Nissan Murano Z51 (2008 year). Manual

SE-110

< ON-VEHICLE REPAIR >

FRONT SEAT

• Remove the side air bag module harness (A) and disconnect

the seat cushion heater harness connector (B).

Remove the seatback assembly.
• Remove the seatback mounting bolts (A), and then remove

the seatback assembly.

Remove the seat cushion front finisher. (Power seat only)
• Remove the seat cushion front finisher mounting screws (A).
• Remove the seat cushion front finisher mounting pawl.

Remove the seat cushion outer finisher outside.

Power seat
• Remove the seat control switch knob and reclining switch knob and lumbar support switch.
• Remove the seat cushion outer finisher mounting screw (A),

metal clips and pawls.

• Disconnect the seat control switch, reclining switch and lum-

bar support switch harness connectors (Driver's seat only).

Manual seat

JMJIA1426ZZ

JMJIA1427ZZ

: Pawl

JMJIA1428ZZ

: Metal clip

: Pawl

JMJIA1429ZZ

Revision: 2008 October

2009 Murano

FRONT SEAT

SE-111

< ON-VEHICLE REPAIR >

• Remove the pawls, and then lifter lever knob finisher (1).

(Driver's manual seat only)

• Remove the mounting screws, and remove the lifter lever (2).

(Driver's manual seat only)

• Pull out the reclining lever while holding and raising the pawl.

• Remove the mounting screws (A).
• Remove the metal clip and pawls, and then pull out seat cush-

ion outer finisher outside.

Remove the seat cushion outer finisher inside (left).
• Remove the mounting screw (A).

: Pawl

JMJIA1090ZZ

: Pawl

JMJIA1091ZZ

:Metal clip

: Pawl

JMJIA1482ZZ

JMJIA1430ZZ

Revision: 2008 October

2009 Murano

SE-112

< ON-VEHICLE REPAIR >

FRONT SEAT

Remove the seat slide outer cover (Driver's seat only) mounting
screws (A), and then slide to backward.

Remove the mounting screw (A) and pawls, and then pull out
seat cushion inner finisher outer.

Remove the mounting screw (A), and then pull out seat cushion
inner finisher inside (right).

10. Remove the mounting screws (A), and then pull out seat slide

inner cover. (Driver's seat only)

11. Remove the seat cushion trim and seat cushion pad. (Without occupant classification system control unit

model)
• Remove the seat cushion trim retainer.
• Remove the seat cushion trim and seat cushion pad from the seat cushion frame.
• Remove the hog rings, and separate the seat cushion trim and seat cushion pad.

12. Remove the seat belt buckle.

SB-7, "SEAT BELT BUCKLE : Exploded View"

13. Remove the driver seat control unit.

ADP-204, "Exploded View"

Assembly

Assemble in the reverse order of disassembly.

JMJIA1431ZZ

: Pawl

JMJIA1432ZZ

JMJIA1433ZZ

JMJIA1469ZZ

Revision: 2008 October

2009 Murano

FRONT SEAT

SE-113

< ON-VEHICLE REPAIR >

CAUTION:

Install the hog rings of seat cushion trim in position, and then securely connect the trim or trim cord
with the pad side wire.

Revision: 2008 October

2009 Murano

SE-114

< ON-VEHICLE REPAIR >

REAR SEAT

REAR SEAT

Exploded View

INFOID:0000000003396993

REAR SEAT (LH SIDE)

Headrest (LH)

Headrest holder (locked)

Headrest holder (free)

Seatback trim

Seatback pad

Reclining device inner cover (out-
side)

Reclining device inner cover (inside) 8.

Seat cushion trim

Seat cushion hinge cover

10. Seat cushion link cover

11.

Seat cushion pad and frame

12. Seat cushion link bush

13. Reclining device outer cover

14. Reclining cover

15. Rear seat harness (LH)

JMJIA1466GB

Revision: 2008 October

2009 Murano

REAR SEAT

SE-115

< ON-VEHICLE REPAIR >

REAR SEAT (RH SIDE)

16. Reclining device assembly

17. Seatback control cable

18. Seatback control lever escutcheon

19. Seatback frame

20. Seatback board

21. Seatback board clip

22. Seatback silencer

Refer to

GI-4, "Components"

for symbols in the figure.

Headrest (RH)

Headrest (center)

Headrest holder (locked)

Headrest holder (free)

Seatback trim

Seatback pad

Armrest inner cover

Cup holder

Armrest

10. Armrest bush

11.

Armrest outer cover

12. Seat cushion trim

13. Seat cushion hinge cover

14. Seat cushion link cover

15. Seat cushion pad and frame

JMJIA1465GB

Revision: 2008 October

2009 Murano

SE-116

< ON-VEHICLE REPAIR >

REAR SEAT

Removal and Installation

INFOID:0000000003396994

REMOVAL

CAUTION:

When removing and installing, use shop cloths to protect parts from damage.

Remove the seat mounting bolts and nuts.
• Pull up the luggage floor finisher front (1).
• Remove the seat mounting bolt (A) and nut (B).

Disconnect the rear seat harness connector (A) and heater unit harness connector (B). (Power return seat
and heater seat model only)

LH side

RH side

Remove the reclining cover.

16. Seat cushion link bush

17. Reclining device inner cover (out-

side)

18. Reclining device inner cover (inside)

19. Reclining device assembly

20. Reclining device outer cover

21. Reclining cover

22. Rear seat harness (RH)

23. Seatback board

24. Seatback board clip

25. Seatback frame

26. Dynamic dumper

27. Seatback control lever escutcheon

28. Seatback control cable

29. Seatback silencer

Refer to

GI-4, "Components"

for symbols in the figure.

JMJIA1476ZZ

JMJIA1477ZZ

JMJIA1478ZZ

Revision: 2008 October

2009 Murano

REAR SEAT

SE-117

< ON-VEHICLE REPAIR >

Remove the seatback control cable (1) from reclining device
assembly and seat mounting bolt (A).

Remove the seat cushion hinge cover.

Remove the rear seat mounting bolts (A).

Pull up the seat cushion and remove the seat mounting bolt (A).

Remove the rear seat assembly from back door.

INSTALLATION

NOTE:
Tighten rear seat mouniting bolts and nuts following the numerical order shown in the figure.
1.

Install the rear seat mounting bolt on behind the seatback (out
side) and nut on behind the seatback (inside).

Install the rear seat mounting bolt on the seat cushion out side.

Connect the rear seat harness connector and heater harness connector. (Power return seat and heater
seat only)

JMJIA1479ZZ

JMJIA1480ZZ

JMJIA1481ZZ

JMJIA1683ZZ

Revision: 2008 October

2009 Murano

SE-118

< ON-VEHICLE REPAIR >

REAR SEAT

Install the rear seat mounting bolt on the reclining device exten-
sion bracket.

Install the rear seat mounting bolt and on the seat cushion
hinge.

Connect the seatback control cable.

Install the seat cushion hinge cover.

Install the reclining cover.

CAUTION:

• When removing and installing, use shop cloths to protect parts from damage.
• When removing and installing, 2 workers are required so as to prevent it from dropping.
• Before installation, check that the rear seat harness and seatback control cable is not pressed by

seat frame.

Disassembly and Assembly

INFOID:0000000003396995

SEATBACK

Disassembly

Remove the armrest. (RH seat only)
• Remove the armrest outer cover.

JMJIA1684ZZ

JMJIA1685ZZ

: Pawl

JMJIA1470ZZ

Revision: 2008 October

2009 Murano

REAR SEAT

SE-119

< ON-VEHICLE REPAIR >

• Remove the armrest mounting bolts (A), and then slide the

armrest to toward the arrow direction.

Separate the seatback assembly and seat cushion assembly.
• Disconnect the seat cushion heater unit harness connectors

(A) and remove the harness clamps. (with heater seat model
only)

• Remove the seat cushion link cover.

• Remove the mounting bolt (A), and then separate the seat-

back assembly and seat cushion assembly.

JMJIA1471ZZ

JMJIA1438ZZ

JMJIA1439ZZ

JMJIA1440ZZ

Revision: 2008 October

2009 Murano

SE-120

< ON-VEHICLE REPAIR >

REAR SEAT

Remove the mounting screw (A), and then remove the reclining
device outer cover.

Remove the mounting screws (A), and then remove the reclining
device inner cover (outside). (LH seat)

Remove the seatback trim and pad.
• Remove the clips, and then pull out the seatback board.

• Remove the seatback trim fixing hog rings and retainer.
• Remove the headrest holder.

CAUTION:

Before installing headrest holder check its orientation.
(front/rear and right/left)

• Remove the seatback trim and pad from seatback frame.
• Remove the hog rings to separate the seatback trim and seat-

back pad.

Remove the seatback silencer.

JMJIA1441ZZ

JMJIA1442ZZ

: Clip

JMJIA1443ZZ

PIIB4084J

Revision: 2008 October

2009 Murano

REAR SEAT

SE-121

< ON-VEHICLE REPAIR >

Remove the screws (A), and then remove the reclining device
inner cover (outside). (RH seat)

Remove the screw (A), and then remove the reclining device
inner cover (inside).

Remove the mounting bolts (A), and then remove the seatback
frame from reclining device assembly.

10. Remove the mounting nuts (A), and then remove the dynamic

dumper. (With top road sunroof model only)

Assembly

Assemble in the reverse order of disassembly.

CAUTION:

Install the hog rings of seatback trim in position, and then securely connect the trim or trim cord with
the seatback frame.

SEAT CUSHION

Disassembly

Remove the armrest. (RH seat only)

JMJIA1444ZZ

JMJIA1445ZZ

JMJIA1446ZZ

JMJIA1447ZZ

Revision: 2008 October

2009 Murano

SE-122

< ON-VEHICLE REPAIR >

REAR SEAT

• Remove the pawl, and then pull out armrest outer cover.

• Remove the mounting bolts (A), and then slide the armrest to

outside.

Separate the seatback assembly and seat cushion assembly.
• Disconnect the seat cushion heater unit harness connectors

(A) and remove the harness clamps. (with heater seat model
only)

• Remove the seat cushion link cover.

: Pawl

JMJIA1470ZZ

JMJIA1471ZZ

JMJIA1438ZZ

JMJIA1439ZZ

Revision: 2008 October

2009 Murano

REAR SEAT

SE-123

< ON-VEHICLE REPAIR >

• Remove the mounting bolt (A), and then separate the seat-

back assembly and seat cushion assembly.

Remove the seat cushion trim.
Remove the seat cushion trim fixing retainers and hog rings, and then remove the seat cushion trim from
seat cushion pad and frame.

Assembly

Assemble in the reverse order of disassembly.

CAUTION:

Install the hog rings of seat cushion trim in position, and then securely connect the trim or trim cord
with the seat cushion pad wire.

JMJIA1440ZZ

Revision: 2008 October

2009 Murano

SE-124

< ON-VEHICLE REPAIR >

SEATBACK CONTROL CABLE

SEATBACK CONTROL CABLE

Exploded View

INFOID:0000000003639920

REAR SEAT (LH SIDE)

Headrest (LH)

Headrest holder (locked)

Headrest holder (free)

Seatback trim

Seatback pad

Reclining device inner cover (out-
side)

Reclining device inner cover (inside) 8.

Seat cushion trim

Seat cushion hinge cover

10. Seat cushion link cover

11.

Seat cushion pad and frame

12. Seat cushion link bush

13. Reclining device outer cover

14. Reclining cover

15. Rear seat harness (LH)

JMJIA1466GB

Revision: 2008 October

2009 Murano

SEATBACK CONTROL CABLE

SE-125

< ON-VEHICLE REPAIR >

REAR SEAT (RH SIDE)

16. Reclining device assembly

17. Seatback control cable

18. Seatback control lever escutcheon

19. Seatback frame

20. Seatback board

21. Seatback board clip

22. Seatback silencer

Refer to

GI-4, "Components"

for symbols in the figure.

Headrest (RH)

Headrest (center)

Headrest holder (locked)

Headrest holder (free)

Seatback trim

Seatback pad

Armrest inner cover

Cup holder

Armrest

10. Armrest bush

11.

Armrest outer cover

12. Seat cushion trim

13. Seat cushion hinge cover

14. Seat cushion link cover

15. Seat cushion pad and frame

JMJIA1465GB

Revision: 2008 October

2009 Murano

Nissan Murano Z51 (2008 year). Manual - part 317