Nissan Murano Z51 (2008 year). Manual

SRC-80

< COMPONENT DIAGNOSIS >

[FOR USA AND CANADA]

B1084 PRE-TEN FRONT RH

B1084 PRE-TEN FRONT RH

Description

INFOID:0000000003367406

DTC B1084 [SHORT] PRE-TEN FRONT RH

For front RH seat belt pre-tensioner, crash is judged by main “G” sensor output signal and Safing algorithm in
front direction.

OPERATION

In the case of a frontal collision that exceeds specified impact level, the air bag diagnosis sensor unit detects
the deceleration caused by collision. It restrains the passenger with seat belt easing the stress on passengers
chest with load limiter.

STRUCTURE

The restraint system for front seat occupant consists of the pre-tensioner mechanism and load limiter mecha-
nism.

INSTALLATION

Front RH seat belt pre-tensioner is installed on the underside of center pillar with fixed nuts.

DTC Logic

INFOID:0000000003367407

DTC DETECTION LOGIC

With CONSULT-lll

DTC No. Index (“SELF-DIAG [CURRENT]”), (“SELF-DIAG [PAST]” or “TROUBLE DIAG RECORD”)

DTC CONFIRMATION PROCEDURE (With CONSULT-lll)

INSPECTION START

Turn ignition switch ON.

>> GO TO 2.

CHECK SELF-DIAG RESULT

Check the screen of CONSULT-lll.

Is malfunctioning part detected?

YES

>> Refer to

SRC-81, "Diagnosis Procedure"

>> INSPECTION END.

DTC CONFIRMATION PROCEDURE (Without CONSULT-lll)

NOTE:
• SRS will not enter diagnosis mode if no malfunction is detected in user mode.

INSPECTION START

Turn ignition switch ON.

DTC No.

Trouble diagnosis name

DTC detecting condition

Possible cause

B1084

PRE-TEN FRONT RH
[SHORT]

Front RH seat belt pre-tensioner circuit
are shorted to each other

• Disconnection of wiring harness and

short

• Internal breakdown in front RH seat

belt pre-tensioner

• Internal breakdown in air bag diag-

nosis sensor unit

Revision: 2008 October

2009 Murano

B1084 PRE-TEN FRONT RH

SRC-81

< COMPONENT DIAGNOSIS >

[FOR USA AND CANADA]

SRC

>> GO TO 2.

CHECK AIR BAG WARNING LAMP

Check the air bag warning lamp status.

Is malfunctioning part detected?

YES

>> Refer to warning lamp flash code chart.

SRC-142

>> INSPECTION END.

Diagnosis Procedure

INFOID:0000000003367408

With CONSULT-lll

WARNING:

• Before servicing, turn ignition switch OFF, disconnect battery negative terminal and wait at least 3

minutes. (To discharge backup capacitor.)

• Do not use unspecified tester or other measuring device.

DIAGNOSTIC PROCEDURE

CHECK HARNESS CONNECTOR

Check the connection of harness connector.
Is the inspection result normal?

YES

>> GO TO 2.

>> Repair or replace harness connector.

CHECK WIRING HARNESS

Check the wiring harness externals.
Is the inspection result normal?

YES

>> GO TO 3.

>> Repair or replace wiring harness.

CHECK FRONT SEAT BELT PRE-TENSIONER

Replace front RH seat belt pre-tensioner.

Check the screen of CONSULT-lll.

Is the inspection result normal?

YES

>> INSPECTION END.

>> Check the intermittent incident. Refer to

GI-40, "Intermittent Incident"

Revision: 2008 October

2009 Murano

SRC-82

< COMPONENT DIAGNOSIS >

[FOR USA AND CANADA]

B1086 PRE-TEN FRONT LH

B1086 PRE-TEN FRONT LH

Description

INFOID:0000000003367409

DTC B1086 [OPEN] PRE-TEN FRONT LH

For front LH seat belt pre-tensioner, crash is judged by main “G” sensor output signal and Safing algorithm in
front direction.

OPERATION

STRUCTURE

The restraint system for front seat occupant consists of the pre-tensioner mechanism and load limiter mecha-
nism.

INSTALLATION

Front LH seat belt pre-tensioner is installed on the underside of center pillar with fixed nuts.

DTC Logic

INFOID:0000000003367410

DTC DETECTION LOGIC

With CONSULT-lll

DTC No. Index (“SELF-DIAG [CURRENT]”), (“SELF-DIAG [PAST]” or “TROUBLE DIAG RECORD”)

DTC CONFIRMATION PROCEDURE (With CONSULT-lll)

INSPECTION START

Turn ignition switch ON.

>> GO TO 2.

CHECK SELF-DIAG RESULT

Check the screen of CONSULT-lll.

Is malfunctioning part detected?

YES

>> Refer to

SRC-83, "Diagnosis Procedure"

>> INSPECTION END.

DTC CONFIRMATION PROCEDURE (Without CONSULT-lll)

NOTE:
• SRS will not enter diagnosis mode if no malfunction is detected in user mode.

INSPECTION START

Turn ignition switch ON.

DTC No.

Trouble diagnosis name

DTC detecting condition

Possible cause

B1086

PRE-TEN FRONT LH
[OPEN]

Front LH seat belt pre-tensioner circuit
is open

• Disconnection of wiring harness and

open

• Internal breakdown in front LH seat

belt pre-tensioner

• Internal breakdown in air bag diag-

nosis sensor unit

Revision: 2008 October

2009 Murano

B1086 PRE-TEN FRONT LH

SRC-83

< COMPONENT DIAGNOSIS >

[FOR USA AND CANADA]

SRC

>> GO TO 2.

CHECK AIR BAG WARNING LAMP

Check the air bag warning lamp status.

Is malfunctioning part detected?

YES

>> Refer to warning lamp flash code chart.

SRC-142

>> INSPECTION END.

Diagnosis Procedure

INFOID:0000000003367411

With CONSULT-lll

WARNING:

• Before servicing, turn ignition switch OFF, disconnect battery negative terminal and wait at least 3

minutes. (To discharge backup capacitor.)

• Do not use unspecified tester or other measuring device.

DIAGNOSTIC PROCEDURE

CHECK HARNESS CONNECTOR

Check the connection of harness connector.
Is the inspection result normal?

YES

>> GO TO 2.

>> Repair or replace harness connector.

CHECK WIRING HARNESS

Check the wiring harness externals.
Is the inspection result normal?

YES

>> GO TO 3.

>> Repair or replace wiring harness.

CHECK FRONT SEAT BELT PRE-TENSIONER

Replace front LH seat belt pre-tensioner.

Check the screen of CONSULT-lll.

Is the inspection result normal?

YES

>> INSPECTION END.

>> Check the intermittent incident. Refer to

GI-40, "Intermittent Incident"

Revision: 2008 October

2009 Murano

SRC-84

< COMPONENT DIAGNOSIS >

[FOR USA AND CANADA]

B1087 PRE-TEN FRONT LH

B1087 PRE-TEN FRONT LH

Description

INFOID:0000000003367412

DTC B1087 [VB-SHORT] PRE-TEN FRONT LH

For front LH seat belt pre-tensioner, crash is judged by main “G” sensor output signal and Safing algorithm in
front direction.

OPERATION

STRUCTURE

The restraint system for front seat occupant consists of the pre-tensioner mechanism and load limiter mecha-
nism.

INSTALLATION

Front LH seat belt pre-tensioner is installed on the underside of center pillar with fixed nuts.

DTC Logic

INFOID:0000000003367413

DTC DETECTION LOGIC

With CONSULT-lll

DTC No. Index (“SELF-DIAG [CURRENT]”), (“SELF-DIAG [PAST]” or “TROUBLE DIAG RECORD”)

DTC CONFIRMATION PROCEDURE (With CONSULT-lll)

INSPECTION START

Turn ignition switch ON.

>> GO TO 2.

CHECK SELF-DIAG RESULT

Check the screen of CONSULT-lll.

Is malfunctioning part detected?

YES

>> Refer to

SRC-85, "Diagnosis Procedure"

>> INSPECTION END.

DTC CONFIRMATION PROCEDURE (Without CONSULT-lll)

NOTE:
• SRS will not enter diagnosis mode if no malfunction is detected in user mode.

INSPECTION START

Turn ignition switch ON.

DTC No.

Trouble diagnosis name

DTC detecting condition

Possible cause

B1087

PRE-TEN FRONT LH
[VB-SHORT]

Front LH seat belt pre-tensioner circuit
is shorted to some power supply circuit

• Disconnection of wiring harness and

short

• Internal breakdown in front LH seat

belt pre-tensioner

• Internal breakdown in air bag diag-

nosis sensor unit

Revision: 2008 October

2009 Murano

B1087 PRE-TEN FRONT LH

SRC-85

< COMPONENT DIAGNOSIS >

[FOR USA AND CANADA]

SRC

>> GO TO 2.

CHECK AIR BAG WARNING LAMP

Check the air bag warning lamp status.

Is malfunctioning part detected?

YES

>> Refer to warning lamp flash code chart.

SRC-142

>> INSPECTION END.

Diagnosis Procedure

INFOID:0000000003367414

With CONSULT-lll

WARNING:

• Before servicing, turn ignition switch OFF, disconnect battery negative terminal and wait at least 3

minutes. (To discharge backup capacitor.)

• Do not use unspecified tester or other measuring device.

DIAGNOSTIC PROCEDURE

CHECK HARNESS CONNECTOR

Check the connection of harness connector.
Is the inspection result normal?

YES

>> GO TO 2.

>> Repair or replace harness connector.

CHECK WIRING HARNESS

Check the wiring harness externals.
Is the inspection result normal?

YES

>> GO TO 3.

>> Repair or replace wiring harness.

CHECK FRONT SEAT BELT PRE-TENSIONER

Replace front LH seat belt pre-tensioner.

Check the screen of CONSULT-lll.

Is the inspection result normal?

YES

>> INSPECTION END.

>> Check the intermittent incident. Refer to

GI-40, "Intermittent Incident"

Revision: 2008 October

2009 Murano

SRC-86

< COMPONENT DIAGNOSIS >

[FOR USA AND CANADA]

B1088 PRE-TEN FRONT LH

B1088 PRE-TEN FRONT LH

Description

INFOID:0000000003367415

DTC B1088 [GND-SHORT] PRE-TEN FRONT LH

For front LH seat belt pre-tensioner, crash is judged by main “G” sensor output signal and Safing algorithm in
front direction.

OPERATION

STRUCTURE

The restraint system for front seat occupant consists of the pre-tensioner mechanism and load limiter mecha-
nism.

INSTALLATION

Front LH seat belt pre-tensioner is installed on the underside of center pillar with fixed nuts.

DTC Logic

INFOID:0000000003367416

DTC DETECTION LOGIC

With CONSULT-lll

DTC No. Index (“SELF-DIAG [CURRENT]”), (“SELF-DIAG [PAST]” or “TROUBLE DIAG RECORD”)

DTC CONFIRMATION PROCEDURE (With CONSULT-lll)

INSPECTION START

Turn ignition switch ON.

>> GO TO 2.

CHECK SELF-DIAG RESULT

Check the screen of CONSULT-lll.

Is malfunctioning part detected?

YES

>> Refer to

SRC-87, "Diagnosis Procedure"

>> INSPECTION END.

DTC CONFIRMATION PROCEDURE (Without CONSULT-lll)

NOTE:
• SRS will not enter diagnosis mode if no malfunction is detected in user mode.

INSPECTION START

Turn ignition switch ON.

DTC No.

Trouble diagnosis name

DTC detecting condition

Possible cause

B1088

PRE-TEN FRONT LH
[GND-SHORT]

Front LH seat belt pre-tensioner circuit
is shorted to ground

• Disconnection of wiring harness and

short

• Internal breakdown in front LH seat

belt pre-tensioner

• Internal breakdown in air bag diag-

nosis sensor unit

Revision: 2008 October

2009 Murano

B1088 PRE-TEN FRONT LH

SRC-87

< COMPONENT DIAGNOSIS >

[FOR USA AND CANADA]

SRC

>> GO TO 2.

CHECK AIR BAG WARNING LAMP

Check the air bag warning lamp status.

Is malfunctioning part detected?

YES

>> Refer to warning lamp flash code chart.

SRC-142

>> INSPECTION END.

Diagnosis Procedure

INFOID:0000000003367417

With CONSULT-lll

WARNING:

• Before servicing, turn ignition switch OFF, disconnect battery negative terminal and wait at least 3

minutes. (To discharge backup capacitor.)

• Do not use unspecified tester or other measuring device.

DIAGNOSTIC PROCEDURE

CHECK HARNESS CONNECTOR

Check the connection of harness connector.
Is the inspection result normal?

YES

>> GO TO 2.

>> Repair or replace harness connector.

CHECK WIRING HARNESS

Check the wiring harness externals.
Is the inspection result normal?

YES

>> GO TO 3.

>> Repair or replace wiring harness.

CHECK FRONT SEAT BELT PRE-TENSIONER

Replace front LH seat belt pre-tensioner.

Check the screen of CONSULT-lll.

Is the inspection result normal?

YES

>> INSPECTION END.

>> Check the intermittent incident. Refer to

GI-40, "Intermittent Incident"

Revision: 2008 October

2009 Murano

SRC-88

< COMPONENT DIAGNOSIS >

[FOR USA AND CANADA]

B1089 PRE-TEN FRONT LH

B1089 PRE-TEN FRONT LH

Description

INFOID:0000000003367418

DTC B1089 [SHORT] PRE-TEN FRONT LH

For front LH seat belt pre-tensioner, crash is judged by main “G” sensor output signal and Safing algorithm in
front direction.

OPERATION

STRUCTURE

The restraint system for front seat occupant consists of the pre-tensioner mechanism and load limiter mecha-
nism.

INSTALLATION

Front LH seat belt pre-tensioner is installed on the underside of center pillar with fixed nuts.

DTC Logic

INFOID:0000000003367419

DTC DETECTION LOGIC

With CONSULT-lll

DTC No. Index (“SELF-DIAG [CURRENT]”), (“SELF-DIAG [PAST]” or “TROUBLE DIAG RECORD”)

DTC CONFIRMATION PROCEDURE (With CONSULT-lll)

INSPECTION START

Turn ignition switch ON.

>> GO TO 2.

CHECK SELF-DIAG RESULT

Check the screen of CONSULT-lll.

Is malfunctioning part detected?

YES

>> Refer to

SRC-89, "Diagnosis Procedure"

>> INSPECTION END.

DTC CONFIRMATION PROCEDURE (Without CONSULT-lll)

NOTE:
• SRS will not enter diagnosis mode if no malfunction is detected in user mode.

INSPECTION START

Turn ignition switch ON.

DTC No.

Trouble diagnosis name

DTC detecting condition

Possible cause

B1089

PRE-TEN FRONT LH
[SHORT]

Front LH seat belt pre-tensioner circuit
are shorted to each other

• Disconnection of wiring harness and

short

• Internal breakdown in front LH seat

belt pre-tensioner

• Internal breakdown in air bag diag-

nosis sensor unit

Revision: 2008 October

2009 Murano

B1089 PRE-TEN FRONT LH

SRC-89

< COMPONENT DIAGNOSIS >

[FOR USA AND CANADA]

SRC

>> GO TO 2.

CHECK AIR BAG WARNING LAMP

Check the air bag warning lamp status.

Is malfunctioning part detected?

YES

>> Refer to warning lamp flash code chart.

SRC-142

>> INSPECTION END.

Diagnosis Procedure

INFOID:0000000003367420

With CONSULT-lll

WARNING:

• Before servicing, turn ignition switch OFF, disconnect battery negative terminal and wait at least 3

minutes. (To discharge backup capacitor.)

• Do not use unspecified tester or other measuring device.

DIAGNOSTIC PROCEDURE

CHECK HARNESS CONNECTOR

Check the connection of harness connector.
Is the inspection result normal?

YES

>> GO TO 2.

>> Repair or replace harness connector.

CHECK WIRING HARNESS

Check the wiring harness externals.
Is the inspection result normal?

YES

>> GO TO 3.

>> Repair or replace wiring harness.

CHECK FRONT SEAT BELT PRE-TENSIONER

Replace front LH seat belt pre-tensioner.

Check the screen of CONSULT-lll.

Is the inspection result normal?

YES

>> INSPECTION END.

>> Check the intermittent incident. Refer to

GI-40, "Intermittent Incident"

Revision: 2008 October

2009 Murano

SRC-90

< COMPONENT DIAGNOSIS >

[FOR USA AND CANADA]

B1090, B1091, B1092, B1093 DIAGNOSIS SENSOR UNIT

B1090, B1091, B1092, B1093 DIAGNOSIS SENSOR UNIT

Description

INFOID:0000000004185374

Checks the entire SRS and displays the malfunction either by illuminating or blinking the air bag warning lamp
on the combination meter. Malfunctioning part can be detected by on board self-diagnosis system and CON-
SULT-III.

OPERATION

It detects a shock that exceeds a specified level and monitors whether the driver and passenger air bags, front
side air bag, side curtain air bag and pre-tensioner seat belts operate normally.

STRUCTURE

It contains the “G” sensors for both frontal and side collisions and spare battery function in case of main bat-
tery damage in collision.

INSTALLATION

Air bag diagnosis sensor unit is installed under the center console with fixed bolts.

DTC Logic

INFOID:0000000004185375

DTC CONFIRMATION PROCEDURE

CHECK SELF-DIAG RESULT

With CONSULT-III

Turn ignition switch ON.

Perform “AIR BAG” Self Diagnostic Result.

Without CONSULT-III

Turn ignition switch ON.

Check the air bag warning lamp status. Refer to

SRC-18, "Diagnosis Description"

NOTE:
SRS does not enter diagnosis mode if no malfunction is detected in user mode.

Is malfunctioning part detected?

YES

>> Refer to

SRC-90, "Diagnosis Procedure"

>> INSPECTION END

Diagnosis Procedure

INFOID:0000000004185376

WARNING:

• Before servicing, turn ignition switch OFF, disconnect battery negative terminal and wait at least 3

minutes. (To discharge backup capacitor.)

• Never use unspecified tester or other measuring device.

CHECK HARNESS CONNECTOR

Check the harness connector.

Is the inspection result normal?

YES

>> GO TO 2.

>> Replace harness connectors.

CHECK WIRING HARNESS

Check the wiring harness externals.

Is the inspection result normal?

YES

>> GO TO 3.

DTC No.

Trouble diagnosis name

DTC detecting condition

Possible cause

B1090
B1091
B1092
B1093

CONTROL UNIT

Air bag diagnosis sensor unit is mal-
functioning or out of the specification

• Malfunction in air bag diagnosis sen-

sor unit

• Configuration in air bag diagnosis

sensor unit does not match the vehi-
cles specification

Revision: 2008 October

2009 Murano

B1090, B1091, B1092, B1093 DIAGNOSIS SENSOR UNIT

SRC-91

< COMPONENT DIAGNOSIS >

[FOR USA AND CANADA]

SRC

>> Replace wiring harness.

REPLACE AIR BAG DIAGNOSIS SENSOR UNIT

Replace air bag diagnosis sensor unit. Refer to

SR-19, "Exploded View"

Perform DTC confirmation procedure. Refer to

SRC-90, "DTC Logic"

Is DTC detected?

YES

>> GO TO 1.

>> INSPECTION END

Revision: 2008 October

2009 Murano

SRC-92

< COMPONENT DIAGNOSIS >

[FOR USA AND CANADA]

B1106, B1107, B1108, B1109, B1110, B1111 DIAGNOSIS SENSOR UNIT

B1106, B1107, B1108, B1109, B1110, B1111 DIAGNOSIS SENSOR UNIT

Description

INFOID:0000000003367421

DTC B1106, B1107, B1108, B1109, B1110, B1111 DIAGNOSIS SENSOR UNIT

Detects the whole SRS electrical system and displays the malfunction either by illuminating or blinking the air
bag warning lamp in the combination meter. Malfunctioning part can be detected by on board self-diagnosis
system and electro-diagnosis tester CONSULT-III.

OPERATION

It detects a shock that exceeds specified level and monitors such systems as the driver and passenger air
bag, side air bag, curtain air bag, pre-tensioner seat belts and Occupant Classification System (OCS) operate
properly.

STRUCTURE

It contains the “G” sensors for both frontal and side collisions and spare battery function in case of main bat-
tery damage in collision.

INSTALLATION

Air bag diagnosis sensor unit is installed under the center console with fixed bolts.

DTC Logic

INFOID:0000000003367422

DTC DETECTION LOGIC

With CONSULT-III

DTC No. Index (“SELF-DIAG [CURRENT]”), (“SELF-DIAG [PAST]” or “TROUBLE DIAG RECORD”)

DTC CONFIRMATION PROCEDURE (With CONSULT-III)

INSPECTION START

Turn ignition switch ON.

>> GO TO 2.

CHECK SELF-DIAG RESULT

Check the screen of CONSULT-III.
Is malfunctioning part detected?

YES

>> Refer to

SRC-93, "Diagnosis Procedure"

>> INSPECTION END.

DTC CONFIRMATION PROCEDURE (Without CONSULT-III)

NOTE:
• SRS will not enter diagnosis mode if no malfunction is detected in user mode.

INSPECTION START

Turn ignition switch ON.

DTC No.

Trouble diagnosis name

DTC detecting condition

Possible cause

B1106
B1107
B1108
B1109

B1110

B1111

CONTROL UNIT

Air bag diagnosis sensor unit is out of
order or mis-match

• Internal breakdown in air bag diag-

nosis sensor unit

• Mis-match between specification on

vehicle and configuration in air bag
diagnosis sensor unit

Revision: 2008 October

2009 Murano

B1106, B1107, B1108, B1109, B1110, B1111 DIAGNOSIS SENSOR UNIT

SRC-93

< COMPONENT DIAGNOSIS >

[FOR USA AND CANADA]

SRC

>> GO TO 2.

CHECK AIR BAG WARNING LAMP

Check the air bag warning lamp status.

Is malfunctioning part detected?

YES

>> Refer to warning lamp flash code chart.

SRC-142

>> INSPECTION END.

Diagnosis Procedure

INFOID:0000000003367423

With CONSULT-III

WARNING:

• Before servicing, turn ignition switch OFF, disconnect battery negative terminal and wait at least 3

minutes. (To discharge backup capacitor.)

• Do not use unspecified tester or other measuring device.

DIAGNOSTIC PROCEDURE

CHECK HARNESS CONNECTOR

Check the connection of harness connector.

Is the inspection result normal?

YES

>> GO TO 2.

>> Repair or replace harness connectors.

CHECK WIRING HARNESS

Check the wiring harness externals.

Is the inspection result normal?

YES

>> GO TO 3.

>> Repair or replace wiring harness.

CHECK AIR BAG DIAGNOSIS SENSOR UNIT

Replace air bag diagnosis sensor unit.

Check the screen of CONSULT-III.

Is the inspection result normal?

YES

>> INSPECTION END.

>> Check the intermittent incident. Refer to

GI-40, "Intermittent Incident"

Revision: 2008 October

2009 Murano

SRC-94

< COMPONENT DIAGNOSIS >

[FOR USA AND CANADA]

B1113, B1114 SATELLITE SENS RH

B1113, B1114 SATELLITE SENS RH

Description

INFOID:0000000003367424

DTC B1113, B1114 [UNIT FAIL] SATELLITE SENS RH

Main “G” sensor generates signal voltage, when it detects deceleration beyond the specified level by vehicle
side collision.

OPERATION

When air bag diagnosis sensor unit define the both signal voltage of the “G” sensor and the Safing algorithm to
be that of collision which exceeds specified level, the driving circuit switches on and feeds the electric ignitor of
both the side air bag and curtain air bag.

STRUCTURE

Integrated type of the “G” sensor element for side collision with output terminals for signal voltage.

INSTALLATION

RH satellite sensor is installed at the underside of center pillar with fixed nuts.

DTC Logic

INFOID:0000000003367425

DTC DETECTION LOGIC

With CONSULT-lll

DTC No. Index (“SELF-DIAG [CURRENT]”), (“SELF-DIAG [PAST]” or “TROUBLE DIAG RECORD”)

DTC CONFIRMATION PROCEDURE (With CONSULT-lll)

INSPECTION START

Turn ignition switch ON.

>> GO TO 2.

CHECK SELF-DIAG RESULT

Check the screen of CONSULT-lll.

Is malfunctioning part detected?

YES

>> Refer to

SRC-95, "Diagnosis Procedure"

>> INSPECTION END.

DTC CONFIRMATION PROCEDURE (Without CONSULT-lll)

NOTE:
• SRS will not enter diagnosis mode if no malfunction is detected in user mode.

INSPECTION START

Turn ignition switch ON.

>> GO TO 2.

DTC No.

Trouble diagnosis name

DTC detecting condition

Possible cause

B1113
B1114

SATELLITE SENS RH
[UNIT FAIL]

RH satellite sensor is out of order

• Disconnection of wiring harness
• Internal breakdown in RH satellite

sensor

• Internal breakdown in air bag diag-

nosis sensor unit

Revision: 2008 October

2009 Murano

B1113, B1114 SATELLITE SENS RH

SRC-95

< COMPONENT DIAGNOSIS >

[FOR USA AND CANADA]

SRC

CHECK AIR BAG WARNING LAMP

Check the air bag warning lamp status.
Is malfunctioning part detected?

YES

>> Refer to warning lamp flash code chart.

SRC-142

>> INSPECTION END.

Diagnosis Procedure

INFOID:0000000003367426

With CONSULT-lll

WARNING:

• Before servicing, turn ignition switch OFF, disconnect battery negative terminal and wait at least 3

minutes. (To discharge backup capacitor.)

• Do not use unspecified tester or other measuring device.

DIAGNOSTIC PROCEDURE

CHECK HARNESS CONNECTOR

Check the connection of harness connector.

Is the inspection result normal?

YES

>> GO TO 2.

>> Repair or replace harness connector.

CHECK WIRING HARNESS

Check the wiring harness externals.

Is the inspection result normal?

YES

>> GO TO 3.

>> Repair or replace wiring harness.

CHECK SATELLITE SENSOR

Replace RH satellite sensor.

Check the screen of CONSULT-lll.

Is the inspection result normal?

YES

>> INSPECTION END.

>> Check the intermittent incident. Refer to

GI-40, "Intermittent Incident"

Revision: 2008 October

2009 Murano

Nissan Murano Z51 (2008 year). Manual - part 354