Nissan Murano Z50 (2004 year). Manual - part 67

 

  Index      Manuals     Nissan Murano Z50 (2004 year) - Service and Repair Manual

 

Search            copyright infringement  

 

 

 

 

 

 

 

 

Content      ..     65      66      67      68     ..

 

 

Nissan Murano Z50 (2004 year). Manual - part 67

 

 

CVT INDICATOR

DI-59

C

D

E

F

G

H

I

J

L

M

A

B

DI

Revision: 2004 November

2004 Murano

4. 

CHECK UNIFIED METER AND A/C AMP. INPUT SIGNAL

1.

Lift up drive wheels.

2.

Connect CONSULT-II and start engine. 

3.

Use “DATA MONITOR” of “METER A/C AMP” on CONSULT-II.
Confirm each indication on the monitor when operating the shift
lever.

OK or NG

OK

>> Replace combination meter.

NG

>> GO TO 5.

5. 

CHECK CVT DEVICE

Check the following.

CVT device (Manual mode switch) inspection. Refer to 

CVT-132, "DTC P0826 MANUAL MODE SWITCH

CIRCUIT"

  in CVT section. [With manual mode]

CVT device (Second position switch). Refer to 

CVT-178, "SECOND POSITION SWITCH"

  in CVT section.

 [Without manual mode]

OK or NG

OK

>> GO TO 6.

NG

>> Repair corresponding parts.

6. 

CHECK TCM

Check TCM input/output signal. Refer to 

CVT-56, "TCM Input/Output Signal Reference Values"

  in CVT sec-

tion.

OK or NG

OK

>> Replace the unified meter and A/C amp. Refer to 

DI-38, "Removal and Installation of Unified

Meter and A/C Amp."

 .

NG

>> Check corresponding parts.

CONSULT-II display

Switch operation

Operation 

status

AT-M IND

OFF

AT-M GEAR

1

P RANGE IND

P range position

ON

Except for P range position

OFF

R RANGE IND

R range position

ON

Except for R range position

OFF

N RANGE IND

N range position

ON

Except for N range position

OFF

D RANGE IND

D range position

ON

Except for D range position

OFF

L RANGE IND

L range position

ON

Except for L range position

OFF

S RANGE IND

S range position

ON

Except for S range position

OFF

PKIA2499E

DI-60

WARNING CHIME

Revision: 2004 November

2004 Murano

WARNING CHIME

PFP:24814

Component Parts and Harness Connector Location

AKS004GY

System Description

AKS004GZ

FUNCTION

Power is supplied at all times

through 50A fusible link (letter F , located in the fuse and fusible link box)

to BCM terminal 55

through 10A fuse [No. 18, located in the fuse block (J/B)]

to BCM terminal 42

through 10A fuse [No. 21, located in the fuse block (J/B)] 

to key switch and key lock solenoid terminal 3, and

to combination meter terminal 21

through 10A fuse [No. 19, located in the fuse block (J/B)] 

to unified meter and A/C amp. terminal 21.

When ignition switch ON or START position, power is supplied

through 10A fuse [No. 1, located in the fuse block (J/B)]

to BCM terminal 38

through 10A fuse [No. 12, located in the fuse block (J/B)]

to unified meter and A/C amp. terminal 22

Ground is supplied

to BCM terminals 49 and 52

through body grounds M14 and M78

to unified meter and A/C amp. terminals 29 and 30

through body grounds M14 and M78

to combination meter terminals 22, 23 and 24

SKIA8975E

WARNING CHIME

DI-61

C

D

E

F

G

H

I

J

L

M

A

B

DI

Revision: 2004 November

2004 Murano

through body grounds M14 and M78.

NOTE:
When ignition key warning chime, light warning chime, and seat belt warning chime should be conducted at
the same time, the priorities for each chime are the following.
1.

Light warning chime

2.

Ignition key warning chime

3.

Seat belt warning chime

IGNITION KEY WARNING CHIME

With the key inserted into the ignition switch, and the driver's door open, the warning chime will sound.
Power is supplied

through key switch and key lock solenoid terminal 4

to BCM terminal 37.

Ground is supplied

through BCM terminal 62

to driver side door switch terminal 4. 

Driver side door switch terminal 5 is grounded through body grounds M14 and M78.
Unified meter and A/C amp. send door open signal to BCM with CAN communication line.
BCM detects key inserted into the ignition switch, and sends key warning signal to unified meter and A/C amp.
with CAN communication line. Unified meter and A/C amp. sends key warning signal to combination meter
with communication line between unified meter and A/C amp. and combination meter.
When combination meter receives key warning signal, it sounds warning chime.

LIGHT WARNING CHIME

With the key removed from the ignition switch, the driver's door open, and the lighting switch in 1st or 2nd posi-
tion, the warning chime will sound. [Except when headlamp battery saver control operates (for 5 minutes after
ignition switch is turned to OFF or ACC position) and headlamps do not illuminate.]
Signal is supplied

from combination switch (lighting switch) terminals 1, 2, 3, 4, 5, 6, 7, 8, 9 and 10

to BCM terminals 2, 3, 4, 5, 6, 32, 33, 34, 35 and 36.

NOTE:
BCM detected lighting switch in 1st or 2nd position, refer to 

BCS-3, "COMBINATION SWITCH READING

FUNCTION"

 .

Ground is supplied

through BCM terminal 62

to driver side door switch terminal 4. 

Driver side door switch terminal 5 is grounded through body grounds M14 and M78.
Unified meter and A/C amp. send door open signal to BCM with CAN communication line.
BCM detects headlamps are illuminated, and sends light warning signal to unified meter and A/C amp. with
CAN communication line. Unified meter and A/C amp. sends light warning signal to combination meter with
communication line between unified meter and A/C amp. and combination meter.
When combination meter receives light warning signal, it sounds warning chime.

SEAT BELT WARNING CHIME

With ignition switch turned ON and seat belt unfastened [seat belt buckle switch (driver side) ON], warning
chime will sound for approximately 6 seconds.
Ground is supplied

to combination meter terminal 3

through seat belt buckle switch (driver side) terminal 50.

Seat belt buckle switch (driver side) terminal 65 is grounded through body grounds B7 and B20.
Combination meter sends seat belt unfastened [seat belt buckle switch (driver side) ON] signal to unified
meter and A/C amp. with communication line between unified meter and A/C amp. and combination meter. 
BCM receives seat belt unfastened [seat belt buckle switch (driver side) ON] signal from unified meter and A/
C amp. with CAN communication line, and sends seat belt warning signal to unified meter and A/C amp. with
CAN communication line. Unified meter and A/C amp. sends seat belt warning signal to combination meter
with communication line between unified meter and A/C amp. and combination meter.

DI-62

WARNING CHIME

Revision: 2004 November

2004 Murano

When combination meter receives seat belt warning signal, it sounds warning chime.

CAN Communication System Description

AKS004H0

CAN (Controller Area Network) is a serial communication line for real time application. It is an on-vehicle mul-
tiplex communication line with high data communication speed and excellent error detection ability. Many elec-
tronic control units are equipped onto a vehicle, and each control unit shares information and links with other
control units during operation (not independent). In CAN communication, control units are connected with 2
communication lines (CAN H line, CAN L line) allowing a high rate of information transmission with less wiring.
Each control unit transmits/receives data but selectively reads required data only.

CAN Communication Unit

AKS007PP

Refer to 

LAN-8, "CAN Communication Unit"

  in “LAN SYSTEM”.

WARNING CHIME

DI-63

C

D

E

F

G

H

I

J

L

M

A

B

DI

Revision: 2004 November

2004 Murano

Wiring Diagram — CHIME —

AKS004H3

TKWA1712E

DI-64

WARNING CHIME

Revision: 2004 November

2004 Murano

TKWA1713E

WARNING CHIME

DI-65

C

D

E

F

G

H

I

J

L

M

A

B

DI

Revision: 2004 November

2004 Murano

Terminals and Reference Value for BCM

AKS004H4

Terminal 

No.

Wire 

color

Signal name

Measuring condition

Reference value (V)

Ignition 

switch

Operation or condition

2

R

Combination switch input 5

ON

Lighting, turn, wiper OFF
Wiper dial position 4

3

P/L

Combination switch input 4

ON

Lighting, turn, wiper OFF
Wiper dial position 4

4

R/G

Combination switch input 3

ON

Lighting, turn, wiper OFF
Wiper dial position 4

5

R/B

Combination switch input 2

ON

Lighting, turn, wiper OFF
Wiper dial position 4

6

R/W

Combination switch input 1

32

LG/B

Combination switch output 5

ON

Lighting, turn, wiper OFF
Wiper dial position 4

33

G/Y

Combination switch output 4

ON

Lighting, turn, wiper OFF
Wiper dial position 4

34

LG/R

Combination switch output 3

ON

Lighting, turn, wiper OFF
Wiper dial position 4

SKIA5291E

SKIA5292E

SKIA5291E

SKIA5292E

SKIA5291E

SKIA5292E

SKIA5291E

DI-66

WARNING CHIME

Revision: 2004 November

2004 Murano

Terminals and Reference Value for Unified Meter and A/C Amp. 

AKS004H5

35

G/B

Combination switch output 2

ON

Lighting, turn, wiper OFF
Wiper dial position 4

36

L/W

Combination switch output 1

37

B/R

Key switch signal

OFF

Key is removed.

Approx. 0

Key is inserted.

Approx. 12

38

R

Ignition switch ON or START 

ON

Battery voltage

39

L

CAN H

40

Y

CAN L

42

GR

Battery power supply

OFF

Battery voltage

49

B

Ground (Signal)

ON

Approx. 0

52

B

Ground (Power)

55

W/B

Battery power supply (F/L)

OFF

Battery voltage

62

SB

Driver side door switch signal

OFF

ON (open)

Approx. 0

OFF (closed)

Approx. 12

Terminal 

No.

Wire 

color

Signal name

Measuring condition

Reference value (V)

Ignition 

switch

Operation or condition

SKIA5292E

Terminal 

No.

Wire 

color

Item

Measuring or condition

Reference value (V)

Ignition 

switch

Operation or condition

1

L

CAN H

OFF

9

R/B

TX communication line (To 
combination meter)

ON

11

Y

CAN L

OFF

19

R/L

RX communication line 
(From combination meter)

ON

21

Y/R

Battery power supply

OFF

Battery voltage

22

G

Ignition switch ON or START

ON

Battery voltage

29

B

Ground (power)

ON

Approx. 0

30

B

Ground

ON

Approx. 0

SKIA3362E

SKIA3361E

WARNING CHIME

DI-67

C

D

E

F

G

H

I

J

L

M

A

B

DI

Revision: 2004 November

2004 Murano

Terminals and Reference Value for Combination Meter

AKS004H6

How to Proceed With Trouble Diagnosis

AKS004H7

1.

Confirm the symptom or customer complaint.

2.

Understand operation description and function description. Refer to 

DI-60, "System Description"

 .

3.

Perform the preliminary check. Refer to 

DI-68, "Preliminary Check"

 .

4.

Start engine.

5.

Select “METER A/C AMP” on CONSULT-II, and perform self-diagnosis of unified meter and A/C amp.
Refer to 

DI-35, "CONSULT-II Function"

 .

6.

After erasing the self-diagnosis result, perform self-diagnosis again. When no malfunction detected, go to
next step 7. When malfunction detected, go to 

DI-18, "Symptom Chart 2"

  in “COMBINATION METER”.

7.

Check symptom and repair or replace the cause of malfunction.

8.

Does the warning chime operate normally? If so, go to 9. If not, go to 7.

9.

INSPECTION END

Terminal 

No.

Wire 

color

Item

 Measuring condition

Reference value (V)

Ignition 

switch

Operation or condition

3

LG

Seat belt buckle switch 
(Driver side) 

ON

Unfastened (ON)

Approx. 0

Fastened (OFF)

Approx. 12

18

R/L

TX communication line (To 
unified meter and A/C amp.)

ON

19

R/B

RX communication line 
(From unified meter and A/C 
amp.)

ON

20

O

Ignition switch ON or START

ON

Battery voltage

21

Y/R

Battery power supply

OFF

Battery voltage

22

B

Ground

ON

Approx. 0

23

24

SKIA3361E

SKIA3362E

DI-68

WARNING CHIME

Revision: 2004 November

2004 Murano

Preliminary Check

AKS004H8

INSPECTION FOR POWER SUPPLY AND GROUND CIRCUIT

1. 

CHECK FUSE AND FUSIBLE LINK

Check for blown BCM fuses.

OK or NG

OK

>> GO TO 2.

NG

>> If fuse is blown, be sure to eliminate cause of malfunction before installing new fuse. Refer to 

PG-

3, "POWER SUPPLY ROUTING CIRCUIT"

 .

2. 

CHECK POWER SUPPLY CIRCUIT

1.

Disconnect BCM connector.

2.

Check voltage between BCM harness connector terminals and
ground.

OK or NG

OK

>> GO TO 3.

NG

>> Check harness for open between BCM and fuse.

3. 

CHECK GROUND CIRCUIT

1.

Turn ignition switch OFF. 

2.

Check continuity between BCM harness connector M35 termi-
nals 49 (B), 52 (B) and ground.

OK or NG

OK

>> INSPECTION END

NG

>> Repair harness or connector.

Unit

Power source

Fuse and fusible link No.

BCM

Battery

F

18

Ignition switch ON or START

1

Terminals

Ignition switch position

(+)

(–)

OFF

ON

Connector

Terminal 

(Wire color)

M35

55 (W/B)

Ground

Battery voltage

Battery voltage

42 (GR)

M34

38 (R)

0V

Battery voltage

SKIA8976E

Continuity should exist.

SKIA5041E

WARNING CHIME

DI-69

C

D

E

F

G

H

I

J

L

M

A

B

DI

Revision: 2004 November

2004 Murano

CONSULT-II Function

AKS00ASB

CONSULT-II performs the following functions communicating with the BCM.

DIAGNOSTIC ITEMS DESCRIPTION

CONSULT-II BASIC OPERATION PROCEDURE

CAUTION:

If CONSULT-II is used with no connection of CONSULT-II CONVERTER, malfunctions might be
detected in self-diagnosis depending on control unit which carry out CAN communication.

1.

With the ignition switch OFF, connect “CONSULT-II” and “CON-
SULT-II CONVERTER” to the data link connector, and turn the
ignition switch ON.

2.

Touch “START (NISSAN BASED VHCL)”.

3.

Touch “BCM” on “SELECT SYSTEM” screen. If “BCM” is not
indicated, go to 

GI-39, "CONSULT-II Data Link Connector (DLC)

Circuit"

 .

BCM diagnosis position

Diagnosis mode

Description

BUZZER

Data monitor

The input data to the BCM control unit is displayed in real time.

Active test

Operation of electrical loads can be checked by sending driving signal to them.

BCM

Self-diagnostic

BCM performs self-diagnosis of CAN communication.

PBIB1300E

SKIA3098E

SKIA8977E

DI-70

WARNING CHIME

Revision: 2004 November

2004 Murano

4.

Touch “BUZZER” or “BCM”.

5.

Select “DATA MONITOR”, “ACTIVE TEST” or “SELF-DIAG
RESULTS”.

DATA MONITOR
Operation Procedure

1.

Touch “BUZZER” on “SELECT TEST ITEM” screen.

2.

Touch “DATA MONITOR” on “SELECT DIAG MODE” screen.

3.

Touch “ALL SIGNALS” or “SELECTION FROM MENU” on “DATA MONITOR” screen.

4.

If “SELECTION FROM MENU” is selected, touch the desired monitor item. If “ALL SIGNALS” is selected,
all items required to control are monitored.

5.

Touch “START”.

6.

During monitoring, touching “RECORD” can start recording the monitored item status.

Data Monitor Item

ACTIVE TEST
Operation Procedure

1.

Touch “BUZZER” on “SELECT TEST ITEM” screen.

2.

Touch “ACTIVE TEST” on “SELECT DIAG MODE” screen.

3.

Touch the item to be tested, and check the operation.

4.

During the operation check, touching “OFF” deactivates the operation.

Active Test Item

SELF-DIAGNOSTIC RESULTS
Operation Procedure

1.

Touch “BCM” on “SELECT TEST ITEM” screen.

2.

Touch “SELF-DIAG RESULTS” on “SELECT DIAG MODE” screen.

SKIA5788E

ALL SIGNALS

Monitors main items.

SELECTION FROM MENU

Selects and monitors items.

Monitored item

ALL SIGNALS

SELECTION 

FROM MENU

Contents

IGN ON SW

X

X

Indicates [ON/OFF] condition of ignition switch.

KEY ON SW

X

X

Indicates [ON/OFF] condition of key switch.

DOOR SW-DR

X

X

Indicates [ON/OFF] condition of front door switch (driver side).

TAIL LAMP SW

X

X

Indicates [ON/OFF] condition of lighting switch.

BUCKLE SW

X

X

Indicates [ON/OFF] condition of seat belt buckle switch (driver side).

Test item

Malfunction is detected when···

LIGHT WARN ALM

This test is able to check light warning chime operation. Light warning chime sounds for 2 seconds 
after touching “ON” on CONSULT-ll screen.

IGN KEY WARN ALM

This test is able to check key warning chime operation. Key warning chime sounds for 2 seconds 
after touching “ON” on CONSULT-ll screen.

SEAT BELT WARN TEST

This test is able to check seat belt warning chime operation. Seat belt warning chime sounds for 2 
seconds after touching “ON” on CONSULT-ll screen.

WARNING CHIME

DI-71

C

D

E

F

G

H

I

J

L

M

A

B

DI

Revision: 2004 November

2004 Murano

3.

Self-diagnostic results are displayed.

Display Item List

NOTE:
If “CAN communication [U1000]” is indicated, after printing the monitor item, go to “CAN system”. Refer to

LAN-6, "Precautions When Using CONSULT-II"

 .

All Warnings Are Not Operated

AKS004HA

1. 

CHECK CHIME OPERATION

1.

Select “BCM” on CONSULT-II.

2.

Select “BUZZER” on CONSULT-II, and perform “KEY WARN
ALM”, “LIGHT WARN ALM” or “SEAT BELT ALM” of “ACTIVE
TEST”.

Does chime sound?

YES

>> Replace BCM. Refer to 

BCS-14, "Removal and Installa-

tion of BCM"

 .

NO

>> GO TO 2.

2. 

CHECK UNIFIED METER AND A/C AMP. INPUT SIGNAL

1.

Select “METER A/C AMP” on CONSULT-II.

2.

Operate switches meet the requirements to sounds warning
chime with “BUZZER” of “DATA MONITOR” and check operation
status. 

OK or NG

OK

>> Replace combination meter.

NG

>> Replace BCM. Refer to 

BCS-14, "Removal and Installa-

tion of BCM"

 .

Key Warning Chime and Light Warning Chime Does Not Operate (Seat belt 
Warning Chime Does Operate)

AKS005GZ

1. 

CHECK BCM INPUT SIGNAL

1.

Select “BCM” on CONSULT-II.

2.

With “DATA MONITOR” of “BUZZER”, confirm “DOOR SW-DR”
when the driver side door is operated.

OK or NG

OK

>> Replace BCM. Refer to 

BCS-14, "Removal and Installa-

tion of BCM"

 .

NG

>> GO TO 2.

Monitored Item

CONSULT-ll display

Description

CAN communication

CAN communication [U1000]

Malfunction is detected in CAN communication.

SKIA6331E

When meet the requirements to 
sounds warning chime

: BUZZER ON

Except above

: BUZZER OFF

PKIA2063E

When driver side door 
is opened

: DOOR SW-DR ON

When driver side door 
is closed

: DOOR SW-DR OFF

SKIA2003E

DI-72

WARNING CHIME

Revision: 2004 November

2004 Murano

2. 

CHECK DRIVER SIDE DOOR SWITCH CIRCUIT

1.

Turn ignition switch OFF.

2.

Disconnect BCM connector and driver side door switch connector.

3.

Check continuity between BCM harness connector M36 terminal
62 (SB) and driver side door switch harness connector D10 ter-
minal 4 (SB).

4.

Check continuity between BCM harness connector M36 terminal
62 (SB) and ground.

OK or NG

OK

>> GO TO 3.

NG

>> Repair harness or connector.

3. 

CHECK DRIVER SIDE DOOR SWITCH

Check continuity between driver side door switch connector termi-
nals 4 and 5 while turning the door switch.

OK or NG

OK

>> GO TO 5.

NG

>> Replace driver side door switch.

4. 

CHECK DRIVER SIDE DOOR SWITCH GROUND CIRCUIT

Check continuity between driver side door switch harness connector
D10 terminal 5 (B) and ground.

OK or NG

OK

>> Replace BCM. Refer to 

BCS-14, "Removal and Installa-

tion of BCM"

 .

NG

>> Repair harness.

Key Warning Chime Does Not Operate

AKS004HB

1. 

CHECK FUSE

Check if the key switch fuse and key lock solenoid 10A fuse [No. 21, located in the fuse block (J/B)] is blown.
Refer to 

DI-63, "Wiring Diagram — CHIME —"

 .

Is the fuse blown?

YES

>> Replace fuse. Be sure to repair the cause of malfunction before installing new fuse.

NO

>> GO TO 2.

Continuity should exist.

Continuity should not exist.

SKIB0059E

When driver side door 
is opened

: Continuity should exist.

When driver side door 
is closed

: Continuity should not exist.

PKIA2502E

Continuity should exist.

PKIA2576E

WARNING CHIME

DI-73

C

D

E

F

G

H

I

J

L

M

A

B

DI

Revision: 2004 November

2004 Murano

2. 

CHECK WARNING CHIME OPERATION

Check the chime under conditions in exception of key warning chime operation.

Does warning chime sound?

YES

>> GO TO 3.

NO

>> Go to 

DI-71, "All Warnings Are Not Operated"

  or 

DI-71, "Key Warning Chime and Light Warning

Chime Does Not Operate (Seat belt Warning Chime Does Operate)"

 .

3. 

CHECK BCM INPUT SIGNAL

With CONSULT-ll

1.

Select “BCM”.

2.

With “DATA MONITOR” of “BUZZER”, confirm “KEY ON SW”
when the key is operated.

Without CONSULT-ll

Check voltage between BCM harness connector M34 terminal 37 (B/
R) and ground.

OK or NG

OK

>> Replace BCM. Refer to 

BCS-14, "Removal and Installa-

tion of BCM"

 .

NG

>> GO TO 4.

4. 

CHECK KEY SWITCH

1.

Disconnect key switch and key lock solenoid connector.

2.

Check continuity between key switch and key lock solenoid con-
nector M28 terminals 3 and 4.

OK or NG

OK

>> GO TO 5.

NG

>> Replace key switch and key lock solenoid.

When key is inserted to ignition 
key cylinder

: KEY ON SW ON

When key is removed from 
ignition key cylinder

: KEY ON SW OFF

SKIA1960E

When key is inserted to ignition 
key cylinder

: Approx. 12V

When key is removed from 
ignition key cylinder

: Approx. 0V

SKIA5048E

When key is inserted to 
ignition key cylinder

: Continuity should exist.

When key is removed 
from ignition key cylinder

: Continuity should not 
exist.

PKIA2503E

DI-74

WARNING CHIME

Revision: 2004 November

2004 Murano

5. 

CHECK KEY SWITCH CIRCUIT 

1.

Disconnect BCM connector.

2.

Check continuity between BCM harness connector M34 terminal
37 (B/R) and key switch and key lock solenoid harness connec-
tor M28 terminal 4 (B/R).

3.

Check continuity between BCM harness connector M34 terminal
37 (B/R) and ground.

OK or NG

OK

>> GO TO 6.

NG

>> Repair harness or connector.

6. 

CHECK KEY SWITCH POWER SUPPLY CIRCUIT

Check voltage between key switch and key lock solenoid harness
connector M28 terminal 3 (Y/R) and ground.

OK or NG

OK

>> Replace BCM. Refer to 

BCS-14, "Removal and Installa-

tion of BCM"

 .

NG

>> Check harness for open or short between key switch

and key lock solenoid and fuse.

Light Warning Chime Does Not Operate

AKS007OI

1. 

CHECK WARNING CHIME OPERATION

Check the chime under conditions in exception of light warning chime operation.
Does warning chime sound?

YES

>> GO TO 2.

NO

>> Go to 

DI-71, "All Warnings Are Not Operated"

 .

2. 

CHECK BCM INPUT SIGNAL

1.

Select “BCM” on CONSULT-II.

2.

With “DATA MONITOR” of “BUZZER”, confirm “TAIL LAMP SW”
when the lighting switch is operated.

OK or NG

OK

>> Replace BCM. Refer to 

BCS-14, "Removal and Installa-

tion of BCM"

 .

NG

>> Replace lighting switch.

Continuity should exist.

Continuity should not exist.

SKIA8756E

Battery voltage should exist.

PKIA2505E

When lighting switch is in 
1st position

: TAIL LAMP SW ON

When lighting switch is OFF

: TAIL LAMP SW OFF

SKIA2081E

 

 

 

 

 

 

 

Content      ..     65      66      67      68     ..