Nissan Juke (2014 year). Service Repair Manual - part 231

 

  Index      Manuals     Nissan Juke (2014 year) - Service and Repair Manual

 

Search            copyright infringement  

 

 

 

 

 

 

 

 

Content      ..     229      230      231      232     ..

 

 

Nissan Juke (2014 year). Service Repair Manual - part 231

 

 

B1118, B1119 SATELLITE SENSOR LH

SRC-103

< DTC/CIRCUIT DIAGNOSIS >

C

D

E

F

G

I

J

K

L

M

A

B

SRC

N

O

P

NO

>> INSPECTION END

Revision: 2013 October

2014 JUKE

SRC-104

< DTC/CIRCUIT DIAGNOSIS >

B1120 SATELLITE SENSOR LH

B1120 SATELLITE SENSOR LH

DTC Logic

INFOID:0000000009751800

DTC DETECTION LOGIC

DTC CONFIRMATION PROCEDURE

1.

CHECK SELF-DIAG RESULT

 With CONSULT

1.

Turn ignition switch ON.

2.

Perform “Self Diagnostic Result” mode of “AIR BAG” using CONSULT.

 Without CONSULT

1.

Turn ignition switch ON.

2.

Check the air bag warning lamp status. Refer to 

SRC-12, "On Board Diagnosis Function"

.

NOTE:
SRS does not enter the diagnosis mode if no malfunction is detected in the user mode.

Is malfunctioning part detected?

YES

>> Refer to 

SRC-104, "Diagnosis Procedure"

.

NO

>> INSPECTION END

Diagnosis Procedure

INFOID:0000000009751801

WARNING:

• Before servicing, turn ignition switch OFF, disconnect battery negative terminal, and wait at least 3

minutes or more. (To discharge backup capacitor.)

• Never use unspecified tester or other measuring device. 

1.

CHECK HARNESS CONNECTOR

Check the harness connector.

Is the inspection result normal?

YES

>> GO TO 2.

NO

>> Replace harness connector.

2.

CHECK WIRING HARNESS

Check the wiring harness externals.

Is the inspection result normal?

YES

>> GO TO 3. 

NO

>> Replace wiring harness.

3.

REPLACE SATELLITE SENSOR

1.

Replace satellite sensor LH. Refer to 

SR-25, "Removal and Installation"

.

2.

Perform DTC confirmation procedure. Refer to 

SRC-104, "DTC Logic"

.

Is DTC detected?

YES

>> GO TO 4. 

NO

>> INSPECTION END

4.

REPLACE AIR BAG DIAGNOSIS SENSOR UNIT

1.

Replace air bag diagnosis sensor unit. Refer to 

SR-28, "Removal and Installation"

.

2.

Perform DTC confirmation procedure. Refer to 

SRC-104, "DTC Logic"

.

Is DTC detected?

YES

>> GO TO 1. 

DTC

Display contents of 

CONSULT

DTC detecting condition

Possible cause

B1120

SATELLITE SENS LH 
[COMM FAIL]

Satellite sensor LH is malfunctioning or out 
of the specified specification

• Harness or connectors
• Malfunction in satellite sensor LH
• Malfunction in air bag diagnosis sensor unit

Revision: 2013 October

2014 JUKE

B1120 SATELLITE SENSOR LH

SRC-105

< DTC/CIRCUIT DIAGNOSIS >

C

D

E

F

G

I

J

K

L

M

A

B

SRC

N

O

P

NO

>> INSPECTION END

Revision: 2013 October

2014 JUKE

SRC-106

< DTC/CIRCUIT DIAGNOSIS >

B1121 SATELLITE SENSOR LH

B1121 SATELLITE SENSOR LH

DTC Logic

INFOID:0000000009751802

DTC DETECTION LOGIC

DTC CONFIRMATION PROCEDURE

1.

CHECK SELF-DIAG RESULT

 With CONSULT

1.

Turn ignition switch ON.

2.

Perform “Self Diagnostic Result” mode of “AIR BAG” using CONSULT.

 Without CONSULT

1.

Turn ignition switch ON.

2.

Check the air bag warning lamp status. Refer to 

SRC-12, "On Board Diagnosis Function"

.

NOTE:
SRS does not enter the diagnosis mode if no malfunction is detected in the user mode.

Is malfunctioning part detected?

YES

>> Refer to 

SRC-106, "Diagnosis Procedure"

.

NO

>> INSPECTION END

Diagnosis Procedure

INFOID:0000000009751803

WARNING:

• Before servicing, turn ignition switch OFF, disconnect battery negative terminal, and wait at least 3

minutes or more. (To discharge backup capacitor.)

• Never use unspecified tester or other measuring device. 

1.

CHECK HARNESS CONNECTOR

Check the harness connector.

Is the inspection result normal?

YES

>> GO TO 2.

NO

>> Replace harness connector.

2.

CHECK WIRING HARNESS

Check the wiring harness externals.

Is the inspection result normal?

YES

>> GO TO 3. 

NO

>> Replace wiring harness.

3.

REPLACE SATELLITE SENSOR

1.

Replace satellite sensor LH. Refer to 

SR-25, "Removal and Installation"

.

2.

Perform DTC confirmation procedure. Refer to 

SRC-106, "DTC Logic"

.

Is DTC detected?

YES

>> GO TO 4. 

NO

>> INSPECTION END

4.

REPLACE AIR BAG DIAGNOSIS SENSOR UNIT

1.

Replace air bag diagnosis sensor unit. Refer to 

SR-28, "Removal and Installation"

.

2.

Perform DTC confirmation procedure. Refer to 

SRC-106, "DTC Logic"

.

Is DTC detected?

YES

>> GO TO 1. 

NO

>> INSPECTION END

DTC

Display contents of 

CONSULT

DTC detecting condition

Possible cause

B1121

SATELLITE SENS LH 
[UNMATCH]

Satellite sensor LH is out of the specified 
specification

Diagnosis sensor unit or satellite sensor RH is dif-
ferent from the part specified

Revision: 2013 October

2014 JUKE

B1122, B1123, B1124, B1125, B1126, B1127 DIAGNOSIS SENSOR UNIT

SRC-107

< DTC/CIRCUIT DIAGNOSIS >

C

D

E

F

G

I

J

K

L

M

A

B

SRC

N

O

P

B1122, B1123, B1124, B1125, B1126, B1127 DIAGNOSIS SENSOR UNIT

DTC Logic

INFOID:0000000009751804

DTC DETECTION LOGIC

DTC CONFIRMATION PROCEDURE

1.

CHECK SELF-DIAG RESULT

 With CONSULT

1.

Turn ignition switch ON.

2.

Perform “Self Diagnostic Result” mode of “AIR BAG” using CONSULT.

 Without CONSULT

1.

Turn ignition switch ON.

2.

Check the air bag warning lamp status. Refer to 

SRC-12, "On Board Diagnosis Function"

.

NOTE:
SRS does not enter the diagnosis mode if no malfunction is detected in the user mode.

Is malfunctioning part detected?

YES

>> Refer to 

SRC-107, "Diagnosis Procedure"

.

NO

>> INSPECTION END

Diagnosis Procedure

INFOID:0000000009751805

WARNING:

• Before servicing, turn ignition switch OFF, disconnect battery negative terminal, and wait at least 3

minutes or more. (To discharge backup capacitor.)

• Never use unspecified tester or other measuring device. 

1.

CHECK HARNESS CONNECTOR

Check the harness connector.

Is the inspection result normal?

YES

>> GO TO 2.

NO

>> Replace harness connectors.

2.

CHECK WIRING HARNESS

Check the wiring harness externals.

Is the inspection result normal?

YES

>> GO TO 3.

NO

>> Replace wiring harness.

3.

REPLACE AIR BAG DIAGNOSIS SENSOR UNIT

1.

Replace air bag diagnosis sensor unit. Refer to 

SR-28, "Removal and Installation"

.

2.

Perform DTC confirmation procedure. Refer to 

SRC-107, "DTC Logic"

.

Is DTC detected?

YES

>> GO TO 1. 

NO

>> INSPECTION END

DTC

Display contents of 

CONSULT

DTC detecting condition

Possible cause

B1122
B1123
B1124
B1125
B1126
B1127

CONTROL UNIT 

Air bag diagnosis sensor unit is malfunctioning

Malfunction in air bag diagnosis sensor unit

Revision: 2013 October

2014 JUKE

SRC-108

< DTC/CIRCUIT DIAGNOSIS >

B1129 SIDE AIR BAG MODULE RH

B1129 SIDE AIR BAG MODULE RH

DTC Logic

INFOID:0000000009751806

DTC DETECTION LOGIC

DTC CONFIRMATION PROCEDURE

1.

CHECK SELF-DIAG RESULT

 With CONSULT

1.

Turn ignition switch ON.

2.

Perform “Self Diagnostic Result” mode of “AIR BAG” using CONSULT.

 Without CONSULT

1.

Turn ignition switch ON.

2.

Check the air bag warning lamp status.

SRC-12, "On Board Diagnosis Function"

 

NOTE:
SRS does not enter the diagnosis mode if no malfunction is detected in the user mode.
Is malfunctioning part detected?

YES

>> Refer to 

SRC-108, "Diagnosis Procedure"

.

NO

>> INSPECTION END

Diagnosis Procedure

INFOID:0000000009751807

WARNING:

• Before servicing, turn ignition switch OFF, disconnect battery negative terminal, and wait at least 3

minutes or more. (To discharge backup capacitor.)

• Never use unspecified tester or other measuring device. 

1.

CHECK HARNESS CONNECTOR

Check the harness connector.
Is the inspection result normal?

YES

>> GO TO 2.

NO

>> Replace harness connector.

2.

CHECK WIRING HARNESS

Check the wiring harness externals.

Is the inspection result normal?

YES

>> GO TO 3. 

NO

>> Replace wiring harness.

3.

REPLACE AIR BAG DIAGNOSIS SENSOR UNIT

1.

Replace air bag diagnosis sensor unit. Refer to 

SR-28, "Removal and Installation"

.

2.

Perform DTC confirmation procedure. Refer to 

SRC-108, "DTC Logic"

.

Is DTC detected?

YES

>> GO TO 4. 

NO

>> INSPECTION END

4.

REPLACE SIDE AIR BAG MODULE

1.

Replace side air bag module RH. Refer to 

SE-20, "SEATBACK : Disassembly and Assembly"

.

2.

Perform DTC confirmation procedure. Refer to 

SRC-108, "DTC Logic"

.

Is DTC detected?

DTC

Display contents of 

CONSULT

DTC detecting condition

Possible cause

B1129

SIDE MODULE RH
[OPEN]

Side air bag module RH circuit is open

• Harness or connectors

(The module circuit is open.)

• Malfunction in side air bag module RH
• Malfunction in air bag diagnosis sensor unit

Revision: 2013 October

2014 JUKE

B1129 SIDE AIR BAG MODULE RH

SRC-109

< DTC/CIRCUIT DIAGNOSIS >

C

D

E

F

G

I

J

K

L

M

A

B

SRC

N

O

P

YES

>> GO TO 1. 

NO

>> INSPECTION END

Revision: 2013 October

2014 JUKE

SRC-110

< DTC/CIRCUIT DIAGNOSIS >

B1130 SIDE AIR BAG MODULE RH

B1130 SIDE AIR BAG MODULE RH

DTC Logic

INFOID:0000000009751808

DTC DETECTION LOGIC

DTC CONFIRMATION PROCEDURE

1.

CHECK SELF-DIAG RESULT

 With CONSULT

1.

Turn ignition switch ON.

2.

Perform “Self Diagnostic Result” mode of “AIR BAG” using CONSULT.

 Without CONSULT

1.

Turn ignition switch ON.

2.

Check the air bag warning lamp status. Refer to 

SRC-12, "On Board Diagnosis Function"

.

NOTE:
SRS does not enter the diagnosis mode if no malfunction is detected in the user mode.

Is malfunctioning part detected?

YES

>> Refer to 

SRC-110, "Diagnosis Procedure"

.

NO

>> INSPECTION END

Diagnosis Procedure

INFOID:0000000009751809

WARNING:

• Before servicing, turn ignition switch OFF, disconnect battery negative terminal, and wait at least 3

minutes or more. (To discharge backup capacitor.)

• Never use unspecified tester or other measuring device. 

1.

CHECK HARNESS CONNECTOR

Check the harness connector.

Is the inspection result normal?

YES

>> GO TO 2.

NO

>> Replace harness connector.

2.

CHECK WIRING HARNESS

Check the wiring harness externals.

Is the inspection result normal?

YES

>> GO TO 3. 

NO

>> Replace wiring harness.

3.

REPLACE AIR BAG DIAGNOSIS SENSOR UNIT

1.

Replace air bag diagnosis sensor unit. Refer to 

SR-28, "Removal and Installation"

.

2.

Perform DTC confirmation procedure. Refer to 

SRC-110, "DTC Logic"

.

Is DTC detected?

YES

>> GO TO 4. 

NO

>> INSPECTION END

4.

REPLACE SIDE AIR BAG MODULE

1.

Replace side air bag module RH. Refer to 

SE-20, "SEATBACK : Disassembly and Assembly"

.

2.

Perform DTC confirmation procedure. Refer to 

SRC-110, "DTC Logic"

.

Is DTC detected?

DTC

Display contents of 

CONSULT

DTC detecting condition

Possible cause

B1130

SIDE MODULE RH 
[VB-SHORT]

Side air bag module RH circuit is shorted 
to power supply circuit

• Harness or connectors

(The module circuit is shorted.)

• Malfunction in side air bag module RH
• Malfunction in air bag diagnosis sensor unit

Revision: 2013 October

2014 JUKE

B1130 SIDE AIR BAG MODULE RH

SRC-111

< DTC/CIRCUIT DIAGNOSIS >

C

D

E

F

G

I

J

K

L

M

A

B

SRC

N

O

P

YES

>> GO TO 1. 

NO

>> INSPECTION END

Revision: 2013 October

2014 JUKE

SRC-112

< DTC/CIRCUIT DIAGNOSIS >

B1131 SIDE AIR BAG MODULE RH

B1131 SIDE AIR BAG MODULE RH

DTC Logic

INFOID:0000000009751810

DTC DETECTION LOGIC

DTC CONFIRMATION PROCEDURE

1.

CHECK SELF-DIAG RESULT

 With CONSULT

1.

Turn ignition switch ON.

2.

Perform “Self Diagnostic Result” mode of “AIR BAG” using CONSULT.

 Without CONSULT

1.

Turn ignition switch ON.

2.

Check the air bag warning lamp status. Refer to 

SRC-12, "On Board Diagnosis Function"

.

NOTE:
SRS does not enter the diagnosis mode if no malfunction is detected in the user mode.

Is malfunctioning part detected?

YES

>> Refer to 

SRC-112, "Diagnosis Procedure"

.

NO

>> INSPECTION END

Diagnosis Procedure

INFOID:0000000009751811

WARNING:

• Before servicing, turn ignition switch OFF, disconnect battery negative terminal, and wait at least 3

minutes or more. (To discharge backup capacitor.)

• Never use unspecified tester or other measuring device. 

1.

CHECK HARNESS CONNECTOR

Check the harness connector.

Is the inspection result normal?

YES

>> GO TO 2.

NO

>> Replace harness connector.

2.

CHECK WIRING HARNESS

Check the wiring harness externals.

Is the inspection result normal?

YES

>> GO TO 3. 

NO

>> Replace wiring harness.

3.

REPLACE AIR BAG DIAGNOSIS SENSOR UNIT

1.

Replace air bag diagnosis sensor unit. Refer to 

SR-28, "Removal and Installation"

.

2.

Perform DTC confirmation procedure. Refer to 

SRC-112, "DTC Logic"

.

Is DTC detected?

YES

>> GO TO 4. 

NO

>> INSPECTION END

4.

REPLACE SIDE AIR BAG MODULE

1.

Replace side air bag module RH. Refer to 

SE-20, "SEATBACK : Disassembly and Assembly"

.

2.

Perform DTC confirmation procedure. Refer to 

SRC-112, "DTC Logic"

.

Is DTC detected?

DTC

Display contents of 

CONSULT

DTC detecting condition

Possible cause

B1131

SIDE MODULE RH 
[GND-SHORT]

Side air bag module RH circuit is shorted 
to ground

• Harness or connectors

(The module circuit is shorted.)

• Malfunction in side air bag module RH
• Malfunction in air bag diagnosis sensor unit

Revision: 2013 October

2014 JUKE

B1131 SIDE AIR BAG MODULE RH

SRC-113

< DTC/CIRCUIT DIAGNOSIS >

C

D

E

F

G

I

J

K

L

M

A

B

SRC

N

O

P

YES

>> GO TO 1. 

NO

>> INSPECTION END

Revision: 2013 October

2014 JUKE

SRC-114

< DTC/CIRCUIT DIAGNOSIS >

B1132 SIDE AIR BAG MODULE RH

B1132 SIDE AIR BAG MODULE RH

DTC Logic

INFOID:0000000009751812

DTC DETECTION LOGIC

DTC CONFIRMATION PROCEDURE

1.

CHECK SELF-DIAG RESULT

 With CONSULT

1.

Turn ignition switch ON.

2.

Perform “Self Diagnostic Result” mode of “AIR BAG” using CONSULT.

 Without CONSULT

1.

Turn ignition switch ON.

2.

Check the air bag warning lamp status. Refer to 

SRC-12, "On Board Diagnosis Function"

.

NOTE:
SRS does not enter the diagnosis mode if no malfunction is detected in the user mode.
Is malfunctioning part detected?

YES

>> Refer to 

SRC-114, "Diagnosis Procedure"

.

NO

>> INSPECTION END

Diagnosis Procedure

INFOID:0000000009751813

WARNING:

• Before servicing, turn ignition switch OFF, disconnect battery negative terminal, and wait at least 3

minutes or more. (To discharge backup capacitor.)

• Never use unspecified tester or other measuring device.

1.

CHECK HARNESS CONNECTOR

Check the harness connector.
Is the inspection result normal?

YES

>> GO TO 2.

NO

>> Replace harness connector.

2.

CHECK WIRING HARNESS

Check the wiring harness externals.

Is the inspection result normal?

YES

>> GO TO 3. 

NO

>> Replace wiring harness.

3.

REPLACE AIR BAG DIAGNOSIS SENSOR UNIT

1.

Replace air bag diagnosis sensor unit. Refer to 

SR-28, "Removal and Installation"

.

2.

Perform DTC confirmation procedure. Refer to 

SRC-114, "DTC Logic"

.

Is DTC detected?

YES

>> GO TO 4. 

NO

>> INSPECTION END

4.

REPLACE SIDE AIR BAG MODULE

1.

Replace side air bag module RH. Refer to 

SE-20, "SEATBACK : Disassembly and Assembly"

.

2.

Perform DTC confirmation procedure. Refer to 

SRC-114, "DTC Logic"

.

Is DTC detected?

DTC

Display contents of 

CONSULT

DTC detecting condition

Possible cause

B1132

SIDE MODULE RH 
[SHORT]

Side air bag module RH circuits are short-
ed to each other

• Harness or connectors

(The module circuit is shorted.)

• Malfunction in side air bag module RH
• Malfunction in air bag diagnosis sensor unit

Revision: 2013 October

2014 JUKE

B1132 SIDE AIR BAG MODULE RH

SRC-115

< DTC/CIRCUIT DIAGNOSIS >

C

D

E

F

G

I

J

K

L

M

A

B

SRC

N

O

P

YES

>> GO TO 1. 

NO

>> INSPECTION END

Revision: 2013 October

2014 JUKE

SRC-116

< DTC/CIRCUIT DIAGNOSIS >

B1134 SIDE AIR BAG MODULE LH

B1134 SIDE AIR BAG MODULE LH

DTC Logic

INFOID:0000000009751814

DTC DETECTION LOGIC

DTC CONFIRMATION PROCEDURE

1.

CHECK SELF-DIAG RESULT

 With CONSULT

1.

Turn ignition switch ON.

2.

Perform “Self Diagnostic Result” mode of “AIR BAG” using CONSULT.

 Without CONSULT

1.

Turn ignition switch ON.

2.

Check the air bag warning lamp status. Refer to 

SRC-12, "On Board Diagnosis Function"

.

NOTE:
SRS does not enter the diagnosis mode if no malfunction is detected in the user mode.

Is malfunctioning part detected?

YES

>> Refer to 

SRC-116, "Diagnosis Procedure"

.

NO

>> INSPECTION END

Diagnosis Procedure

INFOID:0000000009751815

WARNING:

• Before servicing, turn ignition switch OFF, disconnect battery negative terminal, and wait at least 3

minutes or more. (To discharge backup capacitor.)

• Never use unspecified tester or other measuring device. 

1.

CHECK HARNESS CONNECTOR

Check the harness connector.

Is the inspection result normal?

YES

>> GO TO 2.

NO

>> Replace harness connector.

2.

CHECK WIRING HARNESS

Check the wiring harness externals.

Is the inspection result normal?

YES

>> GO TO 3. 

NO

>> Replace wiring harness.

3.

REPLACE AIR BAG DIAGNOSIS SENSOR UNIT

1.

Replace air bag diagnosis sensor unit. Refer to 

SR-28, "Removal and Installation"

.

2.

Perform DTC confirmation procedure. Refer to 

SRC-116, "DTC Logic"

.

Is DTC detected?

YES

>> GO TO 4. 

NO

>> INSPECTION END

4.

REPLACE SIDE AIR BAG MODULE

1.

Replace side air bag module LH. Refer to 

SE-20, "SEATBACK : Disassembly and Assembly"

.

2.

Perform DTC confirmation procedure. Refer to 

SRC-116, "DTC Logic"

.

Is DTC detected?

DTC

Display contents of CON-

SULT

DTC detecting condition

Possible cause

B1134

SIDE MODULE LH 
[OPEN]

Side air bag module LH circuit is open

• Harness or connectors

(The module circuit is open.)

• Malfunction in side air bag module LH
• Malfunction in air bag diagnosis sensor unit

Revision: 2013 October

2014 JUKE

B1134 SIDE AIR BAG MODULE LH

SRC-117

< DTC/CIRCUIT DIAGNOSIS >

C

D

E

F

G

I

J

K

L

M

A

B

SRC

N

O

P

YES

>> GO TO 1. 

NO

>> INSPECTION END

Revision: 2013 October

2014 JUKE

SRC-118

< DTC/CIRCUIT DIAGNOSIS >

B1135 SIDE AIR BAG MODULE LH

B1135 SIDE AIR BAG MODULE LH

DTC Logic

INFOID:0000000009751816

DTC DETECTION LOGIC

DTC CONFIRMATION PROCEDURE

1.

CHECK SELF-DIAG RESULT

 With CONSULT

1.

Turn ignition switch ON.

2.

Perform “Self Diagnostic Result” mode of “AIR BAG” using CONSULT.

 Without CONSULT

1.

Turn ignition switch ON.

2.

Check the air bag warning lamp status. Refer to 

SRC-12, "On Board Diagnosis Function"

.

NOTE:
SRS does not enter the diagnosis mode if no malfunction is detected in the user mode.

Is malfunctioning part detected?

YES

>> Refer to 

SRC-118, "Diagnosis Procedure"

.

NO

>> INSPECTION END

Diagnosis Procedure

INFOID:0000000009751817

WARNING:

• Before servicing, turn ignition switch OFF, disconnect battery negative terminal, and wait at least 3

minutes or more. (To discharge backup capacitor.)

• Never use unspecified tester or other measuring device.

1.

CHECK HARNESS CONNECTOR

Check the harness connector.

Is the inspection result normal?

YES

>> GO TO 2.

NO

>> Replace harness connector.

2.

CHECK WIRING HARNESS

Check the wiring harness externals.

Is the inspection result normal?

YES

>> GO TO 3. 

NO

>> Replace wiring harness.

3.

REPLACE AIR BAG DIAGNOSIS SENSOR UNIT

1.

Replace air bag diagnosis sensor unit. Refer to 

SR-28, "Removal and Installation"

.

2.

Perform DTC confirmation procedure. Refer to 

SRC-118, "DTC Logic"

.

Is DTC detected?

YES

>> GO TO 4. 

NO

>> INSPECTION END

4.

REPLACE SIDE AIR BAG MODULE

1.

Replace side air bag module LH. Refer to 

SE-20, "SEATBACK : Disassembly and Assembly"

.

2.

Perform DTC confirmation procedure. Refer to 

SRC-118, "DTC Logic"

.

Is DTC detected?

DTC

Display contents of 

CONSULT

DTC detecting condition

Possible cause

B1135

SIDE MODULE LH 
[VB-SHORT]

Side air bag module LH circuit is shorted to 
power supply circuit

• Harness or connectors

(The module circuit is shorted.)

• Malfunction in side air bag module LH
• Malfunction in air bag diagnosis sensor unit

Revision: 2013 October

2014 JUKE

 

 

 

 

 

 

 

Content      ..     229      230      231      232     ..