Nissan Juke (2014 year). Service Repair Manual - part 162

 

  Index      Manuals     Nissan Juke (2014 year) - Service and Repair Manual

 

Search            copyright infringement  

 

 

 

 

 

 

 

 

Content      ..     160      161      162      163     ..

 

 

Nissan Juke (2014 year). Service Repair Manual - part 162

 

 

INT-20

< REMOVAL AND INSTALLATION >

BODY SIDE TRIM

FRONT KICKING PLATE INNER

1.

Disengage fixing pawls on front lower end of front kicking plate
inner using a remover tool (A).

CAUTION:

Apply protective tape (B) on the parts to protect it from
damage.

2.

Lift up toward vehicle upper and disengage fixing pawls of front
kicking plate inner starting from the front.

CAUTION:

Never lift up excessively. Otherwise, rear end of front kick-
ing plate inner may be damaged.

3.

Lift up lower rear end of front kicking plate inner while pulling it
toward vehicle inside, disengage fixing pawls of front kicking
plate inner, and then remove front kicking plate inner.

REAR KICKING PLATE INNER

1.

Remove rear seat cushion. Refer to 

SE-28, "SEAT CUSHION : Removal and Installation"

.

2.

Disengage fixing pawls on front lower end of rear kicking plate
inner using a remover tool (A).

CAUTION:

Apply protective tape (B) on the parts to protect it from
damage.

: Pawl

: Vehicle front

JMJIA6562ZZ

: Pawl

JMJIA6563ZZ

: Pawl

JMJIA6564ZZ

: Pawl

JMJIA6565ZZ

Revision: 2013 October

2014 JUKE

BODY SIDE TRIM

INT-21

< REMOVAL AND INSTALLATION >

C

D

E

F

G

H

I

K

L

M

A

B

INT

N

O

P

3.

Lift up toward vehicle upper and disengage fixing pawls of rear
kicking plate inner starting from the front.

CAUTION:

Never lift up excessively. Otherwise, rear end of rear kicking
plate inner may be damaged.

4.

Using a remover tool (A), lift up lower rear end of rear kicking
plate inner while disengaging a fixing pawl on lower rear end of
rear kicking plate inner, disengage remaining fixing pawls, and
then remove rear kicking plate inner.

CAUTION:

Apply protective tape (B) on the parts to protect it from
damage.

INSATALLATION

Install in the reverse order of removal.

DASH SIDE FINISHER

DASH SIDE FINISHER : Removal and Installation

INFOID:0000000009750134

REMOVAL

CAUTION:

Never damage the body.

1.

Remove front kicking plate inner. Refer to 

INT-19, "KICKING PLATE INNER : Removal and Installation"

.

2.

Pull back dash side finisher, and then disengage the pawls.

3.

Disconnect dash side finisher, vehicle front side, from stud bolt and remove dash side finisher.

INSTALLATION

Install in the reverse order of removal.

BODY SIDE WELT

BODY SIDE WELT : Removal and Installation

INFOID:0000000009750135

REMOVAL

CAUTION:

• Never excessively pull body side welt.
• Never damage the body.

FRONT BODY SIDE WELT

: Pawl

JMJIA6566ZZ

: Pawl

JMJIA6567ZZ

: Pawl

JMJIA4529ZZ

Revision: 2013 October

2014 JUKE

INT-22

< REMOVAL AND INSTALLATION >

BODY SIDE TRIM

1.

Remove front kicking plate inner. Refer to 

INT-19, "KICKING PLATE INNER : Removal and Installation"

.

2.

Remove front body side welt.

REAR BODY SIDE WELT

1.

Remove rear kicking plate inner. Refer to 

INT-19, "KICKING PLATE INNER : Removal and Installation"

.

2.

Remove rear body side welt.

INSTALLATION

Install in the reverse order of removal.

CENTER PILLAR LOWER GARNISH

CENTER PILLAR LOWER GARNISH : Removal and Installation

INFOID:0000000009750136

REMOVAL

CAUTION:

• When removing, always use a remover tool that is made of plastic.
• Never damage the body.

1.

Fully open front door and rear door.

2.

Slide front seat to the fully forward position. Tilt seatback forward.

3.

Remove Front body side welt and rear body side welt. Refer to 

INT-21, "BODY SIDE WELT : Removal

and Installation"

.

4.

Disengage center pillar lower garnish fixing clips and pawls with
a remover tool (A), and then remove center pillar lower garnish.

INSTALLATION

Note the following item, and install in the reverse order of removal.

CAUTION:

When installing center pillar lower garnish, check that clips are securely in body panel holes, and
press them in.

CENTER PILLAR UPPER GARNISH

CENTER PILLAR UPPER GARNISH : Removal and Installation

INFOID:0000000009750137

REMOVAL

CAUTION:

• When removing, always use a remover tool that is made of plastic.
• Never damage the body.

1.

Remove center pillar lower garnish. Refer to 

INT-22, "CENTER PILLAR LOWER GARNISH : Removal

and Installation"

.

2.

Remove front seat belt shoulder anchor. Refer to 

SB-5, "SEAT BELT RETRACTOR : Removal and Instal-

lation"

.

: Clip

: Pawl

JMJIA4390ZZ

Revision: 2013 October

2014 JUKE

BODY SIDE TRIM

INT-23

< REMOVAL AND INSTALLATION >

C

D

E

F

G

H

I

K

L

M

A

B

INT

N

O

P

3.

Disengage center pillar upper garnish lower side fixing pawl
using a remover tool.

4.

Disengage center pillar upper garnish upper side fixing clip using a remover tool (A).
NOTE:
Removal operation can be performed easily when pressing pawl by inserting a removal tool from direction
(A) as shown in the figure.

CAUTION:

Be careful not to apply excessive force when removing center pillar upper garnish. Otherwise,
pawl may be damaged and fragments may drop in panel holes on body.

INATALLATION

Note the following items, and install in the reverse order of removal.

CAUTION:

• Replace center pillar upper garnish with a new part after removal. Never reuse center pillar upper

garnish.

• When installing center pillar upper garnish, check that pawls are securely in body panel holes, and

press them in.

: Pawl

JMJIA4391ZZ

PIIB7674J

Revision: 2013 October

2014 JUKE

INT-24

< REMOVAL AND INSTALLATION >

FLOOR TRIM

FLOOR TRIM

Exploded View

INFOID:0000000009750138

Removal and Installation

INFOID:0000000009750139

REMOVAL

CAUTION:

• When removing, always use a remover tool that is made of plastic.
• Never damage the body.
1.

Remove front seat assembly (LH and RH). Refer to 

SE-20, "Removal and Installation"

.

2.

Remove rear seat cushion. Refer to 

SE-28, "SEAT CUSHION : Removal and Installation"

.

3.

Remove center console assembly. Refer to 

IP-24, "Removal and Installation"

.

4.

Remove instrument stay.

1.

Floor carpet

2.

Carpet hook

3.

Trim clip

4.

Column hole cover

5.

Harness clip

6.

Front floor spacer RH

7.

Front floor spacer LH

8.

Rear floor spacer LH

9.

Rear floor spacer RH

: Clip

: Pawl

JMJIA4530ZZ

Revision: 2013 October

2014 JUKE

FLOOR TRIM

INT-25

< REMOVAL AND INSTALLATION >

C

D

E

F

G

H

I

K

L

M

A

B

INT

N

O

P

Remove instrument stay mounting nuts (A), and then remove
instrument stay.

5.

Disconnect drain hose. Refer to 

HA-43, "A/C UNIT ASSEMBLY : Removal and Installation"

.

6.

Remove foot ducts (LH and RH). Refer to 

VTL-12, "REAR HEATER DUCT 2 : Removal and Installation"

(Models with foot ducts).

7.

Remove sift selector assembly
• 6MT models: Refer to 

TM-21, "Removal and Installation"

.

• CVT models: Refer to 

TM-307, "Removal and Installation"

.

8.

Remove diagnosis sensor unit. Refer to 

SR-28, "Removal and Installation"

.

9.

Remove parking brake lever. Refer to 

PB-6, "Removal and Installation"

.

10. Remove the inside key antenna (console lower).Refer to 

DLK-173, "CONSOLE : Removal and Installa-

tion"

 (Models with Intelligent Key system).

11. Remove center pillar lower garnish (LH and RH). Refer to 

INT-22, "CENTER PILLAR LOWER GARNISH :

Removal and Installation"

.

12. Remove column hole cover.

Disengage trim clip (A), and then remove column hole cover.

13. Remove dash side finisher (LH and RH). Refer to 

INT-21, "DASH SIDE FINISHER : Removal and Installa-

tion"

.

14. Disengage pawl using a remover tool (A) and open the harness

clip.

15. Remove floor carpet.

NOTE:

: Vehicle front

JMJIA4531ZZ

JMJIA4532ZZ

: Pawl

JMJIA4396ZZ

Revision: 2013 October

2014 JUKE

INT-26

< REMOVAL AND INSTALLATION >

FLOOR TRIM

Disengage pawls using a remover tool and remove carpet hook.

INSTALLATION

Note the following item, and install in the reverse order of removal.

CAUTION:

Replace diagnosis sensor unit fixing bolts with a new part after removal. Never reuse diagnosis sen-
sor unit fixing bolts.

: Pawl

JMJIA3620ZZ

Revision: 2013 October

2014 JUKE

HEADLINING

INT-27

< REMOVAL AND INSTALLATION >

C

D

E

F

G

H

I

K

L

M

A

B

INT

N

O

P

HEADLINING

NORMAL ROOF

NORMAL ROOF : Exploded View

INFOID:0000000009750140

NORMAL ROOF

NORMAL ROOF : Removal and Installation

INFOID:0000000009750141

REMOVAL

JMJIA4533ZZ

1.

Headlining assembly

2.

Assist grip clip

3.

Rear assist grip RH

4.

Front assist grip RH

5.

Sun visor assembly RH

6.

Sun visor cover RH

7.

Sun visor cover LH

8.

Sun visor assembly LH

9.

Rear assist grip LH

10. Headlining clip

11.

Sun visor holder RH

12. Map lamp

13. Sun visor holder LH

14. Metal clip

: Clip

: Pawl

Revision: 2013 October

2014 JUKE

INT-28

< REMOVAL AND INSTALLATION >

HEADLINING

CAUTION:

• When removing, always use a remover tool that is made of plastic.
• Never damage the body.

1.

Remove front pillar garnish (LH and RH). Refer to 

INT-18, "FRONT PILLAR GARNISH : Removal and

Installation"

.

2.

Disconnect harness connector (A) from headlining and harness
clips

3.

Remove center pillar upper garnish (LH and RH). Refer to 

INT-22, "CENTER PILLAR UPPER GARNISH :

Removal and Installation"

.

4.

Remove back door weather-strip. Refer to 

DLK-155, "BACK DOOR WEATHER-STRIP : Removal and

Installation"

 (with Intelligent Key System) or 

DLK-278, "BACK DOOR WEATHER-STRIP : Removal and

Installation"

 (without Intelligent Key System).

5.

Remove luggage side upper finisher (LH and RH). Refer to 

INT-36, "LUGGAGE SIDE UPPER FINISHER

: Removal and Installation"

.

6.

Remove all assist grips.
1.

Disengage pawl of assist grip clip (1) using a remover tool
(A). Slide assist grip clip forward and remove it.

2.

Slide assist grip (2) forward and remove it.

3.

Remove metal clips.

7.

Remove sun visor assembly (LH and RH).
1.

Disengage sun visor cover fixing pawls with a remover tool
(A), and then remove sun visor cover.

2.

Remove sun visor assembly fixing screws, and then slide toward vehicle rear to remove sun visor
assembly.

8.

Remove map lamp assembly. Refer to 

INL-49, "Removal and Installation"

.

9.

Remove front seat assembly (passenger). Refer to 

SE-20, "Removal and Installation"

.

10. Remove sun visor holder (LH and RH).

: Clip

JMJIA4534ZZ

: Pawl

JMJIA4398ZZ

: Pawl

JMJIA4399ZZ

Revision: 2013 October

2014 JUKE

HEADLINING

INT-29

< REMOVAL AND INSTALLATION >

C

D

E

F

G

H

I

K

L

M

A

B

INT

N

O

P

Rotate 90

°

. Remove toward vehicle lower.

11. Remove headlining clips.
12. Remove headlining assembly through the back door.

CAUTION:

• Two workers are required for removal in order to prevent

damage.

• Apply protective tape to the portion where contact may

occur during work.

• Never bend headlining when removing.

INSTALLATION

Note the following items, and install in the reverse order of removal.

CAUTION:

• When installing headlining, start by installing both sun visor holders and headlining clips in order to

keep the headlining in position.

• Never bend headlining when installing.
• Be careful that the surface is not wrinkled when installing.

SUNROOF

JMJIA4401ZZ

JMJIA4402ZZ

Revision: 2013 October

2014 JUKE

INT-30

< REMOVAL AND INSTALLATION >

HEADLINING

SUNROOF : Exploded View

INFOID:0000000009750142

SUNROOF

SUNROOF : Removal and Installation

INFOID:0000000009750143

REMOVAL

CAUTION:

• When removing, always use a remover tool that is made of plastic.

JMJIA4707ZZ

1.

Headlining assembly

2.

Assist grip clip

3.

Rear assist grip RH

4.

Sunroof welt

5.

Front assist grip RH

6.

Sun visor assembly RH

7.

Sun visor cover RH

8.

Sun visor cover LH

9.

Sun visor assembly LH

10. Front roof finisher

11.

Rear assist grip LH

12. Headlining clip

13. Sun visor holder RH

14. Map lamp

15. Sun visor holder LH

16. Metal clip

: Clip

: Pawl

Revision: 2013 October

2014 JUKE

HEADLINING

INT-31

< REMOVAL AND INSTALLATION >

C

D

E

F

G

H

I

K

L

M

A

B

INT

N

O

P

• Never damage the body.

1.

Remove front pillar garnish (LH and RH). Refer to 

INT-18, "FRONT PILLAR GARNISH : Removal and

Installation"

.

2.

Disconnect harness connector (A) from headlining and harness
clips

3.

Remove center pillar upper garnish (LH and RH). Refer to 

INT-22, "CENTER PILLAR UPPER GARNISH :

Removal and Installation"

.

4.

Remove back door weather-strip. Refer to 

DLK-155, "BACK DOOR WEATHER-STRIP : Removal and

Installation"

 (with Intelligent Key System) or 

DLK-278, "BACK DOOR WEATHER-STRIP : Removal and

Installation"

 (without Intelligent Key System).

5.

Remove luggage side upper finisher (LH and RH). Refer to 

INT-36, "LUGGAGE SIDE UPPER FINISHER

: Removal and Installation"

.

6.

Remove all assist grips.
1.

Disengage pawl of assist grip clip (1) using a remover tool
(A). Slide assist grip clip forward and remove it.

2.

Slide assist grip (2) forward and remove it.

3.

Remove metal clips.

7.

Remove sun visor assembly (LH and RH).
1.

Disengage sun visor cover fixing pawls with a remover tool
(A), and then remove sun visor cover.

2.

Remove sun visor assembly fixing screws, and then slide toward vehicle rear to remove sun visor
assembly.

8.

Remove inside mirror and inside mirror cover. Refer to 

MIR-16, "Removal and Installation"

.

9.

Remove map lamp assembly. Refer to 

INL-49, "Removal and Installation"

.

10. Remove sunroof welt.

11. Remove front roof finisher.

: Clip

JMJIA4534ZZ

: Pawl

JMJIA4398ZZ

: Pawl

JMJIA4399ZZ

Revision: 2013 October

2014 JUKE

INT-32

< REMOVAL AND INSTALLATION >

HEADLINING

1.

Disengage front roof finisher fixing pawls with a remover
tool (A).

2.

Disconnect harness connector, and then remove front roof
finisher.

12. Remove front seat assembly (passenger). Refer to 

SE-20, "Removal and Installation"

.

13. Remove sun visor holder (LH and RH)

Rotate 90

°

. Remove toward vehicle lower.

14. Remove headlining clips.
15. Remove headlining assembly through the back door.

CAUTION:

• Two workers are required for removal in order to prevent

damage.

• Apply protective tape to the portion where contact may

occur during work.

• Never bend headlining when removing.

INSTALLATION

Note the following items, and install in the reverse order of removal.

CAUTION:

• When installing headlining, start by installing both sun visor holders and headlining clips in order to

keep the headlining in position.

• Never bend headlining when installing.
• Be careful that the surface is not wrinkled when installing.
• Align sunroof welt connection (A) to (B) when installing sun-

roof welt.

: Pawl

JMJIA4751ZZ

JMJIA4401ZZ

JMJIA4402ZZ

: Vehicle front

JMJIA4708ZZ

Revision: 2013 October

2014 JUKE

LUGGAGE FLOOR TRIM

INT-33

< REMOVAL AND INSTALLATION >

C

D

E

F

G

H

I

K

L

M

A

B

INT

N

O

P

LUGGAGE FLOOR TRIM

Exploded View

INFOID:0000000009750144

2WD models

JMJIA4714ZZ

1.

Rear pillar cap RH

2.

Luggage side upper finisher RH

3.

Luggage side lower finisher RH

4.

Luggage floor board

5.

Luggage side upper finisher LH

6.

Rear pillar cap LH

7.

Seat belt hook LH
(Models with woofer)

8.

Luggage side lower finisher LH
(Models with woofer)

9.

Shock absorber mask LH
(Models with woofer)

10. Luggage floor rear center spacer

(Models with spare tire)

11.

Spare tire clamp
(Models with spare tire)

12. Repair kit holder

(Models without spare tire)

13. Luggage rear plate

14. Luggage side lower finisher grille RH 15. Luggage room lamp

16. Shock absorber mask RH

17. Seat belt hook RH

18. Luggage floor box

19. Seat belt hook LH

20. Luggage side lower finisher LH

21. Shock absorber mask LH

22. Luggage side lower finisher grille LH

: Clip

: Pawl

Revision: 2013 October

2014 JUKE

INT-34

< REMOVAL AND INSTALLATION >

LUGGAGE FLOOR TRIM

AWD models

: Metal clip

: Vehicle front

JMJIA4715ZZ

1.

Rear pillar cap RH

2.

Luggage side upper finisher RH

3.

Luggage side lower finisher RH

4.

Luggage floor board

5.

Luggage side upper finisher LH

6.

Rear pillar cap LH

7.

Seat belt hook LH
(Models with woofer)

8.

Luggage side lower finisher LH
(Models with woofer)

9.

Shock absorber mask LH
(Models with woofer)

10. Luggage rear plate

11.

Luggage side lower finisher grille RH 12. Luggage room lamp

13. Shock absorber mask RH

14. Seat belt hook RH

15. Seat belt hook LH

16. Luggage side lower finisher LH

17. Shock absorber mask LH

18. Luggage side lower finisher grille LH

19. Luggage floor rear spacer LH

20. Spare tire clamp

21. Luggage floor rear spacer RH

: Clip

: Pawl

: Metal clip

: Vehicle front

Revision: 2013 October

2014 JUKE

LUGGAGE FLOOR TRIM

INT-35

< REMOVAL AND INSTALLATION >

C

D

E

F

G

H

I

K

L

M

A

B

INT

N

O

P

LUGGAGE REAR PLATE

LUGGAGE REAR PLATE : Removal and Installation

INFOID:0000000009750145

CAUTION:

• When removing, always use a remover tool that is made of plastic.
• Never damage the body.

REMOVE

1.

Remove back door weather-strip. Refer to 

DLK-155, "BACK DOOR WEATHER-STRIP : Removal and

Installation"

 (with Intelligent Key System) or 

DLK-278, "BACK DOOR WEATHER-STRIP : Removal and

Installation"

 (without Intelligent Key System).

2.

Disengage luggage rear plate fixing metal clip with a remover
tool (A), and then remove luggage rear plate.

INSTALLATION

Note the following items, and install in the reverse order of removal.

CAUTION:

When installing luggage rear plate, check that metal clips are securely in body panel holes, and press
them in.

LUGGAGE SIDE LOWER FINISHER

LUGGAGE SIDE LOWER FINISHER : Removal and Installation

INFOID:0000000009750146

REMOVAL

CAUTION:

• When removing, always use a remover tool that is made of plastic.
• Never damage the body.

1.

Remove luggage room lamp. Refer to 

INL-52, "Removal and Installation"

.

2.

Remove luggage floor board.

3.

Remove luggage floor box (Models with 2WD).

4.

Remove luggage rear plate. Refer to 

INT-35, "LUGGAGE REAR PLATE : Removal and Installation"

.

5.

Remove rear body side welt. Refer to 

INT-21, "BODY SIDE WELT : Removal and Installation"

.

6.

Remove rear seat cushion. Refer to 

SE-28, "SEAT CUSHION : Removal and Installation"

.

7.

Remove rear seat back. Refer to 

SE-29, "SEATBACK : Removal and Installation"

.

8.

Remove side hinge of seatback hinge. Refer to 

SE-34, "SEATBACK HINGE : Removal and Installation"

.

9.

Disengage luggage side lower finisher fixing clips with a
remover tool (A), and then remove luggage side lower finisher.

INSTALLATION

: Metal clip

JMJIA4404ZZ

: Clip

JMJIA4405ZZ

Revision: 2013 October

2014 JUKE

 

 

 

 

 

 

 

Content      ..     160      161      162      163     ..