meets within the range above and leave
the vehicle for more than 1 hour. Then start from step 1).

Turn ignition switch OFF and wait at least 10 seconds.

Turn ignition switch ON.

Select “EVAP V/S LEAK P0456/P1456” of “EVAPORATIVE SYSTEM” in “DTC WORK SUPPORT” mode
with CONSULT-II.
Follow the instruction displayed.

Make sure that “OK” is displayed.
If “NG” is displayed, refer to

EC-337, "Diagnostic Procedure"

NOTE:

●

If the engine speed cannot be maintained within the range displayed on CONSULT-II screen, go
to

EC-78, "Basic Inspection"

●

Make sure that EVAP hoses are connected to EVAP canister purge volume control solenoid
valve properly.

PBIB0837E

EC-336

DTC P0456 EVAP CONTROL SYSTEM

Revision: 2004 November

2004 Murano

Overall Function Check

ABS004HN

WITH GST

Use this procedure to check the overall function of the EVAP very small leak function. During this check, a 1st
trip DTC might not be confirmed.

CAUTION:

●

Never use compressed air, doing so may damage the EVAP system.

●

Do not start engine.

●

Do not exceeded 4.12 kPa (0.042 kg/cm

, 0.6 psi).

Attach the EVAP service port adapter securely to the EVAP ser-
vice port.

Set the pressure pump and a hose.

Also set a vacuum gauge via 3-way connector and a hose.

Turn ignition switch ON.

Connect GST and select MODE 8.

Using MODE 8 control the EVAP canister vent control valve
(close).

Apply pressure and make sure the following conditions are sat-
isfied.
Pressure to be applied: 2.7 kPa (20 mmHg, 0.79 inHg)
Time to be waited after the pressure drawn in to the EVAP
system and the pressure to be dropped: 60 seconds and
the pressure should not be dropped more than 0.4 kPa (3 mmHg, 0.12 inHg).
If NG, go to

EC-337, "Diagnostic Procedure"

If OK, go to next step.

Disconnect GST.

Start engine and warm it up to normal operating temperature.

10. Turn ignition switch OFF and wait at least 10 seconds.

11. Restart engine and let it idle for 90 seconds.

12. Keep engine speed at 2,000 rpm for 30 seconds.
13. Turn ignition switch OFF.

NOTE:
For more information, refer to GST instruction manual.

PBIB2090E

SEF462UI

DTC P0456 EVAP CONTROL SYSTEM

EC-337

Revision: 2004 November

2004 Murano

Diagnostic Procedure

ABS004HO

CHECK FUEL FILLER CAP DESIGN

Turn ignition switch OFF.

Check for genuine NISSAN fuel filler cap design.

OK or NG

>> GO TO 2.

>> Replace with genuine NISSAN fuel filler cap.

CHECK FUEL FILLER CAP INSTALLATION

Check that the cap is tightened properly by rotating the cap clockwise.

OK or NG

>> GO TO 3.

>> 1. Open fuel filler cap, then clean cap and fuel filler neck threads using air blower.

2. Retighten until ratcheting sound is heard.

CHECK FUEL FILLER CAP FUNCTION

Check for air releasing sound while opening the fuel filler cap.

OK or NG

>> GO TO 5.

>> GO TO 4.

CHECK FUEL TANK VACUUM RELIEF VALVE

Refer to

EC-654, "FUEL TANK VACUUM RELIEF VALVE (BUILT INTO FUEL FULLER CAP)"

OK or NG

>> GO TO 5.

>> Replace fuel filler cap with a genuine one.

SEF915U

EC-338

DTC P0456 EVAP CONTROL SYSTEM

Revision: 2004 November

2004 Murano

INSTALL THE PRESSURE PUMP

To locate the EVAP leak, install EVAP service port adapter and pres-
sure pump to EVAP service port securely. For the location of EVAP
service port, refer to

EC-652, "EVAPORATIVE EMISSION LINE

DRAWING"

NOTE:
Improper installation of the EVAP service port adapter to the EVAP service port may cause leaking.

With CONSULT-II>>GO TO 6.
Without CONSULT-II>>GO TO 7.

PBIB2090E

SEF916U

DTC P0456 EVAP CONTROL SYSTEM

EC-339

Revision: 2004 November

2004 Murano

CHECK FOR EVAP LEAK

With CONSULT-II

Turn ignition switch ON.

Select “EVAP SYSTEM CLOSE” of “WORK SUPPORT” mode with CONSULT-II.

Touch “START” and apply pressure into the EVAP line until the
pressure indicator reaches the middle of the bar graph.

NOTE:

●

Never use compressed air or a high pressure pump.

●

Do not exceed 4.12 kPa (0.042 kg/cm

, 0.6 psi) of pres-

sure in the system.

Using EVAP leak detector, locate the EVAP leak. For the leak
detector, refer to the instruction manual for more details.
Refer to

EC-652, "EVAPORATIVE EMISSION LINE DRAWING"

OK or NG

>> GO TO 8.

>> Repair or replace.

PEF917U

SEF200U

EC-340

DTC P0456 EVAP CONTROL SYSTEM

Revision: 2004 November

2004 Murano

CHECK FOR EVAP LEAK

Without CONSULT-II

Turn ignition switch OFF.

Apply 12 volts DC to EVAP canister vent control valve. The valve will close. (Continue to apply 12 volts
until the end of test.)

Pressurize the EVAP line using pressure pump with 1.3 to 2.7 kPa (10 to 20 mmHg, 0.39 to 0.79 inHg),
then remove pump and EVAP service port adapter.

NOTE:

●

Never use compressed air or a high pressure pump.

●

Do not exceed 4.12 kPa (0.042 kg/cm

, 0.6 psi) of pressure in the system.

Using EVAP leak detector, locate the EVAP leak. For the leak
detector, refer to the instruction manual for more details. Refer
to

EC-652, "EVAPORATIVE EMISSION LINE DRAWING"

OK or NG

>> GO TO 8.

>> Repair or replace.

CHECK EVAP CANISTER VENT CONTROL VALVE

Check the following.

●

EVAP canister vent control valve is installed properly.
Refer to

EC-655, "Removal and Installation"

●

EVAP canister vent control valve.
Refer to

EC-306, "Component Inspection"

OK or NG

>> GO TO 9.

>> Repair or replace EVAP canister vent control valve and O-ring.

PBIB1365E

SEF200U

DTC P0456 EVAP CONTROL SYSTEM

EC-341

Revision: 2004 November

2004 Murano

CHECK IF EVAP CANISTER SATURATED WITH WATER

Remove EVAP canister with EVAP canister vent control valve and EVAP control system pressure sensor
attached.

Does water drain from the EVAP canister?

Yes or No

Yes

>> GO TO 10.

No (With CONSULT-II)>>GO TO 12.
No (Without CONSULT-II)>>GO TO 13.

10.

CHECK EVAP CANISTER

Weigh the EVAP canister with the EVAP canister vent control valve and EVAP control system pressure sensor
attached.
The weight should be less than 2.1 kg (4.6 lb).

OK or NG

OK (With CONSULT-II)>>GO TO 12.
OK (Without CONSULT-II)>>GO TO 13.
NG

>> GO TO 11.

11.

DETECT MALFUNCTIONING PART

Check the following.

●

EVAP canister for damage

●

EVAP hose between EVAP canister and vehicle frame for clogging or poor connection

>> Repair hose or replace EVAP canister.

12.

CHECK EVAP CANISTER PURGE VOLUME CONTROL SOLENOID VALVE OPERATION

With CONSULT-II

Disconnect vacuum hose to EVAP canister purge volume control solenoid valve at EVAP service port.

Start engine.

Perform “PURG VOL CONT/V” in “ACTIVE TEST” mode.

Touch “Qu” on CONSULT-II screen to increase “PURG VOL
CONT/V” opening to 100%.

Check vacuum hose for vacuum when revving engine up to
2,000 rpm.

OK or NG

>> GO TO 15.

>> GO TO 14.

PBIB1381E

PBIB1678E

EC-342

DTC P0456 EVAP CONTROL SYSTEM

Revision: 2004 November

2004 Murano

13.

CHECK EVAP CANISTER PURGE VOLUME CONTROL SOLENOID VALVE OPERATION

Without CONSULT-II

Start engine and warm it up to normal operating temperature.

Stop engine.

Disconnect vacuum hose to EVAP canister purge volume control solenoid valve at EVAP service port.

Start engine and let it idle for at least 80 seconds.

Check vacuum hose for vacuum when revving engine up to 2,000 rpm.

OK or NG

>> GO TO 16.

>> GO TO 14.

14.

CHECK VACUUM HOSE

Check vacuum hoses for clogging or disconnection. Refer to

EC-23, "Vacuum Hose Drawing"

OK or NG

>> GO TO 15.

>> Repair or reconnect the hose.

15.

CHECK EVAP CANISTER PURGE VOLUME CONTROL SOLENOID VALVE

Refer to

EC-300, "Component Inspection"

OK or NG

>> GO TO 16.

>> Replace EVAP canister purge volume control solenoid valve.

16.

CHECK FUEL TANK TEMPERATURE SENSOR

Refer to

EC-237, "Component Inspection"

OK or NG

>> GO TO 17.

>> Replace fuel level sensor unit.

17.

CHECK EVAP CONTROL SYSTEM PRESSURE SENSOR

Refer to

EC-317, "Component Inspection"

OK or NG

>> GO TO 18.

>> Replace EVAP control system pressure sensor.

18.

CHECK EVAP PURGE LINE

Check EVAP purge line (pipe, rubber tube, fuel tank and EVAP canister) for cracks or improper connection.
Refer to

EC-652, "EVAPORATIVE EMISSION LINE DRAWING"

OK or NG

>> GO TO 19.

>> Repair or reconnect the hose.

19.

CLEAN EVAP PURGE LINE

Clean EVAP purge line (pipe and rubber tube) using air blower.

>> GO TO 20.

Vacuum should exist.

DTC P0456 EVAP CONTROL SYSTEM

EC-343

Revision: 2004 November

2004 Murano

20.

CHECK EVAP/ORVR LINE

Check EVAP/ORVR line between EVAP canister and fuel tank for clogging, kink, looseness and improper con-
nection. For location, refer to

EC-658, "ON BOARD REFUELING VAPOR RECOVERY (ORVR)"

OK or NG

>> GO TO 21.

>> Repair or replace hoses and tubes.

21.

CHECK RECIRCULATION LINE

Check recirculation line between filler neck tube and fuel tank for clogging, kink, cracks, looseness and
improper connection.

OK or NG

>> GO TO 22.

>> Repair or replace hose, tube or filler neck tube.

22.

CHECK REFUELING EVAP VAPOR CUT VALVE

Refer to

EC-661, "Component Inspection"

OK or NG

>> GO TO 23.

>> Replace refueling EVAP vapor cut valve with fuel tank.

23.

CHECK FUEL LEVEL SENSOR

Refer to

DI-28, "FUEL LEVEL SENSOR UNIT CHECK"

OK or NG

>> GO TO 24.

>> Replace fuel level sensor unit.

24.

CHECK INTERMITTENT INCIDENT

Refer to

EC-130, "TROUBLE DIAGNOSIS FOR INTERMITTENT INCIDENT"

>> INSPECTION END

EC-344

DTC P0460 FUEL LEVEL SENSOR

Revision: 2004 November

2004 Murano

DTC P0460 FUEL LEVEL SENSOR

PFP:25060

Component Description

ABS004HP

The fuel level sensor is mounted in the fuel level sensor unit. The
sensor detects a fuel level in the fuel tank and transmits a signal to
the “unified meter and A/C amp.”. The “unified meter and A/C amp.”
sends the fuel level sensor signal to the ECM through CAN commu-
nication line.
It consists of two parts, one is mechanical float and the other is vari-
able resistor. Fuel level sensor output voltage changes depending on
the movement of the fuel mechanical float.

On Board Diagnosis Logic

ABS004HQ

NOTE:
If DTC P0460 is displayed with DTC U1000 or U1001, first perform the trouble diagnosis for DTC U1000,
U1001. Refer to

EC-140

When the vehicle is parked, naturally the fuel level in the fuel tank is stable. It means that output signal of the
fuel level sensor does not change. If ECM senses sloshing signal from the sensor, fuel level sensor malfunc-
tion is detected.

DTC Confirmation Procedure

ABS004HR

NOTE:
If DTC Confirmation Procedure has been previously conducted, always turn ignition switch OFF and wait at
least 10 seconds before conducting the next test.

WITH CONSULT-II

Turn ignition switch ON.

Select “DATA MONITOR” mode with CONSULT-II.

Start engine and wait maximum of 2 consecutive minutes.

If 1st trip DTC is detected, go to

EC-345, "Diagnostic Procedure"

WITH GST

Follow the procedure “WITH CONSULT-II” above.

PBIB1356E

DTC No.

Trouble diagnosis name

DTC detecting condition

Possible cause

P0460
0460

Fuel level sensor circuit
noise

Even though the vehicle is parked, a signal
being varied is sent from the fuel level sensor
to ECM.

●

Harness or connectors
(The CAN communication line is open or
shorted)

●

Harness or connectors
(The sensor circuit is open or shorted)

●

Unified meter and A/C amp.

●

Fuel level sensor

SEF195Y

DTC P0460 FUEL LEVEL SENSOR

EC-345

Revision: 2004 November

2004 Murano

Diagnostic Procedure

ABS004HS

CHECK DTC WITH UNIFIED METER AND A/C AMP.

Refer to

DI-36, "SELF-DIAGNOSTIC RESULTS"

OK or NG

>> GO TO 2.

>> Go to

DI-22, "Fuel Level Sensor Signal Inspection 1"

CHECK INTERMITTENT INCIDENT

Refer to

EC-130, "TROUBLE DIAGNOSIS FOR INTERMITTENT INCIDENT"

>> INSPECTION END

Removal and Installation

ABS004HT

FUEL LEVEL SENSOR

Refer to

FL-4, "FUEL LEVEL SENSOR UNIT, FUEL FILTER AND FUEL PUMP ASSEMBLY"

EC-346

DTC P0461 FUEL LEVEL SENSOR

Revision: 2004 November

2004 Murano

DTC P0461 FUEL LEVEL SENSOR

PFP:25060

Component Description

ABS004HU

On Board Diagnosis Logic

ABS004HV

NOTE:
If DTC P0461 is displayed with DTC U1000 or U1001, first perform the trouble diagnosis for DTC U1000,
U1001. Refer to

EC-140

Driving long distances naturally affect fuel gauge level.
This diagnosis detects the fuel gauge malfunction of the gauge not moving even after a long distance has
been driven.

Overall Function Check

ABS004HW

Use this procedure to check the overall function of the fuel level sensor function. During this check, a 1st trip
DTC might not be confirmed.

WARNING:

When performing following procedure, be sure to observe the handling of the fuel. Refer to

FL-9,

"FUEL TANK"

TESTING CONDITION:
Before starting overall function check, preparation of draining fuel and refilling fuel is required.

WITH CONSULT-II

NOTE:
Start from step 10, if it is possible to confirm that the fuel cannot be drained by 30 (7-7/8 US gal, 6-5/
8 Imp gal) in advance.

Prepare a fuel container and a spare hose.

Release fuel pressure from fuel line, refer to

EC-45, "FUEL PRESSURE RELEASE"

Remove the fuel feed hose on the fuel level sensor unit.

Connect a spare fuel hose where the fuel feed hose was removed.

Turn ignition switch OFF and wait at least 10 seconds then turn ON.

Select “FUEL LEVEL SE” in “DATA MONITOR” mode with CONSULT-II.

PBIB1356E

DTC No.

Trouble diagnosis name

DTC detecting condition

Possible cause

P0461
0461

Fuel level sensor circuit
range/performance

The output signal of the fuel level sensor does
not change within the specified range even
though the vehicle has been driven a long dis-
tance.

●

Harness or connectors
(The CAN communication line is open or
shorted)

●

Harness or connectors
(The sensor circuit is open or shorted)

●

Unified meter and A/C amp.

●

Fuel level sensor

DTC P0461 FUEL LEVEL SENSOR

EC-347

Revision: 2004 November

2004 Murano

Check “FUEL LEVEL SE” output voltage and note it.

Select “FUEL PUMP” in “ACTIVE TEST” mode with CONSULT-
II.

Touch ON and drain fuel approximately 30 (7-7/8 US gal, 6-5/
8 Imp gal) and stop it.

10. Check “FUEL LEVEL SE” output voltage and note it.

11. Fill fuel into the fuel tank for 30 (7-7/8 US gal, 6-5/8 Imp gal).

12. Check “FUEL LEVEL SE” output voltage and note it.

13. Confirm whether the voltage changes more than 0.03V during

step 7 to 10 and 10 to 12.
If NG, go to

EC-347, "Diagnostic Procedure"

WITH GST

NOTE:
Start from step 8, if it is possible to confirm that the fuel cannot be drained by 30 (7-7/8 US gal, 6-5/8
Imp gal) in advance.

Prepare a fuel container and a spare hose.

Release fuel pressure from fuel line. Refer to

EC-45, "FUEL PRESSURE RELEASE"

Remove the fuel feed hose on the fuel level sensor unit.

Connect a spare fuel hose where the fuel feed hose was removed.

Turn ignition switch ON.

Drain fuel by 30 (7-7/8 US gal, 6-5/8 Imp gal) from the fuel tank using proper equipment.

Confirm that the fuel gauge indication varies.

Fill fuel into the fuel tank for 30 (7-7/8 US gal, 6-5/8 Imp gal).

Confirm that the fuel gauge indication varies.

10. If NG, go to

EC-347, "Diagnostic Procedure"

Diagnostic Procedure

ABS004HX

CHECK DTC WITH UNIFIED METER AND A/C AMP.

Refer to

DI-36, "SELF-DIAGNOSTIC RESULTS"

OK or NG

>> GO TO 2.

>> Go to

DI-22, "Fuel Level Sensor Signal Inspection 1"

CHECK INTERMITTENT INCIDENT

Refer to

EC-130, "TROUBLE DIAGNOSIS FOR INTERMITTENT INCIDENT"

>> INSPECTION END

Removal and Installation

ABS004HY

FUEL LEVEL SENSOR

Refer to

FL-4, "FUEL LEVEL SENSOR UNIT, FUEL FILTER AND FUEL PUMP ASSEMBLY"

SEF195Y

EC-348

DTC P0462, P0463 FUEL LEVEL SENSOR

Revision: 2004 November

2004 Murano

DTC P0462, P0463 FUEL LEVEL SENSOR

PFP:25060

Component Description

ABS004HZ

On Board Diagnosis Logic

ABS004VI

NOTE:
If DTC P0462 or P0463 is displayed with DTC U1000 or U1001, first perform the trouble diagnosis for
DTC U1000, U1001. Refer to

EC-140

This diagnosis indicates the former, to detect open or short circuit malfunction.

DTC Confirmation Procedure

ABS004I1

NOTE:
If DTC Confirmation Procedure has been previously conducted, always turn ignition switch OFF and wait at
least 10 seconds before conducting the next test.
TESTING CONDITION:
Before performing the following procedure, confirm that battery voltage is more than 11V at ignition
switch ON.

WITH CONSULT-II

Turn ignition switch ON.

Select “DATA MONITOR” mode with CONSULT-II.

Wait at least 5 seconds.

If 1st trip DTC is detected, go to

EC-349, "Diagnostic Procedure"

WITH GST

Follow the procedure “WITH CONSULT-II” above.

PBIB1356E

DTC No.

Trouble diagnosis name

DTC detecting condition

Possible cause

P0462
0462

Fuel level sensor circuit
low input

An excessively low voltage from the sensor is
sent to ECM.

●

Harness or connectors
(The CAN communication line is open or
shorted)

●

Harness or connectors
(The sensor circuit is open or shorted)

●

Unified meter and A/C amp.

●

Fuel level sensor

P0463
0463

Fuel level sensor circuit
high input

An excessively high voltage from the sensor is
sent to ECM.

SEF195Y

DTC P0462, P0463 FUEL LEVEL SENSOR

EC-349

Revision: 2004 November

2004 Murano

Diagnostic Procedure

ABS004I2

CHECK DTC WITH UNIFIED METER AND A/C AMP.

Refer to

DI-36, "SELF-DIAGNOSTIC RESULTS"

OK or NG

>> GO TO 2.

>> Go to

DI-22, "Fuel Level Sensor Signal Inspection 1"

CHECK INTERMITTENT INCIDENT

Refer to

EC-130, "TROUBLE DIAGNOSIS FOR INTERMITTENT INCIDENT"

>> INSPECTION END

Removal and Installation

ABS004I3

FUEL LEVEL SENSOR

Refer to

FL-4, "FUEL LEVEL SENSOR UNIT, FUEL FILTER AND FUEL PUMP ASSEMBLY"

EC-350

DTC P0500 VSS

Revision: 2004 November

2004 Murano

DTC P0500 VSS

PFP:32702

Description

ABS004I4

NOTE:
If DTC P0500 is displayed with DTC U1000 or U1001, first perform the trouble diagnosis for DTC U1000,
U1001. Refer to

EC-140, "DTC U1000, U1001 CAN COMMUNICATION LINE"

The vehicle speed signal is sent to the “unified meter and A/C amp.” from the “ABS actuator and electric unit
(control unit)” by CAN communication line. The “unified meter and A/C amp.” then sends a signal to the ECM
by CAN communication line.

On Board Diagnosis Logic

ABS004I5

DTC Confirmation Procedure

ABS004I6

CAUTION:

Always drive vehicle at a safe speed.

NOTE:
If DTC Confirmation Procedure has been previously conducted, always turn ignition switch OFF and wait at
least 10 seconds before conducting the next test.
TESTING CONDITION:
Steps 1 and 2 may be conducted with the drive wheels lifted in the shop or by driving the vehicle. If a
road test is expected to be easier, it is unnecessary to lift the vehicle.

WITH CONSULT-II

Start engine (VDC switch OFF).

Read “VHCL SPEED SE” in “DATA MONITOR” mode with CONSULT-II. The vehicle speed on CONSULT-
II should exceed 10 km/h (6 MPH) when rotating wheels with suitable gear position.
If NG, go to

EC-351, "Diagnostic Procedure"

If OK, go to following step.

Select “DATA MONITOR” mode with CONSULT-II.

Warm engine up to normal operating temperature.

Maintain the following conditions for at least 60 consecutive sec-
onds.

If 1st trip DTC is detected, go to

EC-351, "Diagnostic Procedure"

Overall Function Check

ABS004I7

Use this procedure to check the overall function of the vehicle speed sensor circuit. During this check, a 1st
trip DTC might not be confirmed.

DTC No.

Trouble diagnosis name

DTC detecting condition

Possible cause

P0500
0500

Vehicle speed sensor

The almost 0 km/h (0 MPH) signal from
vehicle speed sensor is sent to ECM
even when vehicle is being driven.

●

Harness or connectors
(The CAN communication line is open or
shorted)

●

Harness or connectors
(The vehicle speed signal circuit is open or
shorted)

●

Wheel sensor

●

Unified meter and A/C amp.

●

ABS actuator and electric unit (control unit)

ENG SPEED

1,600 - 6,000 rpm

COOLAN TEMP/S

More than 70

C (158

B/FUEL SCHDL

5.5 - 31.8 msec

Selector lever

Except P or N position

PW/ST SIGNAL

OFF

SEF196Y

Content .. 87 88 89 90 ..