DLK-404
< FUNCTION DIAGNOSIS >
[WITHOUT INTELLIGENT KEY SYSTEM]
DIAGNOSIS SYSTEM (BCM)
ACTIVE TEST
RKE-TR/BD
NOTE:
This item is displayed, but cannot be monitored.
RKE-PANIC
Indicates [ON/OFF] condition of PANIC button of keyfob.
RKE-P/W OPEN
Indicates [ON/OFF] condition of P/W DOWN signal from keyfob.
RKE-MODE CHG
Indicates [ON/OFF] condition of MODE CHANGE signal from keyfob.
RKE OPE COUN1
When remote keyless entry receiver receives the signal transmitted while operating on keyfob, the numer-
ical value start changing.
RKE OPE COUN2
NOTE:
This item is displayed, but cannot be monitored.
Monitor Item
Condition
Test item
Description
BATTERY SAVER
This test is able to check interior room lamp operation.
The interior room lamp will be activated after “ON” on CONSULT-III screen is touched.
PW REMOTO DOWN SET
This test is able to check power window down operation.
The power window down will be activated after “ON” on CONSULT-III screen is touched.
INT LAMP
This test is able to check interior room lamp operation.
The interior room lamp will be activated after “ON” on CONSULT-III screen is touched.
LCD
This test is able to check meter display information
• Engine start information displays when “B&P N” on CONSULT-III screen is touched.
• Engine start information displays when “B&P I” on CONSULT-III screen is touched.
• Key ID warning displays when “ID NG” on CONSULT-III screen is touched.
• Steering lock information displays when “ROTAT” on CONSULT-III screen is touched.
• P position warning displays when “SFT P” on CONSULT-III screen is touched.
• Intelligent Key insert information displays when “INSRT” on CONSULT-III screen is touched.
• Intelligent Key low battery warning displays when “BATT” on CONSULT-III screen is touched.
• Take away through window warning displays when “NO KY” on CONSULT-III screen is touched.
• Take away warning display when “OUTKY” on CONSULT-III screen is touched.
• OFF position warning display when “LK WN” on CONSULT-III screen is touched.
TRUNK/GLASS HATCH
This test is able to check back door opener actuator open operation.
This actuator opens when “ON” on CONSULT-III screen is touched.
FLASHER
This test is able to check security hazard lamp operation.
The hazard lamps will be activated after “ON” on CONSULT-III screen is touched.
HORN
This test is able to check horn operation.
The horn will be activated after “ON” on CONSULT-III screen is touched.
IGN CONT2
This test is able to check ignition relay operation.
The ignition relay will be activated after “ON” on CONSULT-III screen is touched.
P RANGE
This test is able to check control device power supply
Control device power is supplied when “ON” on CONSULT-III screen is touched.
ENGINE SW ILLUMI
This test is able to check push-ignition switch illumination operation.
Push-ignition switch illumination illuminates when “ON” on CONSULT-III screen is touched.
LOCK INDICATOR
NOTE:
This item is displayed, but cannot be tested.
ACC INDICATOR
This test is able to check indicator in push-ignition switch operation.
Indicator in push-ignition switch illuminates when “ON” on CONSULT-III screen is touched.
IGNITION ON IND
This test is able to check indicator in push-ignition switch operation.
Indicator in push-ignition switch illuminates when “ON” on CONSULT-III screen is touched.
KEY SLOT ILLUMI
This test is able to check key slot illumination operation.
Key slot illumination flash when “ON” on CONSULT-III screen is touched.
AUTOMATIC BACK DOOR
NOTE:
This item is displayed, but cannot be tested.
AUTOMATIC SLIDING DOOR
NOTE:
This item is displayed, but cannot be tested.
Revision: 2008 October
2009 Murano