Content .. 265 266 267 268 ..

Nissan Juke (2014 year). Service Repair Manual - part 267

WT-4

< PRECAUTION >

PRECAUTIONS

• ID registration is required when replacing or rotating wheels, replacing tire pressure sensor or BCM. Refer to

WT-24, "Work Procedure"

• Replace grommet seal, valve core and valve cap of tire pressure sensor in TPMS, when replacing each tire

by reaching the wear limit. Refer to

WT-47, "FOR CONTINENTAL TYPE : Exploded View"

(For continental

type),

WT-50, "EXCEPT FOR CONTINENTAL TYPE : Exploded View"

(Except for continental type).

• Because the tire pressure sensor conforms to North America radio law, the following items must be

observed.

- The sensor may be used only in North America.
- It may not be used in any method other than the specified method.
- It must not be disassembled or modified.

Service Notice and Precautions for Road Wheel

INFOID:0000000009753832

• Genuine NISSAN aluminum wheel is designed for each type of vehicle. Use it on the specified vehicle only.
• Use Genuine NISSAN parts for the road wheels, valve caps and wheel nuts.
• Always use them after adjusting the wheel balance. For the balance weights, use Genuine NISSAN alumi-

num wheel weights.

• Use caution when handling the aluminum wheels, because they can be easily scratched. When removing

dirt, do not use any abrasives, a wire brush, or other items that may scratch the coating. Use a neutral deter-
gent if a detergent is needed.

• After driving on roads scattered with anti-icing salts, wash off the wheels completely.
• When installing road wheels onto the vehicle, always wipe off any dirt or foreign substances to prevent them

from being trapped between the contact surfaces of wheel.

• Never apply oil to nut and bolt threads.
• When tightening the valve cap there is a risk of damaging the valve cap if a tool is used. Tighten by hand.

Revision: 2013 October

2014 JUKE

PREPARATION

WT-5

< PREPARATION >

PREPARATION

Special Service Tool

INFOID:0000000009753833

The actual shapes of Kent-Moore tools may differ from those of special service tools illustrated here.

Commercial Service Tool

INFOID:0000000009753834

Tool number
(Kent-Moore No.)
Tool name

Description

—
(J-45295)
Tire pressure sensor activation tool

ID registration

SEIA0462E

Tool name

Description

Power tool

Loosening bolts and nuts

PBIC0190E

Revision: 2013 October

2014 JUKE

WT-6

< SYSTEM DESCRIPTION >

COMPONENT PARTS

SYSTEM DESCRIPTION

COMPONENT PARTS

Component Parts Location

INFOID:0000000009753835

Component Description

INFOID:0000000009753836

ABS actuator and electric unit (control
unit)
Refer to

BRC-9, "Component Parts

Location"

BCM
Refer to

BCS-6, "BODY CONTROL

SYSTEM : Component Parts Loca-
tion"

(With intelligent key system),

BCS-93, "BODY CONTROL SYS-
TEM : Component Parts Location"

(Without intelligent key system).

Remote keyless entry receiver
(tire pressure receiver)

Tire pressure sensor

View with the glove box assembly re-
moved

Wheel

Low tire pressure warning lamp, in-
formation display
(in combination meter)

JSEIA0322ZZ

Component parts

Function

BCM (Body Control Module)

WT-7, "BCM"

Tire pressure sensor

WT-7, "Tire Pressure Sensor"

Tire pressure receiver

WT-7, "Tire Pressure Receiver"

Turn signal lamp

ID registration of each wheel has been completed, turn signal lamp flashes.

Combination meter

Mainly receives the following signals from BCM via CAN communication.
• Low tire pressure warning lamp signal
• TPMS malfunction warning lamp signal

ABS actuator and electric unit (control unit)

Mainly transmits the following signals to BCM via CAN communication.
• Vehicle speed signal (ABS)

Revision: 2013 October

2014 JUKE

COMPONENT PARTS

WT-7

< SYSTEM DESCRIPTION >

BCM

INFOID:0000000009753837

The BCM reads the air pressure signal received by the tire pressure receiver, and controls the low tire pres-
sure warning lamp operation. It also has a judgment function to detect a system malfunction.

Tire Pressure Sensor

INFOID:0000000009753838

The tire pressure sensor integrated with a valve is installed on a wheel, and transmits a detected air pressure
signal by radio wave.

Tire Pressure Receiver

INFOID:0000000009753839

• The tire pressure receiver is incorporated into remote keyless entry receiver.
• The tire pressure receiver receives the air pressure signal transmitted by the tire pressure sensor in each

wheel.

Information Display

INFOID:0000000009753840

The vehicle information display is shown when a low tire pressure warning lamp signal is transmitted from
BCM to combination meter via CAN communication.

Low tire pressure warning lamp

WT-8, "System Description"

Information display

WT-7, "Information Display"

Component parts

Function

Condition

Vehicle information display

Ignition switch OFF

Not indicated

Ignition switch ON

Low tire pressure warning lamp remains ON after blinking for one
minute. [Tire Pressure Monitoring System (TPMS) malfunction.]

Not indicated

Ignition switch ON

Low tire pressure warning lamp remains ON. (low tire pressure)

Indicated

Revision: 2013 October

2014 JUKE

WT-8

< SYSTEM DESCRIPTION >

SYSTEM

SYSTEM

System Description

INFOID:0000000009753841

• During driving, the TPMS (Tire Pressure Monitoring System) receives the signal transmitted from tire pres-

sure sensor installed in each wheel. The BCM (Body Control Module) of this system has pressure judgment
and trouble diagnosis functions. When the tire pressure monitoring system detects low inflation pressure or
another unusual symptom, the low tire pressure warning lamps in the combination meter comes on.

• If the tire pressure is less than the specified value, the low tire pressure warning lamp illuminates that the tire

pressure is less than the specified value.

• Activates the TPMS (Tire Pressure Monitoring System) when the vehicle speed is 40 km/h (25 MPH) or

more.

SYSTEM DIAGRAM

INPUT/OUTPUT SIGNAL

Major signal transmission between each unit via communication lines is shown in the following table.

LOW TIRE PRESSURE WARNING LAMP INDICATION CONDITION

Uses CAN communication from the BCM to illuminate the low tire pressure warning lamp on the combination
meter.

JSEIA0323GB

Component parts

Signal item

Combination meter

Mainly receives the following signals from BCM via CAN communication.
• Low tire pressure warning lamp signal
• TPMS malfunction warning lamp signal

ABS actuator and electric unit (con-
trol unit)

Mainly transmits the following signals to BCM via CAN communication.
• Vehicle speed signal (ABS)

Condition

Low tire pressure warning lamp

Ignition switch OFF

OFF

Ignition switch ON
(system normal)

Warning lamp turns on for 1second, then turns off.

Low tire pressure

Tire pressure sensor ID not registered in BCM

Tire pressure monitoring system malfunction
(Other diagnostic item)

Warning lamp blinks 1 min, then turns on.

Revision: 2013 October

2014 JUKE

DIAGNOSIS SYSTEM (BCM) (WITH INTELLIGENT KEY SYSTEM)

WT-9

< SYSTEM DESCRIPTION >

DIAGNOSIS SYSTEM (BCM) (WITH INTELLIGENT KEY SYSTEM)

COMMON ITEM

COMMON ITEM : CONSULT Function (BCM - COMMON ITEM)

INFOID:0000000009753842

APPLICATION ITEM

CONSULT performs the following functions via CAN communication with BCM.

SYSTEM APPLICATION

BCM can perform the following functions for each system.
NOTE:
It can perform the diagnosis modes except the following for all sub system selection items.

: Applicable item

NOTE:

*: For models with automatic A/C, this diagnosis mode is not used.

FREEZE FRAME DATA (FFD)

The BCM records the following vehicle condition at the time a particular DTC is detected, and displays on
CONSULT.

Diagnosis mode

Function Description

Work Support

Changes the setting for each system function.

Self Diagnostic Result

Displays the diagnosis results judged by BCM.

CAN Diag Support Monitor

Monitors the reception status of CAN communication viewed from BCM.

Data Monitor

The BCM input/output signals are displayed.

Active Test

The signals used to activate each device are forcibly supplied from BCM.

Ecu Identification

The BCM part number is displayed.

Configuration

• Read and save the vehicle specification.
• Write the vehicle specification when replacing BCM.

System

Sub system selection item

Diagnosis mode

Work Support

Data Monitor

Active Test

Door lock

DOOR LOCK

Rear window defogger

REAR DEFOGGER

Warning chime

BUZZER

Interior room lamp timer

INT LAMP

Exterior lamp

HEAD LAMP

Wiper and washer

WIPER

Turn signal and hazard warning lamps

FLASHER

Air conditioning system

AIR CONDITONER

• Intelligent Key system
• Engine start system

INTELLIGENT KEY

Combination switch

COMB SW

Body control system

BCM

NVIS - NATS

IMMU

Interior room lamp battery saver

BATTERY SAVER

Back door open

TRUNK

Theft warning alarm

THEFT ALM

RAP

RETAINED PWR

Signal buffer system

SIGNAL BUFFER

TPMS

AIR PRESSURE MONITOR

Revision: 2013 October

2014 JUKE

WT-10

< SYSTEM DESCRIPTION >

DIAGNOSIS SYSTEM (BCM) (WITH INTELLIGENT KEY SYSTEM)

NOTE:

*: Power position shifts to “LOCK” from “OFF”, when ignition switch is in the OFF position, selector lever is in the P position (A/T models
and CVT models), and any of the following conditions are met.

• Closing door

• Opening door

• Door is locked using door request switch

• Door is locked using Intelligent Key

The power position shifts to “ACC” when the push-button ignition switch (push switch) is pushed at “LOCK”.

AIR PRESSURE MONITOR

AIR PRESSURE MONITOR : CONSULT Function (BCM - AIR PRESSURE MONI-
TOR)

INFOID:0000000009753843

APPLICATION ITEM

CONSULT performs the following functions via CAN communication with BCM.

CONSULT screen item

Indication/Unit

Description

Vehicle Speed

km/h

Vehicle speed of the moment a particular DTC is detected

Odo/Trip Meter

Total mileage (Odometer value) of the moment a particular DTC is detected

Vehicle Condition

SLEEP>LOCK

Power position status of
the moment a particular
DTC is detected

While turning BCM status from low power consumption mode to
normal mode (Power position is “LOCK”*.)

SLEEP>OFF

While turning BCM status from low power consumption mode to
normal mode (Power position is “OFF”.)

LOCK>ACC

While turning power position from “LOCK”* *to “ACC”

ACC>ON

While turning power position from “ACC” to “IGN”

RUN>ACC

While turning power position from “RUN” to “ACC” (Vehicle is
stopping and selector lever is except P position.)

CRANK>RUN

While turning power position from “CRANKING” to “RUN” (From
cranking up the engine to run it)

RUN>URGENT

While turning power position from “RUN“ to “ACC” (Emergency
stop operation)

ACC>OFF

While turning power position from “ACC” to “OFF”

OFF>LOCK

While turning power position from “OFF” to “LOCK”*

OFF>ACC

While turning power position from “OFF” to “ACC”

ON>CRANK

While turning power position from “IGN” to “CRANKING”

OFF>SLEEP

While turning BCM status from normal mode (Power position is
“OFF”.) to low power consumption mode

LOCK>SLEEP

While turning BCM status from normal mode (Power position is
“LOCK”*.) to low power consumption mode

LOCK

Power position is “LOCK”*

OFF

Power position is “OFF” (Ignition switch OFF)

ACC

Power position is “ACC” (Ignition switch ACC)

Power position is “IGN” (Ignition switch ON with engine stopped)

ENGINE RUN

Power position is “RUN” (Ignition switch ON with engine running)

CRANKING

Power position is “CRANKING” (At engine cranking)

IGN Counter

0 - 39

The number of times that ignition switch is turned ON after DTC is detected
• The number is 0 when a malfunction is detected now.
• The number increases like 1

→

3...38

→

39 after returning to the normal condition

whenever ignition switch OFF

→

ON.

• The number is fixed to 39 until the self-diagnosis results are erased if it is over 39.

Revision: 2013 October

2014 JUKE

DIAGNOSIS SYSTEM (BCM) (WITH INTELLIGENT KEY SYSTEM)

WT-11

< SYSTEM DESCRIPTION >

SELF DIAGNOSTIC RESULT

Refer to

BCS-59, "DTC Index"

DATA MONITOR MODE

NOTE:
The following table includes information (items) inapplicable to this vehicle. For information (items) applicable
to this vehicle, refer to CONSULT display items.

ACTIVE TEST MODE

NOTE:
After completing the work below, perform an active test.
1.

Check ID registration state and perform self-diagnosis.

Erase the self-diagnosis result history.

WORK SUPPORT

Diagnosis mode

Function Description

Self Diagnostic Result

Displays the diagnosis results judged by BCM.

Data Monitor

The BCM input/output signals are displayed.

Active Test

The signals used to activate each device are forcibly supplied from BCM.

Work Support

Components can be quickly and accurately adjusted.

Monitor item (Unit)

Remarks

AIR PRESS FL
(kPa, kg/cm2 or Psi)

Tire pressure

AIR PRESS FR
(kPa, kg/cm2 or Psi)

AIR PRESS RR
(kPa, kg/cm2 or Psi)

AIR PRESS RL
(kPa, kg/cm2 or Psi)

ID REGST FL1
(Yet, Done)

Registration ID

ID REGST FR1
(Yet, Done)

ID REGST RR1
(Yet, Done)

ID REGST RL1
(Yet, Done)

WARNING LAMP
(On/Off)

Low tire pressure warning lamp

BUZZER
(On/Off)

NOTE:
This item is displayed, but cannot be use this item.

Item

Description

WARNING LAMP

Low tire pressure warning lamp can be turned ON arbitrarily.

ID REGIST WARNING

NOTE:
Displayed but not used in TPMS.

RUN FLAT TIRE W/L

NOTE:
Displayed but not used in TPMS.

RUN FLAT/T WARN BUZZER

NOTE:
Displayed but not used in TPMS.

FLASHER

Turn signal lamps can be turned ON arbitrarily.

HORN

This test is able to check to check that the horn sounds.

Revision: 2013 October

2014 JUKE

WT-12

< SYSTEM DESCRIPTION >

DIAGNOSIS SYSTEM (BCM) (WITH INTELLIGENT KEY SYSTEM)

Item

Description

ID READ

Registered tire pressure sensor ID can be displayed.

ID REGIST

Tire pressure sensor ID can be registered.

Revision: 2013 October

2014 JUKE

DIAGNOSIS SYSTEM (BCM) (WITHOUT INTELLIGENT KEY SYSTEM)

WT-13

< SYSTEM DESCRIPTION >

DIAGNOSIS SYSTEM (BCM) (WITHOUT INTELLIGENT KEY SYSTEM)

COMMON ITEM

COMMON ITEM : CONSULT Function (BCM - COMMON ITEM)

INFOID:0000000009753844

APPLICATION ITEM

CONSULT performs the following functions via CAN communication with BCM.

SYSTEM APPLICATION

BCM can perform the following functions for each system.
NOTE:
It can perform the diagnosis modes except the following for all sub system selection items.

: Applicable item

AIR PRESSURE MONITOR

AIR PRESSURE MONITOR : CONSULT Function (BCM - AIR PRESSURE MONI-

Diagnosis mode

Function Description

Work Support

Changes the setting for each system function.

Self Diagnostic Result

Displays the diagnosis results judged by BCM.

CAN Diag Support Monitor

Monitors the reception status of CAN communication viewed from BCM.

Data Monitor

The BCM input/output signals are displayed.

Active Test

The signals used to activate each device are forcibly supplied from BCM.

Ecu Identification

The BCM part number is displayed.

Configuration

• Read and save the vehicle specification.
• Write the vehicle specification when replacing BCM.

System

Sub system selection item

Diagnosis mode

Work Support

Data Monitor

Active Test

Door lock

DOOR LOCK

Rear window defogger

REAR DEFOGGER

Warning chime

BUZZER

Interior room lamp control

INT LAMP

Remote keyless entry system

MULTI REMOTE ENT

Exterior lamp

HEAD LAMP

Wiper and washer

WIPER

Turn signal and hazard warning lamps

FLASHER

Air conditioning system

AIR CONDITONER

Combination switch

COMB SW

Body control system

BCM

NATS

IMMU

Interior room lamp battery saver

BATTERY SAVER

Back door open

TRUNK

Theft warning alarm

THEFT ALM

RAP system

RETAINED PWR

Signal buffer system

SIGNAL BUFFER

Panic alarm

PANIC ALARM

TPMS

AIR PRESSUE MONITOR

Revision: 2013 October

2014 JUKE

WT-14

< SYSTEM DESCRIPTION >

DIAGNOSIS SYSTEM (BCM) (WITHOUT INTELLIGENT KEY SYSTEM)

TOR)

INFOID:0000000009753845

APPLICATION ITEM

CONSULT performs the following functions via CAN communication with BCM.

SELF DIAGNOSTIC RESULT

Refer to

BCS-132, "DTC Index"

DATA MONITOR MODE

NOTE:
The following table includes information (items) inapplicable to this vehicle. For information (items) applicable
to this vehicle, refer to CONSULT display items.

ACTIVE TEST MODE

NOTE:
After completing the work below, perform an active test.
1.

Check ID registration state and perform self-diagnosis.

Erase the self-diagnosis result history.

Diagnosis mode

Function Description

Self Diagnostic Result

Displays the diagnosis results judged by BCM.

Data Monitor

The BCM input/output signals are displayed.

Active Test

The signals used to activate each device are forcibly supplied from BCM.

Work Support

Components can be quickly and accurately adjusted.

Monitor item (Unit)

Remarks

AIR PRESS FL
(kPa, kg/cm2 or Psi)

Tire pressure

AIR PRESS FR
(kPa, kg/cm2 or Psi)

AIR PRESS RR
(kPa, kg/cm2 or Psi)

AIR PRESS RL
(kPa, kg/cm2 or Psi)

ID REGST FL1
(Yet, Done)

Registration ID

ID REGST FR1
(Yet, Done)

ID REGST RR1
(Yet, Done)

ID REGST RL1
(Yet, Done)

WARNING LAMP
(On/Off)

Low tire pressure warning lamp

BUZZER
(On/Off)

NOTE:
This item is displayed, but cannot be use this item.

Item

Description

WARNING LAMP

Low tire pressure warning lamp can be turned ON arbitrarily.

ID REGIST WARNING

NOTE:
Displayed but not used in TPMS.

RUN FLAT TIRE W/L

NOTE:
Displayed but not used in TPMS.

Revision: 2013 October

2014 JUKE

DIAGNOSIS SYSTEM (BCM) (WITHOUT INTELLIGENT KEY SYSTEM)

WT-15

< SYSTEM DESCRIPTION >

WORK SUPPORT

FLASHER

Turn signal lamps can be turned ON arbitrarily.

RUN FLAT TIRE W/R

NOTE:
Displayed but not used in TPMS.

Item

Description

Item

Description

ID READ

Registered tire pressure sensor ID can be displayed.

ID REGIST

Tire pressure sensor ID can be registered.

Revision: 2013 October

2014 JUKE

WT-16

< ECU DIAGNOSIS INFORMATION >

BCM

ECU DIAGNOSIS INFORMATION

BCM

WITH INTELLIGENT KEY

WITH INTELLIGENT KEY : List of ECU Reference

INFOID:0000000009753846

WITHOUT INTELLIGENT KEY

WITHOUT INTELLIGENT KEY : List of ECU Reference

INFOID:0000000009753847

ECU

Reference

BCM

BCS-36, "Reference Value"

BCS-57, "Fail-safe"

BCS-58, "DTC Inspection Priority Chart"

BCS-59, "DTC Index"

ECU

Reference

BCM

BCS-118, "Reference Value"

BCS-131, "Fail-safe"

BCS-132, "DTC Inspection Priority Chart"

BCS-132, "DTC Index"

Revision: 2013 October

2014 JUKE

TIRE PRESSURE MONITORING SYSTEM

WT-17

< WIRING DIAGRAM >

WIRING DIAGRAM

TIRE PRESSURE MONITORING SYSTEM

Wiring Diagram

INFOID:0000000009753848

JREWC0616GB

Revision: 2013 October

2014 JUKE

WT-18

< WIRING DIAGRAM >

TIRE PRESSURE MONITORING SYSTEM

JREWC0617GB

Revision: 2013 October

2014 JUKE

TIRE PRESSURE MONITORING SYSTEM

WT-19

< WIRING DIAGRAM >

JREWC0618GB

Revision: 2013 October

2014 JUKE

Content .. 265 266 267 268 ..