Nissan Murano Z51 (2008 year). Manual - part 127

 

  Index      Manuals     Nissan Murano Z51 (2008 year) - Service and Repair Manual

 

Search            copyright infringement  

 

 

 

 

 

 

 

 

Content      ..     125      126      127      128     ..

 

 

Nissan Murano Z51 (2008 year). Manual - part 127

 

 

DLK-564

< ON-VEHICLE REPAIR >

[WITHOUT INTELLIGENT KEY SYSTEM]

BACK DOOR

BACK DOOR WEATHER-STRIP : Exploded View

INFOID:0000000004749841

BACK DOOR WEATHER-STRIP : Removal and Installation

INFOID:0000000004749844

REMOVAL

1.

Remove mounting bolts of power back door drive assembly (1)
(back door side).

2.

Pull up and remove engagement with body from weather-strip joint.

CAUTION:

Never pull strongly on weather-strip.

INSTALLATION

1.

Working from the upper section, align weather-strip center mark (A) with vehicle center mark (cutting posi-
tion) and install weather-strip onto the vehicle.

1.

Back door stay

2.

Back door hinge

3.

Back door striker

4.

Bumper rubber

5.

Back door weather-strip

6.

Back door assembly

7.

Stud ball

A

: Center mark

B

: Front mark

: Vehicle front

Refer to 

GI-4, "Components"

 for symbols in the figure.

JMKIA3496ZZ

JMKIA1918ZZ

Revision: 2008 October

2009 Murano

BACK DOOR

DLK-565

< ON-VEHICLE REPAIR >

[WITHOUT INTELLIGENT KEY SYSTEM]

C

D

E

F

G

H

I

J

L

M

A

B

DLK

N

O

P

2.

For the lower section, align weather-strip seam with center of back door striker.

3.

Pull weather-strip gently to ensure that there is no loose section.
NOTE:
Make sure that weather-strip is fit tightly at each corner and luggage rear plate.

4.

Install mounting bolts of power back door drive assembly (back door side).

Revision: 2008 October

2009 Murano

DLK-566

< ON-VEHICLE REPAIR >

[WITHOUT INTELLIGENT KEY SYSTEM]

HOOD LOCK

HOOD LOCK

Exploded View

INFOID:0000000004749845

Removal and Installation

INFOID:0000000004749846

REMOVAL

CAUTION:

Check wiring of hood lock control before removal.
1.

Remove front grille. Refer to 

EXT-18, "Removal and Installation"

.

2.

Remove mounting bolts, and then remove hood lock assembly
(1). 
NOTE:
Press the lever downward to avoid pin (A), then pull out hood
lock assembly upward.

3.

Disconnect hood lock cable (2) from hood lock assembly.

4.

Remove instrument lower panel (LH). Refer to 

IP-12, "Removal and Installation"

.

5.

Disconnect hood lock cable from instrument lower panel (LH).

6.

Remove fender protector (LH). Refer to 

EXT-23, "FENDER PROTECTOR : Removal and Installation"

.

7.

Remove hood lock cable clamp.

1.

Hood lock assembly

2.

Hood lock control cable

3.

Hood lock opener

: Clip

Refer to 

GI-4, "Components"

 for symbols in the figure.

JMKIA1798ZZ

JMKIA1914ZZ

Revision: 2008 October

2009 Murano

HOOD LOCK

DLK-567

< ON-VEHICLE REPAIR >

[WITHOUT INTELLIGENT KEY SYSTEM]

C

D

E

F

G

H

I

J

L

M

A

B

DLK

N

O

P

8.

Remove grommet on the lower dash, and pull the hood lock control cable toward the passenger compart-
ment.

CAUTION:

While pulling, never to damage (peeling) the outside of hood lock control cable.

INSTALLATION

Install in the reverse order of removal.

CAUTION:

• Never to bend cable too much, keeping the radius 100 mm (3.937 in) or more.
• Check that cable is not offset from the positioning grommet,

and apply the sealant to the grommet (at * mark) properly.

• Check that hood lock control cable is properly engaged with hood lock.
• After installation, perform hood fitting adjustment. Refer to 

DLK-538, "HOOD ASSEMBLY : Adjust-

ment"

.

• After installation, perform hood lock control inspection. Refer to 

DLK-567, "Inspection"

.

Inspection

INFOID:0000000004749847

NOTE:
If the hood lock cable is bent or deformed, replace it.
1.

Check that secondary latch is properly engaged with secondary striker [6.8 mm (0.268 in)] by hood
weight.

2.

While operating hood opener, carefully check that the front end of hood is raised by approximately 20.0
mm (0.787 in). Also check that hood opener returns to the original position.

3.

Check that hood opener operating is condition 49 N (5.0 kg, 11.0 lb) or below.

4.

Install so that static closing face of hood is 94 – 490 N·m (9.6 – 50.0 kg-m, 69 – 361 ft – lb).
NOTE:
• Exert vertical force on right side and left side of hood lock.
• Never press simultaneously both sides.

5.

Check the hood lock lubrication condition. If necessary, apply body grease to hood lock.

PIIB5801E

Revision: 2008 October

2009 Murano

DLK-568

< ON-VEHICLE REPAIR >

[WITHOUT INTELLIGENT KEY SYSTEM]

FRONT DOOR LOCK

FRONT DOOR LOCK

DOOR LOCK

DOOR LOCK : Exploded View

INFOID:0000000004749848

DOOR LOCK : Removal and Installation

INFOID:0000000004749849

REMOVAL

1.

Remove front door finisher. Refer to 

INT-11, "FRONT DOOR FINISHER : Removal and Installation"

.

2.

Remove front door glass. Refer to 

GW-17, "Removal and Installation"

.

3.

Remove front door module assembly. Refer to 

GW-20, "Removal and Installation"

.

4.

Disconnect door antenna and door request switch connector and remove harness clamp (models with
Intelligent Key system) on outside handle bracket.

1.

TORX bolt

2.

Key rod

3.

Door lock assembly

4.

Inside handle

5.

Front gasket

6.

Outside handle

7.

Door key cylinder assembly (driver 
side)
Outside handle escutcheon (passen-
ger side)

8.

Rear gasket

9.

Outside handle bracket

:Vehicle front

  : Apply genuine high strength thread locking sealant or equivalent.

Refer to 

GI-4, "Components"

 for symbols in the figure.

JMKIA1802GB

Revision: 2008 October

2009 Murano

FRONT DOOR LOCK

DLK-569

< ON-VEHICLE REPAIR >

[WITHOUT INTELLIGENT KEY SYSTEM]

C

D

E

F

G

H

I

J

L

M

A

B

DLK

N

O

P

5.

Remove door side grommet, and loosen TORX bolt from grom-
met hole.

CAUTION:

Never forcibly remove TORX bolt.

6.

Reach in to separate door key rod connection (on the handle)
(driver side).

7.

While pulling outside handle, remove door key cylinder assem-
bly (driver side) or outside handle escutcheon (passenger side).

8.

While pulling outside handle (1), slide toward rear of vehicle to
remove outside handle.

9.

Remove front gasket and rear gasket.

JMKIA0020ZZ

1.

Door key cylinder assembly

2.

Key rod

JMKIA0553ZZ

JMKIA0560ZZ

JMKIA0524ZZ

Revision: 2008 October

2009 Murano

DLK-570

< ON-VEHICLE REPAIR >

[WITHOUT INTELLIGENT KEY SYSTEM]

FRONT DOOR LOCK

10. While pulling outside handle bracket, slide toward rear of vehicle

to remove outside handle bracket.

11. Reach in to separate outside handle cable connection on outside handle bracket.
12. Remove door lock assembly TORX bolts.

13. Disconnect door lock actuator connector, and then remove door lock assembly.

14. Remove key rod from door lock assembly.

INSTALLATION

Install in the reverse order of removal.

CAUTION:

• To install each rod, rotate rod holder until a click is felt.
• Check door open/close, lock/unlock operation after installation. 

INSIDE HANDLE

INSIDE HANDLE : Exploded View

INFOID:0000000004749852

PIIB5814E

1.

TORX bolt

2.

Key rod

3.

Door lock assembly

4.

Inside handle

5.

Front gasket

6.

Outside handle

7.

Door key cylinder assembly (driver 
side)
Outside handle escutcheon (passen-
ger side)

8.

Rear gasket

9.

Outside handle bracket

JMKIA1802GB

Revision: 2008 October

2009 Murano

FRONT DOOR LOCK

DLK-571

< ON-VEHICLE REPAIR >

[WITHOUT INTELLIGENT KEY SYSTEM]

C

D

E

F

G

H

I

J

L

M

A

B

DLK

N

O

P

INSIDE HANDLE : Removal and Installation

INFOID:0000000004749854

REMOVAL

1.

Remove front door finisher. Refer to 

INT-11, "FRONT DOOR FINISHER : Removal and Installation"

.

2.

Remove inside handle mounting screws.

3.

Disconnect inside handle cable, and then remove the inside handle.

INSTALLATION

Install in the reverse order of removal.

CAUTION:

Check door open/close, lock/unlock operation after installation.

OUTSIDE HANDLE

OUTSIDE HANDLE : Exploded View

INFOID:0000000004749857

:Vehicle front

  : Apply genuine high strength thread locking sealant or equivalent.

Refer to 

GI-4, "Components"

 for symbols in the figure.

1.

TORX bolt

2.

Key rod

3.

Door lock assembly

4.

Inside handle

5.

Front gasket

6.

Outside handle

7.

Door key cylinder assembly (driver 
side)
Outside handle escutcheon (passen-
ger side)

8.

Rear gasket

9.

Outside handle bracket

:Vehicle front

  : Apply genuine high strength thread locking sealant or equivalent.

Refer to 

GI-4, "Components"

 for symbols in the figure.

JMKIA1802GB

Revision: 2008 October

2009 Murano

DLK-572

< ON-VEHICLE REPAIR >

[WITHOUT INTELLIGENT KEY SYSTEM]

FRONT DOOR LOCK

OUTSIDE HANDLE : Removal and Installation

INFOID:0000000004749859

REMOVAL

1.

Remove front door finisher. Refer to 

INT-11, "FRONT DOOR FINISHER : Removal and Installation"

.

2.

Remove front door glass. Refer to 

GW-17, "Removal and Installation"

.

3.

Remove front door module assembly. Refer to 

GW-17, "Removal and Installation"

.

4.

Disconnect door antenna and door request switch connector and remove harness clamp (models with
Intelligent Key system) on outside handle bracket.

5.

Remove door side grommet, and loosen TORX bolt from grom-
met hole.

CAUTION:

Never forcibly remove TORX bolt.

6.

Reach in to separate door key rod connection (on the handle)
(driver side).

7.

While pulling outside handle, remove door key cylinder assem-
bly (diver side) or outside handle escutcheon (passenger side).

8.

While pulling outside handle (1), slide toward rear of vehicle to
remove outside handle.

9.

Remove front gasket and rear gasket.

JMKIA0020ZZ

1.

Door key cylinder assembly

2.

Key rod

JMKIA0553ZZ

JMKIA0560ZZ

JMKIA0524ZZ

Revision: 2008 October

2009 Murano

FRONT DOOR LOCK

DLK-573

< ON-VEHICLE REPAIR >

[WITHOUT INTELLIGENT KEY SYSTEM]

C

D

E

F

G

H

I

J

L

M

A

B

DLK

N

O

P

10. While pulling outside handle bracket, slide toward rear of vehicle

to remove outside handle bracket.

11. Reach in to separate outside handle cable connection on outside handle bracket.

INSTALLATION

Install in the reverse order of removal.

CAUTION:

• To install each rod, rotate rod holder until a click is felt.
• Check door open/close, lock/unlock operation after installation.

PIIB5814E

Revision: 2008 October

2009 Murano

DLK-574

< ON-VEHICLE REPAIR >

[WITHOUT INTELLIGENT KEY SYSTEM]

REAR DOOR LOCK

REAR DOOR LOCK

DOOR LOCK

DOOR LOCK : Exploded View

INFOID:0000000004749860

DOOR LOCK : Removal and Installation

INFOID:0000000004749861

REMOVAL

1.

Fully close rear door glass.

2.

Remove rear door finisher. Refer to 

INT-15, "REAR DOOR FINISHER : Removal and Installation"

.

3.

Remove sealing screen. Refer to 

GW-23, "Removal and Installation"

.

4.

Remove door side grommet, and loosen TORX bolt from grom-
met hole.

1.

TORX bolt

2.

Door lock assembly

3.

Inside handle cap

4.

Inside handle

5.

Front gasket

6.

Outside handle

7.

Outside handle escutcheon

8.

Rear gasket

9.

Outside handle bracket

: Vehicle front

  : Apply genuine high strength thread locking sealant or equivalent.

Refer to 

GI-4, "Components"

 for symbols in the figure.

JMKIA1803GB

JMKIA1467ZZ

Revision: 2008 October

2009 Murano

REAR DOOR LOCK

DLK-575

< ON-VEHICLE REPAIR >

[WITHOUT INTELLIGENT KEY SYSTEM]

C

D

E

F

G

H

I

J

L

M

A

B

DLK

N

O

P

5.

While pulling outside handle, remove outside handle escutch-
eon.

6.

While pulling outside handle (1), slide toward rear of vehicle to
remove outside handle.

7.

Remove front gasket and rear gasket.

8.

While pulling outside handle bracket, slide toward rear of vehicle
to remove outside handle bracket.

9.

Reach in to separate outside handle cable connection on outside handle bracket.

10. Disconnect harness connector from door lock actuator.

11. Remove door lock mounting bolts.

12. Remove door lock assembly.

INSTALLATION

Install in the reverse order of removal.

CAUTION:

Check door open/close, lock/unlock operation after installation. 

INSIDE HANDLE

JMKIA0560ZZ

JMKIA0524ZZ

PIIB5814E

Revision: 2008 October

2009 Murano

DLK-576

< ON-VEHICLE REPAIR >

[WITHOUT INTELLIGENT KEY SYSTEM]

REAR DOOR LOCK

INSIDE HANDLE : Exploded View

INFOID:0000000004749864

INSIDE HANDLE : Removal and Installation

INFOID:0000000004749866

REMOVAL

1.

Remove rear door finisher. Refer to 

INT-15, "REAR DOOR FINISHER : Removal and Installation"

.

2.

Remove inside handle mounting screws.

3.

Disconnect inside handle cable, and then remove inside handle.

INSTALLATION

Install in the reverse order of removal.

CAUTION:

Check door open/close, lock/unlock operation after installation. 

OUTSIDE HANDLE

1.

TORX bolt

2.

Door lock assembly

3.

Inside handle cap

4.

Inside handle

5.

Front gasket

6.

Outside handle

7.

Outside handle escutcheon

8.

Rear gasket

9.

Outside handle bracket

: Vehicle front

  : Apply genuine high strength thread locking sealant or equivalent.

Refer to 

GI-4, "Components"

 for symbols in the figure.

JMKIA1803GB

Revision: 2008 October

2009 Murano

REAR DOOR LOCK

DLK-577

< ON-VEHICLE REPAIR >

[WITHOUT INTELLIGENT KEY SYSTEM]

C

D

E

F

G

H

I

J

L

M

A

B

DLK

N

O

P

OUTSIDE HANDLE : Exploded View

INFOID:0000000004749869

OUTSIDE HANDLE : Removal and Installation

INFOID:0000000004749871

REMOVAL

1.

Remove rear door finisher. Refer to 

INT-15, "REAR DOOR FINISHER : Removal and Installation"

.

2.

Fully close rear door glass.

3.

Remove sealing screen. Refer to 

GW-23, "Removal and Installation"

.

4.

Remove door side grommet, and loosen TORX bolt from grom-
met hole.

1.

TORX bolt

2.

Door lock assembly

3.

Inside handle cap

4.

Inside handle

5.

Front gasket

6.

Outside handle

7.

Outside handle escutcheon

8.

Rear gasket

9.

Outside handle bracket

: Vehicle front

  : Apply genuine high strength thread locking sealant or equivalent.

Refer to 

GI-4, "Components"

 for symbols in the figure.

JMKIA1803GB

JMKIA1467ZZ

Revision: 2008 October

2009 Murano

DLK-578

< ON-VEHICLE REPAIR >

[WITHOUT INTELLIGENT KEY SYSTEM]

REAR DOOR LOCK

5.

While pulling outside handle, remove outside handle escutch-
eon.

6.

While pulling outside handle (1), slide toward rear of vehicle to
remove outside handle.

7.

Remove front gasket and rear gasket.

8.

While pulling outside handle bracket, slide toward rear of vehicle
to remove outside handle bracket.

9.

Reach in to separate outside handle cable connection on outside handle bracket.

INSTALLATION

Install in the reverse order of removal.

CAUTION:

Check door open/close, lock/unlock operation after installation. 

JMKIA0560ZZ

JMKIA0524ZZ

PIIB5814E

Revision: 2008 October

2009 Murano

BACK DOOR LOCK

DLK-579

< ON-VEHICLE REPAIR >

[WITHOUT INTELLIGENT KEY SYSTEM]

C

D

E

F

G

H

I

J

L

M

A

B

DLK

N

O

P

BACK DOOR LOCK

DOOR LOCK

DOOR LOCK : Exploded View

INFOID:0000000004749872

DOOR LOCK : Removal and Installation

INFOID:0000000004749873

REMOVAL

1.

Remove back door finisher inner. Refer to 

INT-37, "Removal and Installation"

.

2.

Disconnect back door lock assembly and back door opener switch connectors.

3.

Remove back door lock mounting bolts, and then remove back door lock assembly.

JMKIA1804GB

1.

TORX bolt

2.

Back door assembly

3.

Power back door drive assembly

4.

Back door lock assembly (normal)

5.

Back door lock assembly (super lock)

6.

Touch sensor (RH/LH)

7.

Cover

8.

Patch

Refer to 

GI-4, "Components"

 for symbols in the figure.

Revision: 2008 October

2009 Murano

 

 

 

 

 

 

 

Content      ..     125      126      127      128     ..