Nissan Juke (2014 year). Service Repair Manual

SRC-152

< DTC/CIRCUIT DIAGNOSIS >

B1218, B1219, B1220, B1221, B1222, B1223 DIAGNOSIS SENSOR UNIT

B1218, B1219, B1220, B1221, B1222, B1223 DIAGNOSIS SENSOR UNIT

DTC Logic

INFOID:0000000009751860

DTC DETECTION LOGIC

DTC CONFIRMATION PROCEDURE

CHECK SELF-DIAG RESULT

With CONSULT

Turn ignition switch ON.

Perform “Self Diagnostic Result” mode of “AIR BAG” using CONSULT.

Without CONSULT

Turn ignition switch ON.

Check the air bag warning lamp status. Refer to

SRC-12, "On Board Diagnosis Function"

NOTE:
SRS does not enter the diagnosis mode if no malfunction is detected in the user mode.

Is malfunctioning part detected?

YES

>> Refer to

SRC-152, "Diagnosis Procedure"

>> INSPECTION END

Diagnosis Procedure

INFOID:0000000009751861

WARNING:

• Before servicing, turn ignition switch OFF, disconnect battery negative terminal, and wait at least 3

minutes or more. (To discharge backup capacitor.)

• Never use unspecified tester or other measuring device.

CHECK HARNESS CONNECTOR

Check the harness connector.

Is the inspection result normal?

YES

>> GO TO 2.

>> Replace harness connectors.

CHECK WIRING HARNESS

Check the wiring harness externals.
Is the inspection result normal?

YES

>> GO TO 3.

>> Replace wiring harness.

REPLACE AIR BAG DIAGNOSIS SENSOR UNIT

Replace air bag diagnosis sensor unit. Refer to

SR-28, "Removal and Installation"

Perform DTC confirmation procedure. Refer to

SRC-152, "DTC Logic"

Is DTC detected?

YES

>> GO TO 1.

>> INSPECTION END

DTC

Display contents of

CONSULT

DTC detecting condition

Possible cause

B1218
B1219
B1220
B1221
B1222
B1223

CONTROL UNIT

Air bag diagnosis sensor unit is malfunctioning

Malfunction in air bag diagnosis sensor unit

Revision: 2013 October

2014 JUKE

B1234, B1235, B1236, B1237, B1238, B1239 DIAGNOSIS SENSOR UNIT

SRC-153

< DTC/CIRCUIT DIAGNOSIS >

SRC

B1234, B1235, B1236, B1237, B1238, B1239 DIAGNOSIS SENSOR UNIT

DTC Logic

INFOID:0000000009751862

DTC DETECTION LOGIC

DTC CONFIRMATION PROCEDURE

CHECK SELF-DIAG RESULT

With CONSULT

Turn ignition switch ON.

Perform “Self Diagnostic Result” mode of “AIR BAG” using CONSULT.

Without CONSULT

Turn ignition switch ON.

Check the air bag warning lamp status. Refer to

SRC-12, "On Board Diagnosis Function"

NOTE:
SRS does not enter the diagnosis mode if no malfunction is detected in the user mode.

Is malfunctioning part detected?

YES

>> Refer to

SRC-153, "Diagnosis Procedure"

>> INSPECTION END

Diagnosis Procedure

INFOID:0000000009751863

WARNING:

• Before servicing, turn ignition switch OFF, disconnect battery negative terminal, and wait at least 3

minutes or more. (To discharge backup capacitor.)

• Never use unspecified tester or other measuring device.

CHECK HARNESS CONNECTOR

Check the harness connector.

Is the inspection result normal?

YES

>> GO TO 2.

>> Replace harness connectors.

CHECK WIRING HARNESS

Check the wiring harness externals.
Is the inspection result normal?

YES

>> GO TO 3.

>> Replace wiring harness.

REPLACE AIR BAG DIAGNOSIS SENSOR UNIT

Replace air bag diagnosis sensor unit. Refer to

SR-28, "Removal and Installation"

Perform DTC confirmation procedure. Refer to

SRC-153, "DTC Logic"

Is DTC detected?

YES

>> GO TO 1.

>> INSPECTION END

DTC

Display contents of

CONSULT

DTC detecting condition

Possible cause

B1234
B1235
B1236
B1237
B1238
B1239

CONTROL UNIT

Air bag diagnosis sensor unit is malfunctioning

Malfunction in air bag diagnosis sensor unit

Revision: 2013 October

2014 JUKE

SRC-154

< DTC/CIRCUIT DIAGNOSIS >

B1336, B1337 SATELLITE SENSOR RH

B1336, B1337 SATELLITE SENSOR RH

DTC Logic

INFOID:0000000009751864

DTC DETECTION LOGIC

DTC CONFIRMATION PROCEDURE

CHECK SELF-DIAG RESULT

With CONSULT

Turn ignition switch ON.

Perform “Self Diagnostic Result” mode of “AIR BAG” using CONSULT.

Without CONSULT

Turn ignition switch ON.

Check the air bag warning lamp status. Refer to

SRC-12, "On Board Diagnosis Function"

NOTE:
SRS does not enter the diagnosis mode if no malfunction is detected in the user mode.

Is malfunctioning part detected?

YES

>> Refer to

SRC-154, "Diagnosis Procedure"

>> INSPECTION END

Diagnosis Procedure

INFOID:0000000009751865

WARNING:

• Before servicing, turn ignition switch OFF, disconnect battery negative terminal, and wait at least 3

minutes or more. (To discharge backup capacitor.)

• Never use unspecified tester or other measuring device.

CHECK HARNESS CONNECTOR

Check the harness connector.

Is the inspection result normal?

YES

>> GO TO 2.

>> Replace harness connector.

CHECK WIRING HARNESS

Check the wiring harness externals.

Is the inspection result normal?

YES

>> GO TO 3.

>> Replace wiring harness.

REPLACE FRONT DOOR SATELLITE SENSOR

Replace front door satellite sensor RH. Refer to

SR-25, "Removal and Installation"

Perform DTC confirmation procedure. Refer to

SRC-154, "DTC Logic"

Is DTC detected?

YES

>> GO TO 4.

>> INSPECTION END

REPLACE AIR BAG DIAGNOSIS SENSOR UNIT

Replace air bag diagnosis sensor unit. Refer to

SR-28, "Removal and Installation"

Perform DTC confirmation procedure. Refer to

SRC-154, "DTC Logic"

Is DTC detected?

DTC

Display contents of CON-

SULT

DTC detecting condition

Possible cause

B1336
B1337

FR-RH DOOR SATEL
SENS
[SENSOR MALFUNC-
TION]

Front door satellite sensor RH is malfunc-
tioning

• Harness or connectors
• Malfunction in front door satellite sensor RH
• Malfunction in air bag diagnosis sensor unit

Revision: 2013 October

2014 JUKE

SRC-156

< DTC/CIRCUIT DIAGNOSIS >

B1338, B1340, B1341, B1342 SATELLITE SENSOR RH

B1338, B1340, B1341, B1342 SATELLITE SENSOR RH

DTC Logic

INFOID:0000000009751866

DTC DETECTION LOGIC

DTC CONFIRMATION PROCEDURE

CHECK SELF-DIAG RESULT

With CONSULT

Turn ignition switch ON.

Perform “Self Diagnostic Result” mode of “AIR BAG” using CONSULT.

Without CONSULT

Turn ignition switch ON.

Check the air bag warning lamp status. Refer to

SRC-12, "On Board Diagnosis Function"

NOTE:
SRS does not enter the diagnosis mode if no malfunction is detected in the user mode.

Is malfunctioning part detected?

YES

>> Refer to

SRC-156, "Diagnosis Procedure"

>> INSPECTION END

Diagnosis Procedure

INFOID:0000000009751867

WARNING:

• Before servicing, turn ignition switch OFF, disconnect battery negative terminal, and wait at least 3

minutes or more. (To discharge backup capacitor.)

• Never use unspecified tester or other measuring device.

CHECK HARNESS CONNECTOR

Check the harness connector.

Is the inspection result normal?

YES

>> GO TO 2.

>> Replace harness connector.

CHECK WIRING HARNESS

Check the wiring harness externals.

Is the inspection result normal?

YES

>> GO TO 3.

>> Replace wiring harness.

REPLACE FRONT DOOR SATELLITE SENSOR

Replace front door satellite sensor RH. Refer to

SR-25, "Removal and Installation"

Perform DTC confirmation procedure. Refer to

SRC-156, "DTC Logic"

Is DTC detected?

YES

>> GO TO 4.

>> INSPECTION END

REPLACE AIR BAG DIAGNOSIS SENSOR UNIT

Replace air bag diagnosis sensor unit. Refer to

SR-28, "Removal and Installation"

Perform DTC confirmation procedure. Refer to

SRC-156, "DTC Logic"

Is DTC detected?

DTC

Display contents of

CONSULT

DTC detecting condition

Possible cause

B1338
B1340
B1341
B1342

FR-RH DOOR SATEL
SENS
[COMM MALFUNC-
TION]

Front door satellite sensor RH is malfunc-
tioning

• Harness or connectors
• Malfunction in front door satellite sensor RH
• Malfunction in air bag diagnosis sensor unit

Revision: 2013 October

2014 JUKE

SRC-158

< DTC/CIRCUIT DIAGNOSIS >

B1339 SATELLITE SENSOR RH

B1339 SATELLITE SENSOR RH

DTC Logic

INFOID:0000000009751868

DTC DETECTION LOGIC

DTC CONFIRMATION PROCEDURE

CHECK SELF-DIAG RESULT

With CONSULT

Turn ignition switch ON.

Perform “Self Diagnostic Result” mode of “AIR BAG” using CONSULT.

Without CONSULT

Turn ignition switch ON.

Check the air bag warning lamp status. Refer to

SRC-12, "On Board Diagnosis Function"

NOTE:
SRS does not enter the diagnosis mode if no malfunction is detected in the user mode.

Is malfunctioning part detected?

YES

>> Refer to

SRC-158, "Diagnosis Procedure"

>> INSPECTION END

Diagnosis Procedure

INFOID:0000000009751869

WARNING:

• Before servicing, turn ignition switch OFF, disconnect battery negative terminal, and wait at least 3

minutes or more. (To discharge backup capacitor.)

• Never use unspecified tester or other measuring device.

REPLACE FRONT DOOR SATELLITE SENSOR

Replace front door satellite sensor RH. Refer to

SR-25, "Removal and Installation"

Perform DTC confirmation procedure. Refer to

SRC-158, "DTC Logic"

Is DTC detected?

YES

>> GO TO 2.

>> INSPECTION END

REPLACE AIR BAG DIAGNOSIS SENSOR UNIT

Replace air bag diagnosis sensor unit. Refer to

SR-28, "Removal and Installation"

Perform DTC confirmation procedure. Refer to

SRC-158, "DTC Logic"

Is DTC detected?

YES

>> GO TO 1.

>> INSPECTION END

DTC

Display contents of

CONSULT

DTC detecting condition

Possible cause

B1339

FR-RH DOOR SATEL
SENS
[MIS-INSTALLATION]

Front door satellite sensor RH is out of the
specified specification

Diagnosis sensor unit or front door satellite sen-
sor RH is different from the part specified

Revision: 2013 October

2014 JUKE

B1343, B1344 SATELLITE SENSOR LH

SRC-159

< DTC/CIRCUIT DIAGNOSIS >

SRC

B1343, B1344 SATELLITE SENSOR LH

DTC Logic

INFOID:0000000009751870

DTC DETECTION LOGIC

DTC CONFIRMATION PROCEDURE

CHECK SELF-DIAG RESULT

With CONSULT

Turn ignition switch ON.

Perform “Self Diagnostic Result” mode of “AIR BAG” using CONSULT.

Without CONSULT

Turn ignition switch ON.

Check the air bag warning lamp status. Refer to

SRC-12, "On Board Diagnosis Function"

NOTE:
SRS does not enter the diagnosis mode if no malfunction is detected in the user mode.

Is malfunctioning part detected?

YES

>> Refer to

SRC-159, "Diagnosis Procedure"

>> INSPECTION END

Diagnosis Procedure

INFOID:0000000009751871

WARNING:

• Before servicing, turn ignition switch OFF, disconnect battery negative terminal, and wait at least 3

minutes or more. (To discharge backup capacitor.)

• Never use unspecified tester or other measuring device.

CHECK HARNESS CONNECTOR

Check the harness connector.

Is the inspection result normal?

YES

>> GO TO 2.

>> Replace harness connector.

CHECK WIRING HARNESS

Check the wiring harness externals.

Is the inspection result normal?

YES

>> GO TO 3.

>> Replace wiring harness.

REPLACE FRONT DOOR SATELLITE SENSOR

Replace front door satellite sensor LH. Refer to

SR-25, "Removal and Installation"

Perform DTC confirmation procedure. Refer to

SRC-159, "DTC Logic"

Is DTC detected?

YES

>> GO TO 4.

>> INSPECTION END

REPLACE AIR BAG DIAGNOSIS SENSOR UNIT

Replace air bag diagnosis sensor unit. Refer to

SR-28, "Removal and Installation"

Perform DTC confirmation procedure. Refer to

SRC-159, "DTC Logic"

Is DTC detected?

DTC

Display contents of

CONSULT

DTC detecting condition

Possible cause

B1343
B1344

FR-LH DOOR SATEL
SENS
[SENSOR MALFUNC-
TION]

Front door satellite sensor LH is malfunc-
tioning

• Harness or connectors
• Malfunction in front door satellite sensor LH
• Malfunction in air bag diagnosis sensor unit

Revision: 2013 October

2014 JUKE

B1345, B1347, B1348, B1349 SATELLITE SENSOR LH

SRC-161

< DTC/CIRCUIT DIAGNOSIS >

SRC

B1345, B1347, B1348, B1349 SATELLITE SENSOR LH

DTC Logic

INFOID:0000000009751872

DTC DETECTION LOGIC

DTC CONFIRMATION PROCEDURE

CHECK SELF-DIAG RESULT

With CONSULT

Turn ignition switch ON.

Perform “Self Diagnostic Result” mode of “AIR BAG” using CONSULT.

Without CONSULT

Turn ignition switch ON.

Check the air bag warning lamp status. Refer to

SRC-12, "On Board Diagnosis Function"

NOTE:
SRS does not enter the diagnosis mode if no malfunction is detected in the user mode.
Is malfunctioning part detected?

YES

>> Refer to

SRC-164, "Diagnosis Procedure"

>> INSPECTION END

Diagnosis Procedure

INFOID:0000000009751873

WARNING:

• Before servicing, turn ignition switch OFF, disconnect battery negative terminal, and wait at least 3

minutes or more. (To discharge backup capacitor.)

• Never use unspecified tester or other measuring device.

CHECK HARNESS CONNECTOR

Check the harness connector.
Is the inspection result normal?

YES

>> GO TO 2.

>> Replace harness connector.

CHECK WIRING HARNESS

Check the wiring harness externals.

Is the inspection result normal?

YES

>> GO TO 3.

>> Replace wiring harness.

REPLACE SATELLITE SENSOR

Replace front door satellite sensor LH. Refer to

SR-25, "Removal and Installation"

Perform DTC confirmation procedure. Refer to

SRC-164, "DTC Logic"

Is DTC detected?

YES

>> GO TO 4.

>> INSPECTION END

REPLACE AIR BAG DIAGNOSIS SENSOR UNIT

Replace air bag diagnosis sensor unit. Refer to

SR-28, "Removal and Installation"

Perform DTC confirmation procedure. Refer to

SRC-164, "DTC Logic"

Is DTC detected?

DTC

Display contents of

CONSULT

DTC detecting condition

Possible cause

B1345
B1347
B1348
B1349

FR-LH DOOR SATEL
SENS
[COMM MALFUNC-
TION]

Front door satellite sensor LH is malfunc-
tioning

• Harness or connectors
• Malfunction in front door satellite sensor LH
• Malfunction in air bag diagnosis sensor unit

Revision: 2013 October

2014 JUKE

B1346 SATELLITE SENSOR LH

SRC-163

< DTC/CIRCUIT DIAGNOSIS >

SRC

B1346 SATELLITE SENSOR LH

DTC Logic

INFOID:0000000009751874

DTC DETECTION LOGIC

DTC CONFIRMATION PROCEDURE

CHECK SELF-DIAG RESULT

With CONSULT

Turn ignition switch ON.

Perform “Self Diagnostic Result” mode of “AIR BAG” using CONSULT.

Without CONSULT

Turn ignition switch ON.

Check the air bag warning lamp status. Refer to

SRC-12, "On Board Diagnosis Function"

NOTE:
SRS does not enter the diagnosis mode if no malfunction is detected in the user mode.

Is malfunctioning part detected?

YES

>> Refer to

SRC-163, "Diagnosis Procedure"

>> INSPECTION END

Diagnosis Procedure

INFOID:0000000009751875

WARNING:

• Before servicing, turn ignition switch OFF, disconnect battery negative terminal, and wait at least 3

minutes or more. (To discharge backup capacitor.)

• Never use unspecified tester or other measuring device.

REPLACE FRONT DOOR SATELLITE SENSOR

Replace front door satellite sensor LH. Refer to

SR-25, "Removal and Installation"

Perform DTC confirmation procedure. Refer to

SRC-163, "DTC Logic"

Is DTC detected?

YES

>> GO TO 2.

>> INSPECTION END

REPLACE AIR BAG DIAGNOSIS SENSOR UNIT

Replace air bag diagnosis sensor unit. Refer to

SR-28, "Removal and Installation"

Perform DTC confirmation procedure. Refer to

SRC-163, "DTC Logic"

Is DTC detected?

YES

>> GO TO 1.

>> INSPECTION END

DTC

Display contents of

CONSULT

DTC detecting condition

Possible cause

B1346

FR-LH DOOR SATEL
SENS
[MIS-INSTALLATION]

Front door satellite sensor LH is out of the
specified specification

Diagnosis sensor unit or front door satellite sen-
sor LH is different from the part specified

Revision: 2013 October

2014 JUKE

SRC-164

< DTC/CIRCUIT DIAGNOSIS >

B1350, B1351 SATELLITE SENSOR

B1350, B1351 SATELLITE SENSOR

DTC Logic

INFOID:0000000009751876

DTC DETECTION LOGIC

DTC CONFIRMATION PROCEDURE

CHECK SELF-DIAG RESULT

With CONSULT

Turn ignition switch ON.

Perform “Self Diagnostic Result” mode of “AIR BAG” using CONSULT.

Without CONSULT

Turn ignition switch ON.

Check the air bag warning lamp status. Refer to

SRC-12, "On Board Diagnosis Function"

NOTE:
SRS does not enter the diagnosis mode if no malfunction is detected in the user mode.

Is malfunctioning part detected?

YES

>> Refer to

SRC-164, "Diagnosis Procedure"

>> INSPECTION END

Diagnosis Procedure

INFOID:0000000009751877

WARNING:

• Before servicing, turn ignition switch OFF, disconnect battery negative terminal, and wait at least 3

minutes or more. (To discharge backup capacitor.)

• Never use unspecified tester or other measuring device.

REPLACE BOTH OF FRONT DOOR SATELLITE SENSOR

Replace both of front door satellite sensor. Refer to

SR-25, "Removal and Installation"

Perform DTC confirmation procedure. Refer to

SRC-164, "DTC Logic"

Is DTC detected?

YES

>> GO TO 2.

>> INSPECTION END

REPLACE AIR BAG DIAGNOSIS SENSOR UNIT

Replace air bag diagnosis sensor unit. Refer to

SR-28, "Removal and Installation"

Perform DTC confirmation procedure. Refer to

SRC-164, "DTC Logic"

Is DTC detected?

YES

>> GO TO 1.

>> INSPECTION END

DTC

Display contents of

CONSULT

DTC detecting condition

Possible cause

B1350
B1351

FR DOOR SATEL SENS

Front door satellite sensor is malfunction-
ing or out of the specified specification

• Malfunction in front door satellite sensor LH/RH
• Malfunction in air bag diagnosis sensor unit

Revision: 2013 October

2014 JUKE

SRS AIR BAG WARNING LAMP DOES NOT TURN OFF

SRC-165

< SYMPTOM DIAGNOSIS >

SRC

SYMPTOM DIAGNOSIS

SRS AIR BAG WARNING LAMP DOES NOT TURN OFF

Diagnosis Procedure

INFOID:0000000009751878

CHECK AIR BAG MODULE AND SEAT BELT PRE-TENSIONER

Check the deployment of air bag module and seat belt pre-tensioner.

Is air bag module deployed?

YES

>> Replace the malfunctioning parts.

>> GO TO 2.

CHECK AIR BAG FUSE

Check 10 A fuse [No.2, located in fuse block (J/B)].

Is the inspection result normal?

YES

>> GO TO 3.

>> Replace the fuse.

CHECK HARNESS CONNECTOR

Check the harness connector.

Is the inspection result normal?

YES

>> GO TO 4.

>> Replace harness connectors.

CHECK WIRING HARNESS

Check the wiring harness externals.
Is the inspection result normal?

YES

>> GO TO 5.

>> Replace wiring harness.

REPLACE AIR BAG DIAGNOSIS SENSOR UNIT

Replace air bag diagnosis sensor unit. Refer to

SR-28, "Removal and Installation"

Check air bag warning lamp operation.

Is the inspection result normal?

YES

>> INSPECTION END

>> GO TO 6.

REPLACE COMBINATION METER

Replace combination meter. Refer to

MWI-61, "Removal and Installation"

Check air bag warning lamp operation.

Is the inspection result normal?

YES

>> INSPECTION END

>> GO TO 1.

Revision: 2013 October

2014 JUKE

SRC-166

< SYMPTOM DIAGNOSIS >

SRS AIR BAG WARNING LAMP DOES NOT TURN ON

SRS AIR BAG WARNING LAMP DOES NOT TURN ON

Diagnosis Procedure

INFOID:0000000009751879

CHECK COMBINATION METER POWER SUPPLY AND GROUND CIRCUIT

Check combination meter unit power supply and ground circuit. Refer to

MWI-50, "COMBINATION METER :

Diagnosis Procedure"

Is the inspection result normal?

YES

>> GO TO 2.

>> Repair or replace the malfunctioning parts.

CHECK HARNESS CONNECTOR

Check the harness connector.

Is the inspection result normal?

YES

>> GO TO 3.

>> Replace harness connectors.

CHECK WIRING HARNESS

Check the wiring harness externals.
Is the inspection result normal?

YES

>> GO TO 4.

>> Replace wiring harness.

CHECK AIR BAG DIAGNOSIS SENSOR UNIT

Disconnect air bag diagnosis sensor unit connector and turn ignition switch ON.

Does air bag warning lamp turn ON?

YES

>> Replace air bag diagnosis sensor unit. Refer to

SR-28, "Removal and Installation"

>> Replace combination meter. Refer to

MWI-61, "Removal and Installation"

Revision: 2013 October

2014 JUKE

Nissan Juke (2014 year). Service Repair Manual - part 234