The Supplemental Restraint System such as “AIR BAG” and “SEAT BELT PRE-TENSIONER”, used along
with a front seat belt, helps to reduce the risk or severity of injury to the driver and front passenger for certain
types of collision. This system includes seat belt switch inputs and dual stage front air bag modules. The SRS
system uses the seat belt switches to determine the front air bag deployment, and may only deploy one front
air bag, depending on the severity of a collision and whether the front occupants are belted or unbelted.
Information necessary to service the system safely is included in the “SRS AIRBAG” and “SEAT BELT” of this
Service Manual.

WARNING:

• To avoid rendering the SRS inoperative, which could increase the risk of personal injury or death in

the event of a collision which would result in air bag inflation, all maintenance must be performed by
an authorized NISSAN/INFINITI dealer.

• Improper maintenance, including incorrect removal and installation of the SRS, can lead to personal

injury caused by unintentional activation of the system. For removal of Spiral Cable and Air Bag
Module, see the “SRS AIRBAG”.

• Never use electrical test equipment on any circuit related to the SRS unless instructed to in this Ser-

vice Manual. SRS wiring harnesses can be identified by yellow and/or orange harnesses or harness
connectors.

PRECAUTIONS WHEN USING POWER TOOLS (AIR OR ELECTRIC) AND HAMMERS

When working near the Airbag Diagnosis Sensor Unit or other Airbag System sensors while ignition switch is
ON or engine is running, never use air or electric power tools or strike near the sensor(s) with a hammer.
Heavy vibration may activate the sensor(s), deploy the airbag(s), possibly cause serious injury.
When using air or electric power tools or hammers, always turn OFF ignition switch, disconnect the battery,
and wait 3 minutes or more before performing any service.

Revision: 2008 October

2009 Murano

ACCELERATOR CONTROL SYSTEM

ACC-3

< ON-VEHICLE REPAIR >

ACC

ON-VEHICLE REPAIR

ACCELERATOR CONTROL SYSTEM

Exploded View

INFOID:0000000003304332

Removal and Installation

INFOID:0000000003304333

REMOVAL

Disconnect accelerator pedal position sensor harness connector.

Remove accelerator pedal assembly.

CAUTION:

• Never disengage accelerator pedal assembly and bracket.
• Never disassemble accelerator lever. Never remove accelerator pedal position sensor from

accelerator lever.

• Avoid impact from dropping etc. during handling.
• Be careful to keep accelerator lever away from water.

INSTALLATION

Install in the reverse order of removal.

Inspection

INFOID:0000000003304334

INSPECTION AFTER INSTALLATION

Accelerator pedal assembly

: Vehicle front

Refer to

GI-4, "Components"

for symbols in the figure.

JPBIA1692GB

Revision: 2008 October

2009 Murano

ACC-4

< ON-VEHICLE REPAIR >

ACCELERATOR CONTROL SYSTEM

• Check accelerator pedal moves smoothly within the whole operation range when it is fully depressed and

released.

• Check accelerator pedal securely returns to the fully released position.
• For the electrical inspection of accelerator pedal position sensor, refer to

EC-415, "Component Inspection"

EC-418, "Component Inspection"

and

EC-426, "Component Inspection"

CAUTION:

When harness connector of accelerator pedal position sensor is disconnected, perform “Accelerator
Pedal Released Position Learning”. Refer to

EC-17, "ACCELERATOR PEDAL RELEASED POSITION

LEARNING : Description"

Revision: 2008 October

2009 Murano

ADP-1

BODY INTERIOR

SECTION

ADP

ADP

CONTENTS

AUTOMATIC DRIVE POSITIONER

BASIC INSPECTION ....................................

DIAGNOSIS AND REPAIR WORK FLOW .........

Work Flow .................................................................

INSPECTION AND ADJUSTMENT .....................

ADDITIONAL SERVICE WHEN REMOVING BAT-
TERY NEGATIVE TERMINAL .....................................

ADDITIONAL SERVICE WHEN REMOVING
BATTERY NEGATIVE TERMINAL : Description ......

ADDITIONAL SERVICE WHEN REMOVING
BATTERY NEGATIVE TERMINAL : Special Re-
pair Requirement .......................................................

ADDITIONAL SERVICE WHEN REPLACING
CONTROL UNIT ..........................................................

ADDITIONAL SERVICE WHEN REPLACING
CONTROL UNIT : Description ..................................

ADDITIONAL SERVICE WHEN REPLACING
CONTROL UNIT : Special Repair Requirement .......

SYSTEM INITIALIZATION ..........................................

SYSTEM INITIALIZATION : Description ...................

SYSTEM INITIALIZATION : Special Repair Re-
quirement ..................................................................

MEMORY STORING ....................................................

MEMORY STORING : Description ............................

MEMORY STORING : Special Repair Require-
ment ........................................................................

SYSTEM SETTING ....................................................

SYSTEM SETTING : Description ............................

SYSTEM SETTING : Special Repair Requirement

....

FUNCTION DIAGNOSIS ..............................

AUTOMATIC DRIVE POSITIONER SYSTEM ....

AUTOMATIC DRIVE POSITIONER SYSTEM ...........

AUTOMATIC DRIVE POSITIONER SYSTEM :
System Diagram ......................................................

AUTOMATIC DRIVE POSITIONER SYSTEM :
System Description ..................................................

AUTOMATIC DRIVE POSITIONER SYSTEM :
Component Parts Location ......................................

AUTOMATIC DRIVE POSITIONER SYSTEM :
Component Description ..........................................

MANUAL FUNCTION ................................................

MANUAL FUNCTION : System Diagram ................

MANUAL FUNCTION : System Description ............

MANUAL FUNCTION : Component Parts Loca-
tion ...........................................................................

MANUAL FUNCTION : Component Description .....

MEMORY FUNCTION ................................................

MEMORY FUNCTION : System Diagram ...............

MEMORY FUNCTION : System Description ...........

MEMORY FUNCTION : Component Parts Loca-
tion ...........................................................................

MEMORY FUNCTION : Component Description ....

EXIT ASSIST FUNCTION ..........................................

EXIT ASSIST FUNCTION : System Diagram ..........

EXIT ASSIST FUNCTION : System Description .....

EXIT ASSIST FUNCTION : Component Parts Lo-
cation .......................................................................

EXIT ASSIST FUNCTION :
Component Description ..........................................

ENTRY ASSIST FUNCTION ......................................

ENTRY ASSIST FUNCTION : System Diagram .....

ENTRY ASSIST FUNCTION : System Description

....

ENTRY ASSIST FUNCTION : Component Parts
Location ...................................................................

ENTRY ASSIST FUNCTION :
Component Description ..........................................

INTELLIGENT KEY INTERLOCK FUNCTION ..........

Revision: 2008 October

2009 Murano

ADP-2

INTELLIGENT KEY INTERLOCK FUNCTION :
System Diagram .....................................................

INTELLIGENT KEY INTERLOCK FUNCTION :
System Description .................................................

INTELLIGENT KEY INTERLOCK FUNCTION :
Component Parts Location .....................................

INTELLIGENT KEY INTERLOCK FUNCTION :
Component Description .........................................

DIAGNOSIS SYSTEM (DRIVER SEAT CON-
TROL UNIT) .......................................................

Diagnosis Description .............................................

CONSULT-III Function ...........................................

COMPONENT DIAGNOSIS ........................

U1000 CAN COMM CIRCUIT ............................

Description ..............................................................

DTC Logic ...............................................................

Diagnosis Procedure .............................................

Special Repair Requirement ...................................

U1010 CONTROL UNIT (CAN) .........................

Description ..............................................................

DTC Logic ...............................................................

Diagnosis Procedure ..............................................

B2130 EEPROM ................................................

DTC Logic ...............................................................

Diagnosis Procedure .............................................

B2112 SLIDING MOTOR ...................................

Description ..............................................................

DTC Logic ...............................................................

Diagnosis Procedure .............................................

B2113 RECLINING MOTOR ..............................

Description ..............................................................

DTC Logic ...............................................................

Diagnosis Procedure .............................................

B2116 TILT MOTOR ..........................................

Description ..............................................................

DTC Logic ...............................................................

Diagnosis Procedure .............................................

B2128 UART COMMUNICATION LINE ............

Description ..............................................................

DTC Logic ...............................................................

Diagnosis Procedure .............................................

POWER SUPPLY AND GROUND CIRCUIT .....

DRIVER SEAT CONTROL UNIT ..............................

DRIVER SEAT CONTROL UNIT :
Diagnosis Procedure .............................................

DRIVER SEAT CONTROL UNIT : Special Repair
Requirement ...........................................................

AUTOMATIC DRIVE POSITIONER CONTROL
UNIT ..........................................................................

AUTOMATIC DRIVE POSITIONER CONTROL
UNIT : Diagnosis Procedure ..................................

AUTOMATIC DRIVE POSITIONER CONTROL
UNIT : Special Repair Requirement ........................

SLIDING SWITCH .............................................

Description ..............................................................

Component Function Check ..................................

Diagnosis Procedure ..............................................

Component Inspection ............................................

RECLINING SWITCH ........................................

Description ..............................................................

Component Function Check ..................................

Diagnosis Procedure ..............................................

Component Inspection ............................................

LIFTING SWITCH (FRONT) ..............................

Description ..............................................................

Component Function Check ..................................

Diagnosis Procedure ..............................................

Component Inspection ............................................

LIFTING SWITCH (REAR) ................................

Description ..............................................................

Component Function Check ..................................

Diagnosis Procedure ..............................................

Component Inspection ............................................

TILT SWITCH ....................................................

Description ..............................................................

Component Function Check ..................................

Diagnosis Procedure ..............................................

Component Inspection ............................................

TELESCOPIC SWITCH .....................................

Description ..............................................................

Component Function Check ..................................

Diagnosis Procedure ..............................................

Component Inspection ............................................

SEAT MEMORY SWITCH .................................

Description ..............................................................

Component Function Check ..................................

Diagnosis Procedure ..............................................

Component Inspection ............................................

DOOR MIRROR REMOTE CONTROL
SWITCH .............................................................

CHANGEOVER SWITCH ..........................................

CHANGEOVER SWITCH : Description ..................

CHANGEOVER SWITCH : Component Function
Check ......................................................................

CHANGEOVER SWITCH : Diagnosis Procedure ...

CHANGEOVER SWITCH : Component Inspec-
tion ..........................................................................

MIRROR SWITCH .....................................................

MIRROR SWITCH : Description .............................

MIRROR SWITCH : Component Function Check ...

Revision: 2008 October

2009 Murano

ADP-3

ADP

MIRROR SWITCH : Diagnosis Procedure ..............

MIRROR SWITCH : Component Inspection ...........

POWER SEAT SWITCH GROUND CIRCUIT ....

Diagnosis Procedure ..............................................

TILT &TELESCOPIC SWITCH GROUND CIR-
CUIT ....................................................................

Diagnosis Procedure ...............................................

FRONT DOOR SWITCH (DRIVER SIDE) ..........

Description ..............................................................

Component Function Check ....................................

Diagnosis Procedure ...............................................

Component Inspection ............................................

SLIDING SENSOR .............................................

Description ..............................................................

Component Function Check ..................................

Diagnosis Procedure ..............................................

RECLINING SENSOR ........................................

Description ..............................................................

Component Function Check ..................................

Diagnosis Procedure ..............................................

LIFTING SENSOR (FRONT) ..............................

Description ..............................................................

Component Function Check ..................................

Diagnosis Procedure ..............................................

LIFTING SENSOR (REAR) ................................

Description ..............................................................

Component Function Check ..................................

Diagnosis Procedure ..............................................

TILT SENSOR ....................................................

Description ..............................................................

Component Function Check ..................................

Diagnosis Procedure ..............................................

TELESCOPIC SENSOR .....................................

Description ..............................................................

Component Function Check ..................................

Diagnosis Procedure ..............................................

MIRROR SENSOR .............................................

DRIVER SIDE ............................................................

DRIVER SIDE : Description ....................................

DRIVER SIDE : Component Function Check ........

DRIVER SIDE : Diagnosis Procedure ....................

PASSENGER SIDE ...................................................

PASSENGER SIDE : Description ...........................

PASSENGER SIDE :
Component Function Check ..................................

PASSENGER SIDE : Diagnosis Procedure ...........

SLIDING MOTOR ...............................................

Description ..............................................................

Component Function Check ..................................

Diagnosis Procedure ..............................................

RECLINING MOTOR .......................................

101

Description .............................................................

101

Component Function Check ................................

101

Diagnosis Procedure ............................................

101

LIFTING MOTOR (FRONT) .............................

103

Description .............................................................

103

Component Function Check ................................

103

Diagnosis Procedure ............................................

103

LIFTING MOTOR (REAR) ...............................

105

Description .............................................................

105

Component Function Check ................................

105

Diagnosis Procedure ............................................

105

TILT MOTOR ...................................................

107

Description .............................................................

107

Component Function Check ................................

107

Diagnosis Procedure ............................................

107

TELESCOPIC MOTOR ...................................

109

Description .............................................................

109

Component Function Check ................................

109

Diagnosis Procedure ............................................

109

DOOR MIRROR MOTOR ................................

111

Description .............................................................

111

Component Function Check ..................................

111

Diagnosis Procedure .............................................

111

Component Inspection ...........................................

112

SEAT MEMORY INDICATOR .........................

113

Description .............................................................

113

Component Function Check ................................

113

Diagnosis Procedure ............................................

113

ECU DIAGNOSIS .......................................

115

DRIVER SEAT CONTROL UNIT ....................

115

Reference Value ....................................................

115

Wiring Diagram - AUTOMATIC DRIVE POSI-
TIONER CONTROL SYSTEM - ............................

121

Fail Safe ................................................................

130

DTC Index .............................................................

131

AUTOMATIC DRIVE POSITIONER CON-
TROL UNIT ......................................................

132

Reference Value ....................................................

132

Wiring Diagram - AUTOMATIC DRIVE POSI-
TIONER CONTROL SYSTEM - ............................

135

BCM (BODY CONTROL MODULE) ...............

145

Reference Value ....................................................

145

Wiring Diagram - BCM - ........................................

169

Fail-safe .................................................................

183

DTC Inspection Priority Chart .............................

186

DTC Index .............................................................

187

SYMPTOM DIAGNOSIS ............................

190

Revision: 2008 October

2009 Murano

ADP-4

ADP SYSTEM SYMPTOMS ............................

190

Symptom Table .....................................................

190

ALL PARTS DO NOT OPERATE IN MEMORY
FUNCTION .......................................................

191

Diagnosis Procedure .............................................

191

MEMORY INDICATE DOES NOT OPERATE .

192

Diagnosis Procedure .............................................

192

ALL COMPONENTS OF POWER SEAT DO
NOT OPERATE ...............................................

193

Diagnosis Procedure .............................................

193

MANUAL FUNCTION OR MEMORY FUNC-
TION DOES NOT OPERATE ...........................

194

SEAT SLIDING .........................................................

194

SEAT SLIDING : Diagnosis Procedure .................

194

SEAT RECLINING ...................................................

194

SEAT RECLINING : Diagnosis Procedure ............

194

SEAT LIFTING (FRONT) .........................................

195

SEAT LIFTING (FRONT) : Diagnosis Procedure ..

195

SEAT LIFTING (REAR) ............................................

196

SEAT LIFTING (REAR) : Diagnosis Procedure .....

196

STEERING TILT .......................................................

196

STEERING TILT : Diagnosis Procedure ...............

196

STEERING TELESCOPIC .......................................

197

STEERING TELESCOPIC : Diagnosis Procedure ..

197

DOOR MIRROR .......................................................

198

DOOR MIRROR : Diagnosis Procedure ................

198

ENTRY/EXIT ASSIST FUNCTION DOES NOT
OPERATE ........................................................

199

Diagnosis Procedure .............................................

199

INTELLIGENT KEY INTERLOCK FUNCTION
DOES NOT OPERATE .....................................

200

Diagnosis Procedure .............................................

200

ALL COMPONENTS OF TILT & TELESCOP-
IC SWITCH DO NOT OPERATE ......................

201

Diagnosis Procedure .............................................

201

NORMAL OPERATING CONDITION ...............

202

Description ............................................................

202

PRECAUTION ...........................................

203

PRECAUTIONS ................................................

203

Precaution for Supplemental Restraint System
(SRS) "AIR BAG" and "SEAT BELT PRE-TEN-
SIONER" ...............................................................

203

ON-VEHICLE REPAIR ..............................

204

DRIVER SEAT CONTROL UNIT ......................

204

Exploded View ......................................................

204

Removal and Installation .......................................

204

AUTOMATIC DRIVE POSITIONER CON-
TROL UNIT .......................................................

205

Exploded View ......................................................

205

Removal and Installation .......................................

205

SEAT MEMORY SWITCH ................................

206

Exploded View ......................................................

206

Removal and Installation .......................................

206

POWER SEAT SWITCH ...................................

207

Exploded View ......................................................

207

Removal and Installation .......................................

207

TILT&TELESCOPIC SWITCH ..........................

208

Exploded View ......................................................

208

Removal and Installation .......................................

208

Revision: 2008 October

2009 Murano

DIAGNOSIS AND REPAIR WORK FLOW

ADP-5

< BASIC INSPECTION >

ADP

BASIC INSPECTION

DIAGNOSIS AND REPAIR WORK FLOW

Work Flow

INFOID:0000000003312315

OVERALL SEQUENCE

DETAILED FLOW

JMJIA1702GB

Revision: 2008 October

2009 Murano

ADP-6

< BASIC INSPECTION >

DIAGNOSIS AND REPAIR WORK FLOW

GET INFORMATION FOR SYMPTOM

Get the detailed information from the customer about the symptom (the condition and the environment when
the incident/malfunction occurred).

>> GO TO 2.

CHECK DTC WITH AUTOMATIC DRIVE POSITIONER SYSTEM

Check “Self Diagnostic Result” with CONSULT-III. Refer to

ADP-131, "DTC Index"

Is any symptom described and any DTC is displayed?

Symptom is described, DTC is displayed.>>GO TO 3.
Symptom is not described, DTC is displayed.>>GO TO 6.
Symptom is described, DTC is not displayed.>>GO TO 4.

CONFIRM THE SYMPTOM

Try to confirm the symptom described by the customer.

>> GO TO 6.

CONFIRM THE SYMPTOM

Try to confirm the symptom described by the customer.

>> GO TO 5.

CHECK NORMAL OPERATING CONDITION

Check normal operating condition. Refer to

ADP-202, "Description"

Is the incident normal operation?

YES

>> INSPECTION END

>> GO TO 7.

PERFORM DTC CONFIRMATION PROCEDURE

Perform the confirmation procedure for the detected DTC.

Is the DTC displayed?

YES

>> GO TO 8.

>> Check intermittent incident. Refer to

GI-40, "Intermittent Incident"

PERFORM COMPONENT FUNCTION CHECK

Perform the component function check for the isolated malfunctioning point.

>> GO TO 8.

DETECT MALFUNCTIONING PART BY DIAGNOSTIC PROCEDURE

Isolate the malfunctioning point by performing the diagnosis procedure relevant to the symptom during the
component diagnosis.

>> GO TO 9.

REPARE OR REPLACE THE MALFUNCTIONING PARTS

Repair or replace the malfunctioning part.

>> GO TO 10.

10.

FINAL CHECK

Perform the DTC confirmation procedure (if DTC is detected) or component function check (if no DTC is
detected) again, and then check that the malfunction can be repaired securely.

Are all malfunctions corrected?

Revision: 2008 October

2009 Murano

DIAGNOSIS AND REPAIR WORK FLOW

ADP-7

< BASIC INSPECTION >

ADP

YES

>> INSPECTION END

Symptom is detected.>> GO TO 5.
DTC is detected.>> GO TO 6.

Revision: 2008 October

2009 Murano

ADP-8

< BASIC INSPECTION >

INSPECTION AND ADJUSTMENT

INSPECTION AND ADJUSTMENT

ADDITIONAL SERVICE WHEN REMOVING BATTERY NEGATIVE TERMINAL

ADDITIONAL SERVICE WHEN REMOVING BATTERY NEGATIVE TERMINAL : De-
scription

INFOID:0000000003312316

Each function is reset to the following condition when the battery terminal is disconnected.

: Default value is 40mm.

NOTE:
Notice that disconnecting the battery when detected DTC are present will erase the DTC memory.

ADDITIONAL SERVICE WHEN REMOVING BATTERY NEGATIVE TERMINAL : Spe-
cial Repair Requirement

INFOID:0000000003312317

SYSTEM INITIALIZATION

Perform system initialization. Refer to

ADP-9, "SYSTEM INITIALIZATION : Description"

>> GO TO 2.

SYSTEM SETTING

Perform system setting. Refer to

ADP-11, "SYSTEM SETTING : Description"

>> GO TO 3.

MEMORY STORAGE

Perform memory storage. Refer to

ADP-9, "MEMORY STORING : Description"

>> END

ADDITIONAL SERVICE WHEN REPLACING CONTROL UNIT

ADDITIONAL SERVICE WHEN REPLACING CONTROL UNIT : Description

INFOID:0000000003312318

Each function is reset to the following condition when the driver seat control unit is replaced.

: Default value is 40mm.

NOTE:
Notice that disconnecting the battery when detected DTC are present will erase the DTC memory.

ADDITIONAL SERVICE WHEN REPLACING CONTROL UNIT : Special Repair Re-

Function

Condition

Procedure

Memory (Seat, steering, mirror)

Erased

Perform storing

Entry/exit assist

OFF

Perform initialization

Set slide amount

Intelligent Key interlock

Erased

Perform initialization

Perform storing

Function

Condition

Procedure

Memory (Seat, steering, mirror)

Erased

Perform storing

Entry/exit assist

OFF

Perform initialization

Set slide amount

Intelligent Key interlock

Erased

Perform initialization

Perform storing

Revision: 2008 October

2009 Murano

INSPECTION AND ADJUSTMENT

ADP-9

< BASIC INSPECTION >

ADP

quirement

INFOID:0000000003312319

SYSTEM INITIALIZATION

Perform system initialization. Refer to

ADP-9, "SYSTEM INITIALIZATION : Description"

>> GO TO 2.

SYSTEM SETTING

Perform system setting. Refer to

ADP-11, "SYSTEM SETTING : Description"

>> GO TO 3.

MEMORY STORAGE

Perform memory storage. Refer to

ADP-9, "MEMORY STORING : Description"

>> END

SYSTEM INITIALIZATION

SYSTEM INITIALIZATION : Description

INFOID:0000000003312320

Always perform the initialization when the battery terminal is disconnected or the driver seat control unit is
replaced.
The entry/exit assist function will not operate normally if no initialization is performed.

SYSTEM INITIALIZATION : Special Repair Requirement

INFOID:0000000003312321

INITIALIZATION PROCEDURE

CHOOSE METHOD

There are two initialization methods.

Which method do you use?

With door switch>>GO TO 2.
With vehicle speed>>GO TO 4.

STEP A-1

Turn ignition switch from ACC to OFF position.

>> GO TO 3.

STEP A-2

Driver door switch is ON (open)

→

OFF (close)

→

ON (open).

>> END

STEP B-1

Drive the vehicle at more than 25 km/h (16 MPH).

>> END

MEMORY STORING

MEMORY STORING : Description

INFOID:0000000003312322

Always perform the memory storage when the battery terminal is disconnected or the driver seat control unit is
replaced. The memory function and Intelligent Key interlock function will not operate normally if no memory
storage is performed.

Revision: 2008 October

2009 Murano

ADP-10

< BASIC INSPECTION >

INSPECTION AND ADJUSTMENT

MEMORY STORING : Special Repair Requirement

INFOID:0000000003312323

Memory Storage Procedure

Two positions for the driver seat, steering column and outside mirror can be stored for memory operation by
following procedure.

STEP 1

Shift AT selector lever to P position.

>> GO TO 2.

STEP 2

Turn ignition switch ON.

>> GO TO 3.

STEP 3

Adjust driver seat, steering column and outside mirror position manually.

>> GO TO 4.

STEP 4

Push set switch.
NOTE:
• Memory indicator for which driver seat position is already retained in memory is illuminated for 5 sec-

onds.

• Memory indicator for which driver seat position is not retained in memory is illuminated for 0.5 second.

Push the memory switch (1 or 2) for at least 1 second within 5 seconds after pushing the set switch.
NOTE:
• To enter driver seat positions into blank memory, memory indicator will be turned on for 5 seconds.
• To modify driver seat positions, memory indicator will be turned OFF for 0.5 second, then turned ON for

5 seconds.

NOTE:
If memory is stored in the same memory switch, the previous memory will be deleted.

Do you need linking of Intelligent Key?

YES

>> GO TO 6.

>> GO TO 5.

STEP 5

Confirm the operation of each part with memory operation.

>> END

STEP 6

Push the Intelligent Key unlock button within 5 seconds after pushing memory switch (while the memory indi-
cator is turned ON).

>> GO TO 7.

STEP 7

Confirm the operation of each part with memory operation and lntelligent Key interlock operation.

>> END

SYSTEM SETTING

Revision: 2008 October

2009 Murano

INSPECTION AND ADJUSTMENT

ADP-11

< BASIC INSPECTION >

ADP

SYSTEM SETTING : Description

INFOID:0000000003312324

The settings of the automatic driving positioner system can be changed, using CONSULT-III, the display unit
in the center of the instrument panel and the set switch. Always check the settings before and after discon-
necting the battery terminal or replacing driver seat control unit.

Setting Change

: Applicable

SYSTEM SETTING : Special Repair Requirement

INFOID:0000000003312325

CHOOSE METHOD

There are three way of setting method.

Which method do you choose?

With display>>GO TO 2.
With set switch>>GO TO 4.
With CONSULT-III>>GO TO 6.

WITH DISPLAY - STEP 1

Turn ignition switch ON.

>> GO TO 3.

WITH DISPLAY - STEP 2

Push “SETTING” button.

Select “Comfort & convenience”.

Select “Lift Steering Wheel ON Exit”or “Slide Driver

′

s Seat Back ON Exit” on display, then push

Lift Steering Wheel ON Exit: Entry/exit assist (steering column)

Slide Driver's Seat Back On Exit: Entry/exit assist (seat)

>> END

WITH SET SWITCH - STEP 1

Turn ignition switch OFF.

>> GO TO 5.

WITH SET SWITCH - STEP 2

Push setting button and hold for more than 10 seconds, then confirm blinking of the memory switch indicator.
• Entry/exit assist (seat/steering column) are ON: Memory switch indicator blink two times.
• Entry/exit assist (seat/steering column) are OFF: Memory switch indicator blink once.

>> END

WITH CONSULT-III - STEP 1

Item

Content

CON-

SULT

–III

Display

Set

switch

Factory

setting

Amount of seat sliding for
entry/exit assist

The amount of seat sliding for entry/exit assist can
be selected from 3 items.
[40mm/80mm/150mm]

—

40mm

Entry/exit assist
(seat)

Entry/exit assist (seat) can be selected:
ON (operated) – OFF (not operated)

Entry/exit assist
(steering column)

Entry/exit assist (steering column) can be selected:
ON (operated) – OFF (not operated)

Reset custom settings

All settings can be set to default (factory setting).

—

Revision: 2008 October

2009 Murano

ADP-12

< BASIC INSPECTION >

INSPECTION AND ADJUSTMENT

Select “Work support”.

>> GO TO 7.

WITH CONSULT-III - STEP 2

Select “EXIT SEAT SLIDE SETTING”, “EXIT TILT SETTING” or “SEAT SLIDE VOLUME SET” then touch
display to change between ON and OFF.

EXIT SEAT SLIDE SETTING: Entry/exit assist (seat)

EXIT TILT SETTING: Entry/exit assist (steering column)

Then touch “OK”.

>> END

Revision: 2008 October

2009 Murano

Content .. 1 2 ..

///////////////////////////////////////