Nissan Murano Z51 (2008 year). Manual

BCM (BODY CONTROL MODULE)

ADP-189

< ECU DIAGNOSIS >

ADP

C1708: [NO DATA] FL

—

WT-18

C1709: [NO DATA] FR

—

C1710: [NO DATA] RR

—

C1711: [NO DATA] RL

—

C1712: [CHECKSUM ERR] FL

—

WT-21

C1713: [CHECKSUM ERR] FR

—

C1714: [CHECKSUM ERR] RR

—

C1715: [CHECKSUM ERR] RL

—

C1716: [PRESSDATA ERR] FL

—

WT-24

C1717: [PRESSDATA ERR] FR

—

C1718: [PRESSDATA ERR] RR

—

C1719: [PRESSDATA ERR] RL

—

C1720: [CODE ERR] FL

—

WT-26

C1721: [CODE ERR] FR

—

C1722: [CODE ERR] RR

—

C1723: [CODE ERR] RL

—

C1724: [BATT VOLT LOW] FL

—

WT-29

C1725: [BATT VOLT LOW] FR

—

C1726: [BATT VOLT LOW] RR

—

C1727: [BATT VOLT LOW] RL

—

C1729: VHCL SPEED SIG ERR

—

WT-32

C1734: CONTROL UNIT

—

WT-33

CONSULT display

Fail-safe

Freeze Frame

Data

•Vehicle Speed

•Odo/Trip Meter

•Vehicle Condi-

tion

Intelligent Key

warning lamp ON

Tire pressure

monitor warning

lamp ON

Reference

page

Revision: 2008 October

2009 Murano

ADP-190

< SYMPTOM DIAGNOSIS >

ADP SYSTEM SYMPTOMS

SYMPTOM DIAGNOSIS

ADP SYSTEM SYMPTOMS

Symptom Table

INFOID:0000000003312497

The diagnostics item numbers show the sequence for inspection. Inspection in order from item 1.

Order

Function

Operation procedure

Symptom

Diagnostic item

Reference

page

Memory function

Perform memory storage
(Refer to

ADP-10

.) and

memory operation (Refer to

ADP-22

All parts do not operate in memory
function.

—

ADP-191

Memory indicator 1 or 2 does not oper-
ate.

—

ADP-192

Manual function

Perform manual function
(Refer to

ADP-18

All components of power seat do not
operate.

—

ADP-193

All components of tilt&telescopic do not
operate.

—

ADP-201

Manual function
and
memory function

Perform manual function
(Refer to

ADP-18

.) and

memory function (Refer to

ADP-22

.).

Manual function or memory function
does not operate. (for specific part)

Sliding

Reclining

Lifting (front)

Lifting (rear)

Steering tilt

Steering telescopic

Door mirror

Entry/exit assist
function

Perform entry/exit assist
function.
Exit assist function: Refer
to

ADP-26

Entry assist function: Refer
to

ADP-30

Entry/exit assist function does not op-
erate.

—

ADP-199

Intelligent Key in-
ter lock function

Perform Intelligent Key in-
ter lock function (Refer to

ADP-34

Intelligent Key inter lock function does
not operate.

—

ADP-200

Revision: 2008 October

2009 Murano

ALL PARTS DO NOT OPERATE IN MEMORY FUNCTION

ADP-191

< SYMPTOM DIAGNOSIS >

ADP

ALL PARTS DO NOT OPERATE IN MEMORY FUNCTION

Diagnosis Procedure

INFOID:0000000003312498

CHECK MEMORY FUNCTION

Check memory function.
Refer to

ADP-22, "MEMORY FUNCTION : System Description"

Is the inspection result normal?

YES

>> Memory function is normal.

>> GO TO 2.

CHECK SEAT MEMORY SWITCH

Check seat memory switch.
Refer to

ADP-66, "Component Function Check"

Is the inspection result normal?

YES

>> GO TO 3.

>> Repair or replace the malfunction parts.

CHECK DRIVER SEAT CONTROL UNIT POWER SUPPLY AND GROUND CIRCUIT

Check driver seat control unit power supply and ground circuit.
Refer to

ADP-52, "DRIVER SEAT CONTROL UNIT : Diagnosis Procedure"

Is the inspection result normal?

YES

>> GO TO 4.

>> Repair or replace the malfunction parts.

CHECK AUTOMATIC DRIVE POSITIONER CONTROL UNIT POWER SUPPLY AND GROUND CIRCUIT

Check automatic drive positioner control unit power supply and ground circuit.
Refer to

ADP-52, "AUTOMATIC DRIVE POSITIONER CONTROL UNIT : Diagnosis Procedure"

Is the inspection result normal?

YES

>> GO TO 5.

>> Repair or replace the malfunction parts.

PERFORM INITIALIZATION AND MEMORY STORING PROCEDURE

Perform initialization procedure.
Refer to

ADP-9, "SYSTEM INITIALIZATION : Special Repair Requirement"

Perform memory storing procedure.
Refer to

ADP-10, "MEMORY STORING : Special Repair Requirement"

Check memory function.
Refer to

ADP-22, "MEMORY FUNCTION : System Description"

Is the inspection result normal?

YES

>> Memory function is normal.

>> GO TO 6.

CONFIRM THE OPERATION

Confirm the operation again.

Is the result normal?

YES

>> Check intermittent incident. Refer to

GI-40, "Intermittent Incident"

>> GO TO 1.

Revision: 2008 October

2009 Murano

ADP-192

< SYMPTOM DIAGNOSIS >

MEMORY INDICATE DOES NOT OPERATE

MEMORY INDICATE DOES NOT OPERATE

Diagnosis Procedure

INFOID:0000000003312499

CHECK MEMORY INDICATOR

Check memory indicator.
Refer to

ADP-113, "Component Function Check"

Is the inspection result normal?

YES

>> GO TO 2.

>> Repair or replace the malfunction parts.

CONFIRM THE OPERATION

Confirm the operation again.

Is the result normal?

YES

>> Check intermittent incident. Refer to

GI-40, "Intermittent Incident"

>> GO TO 1.

Revision: 2008 October

2009 Murano

ALL COMPONENTS OF POWER SEAT DO NOT OPERATE

ADP-193

< SYMPTOM DIAGNOSIS >

ADP

ALL COMPONENTS OF POWER SEAT DO NOT OPERATE

Diagnosis Procedure

INFOID:0000000003312500

CHECK POWER SEAT SWITCH GROUND CIRCUIT

Check power seat switch ground circuit.
Refer to

ADP-74, "Diagnosis Procedure"

Is the inspection result normal?

YES

>> GO TO 2.

>> Repair or replace harness or connector.

CONFIRM THE OPERATION

Confirm the operation again.

Is the result normal?

YES

>> Check intermittent incident. Refer to

GI-40, "Intermittent Incident"

>> GO TO 1.

Revision: 2008 October

2009 Murano

ADP-194

< SYMPTOM DIAGNOSIS >

MANUAL FUNCTION OR MEMORY FUNCTION DOES NOT OPERATE

MANUAL FUNCTION OR MEMORY FUNCTION DOES NOT OPERATE

SEAT SLIDING

SEAT SLIDING : Diagnosis Procedure

INFOID:0000000003312501

CHECK SLIDING MECHANISM

Check for the following.
• Mechanism deformation or pinched foreign materials.
• Interference with other parts because of poor installation.

Is the inspection result normal?

YES

>> GO TO 2.

>> Repair or replace the malfunction parts.

CHECK SLIDING SWITCH

Check sliding switch.
Refer to

ADP-54, "Component Function Check"

Is the inspection result normal?

YES

>> GO TO 3.

>> Repair or replace the malfunction parts.

CHECK SLIDING MOTOR

Check sliding motor.
Refer to

ADP-99, "Component Function Check"

Is the inspection result normal?

YES

>> GO TO 4.

>> Repair or replace the malfunction parts.

CHECK SLIDING SENSOR

Check sliding sensor.
Refer to

ADP-78, "Component Function Check"

Is the inspection result normal?

YES

>> GO TO 5.

>> Repair or replace the malfunction parts.

CONFIRM THE OPERATION

Check the operation again.

Is the result normal?

YES

>> Check intermittent incident. Refer to

GI-40, "Intermittent Incident"

>> GO TO 1.

SEAT RECLINING

SEAT RECLINING : Diagnosis Procedure

INFOID:0000000003312502

CHECK RECLINING MECHANISM

Check for the following.
• Mechanism deformation or pinched foreign materials.
• Interference with other parts because of poor installation.

Is the inspection result normal?

YES

>> GO TO 2.

>> Repair or replace the malfunction parts.

CHECK RECLINING SWITCH

Check reclining switch.
Refer to

ADP-56, "Component Function Check"

Is the inspection result normal?

Revision: 2008 October

2009 Murano

MANUAL FUNCTION OR MEMORY FUNCTION DOES NOT OPERATE

ADP-195

< SYMPTOM DIAGNOSIS >

ADP

YES

>> GO TO 3.

>> Repair or replace the malfunction parts.

CHECK RECLINING MOTOR

Check reclining motor.
Refer to

ADP-101, "Component Function Check"

Is the inspection result normal?

YES

>> GO TO 4.

>> Repair or replace the malfunction parts.

CHECK RECLINING SENSOR

Check reclining sensor.
Refer to

ADP-81, "Component Function Check"

Is the inspection result normal?

YES

>> GO TO 5.

>> Repair or replace the malfunction parts.

CONFIRM THE OPERATION

Check the operation again.

Is the result normal?

YES

>> Check intermittent incident. Refer to

GI-40, "Intermittent Incident"

>> GO TO 1.

SEAT LIFTING (FRONT)

SEAT LIFTING (FRONT) : Diagnosis Procedure

INFOID:0000000003312503

CHECK LIFTING (FRONT) MECHANISM

Check for the following.
• Mechanism deformation or pinched foreign materials.
• Interference with other parts because of poor installation.
Is the inspection result normal?

YES

>> GO TO 2.

>> Repair or replace the malfunction parts.

CHECK LIFTING SWITCH (FRONT)

Check lifting switch (front).
Refer to

ADP-58, "Component Function Check"

Is the inspection result normal?

YES

>> GO TO 3.

>> Repair or replace the malfunction parts.

CHECK LIFTING MOTOR (FRONT)

Check lifting motor (front).
Refer to

ADP-103, "Component Function Check"

Is the inspection result normal?

YES

>> GO TO 4.

>> Repair or replace the malfunction parts.

CHECK LIFTING SENSOR (FRONT)

Check lifting sensor (front).
Refer to

ADP-84, "Component Function Check"

Is the inspection result normal?

YES

>> GO TO 5.

>> Repair or replace the malfunction parts.

CONFIRM THE OPERATION

Check the operation again.

Revision: 2008 October

2009 Murano

ADP-196

< SYMPTOM DIAGNOSIS >

MANUAL FUNCTION OR MEMORY FUNCTION DOES NOT OPERATE

Is the result normal?

YES

>> Check intermittent incident. Refer to

GI-40, "Intermittent Incident"

>> GO TO 1.

SEAT LIFTING (REAR)

SEAT LIFTING (REAR) : Diagnosis Procedure

INFOID:0000000003312504

CHECK LIFTING (REAR) MECHANISM

Check for the following.
• Mechanism deformation or pinched foreign materials.
• Interference with other parts because of poor installation.

Is the inspection result normal?

YES

>> GO TO 2.

>> Repair or replace the malfunction parts.

CHECK LIFTING SWITCH (REAR)

Check lifting switch (rear).
Refer to

ADP-60, "Component Function Check"

Is the inspection result normal?

YES

>> GO TO 3.

>> Repair or replace the malfunction parts.

CHECK LIFTING MOTOR (REAR)

Check lifting motor (rear).
Refer to

ADP-105, "Component Function Check"

Is the inspection result normal?

YES

>> GO TO 4.

>> Repair or replace the malfunction parts.

CHECK LIFTING SENSOR (REAR)

Check lifting sensor (rear).
Refer to

ADP-87, "Component Function Check"

Is the inspection result normal?

YES

>> GO TO 5.

>> Repair or replace the malfunction parts.

CONFIRM THE OPERATION

Check the operation again.

Is the result normal?

YES

>> Check intermittent incident. Refer to

GI-40, "Intermittent Incident"

>> GO TO 1.

STEERING TILT

STEERING TILT : Diagnosis Procedure

INFOID:0000000003312505

CHECK STEERING TILT MECHANISM

Check for the following.
• Mechanism deformation or pinched foreign materials.
• Interference with other parts because of poor installation.

Is the inspection result normal?

YES

>> GO TO 2.

>> Repair or replace the malfunction parts.

CHECK TILT SWITCH

Check tilt switch.
Refer to

ADP-62, "Component Function Check"

Revision: 2008 October

2009 Murano

MANUAL FUNCTION OR MEMORY FUNCTION DOES NOT OPERATE

ADP-197

< SYMPTOM DIAGNOSIS >

ADP

Is the inspection result normal?

YES

>> GO TO 3.

>> Repair or replace the malfunction parts.

CHECK TILT MOTOR

Check tilt motor.
Refer to

ADP-107, "Component Function Check"

Is the inspection result normal?

YES

>> GO TO 4.

>> Repair or replace the malfunction parts.

CHECK TILT SENSOR

Check steering tilt sensor.
Refer to

ADP-90, "Component Function Check"

Is the inspection result normal?

YES

>> GO TO 5.

>> Repair or replace the malfunction parts.

CONFIRM THE OPERATION

Check the operation again.
Is the result normal?

YES

>> Check intermittent incident. Refer to

GI-40, "Intermittent Incident"

>> GO TO 1.

STEERING TELESCOPIC

STEERING TELESCOPIC : Diagnosis Procedure

INFOID:0000000003312506

CHECK STEERING TELESCOPIC MECHANISM

Check for the following.
• Mechanism deformation or pinched foreign materials.
• Interference with other parts because of poor installation.

Is the inspection result normal?

YES

>> GO TO 2.

>> Repair or replace the malfunction parts.

CHECK TELESCOPIC SWITCH

Check telescopic switch.
Refer to

ADP-64, "Component Function Check"

Is the inspection result normal?

YES

>> GO TO 3.

>> Repair or replace the malfunction parts.

CHECK TELESCOPIC MOTOR

Check telescopic motor.
Refer to

ADP-109, "Component Function Check"

Is the inspection result normal?

YES

>> GO TO 4.

>> Repair or replace the malfunction parts.

CHECK TELESCOPIC SENSOR

Check steering telescopic sensor.
Refer to

ADP-92, "Component Function Check"

Is the inspection result normal?

YES

>> GO TO 5.

>> Repair or replace the malfunction parts.

CONFIRM THE OPERATION

Revision: 2008 October

2009 Murano

ADP-198

< SYMPTOM DIAGNOSIS >

MANUAL FUNCTION OR MEMORY FUNCTION DOES NOT OPERATE

Check the operation again.

Is the result normal?

YES

>> Check intermittent incident. Refer to

GI-40, "Intermittent Incident"

>> GO TO 1.

DOOR MIRROR

DOOR MIRROR : Diagnosis Procedure

INFOID:0000000003312507

CHECK DOOR MIRROR MECHANISM

Check for the following.
• Mechanism deformation or pinched foreign materials.
• Interference with other parts because of poor installation.

Is the inspection result normal?

YES

>> GO TO 2.

>> Repair or replace the malfunction parts.

CHECK MIRROR SWITCH

Check mirror switch.
Refer to

ADP-71, "MIRROR SWITCH : Component Function Check"

Is the inspection result normal?

YES

>> GO TO 3.

>> Repair or replace the malfunction parts.

CHECK MIRROR MOTOR

Check mirror motor.
Refer to

ADP-111, "Component Function Check"

Is the inspection result normal?

YES

>> GO TO 4.

>> Repair or replace the malfunction parts.

CHECK MIRROR SENSOR

Check mirror sensor.
Refer to

ADP-95, "DRIVER SIDE : Component Function Check"

. (Driver side)

Refer to

ADP-96, "PASSENGER SIDE : Component Function Check"

. (Passenger side)

Is the inspection result normal?

YES

>> GO TO 5.

>> Repair or replace the malfunction parts.

CONFIRM THE OPERATION

Check the operation again.
Is the result normal?

YES

>> Check intermittent incident. Refer to

GI-40, "Intermittent Incident"

>> GO TO 1.

Revision: 2008 October

2009 Murano

ENTRY/EXIT ASSIST FUNCTION DOES NOT OPERATE

ADP-199

< SYMPTOM DIAGNOSIS >

ADP

ENTRY/EXIT ASSIST FUNCTION DOES NOT OPERATE

Diagnosis Procedure

INFOID:0000000003515883

CHECK SYSTEM SETTING

Check system setting.
Refer to

ADP-11, "SYSTEM SETTING : Special Repair Requirement"

Check the operation.

Is the inspection result normal?

YES

>> Entry/Exit function is OK.

>> GO TO 2.

PERFORM SYSTEM INITIALIZATION

Perform system initialization.
Refer to

ADP-9, "SYSTEM INITIALIZATION : Special Repair Requirement"

Check the operation.

Is the inspection result normal?

YES

>> Entry/Exit function is OK.

>> GO TO 3.

CHECK FRONT DOOR SWITCH (DRIVER SIDE)

Check front door switch (driver side).
Refer to

DLK-103, "WITH AUTOMATIC BACK DOOR : Component Function Check"

Is the inspection result normal?

YES

>> GO TO 4.

>> Repair or replace the malfunction parts.

CONFIRM THE OPERATION

Confirm the operation again.
Is the result normal?

YES

>> Check intermittent incident. Refer to

GI-40, "Intermittent Incident"

>> GO TO 1.

Revision: 2008 October

2009 Murano

ADP-200

< SYMPTOM DIAGNOSIS >

INTELLIGENT KEY INTERLOCK FUNCTION DOES NOT OPERATE

INTELLIGENT KEY INTERLOCK FUNCTION DOES NOT OPERATE

Diagnosis Procedure

INFOID:0000000003312510

CHECK DOOR LOCK FUNCTION

Check door lock function.
Refer to

DLK-14, "Work Flow"

Is the inspection result normal?

YES

>> GO TO 2.

>> Repair or replace the malfunction parts.

PERFORM MEMORY STORING PROCEDURE

Perform memory storing procedure.
Refer to

ADP-10, "MEMORY STORING : Special Repair Requirement"

Check Intelligent Key interlock function.
Refer to

ADP-34, "INTELLIGENT KEY INTERLOCK FUNCTION : System Description"

Is the inspection result normal?

YES

>> Intelligent Key inter lock function is normal.

>> Replace driver seat control unit. Refer to

ADP-204, "Removal and Installation"

Revision: 2008 October

2009 Murano

ALL COMPONENTS OF TILT & TELESCOPIC SWITCH DO NOT OPERATE

ADP-201

< SYMPTOM DIAGNOSIS >

ADP

ALL COMPONENTS OF TILT & TELESCOPIC SWITCH DO NOT OPERATE

Diagnosis Procedure

INFOID:0000000003639907

CHECK TILT & TELESCOPIC SWITCH GROUND CIRCUIT

Check tilt & telescopic switch ground circuit.
Refer to

ADP-75, "Diagnosis Procedure"

Is the inspection result normal?

YES

>> GO TO 2.

>> Repair or replace harness or connector.

CONFIRM THE OPERATION

Confirm the operation again.

Is the result normal?

YES

>> Check intermittent incident. Refer to

GI-40, "Intermittent Incident"

>> GO TO 1.

Revision: 2008 October

2009 Murano

ADP-202

< SYMPTOM DIAGNOSIS >

NORMAL OPERATING CONDITION

NORMAL OPERATING CONDITION

Description

INFOID:0000000003312512

The following symptoms are normal operations, and they do not indicate a malfunction.

Symptom

Cause

Action to take

Reference page

Entry/exit assist function and
seat synchronization do not op-
erate.

No initialization has been performed.

Perform initialization.

ADP-9

Entry/exit assist function is disabled.
NOTE:
The entry/exit assist function and seat
synchronization function are disabled be-
fore delivery (initial setting).

Change the settings.

ADP-11

Entry assist function does not op-
erate.

Manual operation with power seat switch
was performed after exit assist function
execution.

Perform the memory

function.

ADP-30

Lumbar support does not per-
form memory operation.

The lumbar support system are con-
trolled independently with no link to the
automatic drive positioner system.

—

Lumbar support system:

SE-8

Memory function, entry/exit as-
sist function, or Intelligent Key in-
terlock function does not
operate.

The operating conditions are not fulfilled.

Fulfill the operation

conditions.

Memory function:

ADP-22

Exit assist function:

ADP-26

Entry assist function:

ADP-30

Intelligent Key interlock

function:

ADP-34

Revision: 2008 October

2009 Murano

PRECAUTIONS

ADP-203

< PRECAUTION >

ADP

PRECAUTION

PRECAUTIONS

Precaution for Supplemental Restraint System (SRS) "AIR BAG" and "SEAT BELT
PRE-TENSIONER"

INFOID:0000000003671419

The Supplemental Restraint System such as “AIR BAG” and “SEAT BELT PRE-TENSIONER”, used along
with a front seat belt, helps to reduce the risk or severity of injury to the driver and front passenger for certain
types of collision. This system includes seat belt switch inputs and dual stage front air bag modules. The SRS
system uses the seat belt switches to determine the front air bag deployment, and may only deploy one front
air bag, depending on the severity of a collision and whether the front occupants are belted or unbelted.
Information necessary to service the system safely is included in the “SRS AIRBAG” and “SEAT BELT” of this
Service Manual.

WARNING:

• To avoid rendering the SRS inoperative, which could increase the risk of personal injury or death in

the event of a collision which would result in air bag inflation, all maintenance must be performed by
an authorized NISSAN/INFINITI dealer.

• Improper maintenance, including incorrect removal and installation of the SRS, can lead to personal

injury caused by unintentional activation of the system. For removal of Spiral Cable and Air Bag
Module, see the “SRS AIRBAG”.

• Never use electrical test equipment on any circuit related to the SRS unless instructed to in this Ser-

vice Manual. SRS wiring harnesses can be identified by yellow and/or orange harnesses or harness
connectors.

PRECAUTIONS WHEN USING POWER TOOLS (AIR OR ELECTRIC) AND HAMMERS

When working near the Airbag Diagnosis Sensor Unit or other Airbag System sensors while ignition switch is
ON or engine is running, never use air or electric power tools or strike near the sensor(s) with a hammer.
Heavy vibration may activate the sensor(s), deploy the airbag(s), possibly cause serious injury.
When using air or electric power tools or hammers, always turn OFF ignition switch, disconnect the battery,
and wait 3 minutes or more before performing any service.

Revision: 2008 October

2009 Murano

ADP-204

< ON-VEHICLE REPAIR >

DRIVER SEAT CONTROL UNIT

ON-VEHICLE REPAIR

DRIVER SEAT CONTROL UNIT

Exploded View

INFOID:0000000003312516

Refer to

SE-99, "Exploded View"

Removal and Installation

INFOID:0000000003312517

REMOVAL

CAUTION:

When removing and installing, use shop cloths to protect parts from damage.

Remove the driver seat (1). Refer to

SE-106, "Removal and

Installation"

Remove the mounting nut (A).

Remove driver seat control unit (2).

INSTALLATION

Install in the reverse order of removal.

CAUTION:

Be sure to clump the harness to the right place.
NOTE:
After installing the driver seat, perform additional service when replacing control unit. Refer to

ADP-8, "ADDI-

TIONAL SERVICE WHEN REPLACING CONTROL UNIT : Description"

JMJIA1449ZZ

Revision: 2008 October

2009 Murano

Nissan Murano Z51 (2008 year). Manual - part 13