Content .. 258 259 260 261 ..

Nissan Juke (2014 year). Service Repair Manual - part 260

CVT FLUID

TM-305

< PERIODIC MAINTENANCE >

[CVT: RE0F10B]

PERIODIC MAINTENANCE

CVT FLUID

Inspection

INFOID:0000000009752651

CHECKING CVT FLUID

The fluid level should be checked with the fluid warmed up to 50 to 80

C (122 to 176

F). The fluid level check

procedure is as follows:
1.

Check for fluid leakage.

With the engine warmed up, drive the vehicle in an urban area.
When ambient temperature is 20

C (68

F), it takes about 10

minutes for the CVT fluid to warm up to 50 to 80

C (122 to

176

F).

Park the vehicle on a level surface.

Apply parking brake firmly.

With engine at idle, while depressing brake pedal, move shift
selector throughout the entire shift range.

Pull out the CVT fluid level gauge from the CVT fluid charging
pipe after pressing the tab on the CVT fluid level gauge to
release the lock.

Wipe fluid off the CVT fluid level gauge. Insert the CVT fluid
level gauge rotating 180

from the originally installed position,

then securely push the CVT fluid level gauge until it meets the
top end of the CVT fluid charging pipe.

CAUTION:

When wiping away the CVT fluid level gauge, always use
lint-free paper, not a cloth rag.

Place the selector lever in “P” or “N” and check that the fluid
level is within the specified range.

CAUTION:

When reinstalling CVT fluid level gauge, insert it into the
CVT fluid charging pipe and rotate it to the original installa-
tion position until securely locked.

CVT FLUID CONDITION

SMA146B

SCIA1933E

SCIA1931E

SCIA1932E

Revision: 2013 October

2014 JUKE

TM-306

< PERIODIC MAINTENANCE >

[CVT: RE0F10B]

CVT FLUID

Check CVT fluid condition.
• If CVT fluid is very dark or smells burned, check operation of CVT.

Flush cooling system after repair of CVT.

• If CVT fluid contains frictional material (clutches, brakes, etc.),

replace radiator and flush cooler line using cleaning solvent and
compressed air after repair of CVT. Refer to

TM-216, "Cleaning"

Changing

INFOID:0000000009752652

CAUTION:

Replace drain plug gasket with new ones at the final stage of the operation when installing.

Remove drain plug from oil pan.

Remove drain plug gasket from drain plug.

Install drain plug gasket to drain plug.

CAUTION:

Never reuse drain plug gasket.

Install drain plug to oil pan.

Fill CVT fluid from CVT fluid charging pipe to the specified level.

CAUTION:

• Use only recommended CVT fluid. Never mix with other fluid.
• Using CVT fluid other than recommended CVT fluid will deteriorate in driveability and CVT dura-

bility, and may damage the CVT, which is not covered by the warranty.

• When filling CVT fluid, take care not to scatter heat generating parts such as exhaust.
• Sufficiently shake the container of CVT fluid before using.
• Delete CVT fluid deterioration date with CONSULT after changing CVT fluid.

With the engine warmed up, drive the vehicle in an urban area.
NOTE:
When ambient temperature is 20

C (68

F), it takes about 10 minutes for the CVT fluid to warm up to 50 to

C (122 to 176

F).

Check CVT fluid level and condition.

Repeat steps 1 to 5 if CVT fluid has been contaminated.

Select “Data Monitor” in “TRANSMISSION” using CONSULT.

10. Select “CONFORM CVTF DETERIORTN”.

11. Select “Erase”.

Fluid status

Conceivable cause

Required operation

Varnished (viscous
varnish state)

CVT fluid become
degraded due to
high temperatures.

Replace the CVT fluid and check the
CVT main unit and the vehicle for
malfunctions (wire harnesses, cool-
er pipes, etc.)

Milky white or
cloudy

Water in the fluid

Replace the CVT fluid and check for
places where water is getting in.

Large amount of
metal powder mixed
in

Unusual wear of
sliding parts within
CVT

Replace the CVT fluid and check for
improper operation of the CVT.

ATA0022D

Drain plug – tightening torque

: Refer to

TM-322, "Exploded View"

Recommended fluid and fluid capacity

: Refer to

MA-10, "Fluids and Lubricants"

Revision: 2013 October

2014 JUKE

CVT SHIFT SELECTOR

TM-307

< REMOVAL AND INSTALLATION >

[CVT: RE0F10B]

REMOVAL AND INSTALLATION

CVT SHIFT SELECTOR

Exploded View

INFOID:0000000009752653

Removal and Installation

INFOID:0000000009752654

REMOVAL

CAUTION:

Always apply the parking brake before performing removal and installation.

Disconnect battery cable from negative terminal. Refer to

PG-99, "Removal and Installation"

Shift the selector lever to “N” position.

Remove the center console. Refer to

IP-24, "Removal and Installation"

Disconnect the CVT shift selector connector.

Shift the selector lever to “P” position.

Remove the key interlock cable from the CVT shift selector assembly. Refer to

TM-316, "Removal and

Installation"

(Without push starter system).

Remove the control cable from the CVT shift selector assembly. Refer to

TM-311, "Removal and Installa-

tion"

Remove the CVT shift selector assembly.

INSTALLATION

Note the following, and install in the reverse order of removal.

Selector lever knob

Lock pin

Knob cover

Position indication panel

CVT shift selector assembly

Shift lock unit

Key interlock rod*

Position indicator bulb

:N·m (kg-m, in-lb)

*: Without push engine starter

JSDIA2341GB

Revision: 2013 October

2014 JUKE

TM-308

< REMOVAL AND INSTALLATION >

[CVT: RE0F10B]

CVT SHIFT SELECTOR

• When connecting the control cable (1) to the CVT shift selector

assembly (2), face the grooved surface of the rib (A) up and insert
the control cable until it stops.

Disassembly and Assembly

INFOID:0000000009752655

DISASSEMBLY

Slide the selector lever knob cover (1) down.

CAUTION:

Never damage the knob cover.

Pull out the lock pin (2).

Pull the selector lever knob (3) and knob cover upwards to
remove them.

Remove the position lamp.

Disengage the hooks (A) (4 locations), and lift up the position
indication panel (1) to separate it from the CVT shift selector
assembly (2).

CAUTION:

Never damage the CVT shift selector assembly.

Remove the shift lock unit from the CVT shift selector assembly.

Disconnect the park position switch connector, detent switch
connector, and shift lock solenoid connector from the shift lock
unit.

ASSEMBLY

Note the following, and assemble in the reverse order of disassembly.
• Follow the procedure below and place the selector knob onto the CVT shift selector.
1.

Install the lock pin (2) onto the selector lever knob (3).

Install the knob cover (1) onto the selector lever knob.

Press the selector lever knob onto the selector lever until it
clicks.

CAUTION:

• When pressing the selector lever knob onto the selector

lever, never press the selector lever knob button.

• Never strike the selector lever knob to press it into place.

Inspection

INFOID:0000000009752656

INSPECTION AFTER INSTALLATION

• Check the CVT position. If a malfunction is found, adjust the CVT position. Refer to

TM-226, "Inspection and

Adjustment"

JSDIA1624ZZ

JSDIA2401ZZ

JSDIA1802ZZ

JSDIA2401ZZ

Revision: 2013 October

2014 JUKE

CVT SHIFT SELECTOR

TM-309

< REMOVAL AND INSTALLATION >

[CVT: RE0F10B]

• The key can be removed only when the selector lever is in the “P” position. (With key interlock)
• It must not be possible to turn the ignition switch to LOCK when the selector lever is not in the “P” position.

(With key interlock)

Revision: 2013 October

2014 JUKE

TM-310

< REMOVAL AND INSTALLATION >

[CVT: RE0F10B]

CONTROL CABLE

CONTROL CABLE

Exploded View

INFOID:0000000009752657

2WD MODELS

AWD MODELS

Bracket B

Lock plate

Bracket A

Transaxle assembly

Control cable

CVT shift selector assembly

Manual lever

Grommet

: N·m (kg-m, ft-lb)

: N·m (kg-m, in-lb)

JSDIA2352GB

Revision: 2013 October

2014 JUKE

CONTROL CABLE

TM-311

< REMOVAL AND INSTALLATION >

[CVT: RE0F10B]

Removal and Installation

INFOID:0000000009752658

REMOVAL

CAUTION:

Always apply the parking brake before performing removal and installation.

Remove the battery. Refer to

PG-99, "Removal and Installation"

Remove the control cable from the CVT shift selector assembly. Refer to

TM-307, "Removal and Installa-

tion"

Disengage the pawls (B) of the grommet (A), and pull down-
wards to remove.

Remove the control cable installation nut from the manual lever.

Lock plate

Bracket A

Transaxle assembly

Control cable

Bracket B

CVT shift selector assembly

Manual lever

Grommet

: N·m (kg-m, ft-lb)

: N·m (kg-m, in-lb)

JSDIA2353GB

JSDIA1809ZZ

Revision: 2013 October

2014 JUKE

TM-312

< REMOVAL AND INSTALLATION >

[CVT: RE0F10B]

CONTROL CABLE

Remove the lock plate (1).

Remove center muffler from the mounting rubber and lower the
center muffler downward. Refer to

EX-8, "Removal and Installa-

tion"

Lift up the heat plate.

Remove the control cable (1) from the bracket (2).

Remove the control cable from the vehicle.

10. Remove bracket.

INSTALLATION

Note the following, and install in the reverse order of removal.
• From below the vehicle, press the grommet (A) into place until the

pawls (B) make a click sound.

CAUTION:

• Place the grommet on the floor, then fasten it in place from

below the vehicle.

• Check that pulling down on the grommet does not discon-

nect it.

• Pay attention to the following when connecting the control cable to the CVT shift selector.
1.

When connecting the control cable (1) to the CVT shift selector
assembly (2), face the grooved surface of the rib (A) up and
insert the control cable until it stops.

JSDIA2643ZZ

:Vehicle front

JPDIA0107ZZ

JSDIA1809ZZ

JSDIA1624ZZ

Revision: 2013 October

2014 JUKE

CONTROL CABLE

TM-313

< REMOVAL AND INSTALLATION >

[CVT: RE0F10B]

Install the socket (A) onto the CVT shift selector.

CAUTION:

• Place the socket onto the CVT shift lever, then fasten it in

place from above.

• Check that the pulling on the socket does not disconnect

it.

Inspection

INFOID:0000000009752659

INSPECTION AFTER INSTALLATION

Check the CVT position. If a malfunction is found, adjust the CVT position. Refer to

TM-226, "Inspection and

Adjustment"

JSDIA1810ZZ

Revision: 2013 October

2014 JUKE

TM-314

< REMOVAL AND INSTALLATION >

[CVT: RE0F10B]

PADDLE SHIFTER

PADDLE SHIFTER

Exploded View

INFOID:0000000010198376

Removal and Installation

INFOID:0000000010198377

REMOVAL

Park the vehicle on a level surface.

Remove the driver air bag module. Refer to

SR-11, "Removal and Installation"

Remove the steering wheel. Refer to

ST-9, "Removal and Installation"

Remove the column cover. Refer to

IP-13, "Removal and Installation"

Steering column assembly

Paddle shifter (shift-down switch)

Paddle shifter (shift-up switch)

: N·m (kg-m, in-lb)

AWDIA0557GB

Revision: 2013 October

2014 JUKE

PADDLE SHIFTER

TM-315

< REMOVAL AND INSTALLATION >

[CVT: RE0F10B]

Remove the paddle shifter connector (C) and (D) from paddle
shifter.

Remove the paddle shifter mounting bolts (E) and nuts (F).

Remove the paddle shifter from the steering column assembly.

INSTALLATION

Installation is in the reverse order of removal.

: Side of paddle shifter (shift-down switch)

: Side of paddle shifter (shift-up switch)

AWDIA0563ZZ

Revision: 2013 October

2014 JUKE

TM-316

< REMOVAL AND INSTALLATION >

[CVT: RE0F10B]

KEY INTERLOCK CABLE

KEY INTERLOCK CABLE

Exploded View

INFOID:0000000009752660

Removal and Installation

INFOID:0000000009752661

REMOVAL

CAUTION:

Always apply the parking brake before performing removal and installation.

Shift the selector lever to the “N” position.

Remove the selector lever knob. Refer to

TM-308, "Disassembly and Assembly"

Shift the selector lever to the “P” position.

Remove the center console. Refer to

IP-24, "Removal and Installation"

Press the pawls (B) of the key interlock cable slider (A) while
sliding it in the direction of the casing cap (C), and separate the
adjusting holder (D) and slider.

Remove the key interlock cable from the CVT shift selector.

Remove the steering column lower cover and driver instrument
lower panel. Refer to

IP-13, "Removal and Installation"

CVT shift selector assembly

Key interlock cable

Key cylinder

Clip

JSDIA2448ZZ

:Key interlock rod

JSDIA1797ZZ

Revision: 2013 October

2014 JUKE

KEY INTERLOCK CABLE

TM-317

< REMOVAL AND INSTALLATION >

[CVT: RE0F10B]

Lift clip (A) in the direction of the arrow (

C) and remove in the

direction of the arrow (

D).

Disconnect the key interlock cable from the key cylinder.

10. Disengage the clip and disconnect the key interlock cable from

the vehicle.

INSTALLATION

Note the following, and install in the reverse order of removal.
• Install the adjusting holder (A) onto the key interlock rod (B), then

install the casing cap (C) onto the CVT shift selector cable bracket
(D).

CAUTION:

• When installing the key interlock cable, never bend or twist

the cable forcefully.

• After connecting the key interlock cable to the CVT shift

selector cable bracket, be sure to check that the casing cap
is completely fastened to the cable bracket. If the casing cap
is easily displaced, replace the key interlock cable.

• While pressing the detent rod (B) down, slide the key interlock

cable slider (A) toward the key interlock rod (D) side, and install the
adjusting holder (C) and key interlock rod.

CAUTION:

• Never squeeze the pawls on the key interlock cable slider

when holding the slider.

• Never apply force in a perpendicular direction to the key

interlock rod when sliding the slider.

Inspection

INFOID:0000000009752662

INSPECTION AFTER INSTALLATION

• Check the CVT position. If a malfunction is found, adjust the CVT position. Refer to

TM-226, "Inspection and

Adjustment"

• The key can be removed only when the selector lever is in the “P” position.
• It must not be possible to turn the ignition switch to LOCK when the selector lever is not in the “P” position.

:Key interlock cable

:Key cylinder

JSDIA1798ZZ

JSDIA1799ZZ

JSDIA1800ZZ

Revision: 2013 October

2014 JUKE