Nissan Murano Z51 (2008 year). Manual - part 265

MIR-56

< SYMPTOM DIAGNOSIS >

[WITH ADP]

SQUEAK AND RATTLE TROUBLE DIAGNOSES

Diagnostic Worksheet

INFOID:0000000004757248

PIIB8740E

Revision: 2008 October

2009 Murano

SQUEAK AND RATTLE TROUBLE DIAGNOSES

MIR-57

< SYMPTOM DIAGNOSIS >

[WITH ADP]

C

D

E

F

G

H

I

J

K

M

A

B

MIR

N

O

P

PIIB8742E

Revision: 2008 October

2009 Murano

MIR-58

< PRECAUTION >

[WITH ADP]

PRECAUTIONS

PRECAUTION

PRECAUTIONS

Precaution for Supplemental Restraint System (SRS) "AIR BAG" and "SEAT BELT 
PRE-TENSIONER"

INFOID:0000000004778631

The Supplemental Restraint System such as “AIR BAG” and “SEAT BELT PRE-TENSIONER”, used along
with a front seat belt, helps to reduce the risk or severity of injury to the driver and front passenger for certain
types of collision. This system includes seat belt switch inputs and dual stage front air bag modules. The SRS
system uses the seat belt switches to determine the front air bag deployment, and may only deploy one front
air bag, depending on the severity of a collision and whether the front occupants are belted or unbelted.
Information necessary to service the system safely is included in the “SRS AIRBAG” and “SEAT BELT” of this
Service Manual.

WARNING:

• To avoid rendering the SRS inoperative, which could increase the risk of personal injury or death in

the event of a collision which would result in air bag inflation, all maintenance must be performed by
an authorized NISSAN/INFINITI dealer.

• Improper maintenance, including incorrect removal and installation of the SRS, can lead to personal

injury caused by unintentional activation of the system. For removal of Spiral Cable and Air Bag
Module, see the “SRS AIRBAG”.

• Never use electrical test equipment on any circuit related to the SRS unless instructed to in this Ser-

vice Manual. SRS wiring harnesses can be identified by yellow and/or orange harnesses or harness
connectors.

PRECAUTIONS WHEN USING POWER TOOLS (AIR OR ELECTRIC) AND HAMMERS

When working near the Airbag Diagnosis Sensor Unit or other Airbag System sensors while ignition switch is
ON or engine is running, never use air or electric power tools or strike near the sensor(s) with a hammer.
Heavy vibration may activate the sensor(s), deploy the airbag(s), possibly cause serious injury.
When using air or electric power tools or hammers, always turn OFF ignition switch, disconnect the battery,
and wait 3 minutes or more before performing any service.

Precaution Necessary for Steering Wheel Rotation after Battery Disconnect

INFOID:0000000004778632

NOTE:
• Before removing and installing any control units, first turn the push-button ignition switch to the LOCK posi-

tion, then disconnect both battery cables.

• After finishing work, confirm that all control unit connectors are connected properly, then re-connect both

battery cables.

• Always use CONSULT-III to perform self-diagnosis as a part of each function inspection after finishing work.

If a DTC is detected, perform trouble diagnosis according to self-diagnosis results.

This vehicle is equipped with a push-button ignition switch and a steering lock unit.
If the battery is disconnected or discharged, the steering wheel will lock and cannot be turned.
If turning the steering wheel is required with the battery disconnected or discharged, follow the procedure
below before starting the repair operation.

OPERATION PROCEDURE

1.

Connect both battery cables.
NOTE:
Supply power using jumper cables if battery is discharged.

2.

Turn the push-button ignition switch to ACC position.
(At this time, the steering lock will be released.)

3.

Disconnect both battery cables. The steering lock will remain released with both battery cables discon-
nected and the steering wheel can be turned.

4.

Perform the necessary repair operation.

5.

When the repair work is completed, re-connect both battery cables. With the brake pedal released, turn
the push-button ignition switch from ACC position to ON position, then to LOCK position. (The steering
wheel will lock when the push-button ignition switch is turned to LOCK position.)

6.

Perform self-diagnosis check of all control units using CONSULT-III.

Revision: 2008 October

2009 Murano

PRECAUTIONS

MIR-59

< PRECAUTION >

[WITH ADP]

C

D

E

F

G

H

I

J

K

M

A

B

MIR

N

O

P

Precaution for Procedure without Cowl Top Cover

INFOID:0000000004778633

When performing the procedure after removing cowl top cover, cover
the lower end of windshield with urethane, etc.

Precaution for Work

INFOID:0000000003544507

• After removing and installing the opening/closing parts, be sure to carry out fitting adjustments to check their

operation.

• Check the lubrication level, damage, and wear of each part. If necessary, grease or replace it.

PIIB3706J

Revision: 2008 October

2009 Murano

MIR-60

< PREPARATION >

[WITH ADP]

PREPARATION

PREPARATION

PREPARATION

Special Service Tools

INFOID:0000000004757253

The actual shapes of Kent-Moore tools may differ from those of special service tools illustrated here.

Commercial Service Tools

INFOID:0000000004757254

Tool number

(Kent-Moore No.)

Tool name

Description

(J-39570)
Chassis ear

Locates the noise

(J-43980)
NISSAN Squeak and Rat-
tle Kit

Repairs the cause of noise

SIIA0993E

SIIA0994E

Tool name

Description

Engine ear

Locates the noise

Remover tool

Removes the clips, pawls, and metal clips

Power tool

SIIA0995E

JMKIA3050ZZ

PIIB1407E

Revision: 2008 October

2009 Murano

INSIDE MIRROR

MIR-61

< ON-VEHICLE REPAIR >

[WITH ADP]

C

D

E

F

G

H

I

J

K

M

A

B

MIR

N

O

P

ON-VEHICLE REPAIR

INSIDE MIRROR

Exploded View

INFOID:0000000003459056

Removal and Installation

INFOID:0000000003459057

CAUTION:

Never reuse the inside mirror disassembled from mirror base.

REMOVAL

1.

Remove the inside mirror cover.

2.

Remove TORX bolt.

3.

Slide the inside mirror upward to remove.

INSTALLATION

Install in the reverse order of removal.

CAUTION:

When inserting the inside mirror into the mirror base, be sure to push the pawl until it get connected to
the mirror base.

1.

Inside mirror

2.

Inside mirror cover

3.

Mirror base

4.

TORX bolt

Refer to 

GI-4, "Components"

 for symbols in the figure.

JMLIA0136GB

Revision: 2008 October

2009 Murano

MIR-62

< ON-VEHICLE REPAIR >

[WITH ADP]

OUTSIDE MIRROR

OUTSIDE MIRROR

DOOR MIRROR ASSEMBLY

DOOR MIRROR ASSEMBLY : Exploded View

INFOID:0000000003459058

REMOVAL

DISASSEMBLY

1.

Door mirror assembly

2.

Front door assembly

3.

Door mirror corner cover

: Clip

JMLIA0122ZZ

JMLIA0123ZZ

Revision: 2008 October

2009 Murano

OUTSIDE MIRROR

MIR-63

< ON-VEHICLE REPAIR >

[WITH ADP]

C

D

E

F

G

H

I

J

K

M

A

B

MIR

N

O

P

DOOR MIRROR ASSEMBLY : Removal and Installation

INFOID:0000000003459059

CAUTION:

Never damage the mirror bodies.

REMOVAL

1.

Remove the front door finisher. Refer to 

INT-11, "FRONT DOOR FINISHER : Removal and Installation"

.

2.

Remove the door mirror corner cover.

3.

Disconnect the door mirror harness connector.

4.

Remove the door mirror mounting nuts, and remove the door mirror assembly.

INSTALLATION

Install in the reverse order of removal.

GLASS MIRROR

GLASS MIRROR : Exploded View

INFOID:0000000003459060

GLASS MIRROR : Disassembly and Assembly

INFOID:0000000003459061

CAUTION:

Never damage the mirror bodies.

DISASSEMBLY

1.

Door mirror cover

2.

Door mirror assembly

3.

Glass mirror

: Pawl

1.

Door mirror cover

2.

Door mirror assembly

3.

Glass mirror

: Pawl

JMLIA0123ZZ

Revision: 2008 October

2009 Murano

MIR-64

< ON-VEHICLE REPAIR >

[WITH ADP]

OUTSIDE MIRROR

1.

Place the glass mirror upward.

2.

Put a strip of protective tape (A) on the housing.

3.

Insert flat-bladed screwdriver (B) into the recess at lower side
between glass mirror (1) and actuator (2), and push up pawls to
remove glass mirror lower side.
NOTE:
 Insert a small slotted screwdriver into recess, and push up while
rotating (twist) to make work easier.

4.

Insert flat-bladed screwdriver at RH/LH side between glass mirror and actuator, and push up pawls to
remove glass mirror RH/LH side.
NOTE:
 Insert flat-bladed screwdriver into recesses, and push up while rotating (twist) to make work easier.

5.

Remove two terminals of mirror heater attachment. (With heater mirror model)

6.

Pull glass mirror as shown in the figure in order to disengage
both upper pawls, and then remove glass mirror.

ASSEMBLY

Install in the reverse order of removal.

CAUTION:

After installation, visually check that pawls are securely engaged.

DOOR MIRROR COVER

JMLIA0124ZZ

1.

Glass mirror

2.

Actuator

JMLIA0092ZZ

Revision: 2008 October

2009 Murano

OUTSIDE MIRROR

MIR-65

< ON-VEHICLE REPAIR >

[WITH ADP]

C

D

E

F

G

H

I

J

K

M

A

B

MIR

N

O

P

DOOR MIRROR COVER : Exploded View

INFOID:0000000003459066

DOOR MIRROR COVER : Disassembly and Assembly

INFOID:0000000003459063

CAUTION:

Never damage the mirror bodies.

DISASSEMBLY

1.

Remove the glass mirror. Refer to 

MIR-63, "GLASS MIRROR : Disassembly and Assembly"

.

2.

Remove the pawls, and disassemble the door mirror cover from the mirror assembly.

ASSEMBLY

Install in the reverse order of removal.
NOTE:
After installation, visually check that pawls are securely engaged.

1.

Door mirror cover

2.

Door mirror assembly

3.

Glass mirror

: Pawl

JMLIA0123ZZ

Revision: 2008 October

2009 Murano

MIR-66

< ON-VEHICLE REPAIR >

[WITH ADP]

DOOR MIRROR REMOTE CONTROL SWITCH

DOOR MIRROR REMOTE CONTROL SWITCH

Exploded View

INFOID:0000000003554756

Refer to 

INT-11, "FRONT DOOR FINISHER : Exploded View"

Removal and Installation

INFOID:0000000003554757

REMOVAL

1.

Remove the power window main switch finisher (2). Refer to

PWC-114, "Removal and Installation"

2.

Remove door mirror remote control switch (1) from power win-
dow main switch finisher (2) using flat-bladed screwdriver (A).

INSTALLATION

Install in the reverse order of removal.

: Pawl

JMLIA0118ZZ

Revision: 2008 October

2009 Murano

DOOR MIRROR SYSTEM

MIR-67

< FUNCTION DIAGNOSIS >

[WITHOUT ADP]

C

D

E

F

G

H

I

J

K

M

A

B

MIR

N

O

P

FUNCTION DIAGNOSIS

DOOR MIRROR SYSTEM

Component Description

INFOID:0000000003554782

Component

Function

Door mirror remote control switch

It supplies power to mirror motor through mirror switch and changeover 
switch.

Door mirror

It makes mirror face operate from side to side and up and down with the 
mirror control switch operation.

Revision: 2008 October

2009 Murano

MIR-68

< FUNCTION DIAGNOSIS >

[WITHOUT ADP]

INSIDE MIRROR SYSTEM

INSIDE MIRROR SYSTEM

System Description

INFOID:0000000003554783

The sensor built in inside mirror detects the headlight of the vehicle behind and automatically changes the light
transmission to decrease the brightness.

Component Description

INFOID:0000000003554784

Component

Function

Auto anti-dazzling inside mirror

It automatically changes the light transmittance according to the brightness of the 
light from the headlight of the vehicle behind.

Revision: 2008 October

2009 Murano

DOOR MIRROR

MIR-69

< COMPONENT DIAGNOSIS >

[WITHOUT ADP]

C

D

E

F

G

H

I

J

K

M

A

B

MIR

N

O

P

COMPONENT DIAGNOSIS

DOOR MIRROR

Wiring Diagram - DOOR MIRROR SYSTEM (WITHOUT AUTOMATIC DRIVE POSI-
TIONER) -

INFOID:0000000003554785

JCLWM2740GB

Revision: 2008 October

2009 Murano

MIR-70

< COMPONENT DIAGNOSIS >

[WITHOUT ADP]

DOOR MIRROR

JCLWM2741GB

Revision: 2008 October

2009 Murano

AUTO ANTI-DAZZLING INSIDE MIRROR SYSTEM

MIR-71

< COMPONENT DIAGNOSIS >

[WITHOUT ADP]

C

D

E

F

G

H

I

J

K

M

A

B

MIR

N

O

P

AUTO ANTI-DAZZLING INSIDE MIRROR SYSTEM

Wiring Diagram - INSIDE MIRROR SYSTEM -

INFOID:0000000004786433

JCLWM2742GB

Revision: 2008 October

2009 Murano