Nissan Murano Z50 (2003 year). Manual - part 184

 

  Index      Manuals     Nissan Murano Z50 (2003 year) - Service and Repair Manual

 

Search            copyright infringement  

 

 

 

 

 

 

 

 

Content      ..     182      183      184      185     ..

 

 

Nissan Murano Z50 (2003 year). Manual - part 184

 

 

LAN-558

[CAN]

CAN SYSTEM (TYPE 16)

Revision; 2004 April

2003 Murano

2. 

CHECK HARNESS FOR OPEN CIRCUIT

1.

Disconnect ABS actuator and electric unit (control unit) connector.

2.

Check resistance between ABS actuator and electric unit (con-
trol unit) harness connector E24 terminals 11 (L) and 15 (Y).

OK or NG

OK

>> Replace ABS actuator and electric unit (control unit).

NG

>> Repair harness between ABS actuator and electric unit

(control unit) and IPDM E/R.

IPDM E/R Circuit Check

AKS006XK

1. 

CHECK CONNECTOR

1.

Turn ignition switch OFF.

2.

Disconnect the negative battery terminal.

3.

Check terminals and connector of IPDM E/R for damage, bend and loose connection (control module side
and harness side).

OK or NG

OK

>> GO TO 2.

NG

>> Repair terminal or connector.

2. 

CHECK HARNESS FOR OPEN CIRCUIT

1.

Disconnect IPDM E/R connector.

2.

Check resistance between IPDM E/R harness connector E9 ter-
minals 48 (L) and 49 (Y).

OK or NG

OK

>> Replace IPDM E/R.

NG

>> Repair harness between IPDM E/R and ABS actuator

and electric unit (control unit).

11 (L) - 15 (Y) 

: Approx. 54 - 66

SKIA5019E

48 (L) - 49 (Y) 

: Approx. 108 - 132

LKIA0030E

CAN SYSTEM (TYPE 16)

LAN-559

[CAN]

C

D

E

F

G

H

I

J

L

M

A

B

LAN

Revision; 2004 April

2003 Murano

CAN Communication Circuit Check

AKS006XL

1. 

CHECK CONNECTOR

1.

Turn ignition switch OFF.

2.

Disconnect the negative battery terminal.

3.

Check following terminals and connectors for damage, bend and loose connection (control module side,
control unit side, meter side, sensor side and harness side).

ECM

TCM

Low tire pressure warning control unit

Display control unit

BCM

Unified meter and A/C amp.

Steering angle sensor

Driver seat control unit

ABS actuator and electric unit (control unit)

IPDM E/R

Between ECM and IPDM E/R

Between ECM and TCM

Between ECM and driver seat control unit

OK or NG

OK

>> GO TO 2.

NG

>> Repair terminal or connector.

LAN-560

[CAN]

CAN SYSTEM (TYPE 16)

Revision; 2004 April

2003 Murano

2. 

CHECK HARNESS FOR SHORT CIRCUIT

1.

Disconnect following connectors.

ECM connector

Low tire pressure warning control unit connector

Harness connector M82

Display control unit connector

BCM connector

Unified meter and A/C amp. connector

Steering angle sensor connector

Harness connector M9

2.

Check continuity between data link connector M24 terminals 6
(L) and 14 (Y).

OK or NG

OK

>> GO TO 3.

NG

>> Check the following harnesses. If any harness is dam-

aged, repair the harness.

Harness between data link connector and ECM.

Harness between data link connector and low tire
pressure warning control unit.

Harness between data link connector and harness connector M82.

Harness between data link connector and display control unit.

Harness between data link connector and BCM.

Harness between data link connector and unified meter and A/C amp.

Harness between data link connector and steering angle sensor.

Harness between data link connector and harness connector M9.

3. 

CHECK HARNESS FOR SHORT CIRCUIT

Check continuity between data link connector M24 terminals 6 (L),
14 (Y) and ground.

OK or NG

OK

>> GO TO 4.

NG

>> Check the following harnesses. If any harness is dam-

aged, repair the harness.

Harness between data link connector and ECM.

Harness between data link connector and low tire
pressure warning control unit.

Harness between data link connector and harness connector M82.

Harness between data link connector and display control unit.

Harness between data link connector and BCM.

Harness between data link connector and unified meter and A/C amp.

Harness between data link connector and steering angle sensor.

Harness between data link connector and harness connector M9.

6 (L) - 14 (Y) 

: Continuity should not exist.

PKIA2077E

6 (L) - Ground

: Continuity should not exist.

14 (Y) - Ground

: Continuity should not exist.

PKIA2079E

CAN SYSTEM (TYPE 16)

LAN-561

[CAN]

C

D

E

F

G

H

I

J

L

M

A

B

LAN

Revision; 2004 April

2003 Murano

4. 

CHECK HARNESS FOR SHORT CIRCUIT

1.

Disconnect TCM connector.

2.

Check continuity between TCM harness connector F103 termi-
nals 5 (L) and 6 (Y).

OK or NG

OK

>> GO TO 5.

NG

>> Repair harness between TCM and harness connector

F102.

5. 

CHECK HARNESS FOR SHORT CIRCUIT

Check continuity between TCM harness connector F103 terminals 5
(L), 6 (Y) and ground.

OK or NG

OK

>> GO TO 6.

NG

>> Repair harness between TCM and harness connector

F102.

6. 

CHECK HARNESS FOR SHORT CIRCUIT

1.

Disconnect harness connector B4 and harness connector B9.

2.

Check continuity between harness connector B4 terminals 3 (L)
and 10 (Y).

OK or NG

OK

>> GO TO 7.

NG

>> Check the following harnesses. If any harness is dam-

aged, repair the harness.

Repair harness between harness connector B4 and
harness connector B2.

Repair harness between harness connector B4 and
harness connector B9.

5 (L) - 6 (Y) 

: Continuity should not exist.

PKIA0817E

5 (L) - Ground

: Continuity should not exist.

6 (Y) - Ground

: Continuity should not exist.

SKIA5020E

3 (L) - 10 (Y) 

: Continuity should not exist.

SKIA5021E

LAN-562

[CAN]

CAN SYSTEM (TYPE 16)

Revision; 2004 April

2003 Murano

7. 

CHECK HARNESS FOR SHORT CIRCUIT

Check continuity between harness connector B4 terminals 3 (L), 10
(Y) and ground.

OK or NG

OK

>> GO TO 8.

NG

>> Check the following harnesses. If any harness is dam-

aged, repair the harness.

Repair harness between harness connector B4 and
harness connector B2.

Repair harness between harness connector B4 and harness connector B9.

8. 

CHECK HARNESS FOR SHORT CIRCUIT

1.

Disconnect driver seat control unit connector.

2.

Check continuity between driver seat control unit harness con-
nector B303 terminals 3 (L/Y) and 19 (BR/W).

OK or NG

OK

>> GO TO 9.

NG

>> Repair harness between driver seat control unit and har-

ness connector B301.

9. 

CHECK HARNESS FOR SHORT CIRCUIT

Check continuity between driver seat control unit harness connector
B303 terminals 3 (L/Y), 19 (BR/W) and ground.

OK or NG

OK

>> GO TO 10.

NG

>> Repair harness between driver seat control unit and har-

ness connector B301.

3 (L) - Ground

: Continuity should not exist.

10 (Y) - Ground

: Continuity should not exist.

SKIA5022E

3 (L/Y) - 19 (BR/W) 

: Continuity should not exist.

SKIA5024E

3 (L/Y) - Ground

: Continuity should not exist.

19 (BR/W) - Ground

: Continuity should not exist.

SKIA5025E

CAN SYSTEM (TYPE 16)

LAN-563

[CAN]

C

D

E

F

G

H

I

J

L

M

A

B

LAN

Revision; 2004 April

2003 Murano

10. 

CHECK HARNESS FOR SHORT CIRCUIT

1.

Disconnect ABS actuator and electric unit (control unit) connector and IPDM E/R connector.

2.

Check continuity between IPDM E/R harness connector E9 ter-
minals 48 (L) and 49 (Y).

OK or NG

OK

>> GO TO 11.

NG

>> Check the following harnesses. If any harness is dam-

aged, repair the harness.

Harness between IPDM E/R and ABS actuator and
electric unit (control unit).

Harness between IPDM E/R and harness connector
E105.

11. 

CHECK HARNESS FOR SHORT CIRCUIT

Check continuity between IPDM E/R harness connector E9 termi-
nals 48 (L), 49 (Y) and ground.

OK or NG

OK

>> GO TO 12.

NG

>> Check the following harnesses. If any harness is dam-

aged, repair the harness.

Harness between IPDM E/R and ABS actuator and
electric unit (control unit).

Harness between IPDM E/R and harness connector E105.

12. 

ECM/IPDM E/R INTERNAL CIRCUIT INSPECTION

Check components inspection. Refer to 

LAN-563, "ECM/IPDM E/R INTERNAL CIRCUIT INSPECTION"

 .

OK or NG

OK

>> Connect all the connectors and diagnose again. Refer to 

LAN-532, "Work Flow"

 .

NG

>> Replace ECM and/or IPDM E/R.

IPDM E/R Ignition Relay Circuit Check

AKS006XM

Check the following. If no malfunction is found, replace the IPDM E/R.

IPDM E/R power supply circuit. Refer to 

PG-45, "IPDM E/R Power/Ground Circuit Inspection"

 .

Ignition power supply circuit. Refer to 

PG-10, "IGNITION POWER SUPPLY - IGNITION SW. IN “ON”

AND/OR “START”"

 .

Component Inspection

AKS006XN

ECM/IPDM E/R INTERNAL CIRCUIT INSPECTION

Remove ECM and IPDM E/R from vehicle.

Check resistance between ECM terminals 94 and 86.

Check resistance between IPDM E/R terminals 48 and 49.

48 (L) - 49 (Y) 

: Continuity should not exist.

LKIA0030E

48 (L) - Ground

: Continuity should not exist.

49 (Y) - Ground

: Continuity should not exist.

LKIA0036E

Unit

Terminal

Resistance value (

)

(Approx.)

ECM

94 - 86

108 - 132

IPDM E/R

48 - 49

LKIA0037E

LAN-564

[CAN]

CAN SYSTEM (TYPE 17)

Revision; 2004 April

2003 Murano

CAN SYSTEM (TYPE 17)

PFP:23710

System Description

AKS006XO

CAN (Controller Area Network) is a serial communication line for real time application. It is an on-vehicle mul-
tiplex communication line with high data communication speed and excellent error detection ability. Many elec-
tronic control units are equipped onto a vehicle, and each control unit shares information and links with other
control units during operation (not independent). In CAN communication, control units are connected with 2
communication lines (CAN H line, CAN L line) allowing a high rate of information transmission with less wiring.
Each control unit transmits/receives data but selectively reads required data only.

Component Parts and Harness Connector Location

AKS006XP

SKIA5863E

CAN SYSTEM (TYPE 17)

LAN-565

[CAN]

C

D

E

F

G

H

I

J

L

M

A

B

LAN

Revision; 2004 April

2003 Murano

Schematic

AKS006XQ

TKWA0987E

LAN-566

[CAN]

CAN SYSTEM (TYPE 17)

Revision; 2004 April

2003 Murano

Wiring Diagram - CAN -

AKS006XR

TKWA0988E

CAN SYSTEM (TYPE 17)

LAN-567

[CAN]

C

D

E

F

G

H

I

J

L

M

A

B

LAN

Revision; 2004 April

2003 Murano

TKWA0989E

LAN-568

[CAN]

CAN SYSTEM (TYPE 17)

Revision; 2004 April

2003 Murano

TKWA0990E

CAN SYSTEM (TYPE 17)

LAN-569

[CAN]

C

D

E

F

G

H

I

J

L

M

A

B

LAN

Revision; 2004 April

2003 Murano

Work Flow

AKS00C5I

1.

When there are no indications of “TRANSMISSION” or “METER A/C AMP” on “SELECT SYSTEM” dis-
play of CONSULT-II, print the “SELECT SYSTEM”.

2.

Print all the data of “SELF-DIAG RESULTS” for “ENGINE”, “TRANSMISSION”, “BCM”, “METER A/C
AMP”, “ALL MODE AWD/4WD” and “ABS” displayed on CONSULT-II.

3.

Print all the data of “CAN DIAG SUPPORT MNTR” for “ENGINE”, “TRANSMISSION”, “BCM”, “METER A/
C AMP”, “ALL MODE AWD/4WD” and “ABS” displayed on CONSULT-II.

4.

Attach the printed sheet of “SELECT SYSTEM”, “SELF-DIAG RESULTS” and “CAN DIAG SUPPORT
MNTR” onto the check sheet. Refer to 

LAN-571, "CHECK SHEET"

 .

5.

Based on the indications of “SELECT SYSTEM” and the results of “CAN DIAG SUPPORT MNTR”, put
marks “v” onto the items with “No indication”, “NG”, or “UNKWN” in the check sheet table. Refer to 

LAN-

571, "CHECK SHEET"

 .

NOTE:

If “NG” is displayed on “INITIAL DIAG (Initial diagnosis)” as “CAN DIAG SUPPORT MNTR” for the diag-
nosed control unit, replace the control unit.

The “CAN DIAG SUPPORT MNTR” items, which are not in check sheet table, are not related to diag-
nostic procedure on service manual.
So it is not necessary to check the status of “CAN DIAG SUPPORT MNTR” items which are not indi-
cated in check sheet table.

6.

Check CAN communication line of the integrated display system. Refer to 

AV-110, "CAN Communication

Line Check"

 .

7.

Attach the CAN DIAG MONITOR check sheet onto the check sheet. Refer to 

LAN-571, "CHECK SHEET"

.

PKIA2093E

PKIA8260E

PKIA8343E

LAN-570

[CAN]

CAN SYSTEM (TYPE 17)

Revision; 2004 April

2003 Murano

8.

Mark the “NG” or “UNKWN” item of the check sheet table with “v” from the result of CAN DIAG MONITOR
check sheet. Refer to 

LAN-569, "Work Flow"

 .

NOTE:
If “NG” is displayed on “CAN COMM” as “CAN DIAG MNTR” for the diagnosed control unit, replace the
control unit. Refer to 

AV-110, "CAN Communication Line Check"

 .

9.

According to the check sheet results (example), start inspection. Refer to 

LAN-573, "CHECK SHEET

RESULTS (EXAMPLE)"

 .

CAN SYSTEM (TYPE 17)

LAN-571

[CAN]

C

D

E

F

G

H

I

J

L

M

A

B

LAN

Revision; 2004 April

2003 Murano

CHECK SHEET

NOTE:
If “NG” is displayed on “INITIAL DIAG (Initial diagnosis)” or “CAN COMM” for the diagnosed control unit,
replace the control unit.

PKIB0714E

LAN-572

[CAN]

CAN SYSTEM (TYPE 17)

Revision; 2004 April

2003 Murano

PKIB0715E

CAN SYSTEM (TYPE 17)

LAN-573

[CAN]

C

D

E

F

G

H

I

J

L

M

A

B

LAN

Revision; 2004 April

2003 Murano

CHECK SHEET RESULTS (EXAMPLE)

NOTE:
If “NG” is displayed on “INITIAL DIAG (Initial diagnosis)” or “CAN COMM” for the diagnosed control unit,
replace the control unit.

Case 1

Check harness between TCM and data link connector. Refer to 

LAN-585, "Circuit Check Between TCM and

Data Link Connector"

 .

PKIB0716E

SKIA5336E

 

 

 

 

 

 

 

Content      ..     182      183      184      185     ..