Nissan Juke (2014 year). Service Repair Manual

B1086 SEAT BELT PRE-TENSIONER LH

SRC-87

< DTC/CIRCUIT DIAGNOSIS >

SRC

B1086 SEAT BELT PRE-TENSIONER LH

DTC Logic

INFOID:0000000009751780

DTC DETECTION LOGIC

DTC CONFIRMATION PROCEDURE

CHECK SELF-DIAG RESULT

With CONSULT

Turn ignition switch ON.

Perform “Self Diagnostic Result” mode of “AIR BAG” using CONSULT.

Without CONSULT

Turn ignition switch ON.

Check the air bag warning lamp status. Refer to

SRC-12, "On Board Diagnosis Function"

NOTE:
SRS does not enter the diagnosis mode if no malfunction is detected in the user mode.

Is malfunctioning part detected?

YES

>> Refer to

SRC-87, "Diagnosis Procedure"

>> INSPECTION END

Diagnosis Procedure

INFOID:0000000009751781

WARNING:

• Before servicing, turn ignition switch OFF, disconnect battery negative terminal, and wait at least 3

minutes or more. (To discharge backup capacitor.)

• Never use unspecified tester or other measuring device.

CHECK HARNESS CONNECTOR

Check the harness connector.

Is the inspection result normal?

YES

>> GO TO 2.

>> Replace harness connector.

CHECK WIRING HARNESS

Check the wiring harness externals.

Is the inspection result normal?

YES

>> GO TO 3.

>> Replace wiring harness.

REPLACE SEAT BELT PRE-TENSIONER

Replace seat belt pre-tensioner LH. Refer to

SR-30, "Removal and Installation"

Perform DTC confirmation procedure. Refer to

SRC-87, "DTC Logic"

Is DTC detected?

YES

>> GO TO 4.

>> INSPECTION END

REPLACE AIR BAG DIAGNOSIS SENSOR UNIT

Replace air bag diagnosis sensor unit. Refer to

SR-28, "Removal and Installation"

Perform DTC confirmation procedure. Refer to

SRC-87, "DTC Logic"

Is DTC detected?

DTC

Display contents of

CONSULT

DTC detecting condition

Possible cause

B1086

PRE-TEN FRONT LH
[OPEN]

Seat belt pre-tensioner LH circuit is open

• Harness or connectors

(The pre-tensioner circuit is open.)

• Malfunction in seat belt pre-tensioner LH
• Malfunction in air bag diagnosis sensor unit

Revision: 2013 October

2014 JUKE

B1087 SEAT BELT PRE-TENSIONER LH

SRC-89

< DTC/CIRCUIT DIAGNOSIS >

SRC

B1087 SEAT BELT PRE-TENSIONER LH

DTC Logic

INFOID:0000000009751782

DTC DETECTION LOGIC

DTC CONFIRMATION PROCEDURE

CHECK SELF-DIAG RESULT

With CONSULT

Turn ignition switch ON.

Perform “Self Diagnostic Result” mode of “AIR BAG” using CONSULT.

Without CONSULT

Turn ignition switch ON.

Check the air bag warning lamp status. Refer to

SRC-12, "On Board Diagnosis Function"

NOTE:
SRS does not enter the diagnosis mode if no malfunction is detected in the user mode.

Is malfunctioning part detected?

YES

>> Refer to

SRC-89, "Diagnosis Procedure"

>> INSPECTION END

Diagnosis Procedure

INFOID:0000000009751783

WARNING:

• Before servicing, turn ignition switch OFF, disconnect battery negative terminal, and wait at least 3

minutes or more. (To discharge backup capacitor.)

• Never use unspecified tester or other measuring device.

CHECK HARNESS CONNECTOR

Check the harness connector.

Is the inspection result normal?

YES

>> GO TO 2.

>> Replace harness connector.

CHECK WIRING HARNESS

Check the wiring harness externals.

Is the inspection result normal?

YES

>> GO TO 3.

>> Replace wiring harness.

REPLACE SEAT BELT PRE-TENSIONER

Replace seat belt pre-tensioner LH. Refer to

SR-30, "Removal and Installation"

Perform DTC confirmation procedure. Refer to

SRC-89, "DTC Logic"

Is DTC detected?

YES

>> GO TO 4.

>> INSPECTION END

REPLACE AIR BAG DIAGNOSIS SENSOR UNIT

Replace air bag diagnosis sensor unit. Refer to

SR-28, "Removal and Installation"

Perform DTC confirmation procedure. Refer to

SRC-89, "DTC Logic"

Is DTC detected?

DTC

Display contents of

CONSULT

DTC detecting condition

Possible cause

B1087

PRE-TEN FRONT LH
[VB-SHORT]

Seat belt pre-tensioner LH circuit is
shorted to power supply circuit

• Harness or connectors

(The pre-tensioner circuit is shorted.)

• Malfunction in seat belt pre-tensioner LH
• Malfunction in air bag diagnosis sensor unit

Revision: 2013 October

2014 JUKE

B1088 SEAT BELT PRE-TENSIONER LH

SRC-91

< DTC/CIRCUIT DIAGNOSIS >

SRC

B1088 SEAT BELT PRE-TENSIONER LH

DTC Logic

INFOID:0000000009751784

DTC DETECTION LOGIC

DTC CONFIRMATION PROCEDURE

CHECK SELF-DIAG RESULT

With CONSULT

Turn ignition switch ON.

Perform “Self Diagnostic Result” mode of “AIR BAG” using CONSULT.

Without CONSULT

Turn ignition switch ON.

Check the air bag warning lamp status. Refer to

SRC-12, "On Board Diagnosis Function"

NOTE:
SRS does not enter the diagnosis mode if no malfunction is detected in the user mode.

Is malfunctioning part detected?

YES

>> Refer to

SRC-91, "Diagnosis Procedure"

>> INSPECTION END

Diagnosis Procedure

INFOID:0000000009751785

WARNING:

• Before servicing, turn ignition switch OFF, disconnect battery negative terminal, and wait at least 3

minutes or more. (To discharge backup capacitor.)

• Never use unspecified tester or other measuring device.

CHECK HARNESS CONNECTOR

Check the harness connector.

Is the inspection result normal?

YES

>> GO TO 2.

>> Replace harness connector.

CHECK WIRING HARNESS

Check the wiring harness externals.

Is the inspection result normal?

YES

>> GO TO 3.

>> Replace wiring harness.

REPLACE SEAT BELT PRE-TENSIONER

Replace seat belt pre-tensioner LH. Refer to

SR-30, "Removal and Installation"

Perform DTC confirmation procedure. Refer to

SRC-91, "DTC Logic"

Is DTC detected?

YES

>> GO TO 4.

>> INSPECTION END

REPLACE AIR BAG DIAGNOSIS SENSOR UNIT

Replace air bag diagnosis sensor unit. Refer to

SR-28, "Removal and Installation"

Perform DTC confirmation procedure. Refer to

SRC-91, "DTC Logic"

Is DTC detected?

DTC

Display contents of

CONSULT

DTC detecting condition

Possible cause

B1088

PRE-TEN FRONT LH
[GND-SHORT]

Seat belt pre-tensioner LH circuit is
shorted to ground

• Harness or connectors

(The pre-tensioner circuit is shorted.)

• Malfunction in seat belt pre-tensioner LH
• Malfunction in air bag diagnosis sensor unit

Revision: 2013 October

2014 JUKE

B1089 SEAT BELT PRE-TENSIONER LH

SRC-93

< DTC/CIRCUIT DIAGNOSIS >

SRC

B1089 SEAT BELT PRE-TENSIONER LH

DTC Logic

INFOID:0000000009751786

DTC DETECTION LOGIC

DTC CONFIRMATION PROCEDURE

CHECK SELF-DIAG RESULT

With CONSULT

Turn ignition switch ON.

Perform “Self Diagnostic Result” mode of “AIR BAG” using CONSULT.

Without CONSULT

Turn ignition switch ON.

Check the air bag warning lamp status. Refer to

SRC-12, "On Board Diagnosis Function"

NOTE:
SRS does not enter the diagnosis mode if no malfunction is detected in the user mode.

Is malfunctioning part detected?

YES

>> Refer to

SRC-93, "Diagnosis Procedure"

>> INSPECTION END

Diagnosis Procedure

INFOID:0000000009751787

WARNING:

• Before servicing, turn ignition switch OFF, disconnect battery negative terminal, and wait at least 3

minutes or more. (To discharge backup capacitor.)

• Never use unspecified tester or other measuring device.

CHECK HARNESS CONNECTOR

Check the harness connector.

Is the inspection result normal?

YES

>> GO TO 2.

>> Replace harness connector.

CHECK WIRING HARNESS

Check the wiring harness externals.

Is the inspection result normal?

YES

>> GO TO 3.

>> Replace wiring harness.

REPLACE SEAT BELT PRE-TENSIONER

Replace seat belt pre-tensioner LH. Refer to

SR-30, "Removal and Installation"

Perform DTC confirmation procedure. Refer to

SRC-93, "DTC Logic"

Is DTC detected?

YES

>> GO TO 4.

>> INSPECTION END

REPLACE AIR BAG DIAGNOSIS SENSOR UNIT

Replace air bag diagnosis sensor unit. Refer to

SR-28, "Removal and Installation"

Perform DTC confirmation procedure. Refer to

SRC-93, "DTC Logic"

Is DTC detected?

DTC

Display contents of

CONSULT

DTC detecting condition

Possible cause

B1089

PRE-TEN FRONT LH
[SHORT]

Seat belt pre-tensioner LH circuits are
shorted to each other

• Harness or connectors

(The pre-tensioner circuit is shorted.)

• Malfunction in seat belt pre-tensioner LH
• Malfunction in air bag diagnosis sensor unit

Revision: 2013 October

2014 JUKE

B1090, B1091, B1092, B1093, B1094, B1095 DIAGNOSIS SENSOR UNIT

SRC-95

< DTC/CIRCUIT DIAGNOSIS >

SRC

B1090, B1091, B1092, B1093, B1094, B1095 DIAGNOSIS SENSOR UNIT

DTC Logic

INFOID:0000000009751788

DTC DETECTION LOGIC

DTC CONFIRMATION PROCEDURE

CHECK SELF-DIAG RESULT

With CONSULT

Turn ignition switch ON.

Perform “Self Diagnostic Result” mode of “AIR BAG” using CONSULT.

Without CONSULT

Turn ignition switch ON.

Check the air bag warning lamp status. Refer to

SRC-12, "On Board Diagnosis Function"

NOTE:
SRS does not enter the diagnosis mode if no malfunction is detected in the user mode.

Is malfunctioning part detected?

YES

>> Refer to

SRC-95, "Diagnosis Procedure"

>> INSPECTION END

Diagnosis Procedure

INFOID:0000000009751789

WARNING:

• Before servicing, turn ignition switch OFF, disconnect battery negative terminal, and wait at least 3

minutes or more. (To discharge backup capacitor.)

• Never use unspecified tester or other measuring device.

CHECK HARNESS CONNECTOR

Check the harness connector.

Is the inspection result normal?

YES

>> GO TO 2.

>> Replace harness connectors.

CHECK WIRING HARNESS

Check the wiring harness externals.
Is the inspection result normal?

YES

>> GO TO 3.

>> Replace wiring harness.

REPLACE AIR BAG DIAGNOSIS SENSOR UNIT

Replace air bag diagnosis sensor unit. Refer to

SR-28, "Removal and Installation"

Perform DTC confirmation procedure. Refer to

SRC-95, "DTC Logic"

Is DTC detected?

YES

>> GO TO 1.

>> INSPECTION END

DTC

Display contents of

CONSULT

DTC detecting condition

Possible cause

B1090
B1091
B1092
B1093
B0194
B1095

CONTROL UNIT

Air bag diagnosis sensor unit is malfunctioning

Malfunction in air bag diagnosis sensor unit

Revision: 2013 October

2014 JUKE

SRC-96

< DTC/CIRCUIT DIAGNOSIS >

B1106, B1107, B1108, B1109, B1110, B1111 DIAGNOSIS SENSOR UNIT

B1106, B1107, B1108, B1109, B1110, B1111 DIAGNOSIS SENSOR UNIT

DTC Logic

INFOID:0000000009751790

DTC DETECTION LOGIC

DTC CONFIRMATION PROCEDURE

CHECK SELF-DIAG RESULT

With CONSULT

Turn ignition switch ON.

Perform “Self Diagnostic Result” mode of “AIR BAG” using CONSULT.

Without CONSULT

Turn ignition switch ON.

Check the air bag warning lamp status. Refer to

SRC-12, "On Board Diagnosis Function"

NOTE:
SRS does not enter the diagnosis mode if no malfunction is detected in the user mode.

Is malfunctioning part detected?

YES

>> Refer to

SRC-96, "Diagnosis Procedure"

>> INSPECTION END

Diagnosis Procedure

INFOID:0000000009751791

WARNING:

• Before servicing, turn ignition switch OFF, disconnect battery negative terminal, and wait at least 3

minutes or more. (To discharge backup capacitor.)

• Never use unspecified tester or other measuring device.

CHECK HARNESS CONNECTOR

Check the harness connector.

Is the inspection result normal?

YES

>> GO TO 2.

>> Replace harness connectors.

CHECK WIRING HARNESS

Check the wiring harness externals.
Is the inspection result normal?

YES

>> GO TO 3.

>> Replace wiring harness.

REPLACE AIR BAG DIAGNOSIS SENSOR UNIT

Replace air bag diagnosis sensor unit. Refer to

SR-28, "Removal and Installation"

Perform DTC confirmation procedure. Refer to

SRC-96, "DTC Logic"

Is DTC detected?

YES

>> GO TO 1.

>> INSPECTION END

DTC

Display contents of

CONSULT

DTC detecting condition

Possible cause

B1106
B1107
B1108
B1109
B1110
B1111

CONTROL UNIT

Air bag diagnosis sensor unit is malfunctioning

Malfunction in air bag diagnosis sensor unit

Revision: 2013 October

2014 JUKE

B1113, B1114 SATELLITE SENSOR RH

SRC-97

< DTC/CIRCUIT DIAGNOSIS >

SRC

B1113, B1114 SATELLITE SENSOR RH

DTC Logic

INFOID:0000000009751792

DTC DETECTION LOGIC

DTC CONFIRMATION PROCEDURE

CHECK SELF-DIAG RESULT

With CONSULT

Turn ignition switch ON.

Perform “Self Diagnostic Result” mode of “AIR BAG” using CONSULT.

Without CONSULT

Turn ignition switch ON.

Check the air bag warning lamp status. Refer to

SRC-12, "On Board Diagnosis Function"

NOTE:
SRS does not enter the diagnosis mode if no malfunction is detected in the user mode.

Is malfunctioning part detected?

YES

>> Refer to

SRC-97, "Diagnosis Procedure"

>> INSPECTION END

Diagnosis Procedure

INFOID:0000000009751793

WARNING:

• Before servicing, turn ignition switch OFF, disconnect battery negative terminal, and wait at least 3

minutes or more. (To discharge backup capacitor.)

• Never use unspecified tester or other measuring device.

CHECK HARNESS CONNECTOR

Check the harness connector.

Is the inspection result normal?

YES

>> GO TO 2.

>> Replace harness connector.

CHECK WIRING HARNESS

Check the wiring harness externals.

Is the inspection result normal?

YES

>> GO TO 3.

>> Replace wiring harness.

REPLACE SATELLITE SENSOR

Replace satellite sensor RH. Refer to

SR-25, "Removal and Installation"

Perform DTC confirmation procedure. Refer to

SRC-97, "DTC Logic"

Is DTC detected?

YES

>> GO TO 4.

>> INSPECTION END

REPLACE AIR BAG DIAGNOSIS SENSOR UNIT

Replace air bag diagnosis sensor unit. Refer to

SR-28, "Removal and Installation"

Perform DTC confirmation procedure. Refer to

SRC-97, "DTC Logic"

Is DTC detected?

YES

>> GO TO 1.

DTC

Display contents of

CONSULT

DTC detecting condition

Possible cause

B1113
B1114

SATELLITE SENS RH
[UNIT FAIL]

Satellite sensor RH is malfunctioning

• Harness or connectors
• Malfunction in satellite sensor RH
• Malfunction in air bag diagnosis sensor unit

Revision: 2013 October

2014 JUKE

B1115 SATELLITE SENSOR RH

SRC-99

< DTC/CIRCUIT DIAGNOSIS >

SRC

B1115 SATELLITE SENSOR RH

DTC Logic

INFOID:0000000009751794

DTC DETECTION LOGIC

DTC CONFIRMATION PROCEDURE

CHECK SELF-DIAG RESULT

With CONSULT

Turn ignition switch ON.

Perform “Self Diagnostic Result” mode of “AIR BAG” using CONSULT.

Without CONSULT

Turn ignition switch ON.

Check the air bag warning lamp status. Refer to

SRC-12, "On Board Diagnosis Function"

NOTE:
SRS does not enter the diagnosis mode if no malfunction is detected in the user mode.

Is malfunctioning part detected?

YES

>> Refer to

SRC-99, "Diagnosis Procedure"

>> INSPECTION END

Diagnosis Procedure

INFOID:0000000009751795

WARNING:

• Before servicing, turn ignition switch OFF, disconnect battery negative terminal, and wait at least 3

minutes or more. (To discharge backup capacitor.)

• Never use unspecified tester or other measuring device.

CHECK HARNESS CONNECTOR

Check the harness connector.

Is the inspection result normal?

YES

>> GO TO 2.

>> Replace harness connector.

CHECK WIRING HARNESS

Check the wiring harness externals.

Is the inspection result normal?

YES

>> GO TO 3.

>> Replace wiring harness.

REPLACE SATELLITE SENSOR

Replace satellite sensor RH. Refer to

SR-25, "Removal and Installation"

Perform DTC confirmation procedure. Refer to

SRC-99, "DTC Logic"

Is DTC detected?

YES

>> GO TO 4.

>> INSPECTION END

REPLACE AIR BAG DIAGNOSIS SENSOR UNIT

Replace air bag diagnosis sensor unit. Refer to

SR-28, "Removal and Installation"

Perform DTC confirmation procedure. Refer to

SRC-99, "DTC Logic"

Is DTC detected?

YES

>> GO TO 1.

DTC

Display contents of

CONSULT

DTC detecting condition

Possible cause

B1115

SATELLITE SENS RH
[COMM FAIL]

Satellite sensor RH is malfunctioning or out
of the specified specification

• Harness or connectors
• Malfunction in satellite sensor RH
• Malfunction in air bag diagnosis sensor unit

Revision: 2013 October

2014 JUKE

B1116 SATELLITE SENSOR RH

SRC-101

< DTC/CIRCUIT DIAGNOSIS >

SRC

B1116 SATELLITE SENSOR RH

DTC Logic

INFOID:0000000009751796

DTC DETECTION LOGIC

DTC CONFIRMATION PROCEDURE

CHECK SELF-DIAG RESULT

With CONSULT

Turn ignition switch ON.

Perform “Self Diagnostic Result” mode of “AIR BAG” using CONSULT.

Without CONSULT

Turn ignition switch ON.

Check the air bag warning lamp status. Refer to

SRC-12, "On Board Diagnosis Function"

NOTE:
SRS does not enter the diagnosis mode if no malfunction is detected in the user mode.
Is malfunctioning part detected?

YES

>> Refer to

SRC-101, "Diagnosis Procedure"

>> INSPECTION END

Diagnosis Procedure

INFOID:0000000009751797

WARNING:

• Before servicing, turn ignition switch OFF, disconnect battery negative terminal, and wait at least 3

minutes or more. (To discharge backup capacitor.)

• Never use unspecified tester or other measuring device.

CHECK HARNESS CONNECTOR

Check the harness connector.
Is the inspection result normal?

YES

>> GO TO 2.

>> Replace harness connector.

CHECK WIRING HARNESS

Check the wiring harness externals.
Is the inspection result normal?

YES

>> GO TO 3.

>> Replace wiring harness.

REPLACE SATELLITE SENSOR

Replace satellite sensor RH. Refer to

SR-25, "Removal and Installation"

Perform DTC confirmation procedure. Refer to

SRC-101, "DTC Logic"

Is DTC detected?

YES

>> GO TO 4.

>> INSPECTION END

REPLACE AIR BAG DIAGNOSIS SENSOR UNIT

Replace air bag diagnosis sensor unit. Refer to

SR-28, "Removal and Installation"

Perform DTC confirmation procedure. Refer to

SRC-101, "DTC Logic"

Is DTC detected?

YES

>> GO TO 1.

>> INSPECTION END

DTC

Display contents of

CONSULT

DTC detecting condition

Possible cause

B1116

SATELLITE SENS RH
[UNMATCH]

Satellite sensor RH is out of the specified
specification

Diagnosis sensor unit or satellite sensor RH is dif-
ferent from the part specified

Revision: 2013 October

2014 JUKE

SRC-102

< DTC/CIRCUIT DIAGNOSIS >

B1118, B1119 SATELLITE SENSOR LH

B1118, B1119 SATELLITE SENSOR LH

DTC Logic

INFOID:0000000009751798

DTC DETECTION LOGIC

DTC CONFIRMATION PROCEDURE

CHECK SELF-DIAG RESULT

With CONSULT

Turn ignition switch ON.

Perform “Self Diagnostic Result” mode of “AIR BAG” using CONSULT.

Without CONSULT

Turn ignition switch ON.

Check the air bag warning lamp status. Refer to

SRC-12, "On Board Diagnosis Function"

NOTE:
SRS does not enter the diagnosis mode if no malfunction is detected in the user mode.

Is malfunctioning part detected?

YES

>> Refer to

SRC-102, "Diagnosis Procedure"

>> INSPECTION END

Diagnosis Procedure

INFOID:0000000009751799

WARNING:

• Before servicing, turn ignition switch OFF, disconnect battery negative terminal, and wait at least 3

minutes or more. (To discharge backup capacitor.)

• Never use unspecified tester or other measuring device.

CHECK HARNESS CONNECTOR

Check the harness connector.

Is the inspection result normal?

YES

>> GO TO 2.

>> Replace harness connector.

CHECK WIRING HARNESS

Check the wiring harness externals.

Is the inspection result normal?

YES

>> GO TO 3.

>> Replace wiring harness.

REPLACE SATELLITE SENSOR

Replace satellite sensor LH. Refer to

SR-25, "Removal and Installation"

Perform DTC confirmation procedure. Refer to

SRC-102, "DTC Logic"

Is DTC detected?

YES

>> GO TO 4.

>> INSPECTION END

REPLACE AIR BAG DIAGNOSIS SENSOR UNIT

Replace air bag diagnosis sensor unit. Refer to

SR-28, "Removal and Installation"

Perform DTC confirmation procedure. Refer to

SRC-102, "DTC Logic"

Is DTC detected?

YES

>> GO TO 1.

DTC

Display contents of

CONSULT

DTC detecting condition

Possible cause

B1118
B1119

SATELLITE SENS LH
[UNIT FAIL]

Satellite sensor LH is malfunctioning

• Harness or connectors
• Malfunction in satellite sensor LH
• Malfunction in air bag diagnosis sensor unit

Revision: 2013 October

2014 JUKE

Nissan Juke (2014 year). Service Repair Manual - part 230