Nissan Juke (2014 year). Service Repair Manual - part 221

 

  Index      Manuals     Nissan Juke (2014 year) - Service and Repair Manual

 

Search            copyright infringement  

 

 

 

 

 

 

 

 

Content      ..     219      220      221      222     ..

 

 

Nissan Juke (2014 year). Service Repair Manual - part 221

 

 

B2193 CHAIN OF ECM-IMMU

SEC-171

< DTC/CIRCUIT DIAGNOSIS >

[WITHOUT INTELLIGENT KEY SYSTEM]

C

D

E

F

G

H

I

J

L

M

A

B

SEC

N

O

P

B2193 CHAIN OF ECM-IMMU

DTC Logic

INFOID:0000000009754777

DTC DETECTION LOGIC

NOTE:
• If DTC B2193 is displayed with DTC U1000, first perform the trouble diagnosis for DTC U1000. Refer to

BCS-147, "DTC Logic"

.

• If DTC B2193 is displayed with DTC U1010, first perform the trouble diagnosis for DTC U1010. Refer to

BCS-148, "DTC Logic"

.

DTC CONFIRMATION PROCEDURE

1.

PERFORM DTC CONFIRMATION PROCEDURE

1.

Turn ignition switch ON.

2.

Check DTC in “Self Diagnostic Result” mode of “BCM” using CONSULT.

Is DTC detected?

YES

>> Refer to 

SEC-171, "Diagnosis Procedure"

.

NO

>> INSPECTION END

Diagnosis Procedure

INFOID:0000000009754778

1.

REPLACE BCM

1.

Replace BCM. Refer to 

BCS-157, "Removal and Installation"

.

2.

Perform initialization of BCM and registration of all ignition keys using CONSULT.

Can the system be initialized and can the engine be started with registered ignition key?

YES

>> INSPECTION END

NO

>> GO TO 2.

2.

REPLACE ECM

Replace ECM.
Refer to 

EC-561, "Removal and Installation"

.

>> INSPECTION END

DTC No.

Trouble diagnosis name

DTC detecting condition

Possible cause

B2193

CHAIN OF BCM-ECM

Inactive communication between ECM 
and BCM

• Harness or connectors

(The CAN communication line is open 
or shorted.)

• BCM
• ECM

Revision: 2013 October

2014 JUKE

SEC-172

< DTC/CIRCUIT DIAGNOSIS >

[WITHOUT INTELLIGENT KEY SYSTEM]

B2195 ANTI-SCANNING

B2195 ANTI-SCANNING

DTC Logic

INFOID:0000000009754779

DTC DETECTION LOGIC

DTC CONFIRMATION PROCEDURE

1.

PERFORM DTC CONFIRMATION PROCEDURE

1.

Turn ignition switch ON.

2.

Check DTC in “Self Diagnostic Result” mode of “BCM” using CONSULT.

Is DTC detected?

YES

>> Refer to 

SEC-172, "Diagnosis Procedure"

.

NO

>> INSPECTION END.

Diagnosis Procedure

INFOID:0000000009754780

1.

CHECK SELF DIAGNOSTIC RESULT 1

1.

Select “Self Diagnostic Result” of “BCM” using CONSULT.

2.

Erase DTC.

3.

Perform DTC Confirmation Procedure for DTC P2195. Refer to 

SEC-172, "DTC Logic"

.

Is DTC detected?

YES

>> GO TO 2. 

NO

>> INSPECTION END

2.

CHECK EQUIPMENT OF THE VEHICLE

Check that unspecified accessory part related to engine start is not installed.

Is unspecified accessory part related to engine start installed?

YES

>> GO TO 3.

NO

>> GO TO 4.

3.

CHECK SELF DIAGNOSTIC RESULT 2

1.

Obtain the customers approval to remove unspecified accessory part related to engine start, and then
remove it.

2.

Select “Self Diagnostic Result” of “BCM” using CONSULT.

3.

Erase DTC.

4.

Perform DTC CONFIRMATION PROCEDURE for DTC B2195. Refer to 

SEC-172, "DTC Logic"

.

Is DTC detected?

YES

>> GO TO 4.

NO

>> INSPECTION END

4.

REPLACE BCM

1.

Replace BCM. Refer to 

BCS-157, "Removal and Installation"

.

2.

Perform initialization of BCM and registration of all ignition keys using CONSULT.

>> INSPECTION END

DTC No.

Trouble diagnosis name

DTC detecting condition

Possible cause

B2195

ANTI SCANNING

ID verification between BCM and ECM that is 
out of the specified specification is detected

ID verification request out of the 
specified specification

Revision: 2013 October

2014 JUKE

B2196 DONGLE UNIT

SEC-173

< DTC/CIRCUIT DIAGNOSIS >

[WITHOUT INTELLIGENT KEY SYSTEM]

C

D

E

F

G

H

I

J

L

M

A

B

SEC

N

O

P

B2196 DONGLE UNIT

Description

INFOID:0000000009754781

BCM performs ID verification between BCM and dongle unit.
When verification result is OK, BCM permits cranking.

DTC Logic

INFOID:0000000009754782

DTC DETECTION LOGIC

DTC CONFIRMATION PROCEDURE

1.

PERFORM DTC CONFIRMATION PROCEDURE

1.

Turn ignition switch ON.

2.

Turn ignition switch OFF.

3.

Turn ignition switch ON.

4.

Check DTC in “Self-diagnosis result” mode of “BCM” using CONSULT.

Is the DTC detected?

YES

>> Refer to 

SEC-173, "Diagnosis Procedure"

.

NO

>> INSPECTION END

Diagnosis Procedure

INFOID:0000000009754783

1.

PERFORM INITIALIZATION

1.

Perform initialization of BCM and registration of all Intelligent Keys using CONSULT.

2.

Start the engine.

Dose the engine start?

YES

>> INSPECTION END

NO

>> GO TO 2.

2.

CHECK DONGLE UNIT CIRCUIT

1.

Turn ignition switch OFF.

2.

Disconnect BCM connector and dongle unit connector.

3.

Check continuity between BCM harness connector and dongle unit harness connector.

4.

Check continuity between BCM harness connector and ground.

Is the inspection result normal?

YES

>> GO TO 3.

NO

>> Repair or replace harness.

3.

CHECK DONGLE UNIT GROUND CIRCUIT

Check continuity between dongle unit harness connector and ground.

DTC No.

Trouble diagnosis name

DTC detecting condition

Possible cause

B2196

DONGLE NG

The ID verification results between BCM 
and dongle unit is NG.

• Harness or connectors

(Dongle unit circuit is open or shorted.)

• Dongle unit

BCM

Dongle unit

Continuity

Connector

Terminal

Connector

Terminal

M68

24

M86

7

Existed

BCM

Ground

Continuity

Connector

Terminal

M68

24

Not existed

Revision: 2013 October

2014 JUKE

SEC-174

< DTC/CIRCUIT DIAGNOSIS >

[WITHOUT INTELLIGENT KEY SYSTEM]

B2196 DONGLE UNIT

Is the inspection result normal?

YES

>> Replace dongle unit.

NO

>> Repair or replace harness.

Dongle unit

Ground

Continuity

Connector

Terminal

M86

1

Existed

Revision: 2013 October

2014 JUKE

B209F CRANKING REQUEST CIRCUIT

SEC-175

< DTC/CIRCUIT DIAGNOSIS >

[WITHOUT INTELLIGENT KEY SYSTEM]

C

D

E

F

G

H

I

J

L

M

A

B

SEC

N

O

P

B209F CRANKING REQUEST CIRCUIT

DTC Logic

INFOID:0000000009754784

DTC DETECTION LOGIC

NOTE:
If DTC B209F is displayed with DTC U1000, first perform the trouble diagnosis for DTC U1000. Refer to 

PCS-

58, "DTC Logic"

.

DTC CONFIRMATION PROCEDURE

1.

PERFORM DTC CONFIRMATION PROCEDURE

1.

Perform DTC CONFIRMATION PROCEDURE for DTC P1650. Refer to 

EC-470, "DTC Logic"

.

2.

Turn ignition switch ON.

3.

Check DTC in “Self Diagnostic Result” mode of “IPDM E/R” using CONSULT.

Is DTC detected?

YES

>> Refer to 

SEC-175, "Diagnosis Procedure"

.

NO

>> INSPECTION END

Diagnosis Procedure

INFOID:0000000009754785

1.

CHECK CRANKING REQUEST SIGNAL

1.

Turn ignition switch ON.

2.

Check voltage between IPDM E/R harness connector and ground under the following conditions.

Is the inspection result normal?

YES

>> GO TO 3.

NO

>> GO TO 2.

2.

CHECK CRANKING REQUEST SIGNAL CIRCUIT

1.

Turn ignition switch OFF.

2.

Disconnect IPDM E/R connector.

3.

Disconnect ECM connector.

4.

Check continuity between IPDM E/R harness connector and ECM harness connector.

DTC No.

Trouble diagnosis name

DTC detecting condition

Possible cause

B209F

CRANK REQ CIR OPEN 

When the following items do not match, a 
malfunction is detected.
• Cranking request signal from ECM
• Starter control relay control signal from 

ECM (CAN)

• Harness or connectors

(CAN communication line is open or 
shorted.)

• Harness or connectors

(Cranking request signal circuit is open 
or shorted.)

• IPDM  E/R
• ECM

(+)

(–)

Condition

Voltage (V)

(Approx.)

IPDM E/R

Connector

Terminal

E13

23

Ground

Ignition switch OFF

3.6

Ignition switch ON

• Engine: Stopped
• Selector lever position: P

0 – 1

• Engine: Stopped
• Selector lever position: 

Other than P

12 – 16

Engine running

12 – 16

Revision: 2013 October

2014 JUKE

SEC-176

< DTC/CIRCUIT DIAGNOSIS >

[WITHOUT INTELLIGENT KEY SYSTEM]

B209F CRANKING REQUEST CIRCUIT

5.

Check continuity between BCM harness connector and ground.

Is the inspection result normal?

YES

>> GO TO 3.

NO

>> Repair or replace harness.

3.

REPLACE IPDM E/R

1.

Replace IPDM E/R. Refer to 

PCS-62, "Removal and Installation"

.

2.

Perform DTC CONFIRMATION PROCEDURE for DTC B209F. Refer to 

SEC-175, "DTC Logic"

.

Is DTC detected?

YES

>> GO TO 4.

NO

>> INSPECTION END

4.

REPLACE ECM

Replace ECM.
Refer to 

EC-561, "Removal and Installation"

.

>> INSPECTION END

IPDM E/R

ECM

Continuity

Connector

Terminal

Connector

Terminal

E13

23

F26

92

Existed

IPDM E/R

Ground

Continuity

Connector

Terminal

E13

23

Not existed

Revision: 2013 October

2014 JUKE

B20A0 CRANKING REQUEST CIRCUIT

SEC-177

< DTC/CIRCUIT DIAGNOSIS >

[WITHOUT INTELLIGENT KEY SYSTEM]

C

D

E

F

G

H

I

J

L

M

A

B

SEC

N

O

P

B20A0 CRANKING REQUEST CIRCUIT

DTC Logic

INFOID:0000000009754786

DTC DETECTION LOGIC

NOTE:
If DTC B20A0 is displayed with DTC U1000, first perform the trouble diagnosis for DTC U1000. Refer to 

PCS-

58, "DTC Logic"

.

DTC CONFIRMATION PROCEDURE

1.

PERFORM DTC CONFIRMATION PROCEDURE

1.

Perform DTC CONFIRMATION PROCEDURE for DTC P1650. Refer to 

EC-470, "DTC Logic"

.

2.

Turn ignition switch ON.

3.

Check DTC in “Self Diagnostic Result” mode of “IPDM E/R” using CONSULT.

Is DTC detected?

YES

>> Refer to 

SEC-177, "Diagnosis Procedure"

.

NO

>> INSPECTION END

Diagnosis Procedure

INFOID:0000000009754787

1.

CHECK CRANKING REQUEST SIGNAL

1.

Turn ignition switch ON.

2.

Check voltage between IPDM E/R harness connector and ground under the following conditions.

Is the inspection result normal?

YES

>> GO TO 3.

NO

>> GO TO 2.

2.

CHECK CRANKING REQUEST SIGNAL CIRCUIT

1.

Turn ignition switch OFF.

2.

Disconnect IPDM E/R connector.

3.

Disconnect ECM connector.

4.

Check continuity between IPDM E/R harness connector and ECM harness connector.

DTC No.

Trouble diagnosis name

DTC detecting condition

Possible cause

B20A0

CRANK REQ CIR SHORT 

When the following items do not match, a 
malfunction is detected.
• Cranking request signal from ECM
• Starter control relay control signal from 

ECM (CAN)

• Harness or connectors

(CAN communication line is open or 
shorted.)

• Harness or connectors

(Cranking request signal circuit is open or 
shorted.)

• IPDM E/R
• ECM

(+)

(–)

Condition

Voltage (V)

(Approx.)

IPDM E/R

Connector

Terminal

E13

23

Ground

Ignition switch OFF

3.6

Ignition switch ON

• Engine: Stopped
• Selector lever position: P

0 – 1

• Engine: Stopped
• Selector lever position: 

Other than P

12 – 16

Engine running

12 – 16

Revision: 2013 October

2014 JUKE

SEC-178

< DTC/CIRCUIT DIAGNOSIS >

[WITHOUT INTELLIGENT KEY SYSTEM]

B20A0 CRANKING REQUEST CIRCUIT

5.

Check continuity between BCM harness connector and ground.

Is the inspection result normal?

YES

>> GO TO 3.

NO

>> Repair or replace harness.

3.

REPLACE IPDM E/R

1.

Replace IPDM E/R. Refer to 

PCS-62, "Removal and Installation"

.

2.

Perform DTC CONFIRMATION PROCEDURE for DTC B20A0. Refer to 

SEC-177, "DTC Logic"

.

Is DTC detected?

YES

>> GO TO 4.

NO

>> INSPECTION END

4.

REPLACE ECM

Replace ECM.
Refer to 

EC-561, "Removal and Installation"

.

>> INSPECTION END

IPDM E/R

ECM

Continuity

Connector

Terminal

Connector

Terminal

E13

23

F26

92

Existed

IPDM E/R

Ground

Continuity

Connector

Terminal

E13

23

Not existed

Revision: 2013 October

2014 JUKE

B210B STARTER CONTROL RELAY

SEC-179

< DTC/CIRCUIT DIAGNOSIS >

[WITHOUT INTELLIGENT KEY SYSTEM]

C

D

E

F

G

H

I

J

L

M

A

B

SEC

N

O

P

B210B STARTER CONTROL RELAY

DTC Logic

INFOID:0000000009754788

DTC DETECTION LOGIC

NOTE:
If DTC B210B is displayed with DTC U1000, first perform the trouble diagnosis for DTC U1000. Refer to 

PCS-

58, "DTC Logic"

.

DTC CONFIRMATION PROCEDURE

1.

PERFORM DTC CONFIRMATION PROCEDURE 1

1.

Press push-button ignition switch under the following conditions to start engine, and wait 5 seconds or
more.

CVT models

-

Selector lever: In the P position

-

Brake pedal: Depressed

M/T models

-

Shift lever: In the Neutral position

-

Clutch pedal: Depressed

2.

Check DTC in “Self Diagnostic Result” mode of “IPDM E/R” using CONSULT.

Is DTC detected?

YES

>> Go to 

SEC-179, "Diagnosis Procedure"

.

NO-1 (M/T models)>>INSPECTION END
NO-2 (CVT models)>>GO TO 2.

2.

PERFORM DTC CONFIRMATION PROCEDURE 2

1.

Stop engine.

2.

Perform DTC CONFIRMATION PROCEDURE for DTC P1650. Refer to 

EC-470, "DTC Logic"

.

3.

Turn ignition switch ON.

4.

Check DTC in “Self Diagnostic Result” mode of “IPDM E/R” using CONSULT.

Is DTC detected?

YES

>> Refer to 

SEC-179, "Diagnosis Procedure"

.

NO

>> INSPECTION END

Diagnosis Procedure

INFOID:0000000009754789

1.

INSPECTION START

Perform inspection in accordance with procedure that confirms DTC.

Which procedure confirms DTC?

DTC confirmation procedure 1>>GO TO 2.

DTC No.

Trouble diagnosis name

DTC detecting condition

Possible cause

B210B

START CONT RLY ON

When comparing the following items, 
IPDM E/R detects that starter control relay 
is stuck in the ON position for 5 seconds or 
more.
• Starter control relay control signal (CAN) 

from BCM

• Starter control relay control signal (CAN) 

from ECM

• Starter control relay and starter relay sta-

tus signal (IPDM E/R input)

• Starter control relay control signal (IPDM 

E/R output)

• Ignition switch START signal
• Ignition power supply signal
• Cranking request signal from ECM

• Harness or connectors

(CAN communication line is open or 
shorted.
(Ignition switch START signal circuit is 
open or shorted.)

• IPDM  E/R
• BCM

Revision: 2013 October

2014 JUKE

SEC-180

< DTC/CIRCUIT DIAGNOSIS >

[WITHOUT INTELLIGENT KEY SYSTEM]

B210B STARTER CONTROL RELAY

DTC confirmation procedure 2>>GO TO 5.

2.

CHECK DTC OF BCM

Check DTC in “Self Diagnostic Result” mode of “BCM” using CONSULT.

Is DTC detected?

YES

>> Perform the trouble diagnosis related to the detected DTC. Refer to 

BCS-132, "DTC Index"

.

NO

>> GO TO 3.

3.

CHECK IGNITION SWITCH START SIGNAL

1.

Turn ignition switch OFF.

2.

Disconnect IPDM E/R harness connector.

3.

Check voltage between IPDM E/R harness connector and ground.

Is the inspection result normal?

YES

>> GO TO 4.

NO

>> Repair or replace harness. Refer to 

STR-19, "Wiring Diagram (CVT Models)"

.

4.

PERFORM DTC CONFIRMATION PROCEDURE AGAIN

1.

Reconnect IPDM E/R harness connector.

2.

Turn ignition switch ON.

3.

Select “Self Diagnostic Result” mode of “IPDM E/R” using CONSULT.

4.

Touch “ERASE”.

5.

Perform DTC CONFIRMATION PROCEDURE for DTC B210B. Refer to 

SEC-179, "DTC Logic"

.

Is DTC detected?

YES

>> Replace IPDM E/R. Refer to 

PCS-62, "Removal and Installation"

.

NO

>> INSPECTION END

5.

PERFORM DTC CONFIRMATION PROCEDURE AGAIN

1.

Turn ignition switch ON.

2.

Select “Self Diagnostic Result” mode of “IPDM E/R” using CONSULT.

3.

Touch “ERASE”.

4.

Perform DTC CONFIRMATION PROCEDURE for DTC B210B. Refer to 

SEC-179, "DTC Logic"

.

Is DTC detected?

YES

>> Replace IPDM E/R. Refer to 

PCS-62, "Removal and Installation"

.

NO

>> INSPECTION END

(+)

(–)

Condition

Voltage (V)

IPDM E/R

Connector

Terminal

E10

6

Ground

Ignition switch

START position

6 – 16

Except START position

0 – 1

Revision: 2013 October

2014 JUKE

B210C STARTER CONTROL RELAY

SEC-181

< DTC/CIRCUIT DIAGNOSIS >

[WITHOUT INTELLIGENT KEY SYSTEM]

C

D

E

F

G

H

I

J

L

M

A

B

SEC

N

O

P

B210C STARTER CONTROL RELAY

DTC Logic

INFOID:0000000009754790

DTC DETECTION LOGIC

NOTE:
• If DTC B210C is displayed with DTC U1000, first perform the trouble diagnosis for DTC U1000. Refer to

PCS-58, "DTC Logic"

.

• When IPDM E/R power supply voltage is low (Approx. 7 - 8 V for about 1 second), the DTC B210C may be

detected.

DTC CONFIRMATION PROCEDURE

1.

PERFORM DTC CONFIRMATION PROCEDURE 1

1.

Press push-button ignition switch under the following conditions to start engine, and wait 5 seconds or
more.

CVT models

-

Selector lever: In the P position

-

Brake pedal: Depressed

M/T models

-

Shift lever: In the Neutral position

-

Clutch pedal: Depressed

2.

Check DTC in “Self Diagnostic Result” mode of “IPDM E/R” using CONSULT.

Is DTC detected?

YES

>> Go to 

SEC-181, "Diagnosis Procedure"

.

NO-1 (M/T models)>>INSPECTION END
NO-2 (CVT models)>>GO TO 2.

2.

PERFORM DTC CONFIRMATION PROCEDURE 2

1.

Stop engine.

2.

Perform DTC CONFIRMATION PROCEDURE for DTC P1650. Refer to 

EC-470, "DTC Logic"

.

3.

Turn ignition switch ON.

4.

Check DTC in “Self Diagnostic Result” mode of “IPDM E/R” using CONSULT.

Is DTC detected?

YES

>> Refer to 

SEC-181, "Diagnosis Procedure"

.

NO

>> INSPECTION END

Diagnosis Procedure

INFOID:0000000009754791

1.

INSPECTION START

Perform inspection in accordance with procedure that confirms DTC.
Which procedure confirms DTC?

DTC No.

Trouble diagnosis name

DTC detecting condition

Possible cause

B210C

START CONT RLY OFF

When comparing the following items, IPDM 
E/R detects that starter control relay is stuck 
in the OFF position for 5 seconds or more.
• Starter control relay control signal (CAN) 

from BCM

• Starter control relay control signal (CAN) 

from ECM

• Starter control relay and starter relay status 

signal (IPDM E/R input)

• Starter control relay control signal (IPDM E/

R output)

• Ignition switch START signal
• Ignition power supply signal
• Cranking request signal from ECM

• Harness or connectors

(CAN communication line is open or 
shorted.
(Transmission range switch circuit is 
open or shorted.)
(Clutch interlock switch circuit is 
open or shorted.)
(Ignition switch START signal circuit 
is open or shorted.)
(Ignition power supply circuit is open 
or shorted.)

• IPDM E/R
• BCM

Revision: 2013 October

2014 JUKE

SEC-182

< DTC/CIRCUIT DIAGNOSIS >

[WITHOUT INTELLIGENT KEY SYSTEM]

B210C STARTER CONTROL RELAY

DTC confirmation procedure 1>>GO TO 2.
DTC confirmation procedure 2>>GO TO 7.

2.

CHECK DTC OF BCM

Check DTC in “Self Diagnostic Result” mode of “BCM” using CONSULT.

Is DTC detected?

YES

>> Perform the trouble diagnosis related to the detected DTC. Refer to 

BCS-132, "DTC Index"

.

NO-1 (M/T models)>>GO TO 4.
NO-2 (CVT models)>>GO TO 3.

3.

CHECK DTC OF TCM

Check DTC in “Self Diagnostic Result” mode of “TRANSMISSION” using CONSULT.

Is DTC detected?

YES

>> Perform the trouble diagnosis related to the detected DTC. Refer to 

TM-198, "DTC Index"

.

NO

>> GO TO 4.

4.

CHECK TRANSMISSION RANGE SWITCH SIGNAL

1.

Turn ignition switch ON.

2.

Check voltage between IPDM E/R harness connector and ground.

Is the inspection result normal?

YES

>> GO TO 5.

NO

>> Repair or replace harness.

5.

CHECK IGNITION SWITCH START SIGNAL

1.

Turn ignition switch OFF.

2.

Disconnect IPDM E/R harness connector.

3.

Check voltage between IPDM E/R harness connector and ground.

Is the inspection result normal?

YES

>> GO TO 6.

NO

>> Repair or replace harness. Refer to 

STR-19, "Wiring Diagram (CVT Models)"

.

6.

PERFORM DTC CONFIRMATION PROCEDURE AGAIN

1.

Reconnect IPDM E/R harness connector.

2.

Turn ignition switch ON.

3.

Select “Self Diagnostic Result” mode of “IPDM E/R” using CONSULT.

4.

Touch “ERASE”.

5.

Perform DTC CONFIRMATION PROCEDURE for DTC B210C. Refer to 

SEC-181, "DTC Logic"

.

Is DTC detected?

YES

>> Replace IPDM E/R. Refer to 

PCS-62, "Removal and Installation"

.

NO

>> INSPECTION END

(+)

(–)

Condition

Voltage (V)

IPDM E/R

Connector

Terminal

E15

48

Ground

M/T models

Clutch pedal

Depressed

9 – 16

Not depressed

0 – 1

CVT models

Selector lever

P or N position

9 – 16

Except above position

0 – 1

(+)

(–)

Condition

Voltage (V)

(Approx.)

IPDM E/R

Connector

Terminal

E10

6

Ground

Ignition switch

START position

6 – 16

Except START position

0 – 1

Revision: 2013 October

2014 JUKE

B210C STARTER CONTROL RELAY

SEC-183

< DTC/CIRCUIT DIAGNOSIS >

[WITHOUT INTELLIGENT KEY SYSTEM]

C

D

E

F

G

H

I

J

L

M

A

B

SEC

N

O

P

7.

CHECK IGNITION POWER SUPPLY SIGNAL

1.

Turn ignition switch OFF.

2.

Disconnect IPDM E/R harness connector.

3.

Check voltage between IPDM E/R harness connector and ground.

Is the inspection result normal?

YES

>> Replace IPDM E/R. Refer to 

PCS-62, "Removal and Installation"

.

NO

>> Repair or replace harness. Refer to 

STR-19, "Wiring Diagram (CVT Models)"

.

(+)

(–)

Condition

Voltage (V)

(Approx.)

IPDM E/R

Connector

Terminal

E17

69

Ground

Ignition switch

ON position

6 – 16

ACC or OFF position

0 – 1

Revision: 2013 October

2014 JUKE

SEC-184

< DTC/CIRCUIT DIAGNOSIS >

[WITHOUT INTELLIGENT KEY SYSTEM]

B210D STARTER RELAY

B210D STARTER RELAY

DTC Logic

INFOID:0000000009754792

DTC DETECTION LOGIC

NOTE:
• If DTC B210D is displayed with DTC U1000, first perform the trouble diagnosis for DTC U1000. Refer to

PCS-58, "DTC Logic"

.

• If DTC B210D is displayed with DTC B209F, first perform the trouble diagnosis for DTC B209F. Refer to

SEC-175, "DTC Logic"

.

• If DTC B210D is displayed with DTC B20A0, first perform the trouble diagnosis for DTC B20A0. Refer to

SEC-177, "DTC Logic"

.

DTC CONFIRMATION PROCEDURE

1.

PERFORM DTC CONFIRMATION PROCEDURE 1

1.

Press push-button ignition switch under the following conditions to start engine, and wait 5 seconds or
more.

-

Selector lever: In the P position

-

Brake pedal: Depressed

2.

Check DTC in “Self Diagnostic Result” mode of “IPDM E/R” using CONSULT.

Is DTC detected?

YES

>> Go to 

SEC-184, "Diagnosis Procedure"

.

NO

>> GO TO 2.

2.

PERFORM DTC CONFIRMATION PROCEDURE 2

1.

Stop engine.

2.

Perform DTC CONFIRMATION PROCEDURE for DTC P1650. Refer to 

EC-470, "DTC Logic"

.

3.

Turn ignition switch ON.

4.

Check DTC in “Self Diagnostic Result” mode of “IPDM E/R” using CONSULT.

Is DTC detected?

YES

>> Refer to 

SEC-184, "Diagnosis Procedure"

.

NO

>> INSPECTION END

Diagnosis Procedure

INFOID:0000000009754793

1.

CHECK STARTER RELAY CONTROL SIGNAL

1.

Turn ignition switch ON.

2.

Check voltage between IPDM E/R harness connector and ground.

DTC No.

Trouble diagnosis name

DTC detecting condition

Possible cause

B210D

STARTER RELAY ON

When comparing the following items, IPDM E/R 
detects that starter relay is stuck in the ON po-
sition for 5 seconds or more.
• Starter control relay control signal (CAN) 

from BCM

• Starter control relay control signal (CAN) 

from ECM

• Starter control relay and starter relay status 

signal (IPDM E/R input)

• Starter control relay control signal (IPDM E/R 

output)

• Ignition switch START signal
• Ignition power supply signal
• Cranking request signal from ECM

• Harness or connectors

(CAN communication line is 
open or shorted.
(Starter relay circuit is open or 
shorted.

• IPDM  E/R

Revision: 2013 October

2014 JUKE

B210D STARTER RELAY

SEC-185

< DTC/CIRCUIT DIAGNOSIS >

[WITHOUT INTELLIGENT KEY SYSTEM]

C

D

E

F

G

H

I

J

L

M

A

B

SEC

N

O

P

Is the inspection result normal?

YES

>> GO TO 5.

NO

>> GO TO 2.

2.

CHECK CRANKING REQUEST SIGNAL CIRCUIT

1.

Turn ignition switch OFF.

2.

Disconnect IPDM E/R connector.

3.

Disconnect ECM connector.

4.

Check continuity between IPDM E/R harness connector and ECM harness connector.

5.

Check continuity between BCM harness connector and ground.

Is the inspection result normal?

YES

>> GO TO 3.

NO

>> Repair or replace harness.

3.

REPLACE IPDM E/R

1.

Replace IPDM E/R. Refer to 

PCS-62, "Removal and Installation"

.

2.

Perform DTC CONFIRMATION PROCEDURE for DTC B210D. Refer to 

SEC-184, "DTC Logic"

.

Is DTC detected?

YES

>> GO TO 4.

NO

>> INSPECTION END

4.

REPLACE ECM

Replace ECM.
Refer to 

EC-561, "Removal and Installation"

.

>> INSPECTION END

5.

PERFORM DTC CONFIRMATION PROCEDURE AGAIN

1.

Turn ignition switch ON.

2.

Select “Self Diagnostic Result” mode of “IPDM E/R” using CONSULT.

3.

Touch “ERASE”.

4.

Perform DTC CONFIRMATION PROCEDURE for DTC B210D. Refer to 

SEC-184, "DTC Logic"

.

Is DTC detected?

YES

>> Replace IPDM E/R. Refer to 

PCS-62, "Removal and Installation"

.

NO

>> INSPECTION END

(+)

(–)

Voltage (V)

IPDM E/R

Connector

Terminal

E13

30

Ground

6 – 16

IPDM E/R

ECM

Continuity

Connector

Terminal

Connector

Terminal

E13

30

F26

66

Existed

IPDM E/R

Ground

Continuity

Connector

Terminal

E13

30

Not existed

Revision: 2013 October

2014 JUKE

SEC-186

< DTC/CIRCUIT DIAGNOSIS >

[WITHOUT INTELLIGENT KEY SYSTEM]

B210E STARTER RELAY

B210E STARTER RELAY

DTC Logic

INFOID:0000000009754794

DTC DETECTION LOGIC

NOTE:
• If DTC B210E is displayed with DTC U1000, first perform the trouble diagnosis for DTC U1000. Refer to

PCS-58, "DTC Logic"

.

• If DTC B210E is displayed with DTC B209F, first perform the trouble diagnosis for DTC B209F. Refer to

SEC-175, "DTC Logic"

.

• If DTC B210E is displayed with DTC B20A0, first perform the trouble diagnosis for DTC B20A0. Refer to

SEC-177, "DTC Logic"

.

• When IPDM E/R power supply voltage is low (Approx. 7 - 8 V for about 1 second), the DTC B210E may be

detected.

DTC CONFIRMATION PROCEDURE

1.

PERFORM DTC CONFIRMATION PROCEDURE

1.

Press push-button ignition switch under the following conditions to start engine, and wait 5 seconds or
more.

-

Selector lever: In the P position

-

Brake pedal: Depressed

2.

Check DTC in “Self Diagnostic Result” mode of “IPDM E/R” using CONSULT.

Is DTC detected?

YES

>> Go to 

SEC-186, "Diagnosis Procedure"

.

NO

>> GO TO 2.

2.

PERFORM DTC CONFIRMATION PROCEDURE 2

1.

Stop engine.

2.

Perform DTC CONFIRMATION PROCEDURE for DTC P1650. Refer to 

EC-470, "DTC Logic"

.

3.

Turn ignition switch ON.

4.

Check DTC in “Self Diagnostic Result” mode of “IPDM E/R” using CONSULT.

Is DTC detected?

YES

>> Refer to 

SEC-186, "Diagnosis Procedure"

.

NO

>> INSPECTION END

Diagnosis Procedure

INFOID:0000000009754795

1.

CHECK STARTER RELAY CONTROL SIGNAL

1.

Turn ignition switch ON.

2.

Check voltage between IPDM E/R harness connector and ground.

DTC No.

Trouble diagnosis name

DTC detecting condition

Possible cause

B210E

STARTER RELAY OFF

When comparing the following items, IPDM 
E/R detects that starter relay is stuck in the 
OFF position for 5 seconds or more.
• Starter control relay control signal (CAN) 

from BCM

• Starter control relay control signal (CAN) 

from ECM

• Starter control relay and starter relay sta-

tus signal (IPDM E/R input)

• Starter control relay control signal (IPDM 

E/R output)

• Ignition switch START signal
• Ignition power supply signal
• Cranking request signal from ECM

• Harness or connector

(CAN communication line is open or 
shorted.)

• Harness or connector

(Starter relay circuit is open or 
shorted.)

• IPDM  E/R
• BCM
• Battery

Revision: 2013 October

2014 JUKE

 

 

 

 

 

 

 

Content      ..     219      220      221      222     ..