Nissan Juke (2014 year). Service Repair Manual - part 274

 

  Index      Manuals     Nissan Juke (2014 year) - Service and Repair Manual

 

Search            copyright infringement  

 

 

 

 

 

 

 

 

Content      ..     272      273      274     

 

 

 

Nissan Juke (2014 year). Service Repair Manual - part 274

 

 

WW-62

< REMOVAL AND INSTALLATION >

FRONT WIPER BLADE

2.

Pinch the vertebra with tenailles (A) and slide the wiper refill (2)
toward the direction of the arrow 2 to remove.
NOTE:
Be careful not to damage the wiper blade (1).

3.

Insert the new wiper refill kit (2) as shown in the figure to the wiper blade (1) until the stopper at the wiper
refill end fits into the tab on wiper blade.

NOTE:
• Insert the wiper refill to be held securely by tab of wiper blade.
• After the wiper refill is fully inserted, remove the holder (A).
• The refill kit is provided as a set attached to service parts.

4.

After installing the new wiper refill (1) check that the vertebra (2) is well inserted into the wiper refill (1).

NOTE:
Check the following items after replacing wiper refill.
• Wiper refill is not twisted at all.
• Wiper refill thoroughly fits in the tab (B) on wiper blade.
• Wiper refill is inserted from the proper direction.
• The stopper (A) is inserted into the wiper refill. 

JMLIA1737ZZ

JMLIA1738ZZ

JMLIA1734ZZ

Revision: 2013 October

2014 JUKE

FRONT WIPER DRIVE ASSEMBLY

WW-63

< REMOVAL AND INSTALLATION >

C

D

E

F

G

H

I

J

K

M

A

B

WW

N

O

P

FRONT WIPER DRIVE ASSEMBLY

Exploded View

INFOID:0000000009754915

REMOVAL

DISASSEMBLY

1.

Front wiper arm cap

2.

Front wiper arm LH

3.

Front wiper blade LH

4.

Front wiper arm RH

5.

Front wiper blade RH

6.

Front wiper drive assembly

: Pawl

: N·m (kg-m, in-lb)

: N·m (kg-m, ft-lb)

JMLIA1732GB

1.

Front wiper linkage 1

2.

Shaft seal

3.

Front wiper frame

4.

Front wiper motor

5.

Front wiper linkage 2

: Nissan MP special grease No.2

JMLIA1498ZZ

Revision: 2013 October

2014 JUKE

WW-64

< REMOVAL AND INSTALLATION >

FRONT WIPER DRIVE ASSEMBLY

Removal and Installation

INFOID:0000000009754916

REMOVAL

1.

Remove front wiper arms (LH and RH). Refer to 

WW-59, "Removal and Installation"

.

2.

Remove cowl top cover. Refer to 

EXT-26, "Removal and Installation"

.

3.

Disconnect the front wiper motor connector.

4.

Remove the mounting bolts from front wiper drive assembly.

5.

Remove the front wiper drive assembly from the vehicle.

INSTALLATION

1.

Install the front wiper drive assembly to the vehicle.

2.

Connect front wiper motor connector.

3.

Operate front wiper to move it to the auto stop position.

4.

Install cowl top cover. Refer to 

EXT-26, "Removal and Installation"

.

5.

Install front wiper arms. Refer to 

WW-59, "Removal and Installation"

.

Disassembly and Assembly

INFOID:0000000009754917

DISASSEMBLY

1.

Remove the front wiper linkage 1 and 2 from the front wiper drive assembly.

CAUTION:

Never bend the linkage or damage the plastic part of the ball joint when removing the wiper link-
age.

2.

Remove the front wiper motor mounting screws, and then remove the front wiper motor from the front
wiper frame.

ASSEMBLY

1.

Connect the front wiper motor connector.

2.

Operate the front wiper to move it to the auto stop position.

3.

Disconnect the front wiper motor connector.

4.

Install the front wiper motor to the front wiper frame.

5.

Install the front wiper linkage 2 to the front wiper motor and the front wiper frame.

6.

Install the front wiper linkage 1 to the front wiper frame.

CAUTION:

• Never drop front wiper motor or cause it to come into contact with other parts.
• Be careful for the grease condition at the front wiper motor and front wiper linkage joint

(retainer). Apply Multi

purpose grease or an equivalent if necessary.

Revision: 2013 October

2014 JUKE

WIPER AND WASHER SWITCH

WW-65

< REMOVAL AND INSTALLATION >

C

D

E

F

G

H

I

J

K

M

A

B

WW

N

O

P

WIPER AND WASHER SWITCH

Exploded View

INFOID:0000000009754918

Wiper and washer switch is integrated in the combination switch. Refer to 

BCS-91, "Exploded View"

.

Revision: 2013 October

2014 JUKE

WW-66

< REMOVAL AND INSTALLATION >

REAR WIPER ARM

REAR WIPER ARM

Exploded View

INFOID:0000000009754919

Removal and Installation

INFOID:0000000009754920

REMOVAL

1.

Operate rear wiper to the auto stop position.

2.

Remove rear wiper arm cover.

3.

Remove rear wiper arm mounting nut.

4.

Remove wiper arm from the vehicle.

INSTALLATION

1.

Clean wiper arm mount as shown in the figure to prevent nut
from being loosened.

2.

Operate the rear wiper motor to the auto stop position.

3.

Adjust the rear wiper blade position. Refer to 

WW-66, "Adjust-

ment"

.

4.

Install the rear wiper arm by tightening the mounting nut.

5.

Inject the washer fluid.

6.

Operate the rear wiper to the auto stop position.

7.

Check that the rear wiper blades stop at the specified position.

8.

Install the rear wiper arm cover.

Adjustment

INFOID:0000000009754921

REAR WIPER BLADE POSITION ADJUSTMENT

1.

Rear wiper motor

2.

Rear wiper blade

3.

Rear wiper arm

4.

Rear wiper arm cover

5.

Rear wiper pivot seal

A

: Canada models only

: Pawl

: N·m (kg-m, in-lb)

: N·m (kg-m, ft-lb)

JMLIA1503GB

SKIA0082J

Revision: 2013 October

2014 JUKE

REAR WIPER ARM

WW-67

< REMOVAL AND INSTALLATION >

C

D

E

F

G

H

I

J

K

M

A

B

WW

N

O

P

Set the wiper blade top on the defrosting wire (A) (clearance between the end of back door glass and the top
of wiper blade center).

Standard clearance

1.

Rear wiper blade

2.

Back door window glass

3.

Back door panel

A

: Rear defogger wire print

L

: 67.5 

±

 7.5 mm (2.657 

±

 0.295in)

JMLIA1170ZZ

Revision: 2013 October

2014 JUKE

WW-68

< REMOVAL AND INSTALLATION >

REAR WIPER MOTOR

REAR WIPER MOTOR

Exploded View

INFOID:0000000009754922

Removal and Installation

INFOID:0000000009754923

REMOVAL

1.

Remove rear wiper arm. Refer to 

WW-66, "Removal and Installation"

.

2.

Remove back door lower finisher. Refer to 

INT-39, "BACK DOOR SIDE FINISHER : Removal and Installa-

tion"

.

3.

Disconnect rear wiper motor connector.

4.

Remove rear wiper motor mounting bolts.

5.

Remove rear wiper motor from the vehicle.

6.

Remove the pivot seal.

INSTALLATION

Install in the reverse order of removal.

1.

Rear wiper motor

2.

Rear wiper blade

3.

Rear wiper arm

4.

Rear wiper arm cover

5.

Rear wiper pivot seal

A

: Canada models only

: Pawl

: N·m (kg-m, in-lb)

: N·m (kg-m, ft-lb)

JMLIA1503GB

Revision: 2013 October

2014 JUKE

REAR WASHER NOZZLE AND TUBE

WW-69

< REMOVAL AND INSTALLATION >

C

D

E

F

G

H

I

J

K

M

A

B

WW

N

O

P

REAR WASHER NOZZLE AND TUBE

Hydraulic Layout

INFOID:0000000009754924

Removal and Installation

INFOID:0000000009754925

REMOVAL

1.

Remove luggage side upper finisher RH. Refer to 

INT-36, "LUGGAGE SIDE UPPER FINISHER :

Removal and Installation"

.

2.

Disconnect rear washer tube (2) fixing clip and then remove rear
washer tube joint (2) from rear washer tube.

1.

Rear washer nozzle

2.

Plug

3.

Rear washer tube

4.

Joint

5.

Second washer tube

6.

Back door seal rubber

7.

Front washer tube

: Clip

: Pawl

JMLIA1221ZZ

: Clip

JMLIA1222ZZ

Revision: 2013 October

2014 JUKE

WW-70

< REMOVAL AND INSTALLATION >

REAR WASHER NOZZLE AND TUBE

3.

Fully open back door.

4.

Remove back door seal rubber (2), and then remove rear
washer tube (3) from back door seal rubber.

5.

Remove plug (1).

6.

Disengage rear washer nozzle (1) fixing pawl with a flat-bladed
screwdriver (A) and remove the rear washer nozzle.

CAUTION:

Wrap the flat-bladed screwdriver into a protective tape (B)
to protect the part from damage.

7.

Remove rear washer nozzle from the rear washer tube.

INSTALLATION

Install in the reverse order of removal.

Inspection and Adjustment

INFOID:0000000009754926

INSPECTION

Washer Nozzle Inspection

Check that air can pass through the hose by blowing forward (toward
the nozzle), and check that air cannot pass through by sucking.

ADJUSTMENT

Washer Nozzle Spray Position adjustment

JMLIA1223ZZ

JMLIA1224ZZ

JMLIA1171ZZ

Revision: 2013 October

2014 JUKE

REAR WASHER NOZZLE AND TUBE

WW-71

< REMOVAL AND INSTALLATION >

C

D

E

F

G

H

I

J

K

M

A

B

WW

N

O

P

Adjust spray positions to match the positions shown in the figure.

Unit: mm (in)

Insert a needle or similar object (A) into the spray opening (1) and
move up/down and left/right to adjust the spray position.
NOTE:
If wax or dust gets into the spray opening of rear washer nozzle (2),
remove wax or dust with a needle or small pin.

1.

Rear washer nozzle

2.

Black print frame line

L: Length

H : Height

φ

: Spray area

122.8 (4.83)

32.8 (1.29)

30 (1.18)

JMLIA1225ZZ

JMLIA1172ZZ

Revision: 2013 October

2014 JUKE

 

 

 

 

 

 

 

Content      ..     272      273      274