Nissan Murano Z51 (2008 year). Manual - part 385

 

  Index      Manuals     Nissan Murano Z51 (2008 year) - Service and Repair Manual

 

Search            copyright infringement  

 

 

 

 

 

 

 

 

Content      ..     383      384      385      386     ..

 

 

Nissan Murano Z51 (2008 year). Manual - part 385

 

 

TRANSMISSION CONTROL MODULE

TM-163

< ON-VEHICLE REPAIR >

[CVT: RE0F09B]

C

E

F

G

H

I

J

K

L

M

A

B

TM

N

O

P

ON-VEHICLE REPAIR

TRANSMISSION CONTROL MODULE

Exploded View

INFOID:0000000003306167

Removal and Installation

INFOID:0000000003306168

REMOVAL

CAUTION:

Never impact on TCM when removing or installing TCM.

1.

Disconnect the battery cable from the negative terminal.

2.

Remove air duct (inlet). Refer to 

EM-27, "Exploded View"

.

3.

Disconnect TCM connector (A).

4.

Remove TCM (1) from bracket.

INSTALLATION

Install in the reverse order of removal.

1.

Bracket

2.

TCM

: Vehicle front

Refer to 

GI-4, "Components"

 for symbols in the figure. 

JPDIA0591GB

: Vehicle front

JPDIA0596ZZ

Revision: 2008 October

2009 Murano

TM-164

< ON-VEHICLE REPAIR >

[CVT: RE0F09B]

TRANSMISSION CONTROL MODULE

Adjustment

INFOID:0000000003306169

ADJUSTMENT AFTER INSTALLATION

After TCM is replaced. Refer to 

TM-8, "ADDITIONAL SERVICE WHEN REPLACING CONTROL UNIT : Pre-

caution for TCM and CVT Assembly Replacement"

.

Revision: 2008 October

2009 Murano

CONTROL DEVICE

TM-165

< ON-VEHICLE REPAIR >

[CVT: RE0F09B]

C

E

F

G

H

I

J

K

L

M

A

B

TM

N

O

P

CONTROL DEVICE

Exploded View

INFOID:0000000003306170

Removal and Installation

INFOID:0000000003306171

REMOVAL

1.

Disconnect the battery cable from the negative terminal.

2.

Move selector lever to “N” position.

1.

Selector lever knob

2.

Lock pin

3.

Knob cover

4.

Control device assembly

5.

Shift lock unit

Refer to 

GI-4, "Components"

 for symbols in the figure. 

JPDIA0610GB

Revision: 2008 October

2009 Murano

TM-166

< ON-VEHICLE REPAIR >

[CVT: RE0F09B]

CONTROL DEVICE

3.

Slide knob cover (1) below selector lever downward.

CAUTION:

Be careful not to damage knob cover.

4.

Pull lock pin (2) out of selector lever knob (3).

5.

Remove selector lever knob and knob cover.

6.

Remove center console assembly. Refer to 

IP-19, "Exploded

View"

.

7.

Move selector lever to “P” position.

8.

Remove control cable (1) from control device assembly. Refer to

TM-167, "Exploded View"

.

9.

Remove control device assembly (2).

10. Remove control device connector (A) using a flat-bladed screw-

driver (B).

11. Remove shift lock unit from control device assembly.

INSTALLATION

Note the following, and install in the reverse order of removal.
When installing control cable (1) to control device assembly (2),
check that control cable is fully pressed in with the ribbed (A) surface
facing upward.

Inspection and Adjustment

INFOID:0000000003306172

ADJUSTMENT AFTER INSTALLATION

Adjust the CVT positions after installing control device. Refer to 

TM-162, "Inspection and Adjustment"

.

INSPECTION AFTER INSTALLATION

Check the CVT positions after adjusting the CVT positions. Refer to 

TM-162, "Inspection and Adjustment"

.

JPDIA0606ZZ

: Nut

JPDIA0615ZZ

JPDIA0616ZZ

JPDIA0609ZZ

Revision: 2008 October

2009 Murano

CONTROL CABLE

TM-167

< ON-VEHICLE REPAIR >

[CVT: RE0F09B]

C

E

F

G

H

I

J

K

L

M

A

B

TM

N

O

P

CONTROL CABLE

Exploded View

INFOID:0000000003306176

Removal and Installation

INFOID:0000000003306177

REMOVAL

CAUTION:

Make sure that parking brake is applied before removal/installation.
1.

Remove control cable from control device assembly. Refer to 

TM-165, "Exploded View"

.

2.

Remove air duct (inlet). Refer to 

EM-27, "Exploded View"

.

3.

Remove battery and battery bracket. Refer to 

PG-106, "Exploded View"

.

4.

Remove air cleaner case. Refer to 

EM-27, "Exploded View"

.

5.

Remove nut (

).

6.

Remove control cable (1) from manual lever (A).

7.

Remove lock plate (2) from control cable.

8.

Remove control cable from bracket (3).

9.

Remove front foot duct RH. Refer to 

VTL-60, "REAR FOOT

DUCT 1 : Exploded View"

 (without 7 inch display), 

VTL-116,

"REAR VENTILATOR DUCT 1 : Exploded View"

 (with 7 inch dis-

play).

1.

Control device assembly

2.

Control cable

3.

Lock plate

4.

Bracket

5.

Transaxle assembly

Refer to 

GI-4, "Components"

 for symbols in the figure.

JPDIA0611GB

JPDIA0601ZZ

Revision: 2008 October

2009 Murano

TM-168

< ON-VEHICLE REPAIR >

[CVT: RE0F09B]

CONTROL CABLE

10. Remove the control cable (1) from the vehicle.

INSTALLATION

Note the following, and install in the reverse order of removal.
When installing control cable (1) to control device assembly (2),
check that control cable is fully pressed in with the ribbed (A) surface
facing upward.

Inspection and Adjustment

INFOID:0000000003306178

ADJUSTMENT AFTER INSTALLATION

Adjust the CVT positions after installing control cable. Refer to 

TM-162, "Inspection and Adjustment"

.

INSPECTION AFTER INSTALLATION

Check the CVT positions after adjusting the CVT positions. Refer to 

TM-162, "Inspection and Adjustment"

.

A

: Dash trim

: Bolt

JPDIA0629ZZ

JPDIA0609ZZ

Revision: 2008 October

2009 Murano

OIL PAN

TM-169

< ON-VEHICLE REPAIR >

[CVT: RE0F09B]

C

E

F

G

H

I

J

K

L

M

A

B

TM

N

O

P

OIL PAN

Exploded View

INFOID:0000000003306182

Removal and Installation

INFOID:0000000003306183

REMOVAL

1.

Remove engine under cover with power tool.

2.

Remove drain plug.

3.

Remove O-ring from drain plug.

4.

Remove oil pan fitting bolts (

).

5.

Remove oil pan.

1.

Transaxle assembly

2.

Oil pan fitting bolt

3.

Drain plug

4.

O-ring

5.

Oil pan

6.

Oil pan gasket

7.

Magnet

: Apply CVT Fluid NS-2.

Refer to 

GI-4, "Components"

 for symbols in the figure.

JPDIA0608GB

: Vehicle front

SCIA8135J

Revision: 2008 October

2009 Murano

TM-170

< ON-VEHICLE REPAIR >

[CVT: RE0F09B]

OIL PAN

6.

Remove oil pan gasket (1) from oil pan (2).

7.

Remove magnet (3) from oil pan.

INSTALLTION

Note the following, and install in the reverse order of removal.

CAUTION:

• Completely remove all moisture, oil and old gasket, etc. from the oil pan gasket mounting surface of

transaxle case and oil pan.

• Never reuse oil pan gasket, O-ring and oil pan fitting bolts.
• Apply CVT fluid to O-ring.

Inspection

INFOID:0000000003306184

Check foreign materials in oil pan to help determine causes of malfunction. If the CVT fluid is very dark, smells
burned, or contains foreign particles, frictional material (clutches) may need replacement. A tacky film that will
not wipe clean indicates varnish build up. Varnish can cause valves and clutches to stick and can inhibit pump
pressure.

INSPECTION AFTER INSTALLATION

Check for CVT fluid leakage and check CVT fluid level. Refer to 

TM-149, "Inspection"

.

SCIA8219J

Revision: 2008 October

2009 Murano

SECONDARY SPEED SENSOR

TM-171

< ON-VEHICLE REPAIR >

[CVT: RE0F09B]

C

E

F

G

H

I

J

K

L

M

A

B

TM

N

O

P

SECONDARY SPEED SENSOR

Exploded View

INFOID:0000000003306191

Removal and Installation

INFOID:0000000003306192

REMOVAL

1.

Disconnect the battery cable from negative terminal.

2.

Remove air duct (inlet). Refer to 

EM-27, "Exploded View"

.

3.

Remove air cleaner case. Refer to 

EM-27, "Exploded View"

4.

Disconnect secondary speed sensor connector.

5.

Remove secondary speed sensor (1) and shim (2).

CAUTION:

Never lose the shim.

6.

Remove O-ring (3) from secondary speed sensor.

INSTALLATION

Note the following, and install in the reverse order of removal.

CAUTION:

• Never reuse O-ring.
• Apply CVT fluid to O-ring.

Inspection

INFOID:0000000003306193

INSPECTION AFTER INSTALLATION

Check for CVT fluid leakage and check CVT fluid level. Refer to 

TM-149, "Inspection"

.

1.

Secondary speed sensor

2.

Shim

3.

Transaxle assembly

4.

O-ring

: Apply CVT Fluid NS-2.

Refer to 

GI-4, "Components"

 for symbols not described above.

JPDIA0687GB

JPDIA0617ZZ

Revision: 2008 October

2009 Murano

TM-172

< ON-VEHICLE REPAIR >

[CVT: RE0F09B]

DIFFERENTIAL SIDE OIL SEAL

DIFFERENTIAL SIDE OIL SEAL

2WD

2WD : Exploded View

INFOID:0000000003306194

2WD : Removal and Installation

INFOID:0000000003306195

REMOVAL

1.

Remove front drive shafts. Refer to 

FAX-17, "Exploded View"

.

2.

Remove differential side oil seals (1) using a flat-bladed screw-
driver (A).

CAUTION:

Be careful not to scratch transaxle case and converter
housing.

INSTALLTION

Note the following, and install in the reverse order of removal.
• Drive each differential side oil seal evenly using a commercial ser-

vice tool so that differential side oil seal protrudes by the dimension
(C) respectively.

Unit: mm (in)

NOTE:
Differential side oil seal pulling direction is used as the reference.

1.

RH differential side oil seal

2.

LH differential side oil seal

3.

Transaxle assembly

: Apply CVT Fluid NS-2.

Refer to 

GI-4, "Components"

 for symbols not described above.

JPDIA0593ZZ

JPDIA0118ZZ

A

: Transaxle case side

B

: Converter housing side

Dimension C 

±

 0.5 (0 

±

 0.020)

JPDIA0618ZZ

Revision: 2008 October

2009 Murano

DIFFERENTIAL SIDE OIL SEAL

TM-173

< ON-VEHICLE REPAIR >

[CVT: RE0F09B]

C

E

F

G

H

I

J

K

L

M

A

B

TM

N

O

P

CAUTION:

• Never reuse differential side oil seals.
• Apply CVT fluid to differential side oil seals.

Drift to be used:

2WD : Inspection

INFOID:0000000003306196

INSPECTION AFTER INSTALLATION

Check for CVT fluid leakage and check CVT fluid level. Refer to 

TM-149, "Inspection"

.

AWD

AWD : Exploded View

INFOID:0000000003306197

AWD : Removal and Installation

INFOID:0000000003306198

REMOVAL

1.

Remove exhaust front tube. Refer to 

EX-5, "Exploded View"

.

2.

Separate propeller shaft. Refer to 

DLN-80, "Exploded View"

.

3.

Remove front drive shafts. Refer to 

FAX-44, "Exploded View"

.

4.

Remove transfer from transaxle assembly. Refer to 

DLN-51, "Exploded View"

.

Location

Tool number (Kent-Moore No.)

Transaxle case side

ST33400001 (J-26082)

Converter housing side

1.

Side oil seal (transfer joint)

2.

LH differential side oil seal

3.

Transaxle assembly

: Apply CVT Fluid NS-2.

Refer to 

GI-4, "Components"

 for symbols not described above.

JPDIA0594ZZ

Revision: 2008 October

2009 Murano

TM-174

< ON-VEHICLE REPAIR >

[CVT: RE0F09B]

DIFFERENTIAL SIDE OIL SEAL

5.

Remove differential side oil seal (1) and side oil seal (transfer
joint) using a flat-bladed screwdriver (A).

CAUTION:

Be careful not to scratch transaxle case and converter
housing.

INSTALLTION

Note the following, and install in the reverse order of removal.
• Drive each differential side oil seal and side oil seal (transfer joint)

evenly using a commercial service tool so that differential side oil
seal and side oil seal (transfer joint) protrudes by the dimension
(C) respectively.

Unit: mm (in)

NOTE:
Differential side oil seal and side oil seal (transfer joint) pulling direc-
tion is used as the reference.

CAUTION:

• Never reuse differential side oil seals and side oil seal (transfer joint).
• Apply CVT fluid to differential side oil seals and side oil seal (transfer joint).

Drift to be used:

AWD : Inspection

INFOID:0000000003306199

INSPECTION AFTER INSTALLATION

Check for CVT fluid leakage and check CVT fluid level. Refer to 

TM-149, "Inspection"

.

JPDIA0118ZZ

A

: Transaxle case side

B

: Converter housing side

Dimension C

±

 0.5 (0 

±

 0.020)

JPDIA0619ZZ

Location

Tool number (Kent-Moore No.)

Differential side oil seal

ST33400001 (J-26082)

Side oil seal (transfer joint)

KV40100621 (J-25405)

Revision: 2008 October

2009 Murano

AIR BREATHER HOSE

TM-175

< ON-VEHICLE REPAIR >

[CVT: RE0F09B]

C

E

F

G

H

I

J

K

L

M

A

B

TM

N

O

P

AIR BREATHER HOSE

Exploded View

INFOID:0000000003306204

Removal and Installation

INFOID:0000000003306205

REMOVAL

1.

Remove air duct (inlet). Refer to 

EM-27, "Exploded View"

.

2.

Remove air cleaner case. Refer to 

EM-27, "Exploded View"

.

3.

Remove air breather hose from transaxle assembly.

INSTALLATION

Note the following, and install in the reverse order of removal.

CAUTION:

Check that air breather hose is not collapsed or blocked due to folding or bending when installed.
• Install air breather hose to air breather tube so that the paint mark

(A) faces upward. Also insert hose to the bend of air breather tube.

1.

Air cleaner case

2.

Air breather hose

3.

Transaxle assembly

4.

Heater pipe

: Vehicle front

JPDIA0592ZZ

SCIA7584J

Revision: 2008 October

2009 Murano

TM-176

< REMOVAL AND INSTALLATION >

[CVT: RE0F09B]

TRANSAXLE ASSEMBLY

REMOVAL AND INSTALLATION

TRANSAXLE ASSEMBLY

Exploded View

INFOID:0000000003306215

Removal and Installation

INFOID:0000000003306216

WARNING:

Never remove the reservoir tank cap when the engine is hot. Serious burns could occur from high-
pressure engine coolant escaping from the reservoir tank.

REMOVAL

1.

Remove the engine, the transaxle, transfer (AWD models) assembly and front suspension member. Refer
to 

EM-68, "2WD : Exploded View"

 (2WD), 

EM-77, "AWD : Exploded View"

 (AWD).

1.

Air breather hose

2.

CVT fluid level gauge

3.

CVT fluid charging pipe

4.

O-ring

5.

Copper washer

6.

fluid cooler tube

7.

Transaxle assembly

A.

For tightening torque, refer to 

TM-176, "Removal and Installation"

.

Refer to 

GI-4, "Components"

 for symbols in the figure.

JPDIA0626GB

Revision: 2008 October

2009 Murano

TRANSAXLE ASSEMBLY

TM-177

< REMOVAL AND INSTALLATION >

[CVT: RE0F09B]

C

E

F

G

H

I

J

K

L

M

A

B

TM

N

O

P

2.

Lift with hoist and separate engine, transaxle and transfer (AWD models) assembly from front suspension
member. Refer to 

EM-68, "2WD : Exploded View"

 (2WD), 

EM-77, "AWD : Exploded View"

 (AWD).

3.

Remove air breather hose. Refer to 

TM-175, "Exploded View"

.

4.

Disconnect secondary speed sensor connector. Refer to 

TM-171, "Exploded View"

.

5.

Disconnect CVT unit connector.

6.

Disconnect air fuel ratio sensor 1 (bank 2). Refer to 

EM-34, "Exploded View"

.

7.

Remove crankshaft position sensor (POS). Refer to 

EM-39, "Exploded View"

.

8.

Remove CVT fluid charging pipe from transaxle assembly.

9.

Remove transaxle assembly fixing bolts with power tool.

10. Remove transaxle assembly from engine assembly with a hoist.

11. Remove CVT fluid cooler hose from transaxle assembly.

INSTALLATION

Note the following, and install in the reverse order of removal.

CAUTION:

Check fitting of dowel pins (

) when installing transaxle

assembly to engine assembly.

When installing CVT fluid cooler tube (1) to transaxle assembly:
• Contact CVT fluid cooler tube a boss portion (A) of the transaxle

case.

• Tighten the bolt of CVT fluid cooler tube without moving the CVT

fluid cooler tube.

JPDIA0598ZZ

JPDIA0602ZZ

JPDIA0628ZZ

Revision: 2008 October

2009 Murano

TM-178

< REMOVAL AND INSTALLATION >

[CVT: RE0F09B]

TRANSAXLE ASSEMBLY

When installing transaxle assembly to the engine assembly, attach
the fixing bolts in accordance with the following.

• When using the drive plate location guide (commercial service tool:

31197CA000) (A), set it to the stud bolts which is used to install it
to the torque converter.

• When not using drive plate location guide, rotate torque converter

so that the stud bolt (B) for mounting the drive plate location guide
of torque converter aligns with the mounting position of service
hole.

• Rotate crankshaft so that the hole (A) for inserting drive plate loca-

tion guide of drive plate aligns with the service hole (B).
NOTE:
When not using drive plate location guide, insert stud bolt of torque
converter into the hole (C) of drive plate, aligning the drive plate
hole position and torque converter.

CAUTION:

Be careful not to strike the drive plate when installing the
torque converter stud bolt.

• Align the position of tightening nuts (

) for drive plate with those

of the torque converter, and temporarily tighten the nuts. Then,
tighten the bolts to the specified torque. 

CAUTION:

• When turning crankshaft, turn it clockwise as viewed from the

front of the engine.

• When tightening the nuts for the torque converter after fixing

the crankshaft pulley bolts, confirm the tightening torque of
the crankshaft pulley mounting bolts. Refer to 

EM-89,

"Exploded View"

.

JPDIA0600ZZ

Insertion direction

Transaxle assembly to engine assembly

Engine assembly to tran-

saxle assembly

Bolt position

A

B

C

D

Number of bolts

1

2

2

4

Bolt length

mm (in)

55 (2.17)

39 (1.54)

108 (4.25)

45 (1.77)

Tightening torque
N·m (kg-m, ft-lb)

74.5 (7.6, 55)

50 (5.1, 37)

JPDIA0607ZZ

JPDIA0603ZZ

: 51 N·m (5.2 kg-m, 38 ft-lb)

SCIA1861E

Revision: 2008 October

2009 Murano

 

 

 

 

 

 

 

Content      ..     383      384      385      386     ..