Nissan Juke (2014 year). Service Repair Manual

EXL-8

< SYSTEM DESCRIPTION >

[HALOGEN TYPE]

SYSTEM

- Ignition switch OFF
- Lighting switch OFF
• IPDM E/R turns the integrated headlamp low relay ON, and turns the headlamp ON according to the low

beam request signal.

• When in any of following conditions, follow me home function can be cancelled while follow me home func-

tion is operating.

Follow me home OFF condition

- Ignition switch is turned from OFF

→

ACC or ON

- Lighting switch is turned from OFF

→

NOTE:
• Flash-to-pass operation illumination time for 1 time can be extended to approximately 30 seconds during

operation of follow me home function.

• Flash-to-pass operation can be illuminated continuously for approximately 60 seconds (flash-to-pass opera-

tion, 2 times), approximately 90 seconds (flash-to-pass operation, 3 times), and a maximum of approxi-
mately 120 seconds (flash-to-pass operation, 4 times).

• Follow me home function activating time can be set by CONSULT. Refer to

EXL-16, "HEADLAMP : CON-

SULT Function (BCM - HEAD LAMP)"

HEADLAMP SYSTEM : Fail-safe

INFOID:0000000009754465

CAN COMMUNICATION CONTROL

When CAN communication with ECM and BCM is impossible, IPDM E/R performs fail-safe control. After CAN
communication recovers normally, it also returns to normal control.

If No CAN Communication Is Available With BCM

AUTO LIGHT SYSTEM

AUTO LIGHT SYSTEM : System Diagram

INFOID:0000000009754466

AUTO LIGHT SYSTEM : System Description

INFOID:0000000009754467

OUTLINE

• Auto light system is controlled by each function of BCM and IPDM E/R.

Control by BCM

- Combination switch reading function

Control part

Fail-safe operation

Headlamp

• Turns ON the headlamp low relay when the ignition switch is turned ON
• Turns OFF the headlamp low relay when the ignition switch is turned OFF
• Headlamp high relay OFF

JMLIA1254GB

Revision: 2013 October

2014 JUKE

SYSTEM

EXL-9

< SYSTEM DESCRIPTION >

[HALOGEN TYPE]

EXL

- Headlamp control function
- Auto light function
- Delay timer function
- Wiper linked auto lighting function

Control by IPDM E/R

- Relay control function
• Auto light system has the auto light function (with twilight lighting function), wiper linked auto lighting function

and delay timer function.

- Auto light function automatically turns ON/OFF the exterior lamps* and each illumination automatically,

depending on the outside brightness.

- Wiper linked auto lighting function automatically turns ON/OFF the exterior lamps* and each illumination

when the light switch is in the AUTO position, according to a front wiper operation.

- When auto light system turns the exterior lamps ON with the ignition switch OFF, delay timer function turns

the exterior lamps OFF, depending on the vehicle condition with the auto light function after a certain period
of time.

*: Headlamp (LO/HI), parking lamp, tail lamp, front fog lamp and side marker lamp (Headlamp HI and front fog
lamp depend on the combination switch condition.)
NOTE:
The settings of the twilight lighting function and the wiper linked auto lighting function can be changed with
CONSULT. Refer to

EXL-16, "HEADLAMP : CONSULT Function (BCM - HEAD LAMP)"

AUTO LIGHT FUNCTION (WITH TWILIGHT LIGHTING FUNCTION)

Description

• BCM detects the combination switch condition with the combination switch reading function.
• BCM supplies voltage to the optical sensor when the ignition switch is turned ON or ACC.
• Optical sensor converts outside brightness (lux) to voltage and transmits the optical sensor signal to BCM.
• BCM filters outside brightness based on the optical sensor signal and judges outside brightness.
• BCM detects change status of outside brightness according to outside brightness from the optical sensor

signal and filtered outside brightness. Based on the change status, BCM judges ON/OFF condition of the
exterior lamp.

• BCM transmits each request signal to IPDM E/R via CAN communication, according to ON/OFF condition by

the auto light function.

NOTE:
As to ON/OFF timing, the sensitivity depends on settings. The settings can be changed with CONSULT. Refer
to

EXL-16, "HEADLAMP : CONSULT Function (BCM - HEAD LAMP)"

WIPER LINKED AUTO LIGHTING FUNCTION

BCM turns the exterior lamps ON when detecting 4 operations of the front wiper work the light switch in AUTO
position.
NOTE:
BCM turns OFF the headlamps 3 seconds after the front wiper switch is turned from ON

⇒

OFF.

DELAY TIMER FUNCTION

BCM turns the exterior lamps OFF depending on the vehicle condition with the auto light function when the
ignition switch is turned OFF.
• Turns the exterior lamps OFF 5 minutes after detecting that any door opens. (Door switch ON).
• Turns the exterior lamps OFF a certain period of time* after closing all doors. (Door switch ON

→

OFF).

• Turns the exterior lamps OFF with the ignition switch ACC or the light switch OFF.
*: The preset time is 45 seconds. The timer operating time can be set by CONSULT. Refer to

EXL-16, "HEAD-

LAMP : CONSULT Function (BCM - HEAD LAMP)"

NOTE:
When any position other than the light switch AUTO is set, the auto light system function switches to the exte-
rior lamp battery saver function.

DAYTIME RUNNING LIGHT SYSTEM

Revision: 2013 October

2014 JUKE

EXL-10

< SYSTEM DESCRIPTION >

[HALOGEN TYPE]

SYSTEM

DAYTIME RUNNING LIGHT SYSTEM : System Diagram

INFOID:0000000009754468

EXCEPT FOR NISMO MODELS

FOR NISMO MODELS

DAYTIME RUNNING LIGHT SYSTEM : System Description

INFOID:0000000009754469

EXCEPT FOR NISMO MODELS

Outline

• Turns the headlamp high ON (high beam at approximately half illumination) as the daytime running light.
• Daytime running light is controlled by daytime running light control function and combination switch reading

function of BCM, and relay control function of IPDM E/R.

Daytime Running Light Operation

• BCM detects the combination switch condition by the combination switch reading function.
• BCM detects the engine condition according to push-button ignition switch*

• BCM detects the engine condition by the engine status signal received from ECM using CAN communica-

tion*

• BCM detects the parking brake condition by the parking brake switch signal received from combination

meter using CAN communication.

• BCM transmits the daytime running light request signal to IPDM E/R using CAN communication according to

the daytime running light ON condition.

Daytime running light ON condition

- Engine running

JMLIA1487GB

JMLIA3997GB

Revision: 2013 October

2014 JUKE

SYSTEM

EXL-11

< SYSTEM DESCRIPTION >

[HALOGEN TYPE]

EXL

- Lighting switch OFF or 1ST
- Parking brake switch OFF
• IPDM E/R controls the daytime running light relay-2 (ground-side) to turn ON according to the daytime run-

ning light request signal.

• Power is supplied from the daytime running light relay 2 through headlamp high (RH) and IPDM E/R to

headlamp high (LH). And high beam headlamps are illuminated (approximately half illumination) as the day-
time running light.

: Only for models with Intelligent Key system

: Only for models without Intelligent Key system

NOTE:
• Daytime running light relay 1 is turned ON when headlamp is low.
• Daytime running light relay 1 is OFF to cut voltage of headlamp low circuit when daytime running light is ON.

FOR NISMO MODELS

Outline

• Daytime running light system is turned on daytime running light.
• Daytime running light is controlled by daytime running light control function and combination switch reading

function of BCM, and relay control function of IPDM E/R.

Daytime Running Light Operation

• BCM detects the combination switch condition by the combination switch reading function.
• BCM detects the engine condition by the engine status signal received from ECM with CAN communication.
• BCM detects the parking brake condition by the parking brake switch signal received from combination

meter with CAN communication.

• BCM detects ENGINE RUNNING condition by engine status signal and RELEASE condition by parking

brake switch signal. And then, BCM transmits the daytime running light request signal to IPDM E/R with
CAN communication according to any of the daytime running light ON condition.

Daytime running light ON condition

- Lighting switch OFF
- Lighting switch AUTO and auto light judgement OFF
• IPDM E/R turns the integrated daytime running light relay ON, and turns the daytime running light ON

according to the daytime running light request signal.

FRONT FOG LAMP SYSTEM

FRONT FOG LAMP SYSTEM : System Diagram

INFOID:0000000009754470

FRONT FOG LAMP SYSTEM : System Description

INFOID:0000000009754471

OUTLINE

Front fog lamp is controlled by combination switch reading function, front fog lamp control function of BCM,
and relay control function of IPDM E/R.

FRONT FOG LAMP OPERATION

• BCM detects the combination switch condition by the combination switch reading function.
• BCM transmits the front fog lights request signal to IPDM E/R via CAN communication according to the front

fog lamp ON condition.

Front fog lamp ON condition

- Front fog lamp switch ON and any of the following. (except for the high beam ON)

JMLIA1154GB

Revision: 2013 October

2014 JUKE

EXL-12

< SYSTEM DESCRIPTION >

[HALOGEN TYPE]

SYSTEM

• Lighting switch 2ND
• Lighting switch AUTO (auto light function ON judgment)
IPDM E/R turns the integrated front fog lamp relay ON, and turns the front fog lamp ON according to the front
fog lights request signal.

FRONT FOG LAMP SYSTEM : Fail-safe

INFOID:0000000009754472

CAN COMMUNICATION CONTROL

When CAN communication with ECM and BCM is impossible, IPDM E/R performs fail-safe control. After CAN
communication recovers normally, it also returns to normal control.

If No CAN Communication Is Available With BCM

TURN SIGNAL AND HAZARD WARNING LAMP SYSTEM

TURN SIGNAL AND HAZARD WARNING LAMP SYSTEM : System Diagram

INFOID:0000000009754473

TURN SIGNAL AND HAZARD WARNING LAMP SYSTEM : System Description

INFOID:0000000009754474

OUTLINE

Turn signal lamp and the hazard warning lamp are controlled by combination switch reading function and the
flasher control function of BCM.

TURN SIGNAL LAMP OPERATION

• BCM detects the combination switch condition by the combination switch reading function.
• BCM supplies voltage to the right (left) turn signal lamp circuit when the ignition switch is ON and the turn

signal switch is in the right (left) position. BCM blinks the turn signal lamp.

HAZARD WARNING LAMP OPERATION

BCM supplies voltage to both turn signal lamp circuits when the hazard switch is ON. BCM blinks the hazard
warning lamp.

TURN SIGNAL INDICATOR LAMP AND TURN SIGNAL OPERATION

• BCM transmits the turn signal indicator lamp signal to the combination meter using CAN communication

while the turn signal lamp and the hazard warning lamp are operating.

• Combination meter outputs the turn signal sound with the integrated buzzer while blinking the turn signal

indicator lamp according to the turn signal indicator lamp signal.

HIGH FLASHER OPERATION

• BCM detects the turn signal lamp circuit status from the current value.

Control part

Fail-safe operation

Front fog lamp

Front fog lamp relay OFF

JPLIA0180GB

Revision: 2013 October

2014 JUKE

SYSTEM

EXL-13

< SYSTEM DESCRIPTION >

[HALOGEN TYPE]

EXL

• BCM increases the turn signal lamp blinking speed if the bulb or harness open is detected with the turn sig-

nal lamp operating.
NOTE:
The blinking speed is normal while operating the hazard warning lamp.

PARKING, LICENSE PLATE, SIDE MARKER AND TAIL LAMP SYSTEM

PARKING, LICENSE PLATE, SIDE MARKER AND TAIL LAMP SYSTEM : System Di-
agram

INFOID:0000000009754475

PARKING, LICENSE PLATE, SIDE MARKER AND TAIL LAMP SYSTEM : System De-
scription

INFOID:0000000009754476

OUTLINE

Parking, license plate, side marker and tail lamps are controlled by combination switch reading function and
headlamp control function of BCM, and relay control function of IPDM E/R.

PARKING, LICENSE PLATE, SIDE MARKER AND TAIL LAMPS OPERATION

• BCM detects the combination switch condition by the combination switch reading function.
• BCM transmits the position light request signal to IPDM E/R and the combination meter via CAN communi-

cation according to the ON/OFF condition of the parking, license plate, side marker and tail lamps.

Parking, license plate, side marker and tail lamps ON condition

- Lighting switch 1ST
- Lighting switch 2ND
- Lighting switch AUTO, and the auto light function ON judgment
- Lighting switch AUTO, with the front fog lamp switch ON and the ignition switch ON*
• IPDM E/R turns the integrated tail lamp relay ON and turns the parking, license plate, side marker and tail

lamps ON according to the position light request signal.

• Combination meter turns the tail lamp indicator lamp ON according to the position light request signal.
*: Only for models with Intelligent Key system

PARKING, LICENSE PLATE, SIDE MARKER AND TAIL LAMP SYSTEM : Fail-safe

INFOID:0000000009754477

CAN COMMUNICATION CONTROL

When CAN communication with ECM and BCM is impossible, IPDM E/R performs fail-safe control. After CAN
communication recovers normally, it also returns to normal control.

If No CAN Communication Is Available With BCM

JMLIA1349GB

Revision: 2013 October

2014 JUKE

EXL-14

< SYSTEM DESCRIPTION >

[HALOGEN TYPE]

SYSTEM

EXTERIOR LAMP BATTERY SAVER SYSTEM

EXTERIOR LAMP BATTERY SAVER SYSTEM : System Diagram

INFOID:0000000009754478

EXTERIOR LAMP BATTERY SAVER SYSTEM : System Description

INFOID:0000000009754479

OUTLINE

• Exterior lamp battery saver system is controlled by each function of BCM and IPDM E/R.

Control by BCM

- Combination switch reading function
- Headlamp control function
- Exterior lamp battery saver function

Control by IPDM E/R

- Relay control function
• BCM turns the exterior lamps* OFF after a period of time to prevent the battery from over-discharge when

the ignition switch is turned OFF with the exterior lamps ON.

*: Headlamp (LO/HI), parking lamp, tail lamp, side marker lamp, license plate lamp and front fog lamp

EXTERIOR LAMP BATTERY SAVER ACTIVATION

BCM activates the timer and turns the exterior lamp OFF 5 minutes after the ignition switch is turned from ON

→

OFF with the exterior lamps ON.

NOTE:
• Headlamp control function turns the exterior lamps ON normally when the ignition switch is turned ACC or

the engine started (both before and after the exterior lamp battery saver is turned OFF).

• The timer starts at the time that the lighting switch is turned from OFF

→

1ST or 2ND with the exterior lamps

OFF.

Control part

Fail-safe operation

• Parking lamp
• License plate lamp
• Illumination
• Tail lamp
• Side marker lamp

• Turns ON the tail lamp relay when the ignition switch is turned ON
• Turns OFF the tail lamp relay when the ignition switch is turned OFF

JPLIA1037GB

Revision: 2013 October

2014 JUKE

DIAGNOSIS SYSTEM (BCM) (WITH INTELLIGENT KEY SYSTEM)

EXL-15

< SYSTEM DESCRIPTION >

[HALOGEN TYPE]

EXL

DIAGNOSIS SYSTEM (BCM) (WITH INTELLIGENT KEY SYSTEM)

COMMON ITEM

COMMON ITEM : CONSULT Function (BCM - COMMON ITEM)

INFOID:0000000010296660

APPLICATION ITEM

CONSULT performs the following functions via CAN communication with BCM.

SYSTEM APPLICATION

BCM can perform the following functions for each system.
NOTE:
It can perform the diagnosis modes except the following for all sub system selection items.

: Applicable item

NOTE:

*: For models with automatic A/C, this diagnosis mode is not used.

FREEZE FRAME DATA (FFD)

The BCM records the following vehicle condition at the time a particular DTC is detected, and displays on
CONSULT.

Diagnosis mode

Function Description

Work Support

Changes the setting for each system function.

Self Diagnostic Result

Displays the diagnosis results judged by BCM.

CAN Diag Support Monitor

Monitors the reception status of CAN communication viewed from BCM.

Data Monitor

The BCM input/output signals are displayed.

Active Test

The signals used to activate each device are forcibly supplied from BCM.

Ecu Identification

The BCM part number is displayed.

Configuration

• Read and save the vehicle specification.
• Write the vehicle specification when replacing BCM.

System

Sub system selection item

Diagnosis mode

Work Support

Data Monitor

Active Test

Door lock

DOOR LOCK

Rear window defogger

REAR DEFOGGER

Warning chime

BUZZER

Interior room lamp timer

INT LAMP

Exterior lamp

HEAD LAMP

Wiper and washer

WIPER

Turn signal and hazard warning lamps

FLASHER

Air conditioning system

AIR CONDITONER

• Intelligent Key system
• Engine start system

INTELLIGENT KEY

Combination switch

COMB SW

Body control system

BCM

NVIS - NATS

IMMU

Interior room lamp battery saver

BATTERY SAVER

Back door open

TRUNK

Theft warning alarm

THEFT ALM

RAP

RETAINED PWR

Signal buffer system

SIGNAL BUFFER

TPMS

AIR PRESSURE MONITOR

Revision: 2013 October

2014 JUKE

EXL-16

< SYSTEM DESCRIPTION >

[HALOGEN TYPE]

DIAGNOSIS SYSTEM (BCM) (WITH INTELLIGENT KEY SYSTEM)

NOTE:

*: Power position shifts to “LOCK” from “OFF”, when ignition switch is in the OFF position, selector lever is in the P position (A/T models
and CVT models), and any of the following conditions are met.

• Closing door

• Opening door

• Door is locked using door request switch

• Door is locked using Intelligent Key

The power position shifts to “ACC” when the push-button ignition switch (push switch) is pushed at “LOCK”.

HEADLAMP

HEADLAMP : CONSULT Function (BCM - HEAD LAMP)

INFOID:0000000009754481

WORK SUPPORT

CONSULT screen item

Indication/Unit

Description

Vehicle Speed

km/h

Vehicle speed of the moment a particular DTC is detected

Odo/Trip Meter

Total mileage (Odometer value) of the moment a particular DTC is detected

Vehicle Condition

SLEEP>LOCK

Power position status of
the moment a particular
DTC is detected

While turning BCM status from low power consumption mode to
normal mode (Power position is “LOCK”*.)

SLEEP>OFF

While turning BCM status from low power consumption mode to
normal mode (Power position is “OFF”.)

LOCK>ACC

While turning power position from “LOCK”* *to “ACC”

ACC>ON

While turning power position from “ACC” to “IGN”

RUN>ACC

While turning power position from “RUN” to “ACC” (Vehicle is
stopping and selector lever is except P position.)

CRANK>RUN

While turning power position from “CRANKING” to “RUN” (From
cranking up the engine to run it)

RUN>URGENT

While turning power position from “RUN“ to “ACC” (Emergency
stop operation)

ACC>OFF

While turning power position from “ACC” to “OFF”

OFF>LOCK

While turning power position from “OFF” to “LOCK”*

OFF>ACC

While turning power position from “OFF” to “ACC”

ON>CRANK

While turning power position from “IGN” to “CRANKING”

OFF>SLEEP

While turning BCM status from normal mode (Power position is
“OFF”.) to low power consumption mode

LOCK>SLEEP

While turning BCM status from normal mode (Power position is
“LOCK”*.) to low power consumption mode

LOCK

Power position is “LOCK”*

OFF

Power position is “OFF” (Ignition switch OFF)

ACC

Power position is “ACC” (Ignition switch ACC)

Power position is “IGN” (Ignition switch ON with engine stopped)

ENGINE RUN

Power position is “RUN” (Ignition switch ON with engine running)

CRANKING

Power position is “CRANKING” (At engine cranking)

IGN Counter

0 - 39

The number of times that ignition switch is turned ON after DTC is detected
• The number is 0 when a malfunction is detected now.
• The number increases like 1

→

3...38

→

39 after returning to the normal condition

whenever ignition switch OFF

→

ON.

• The number is fixed to 39 until the self-diagnosis results are erased if it is over 39.

Revision: 2013 October

2014 JUKE

DIAGNOSIS SYSTEM (BCM) (WITH INTELLIGENT KEY SYSTEM)

EXL-17

< SYSTEM DESCRIPTION >

[HALOGEN TYPE]

EXL

: For models without auto light system, this item is displayed, but cannot be used.

: Factory setting

DATA MONITOR

NOTE:
The following table includes information (items) inapplicable to this vehicle. For information (items) applicable
to this vehicle, refer to CONSULT display items.

Service item

Setting item

Setting

CUSTOM A/LIGHT SET-

TING*

MODE 1*

Normal

MODE 2

More sensitive setting than normal setting (Turns ON earlier than normal opera-
tion)

MODE 3

More sensitive setting than MODE 2 (Turns ON earlier than MODE 2)

MODE 4

Less sensitive setting than normal setting (Turns ON later than normal operation)

BATTERY SAVER SET

On*

With the exterior lamp battery saver function

Off

Without the exterior lamp battery saver function

ILL DELAY SET*

MODE 1*

45 sec.

Sets delay timer function timer operation time
(All doors closed)

MODE 2

Without the
function

MODE 3

30 sec.

MODE 4

60 sec.

MODE 5

90 sec.

MODE 6

120 sec.

MODE 7

150 sec.

MODE 8

180 sec.

HEAD LIGHT TIMER

MODE 1

10 sec.

Sets follow me home function activating time

MODE 2

30 sec.

AUTO LIGHT LOGIC SET*

MODE 1*

With twilight ON custom & with wiper INT, LO and HI

MODE 2

With twilight ON custom & with wiper LO and HI

MODE 3

With twilight ON custom & without

MODE 4

Without twilight ON custom & with wiper INT, LO and HI

MODE 5

Without twilight ON custom & with wiper LO and HI

MODE 6

Without twilight ON custom & without

Monitor item

[Unit]

Description

PUSH SW
[On/Off]

Indicates [On/Off] condition of push-button ignition switch

ENGINE STATE
[Stop/Stall/Crank/Run]

Indicates [Stop/Stall/Crank/Run] condition of engine states

VEH SPEED 1
[km/h]

Display the vehicle speed signal received from combination meter by numerical value
[Km/h]

Revision: 2013 October

2014 JUKE

EXL-18

< SYSTEM DESCRIPTION >

[HALOGEN TYPE]

DIAGNOSIS SYSTEM (BCM) (WITH INTELLIGENT KEY SYSTEM)

*: For models without front fog lamp, this item is displayed, but cannot be monitored.

ACTIVE TEST

TURN SIGNAL R
[On/Off]

Each switch status that BCM judges from the combination switch reading function

TURN SIGNAL L
[On/Off]

TAIL LAMP SW
[On/Off]

HI BEAM SW
[On/Off]

HEAD LAMP SW1
[On/Off]

HEAD LAMP SW2
[On/Off]

PASSING SW
[On/Off]

AUTO LIGHT SW
[On/Off]

FR FOG SW*
[On/Off]

DOOR SW-DR
[On/Off]

Indicated [On/Off] condition of front door switch (driver side)

DOOR SW-AS
[On/Off]

Indicated [On/Off] condition of front door switch (passenger side)

DOOR SW-RR
[On/Off]

Indicated [On/Off] condition of rear door switch RH

DOOR SW- RL
[On/Off]

Indicated [On/Off] condition of rear door switch LH

DOOR SW-BK
[On/Off]

Indicated [On/Off] condition of back door switch

OPTICAL SENSOR
[On/Off/NG]

NOTE:
This item is displayed, but cannot be monitored

OPTI SEN (DTCT)
[V]

The value of outside brightness voltage input from the optical sensor

OPTI SEN (FILT)
[V]

The value of outside brightness voltage filtered by BCM

Monitor item

[Unit]

Description

Test item

Operation

Description

TAIL LAMP

Transmits the position light request signal to IPDM E/R via CAN commu-
nication to turn the tail lamp ON

Off

Stops the tail lamp request signal transmission

HEAD LAMP

Transmits the high beam request signal via CAN communication to turn
the headlamp (HI)

Transmits the low beam request signal via CAN communication to turn
the headlamp (LO)

Off

Stops the high & low beam request signal transmission

Revision: 2013 October

2014 JUKE

DIAGNOSIS SYSTEM (BCM) (WITH INTELLIGENT KEY SYSTEM)

EXL-19

< SYSTEM DESCRIPTION >

[HALOGEN TYPE]

EXL

: Except for NISMO models without front fog lamp, this item is displayed, but cannot be tested.

: For NISMO models with daytime running light system, this item is displayed, but cannot be tested.

: Except for NISMO models with daytime running light system.

: For NISMO models with daytime running light system.

FLASHER

FLASHER : CONSULT Function (BCM - FLASHER)

INFOID:0000000009754482

WORK SUPPORT

*: Factory setting

DATA MONITOR

NOTE:
The following table includes information (items) inapplicable to this vehicle. For information (items) applicable
to this vehicle, refer to CONSULT display items.

FR FOG LAMP*

• Transmits the front fog lights request signal to IPDM E/R via CAN com-

munication to turn the front fog lamp ON*

• Transmits the daytime running light request signal to IPDM E/R via

CAN communication to turn the daytime running light ON*

Off

• Stops the front fog light request signal transmission*

• Stops the daytime running light request signal transmission*

DAYTIME RUNNING LIGHT*

Transmits the daytime running light request signal via CAN communica-
tion to IPDM E/R

Off

Stop the daytime running light request signal transmission

ILL DIM SIGNAL

NOTE:
This item is indicated, but can not tested

Off

Test item

Operation

Description

Service item

Setting item

Setting

HAZARD ANSWER
BACK

Lock Only

With locking only

Sets the hazard warning lamp answer back function
when the door is lock/unlock with the request switch or
the Intelligent Key.

Unlk Only

With unlocking only

Lock&Unlk

With locking/unlocking

Off

Without the function

Monitor item

[Unit]

Description

REQ SW-DR
[On/Off]

Indicated [On/Off] condition of door request switch (driver side)

REQ SW-AS
[On/Off]

Indicated [On/Off] condition of door request switch (passenger side)

PUSH SW
[On/Off]

Indicates [On/Off] condition of push-button ignition switch

TURN SIGNAL R
[On/Off]

Each switch status that BCM detects from the combination switch reading function

TURN SIGNAL L
[On/Off]

HAZARD SW
[On/Off]

The switch status input from the hazard switch

RKE-LOCK
[On/Off]

Indicates [On/Off] condition of LOCK signal from Intelligent Key

Revision: 2013 October

2014 JUKE

DIAGNOSIS SYSTEM (BCM) (WITHOUT INTELLIGENT KEY SYSTEM)

EXL-21

< SYSTEM DESCRIPTION >

[HALOGEN TYPE]

EXL

DIAGNOSIS SYSTEM (BCM) (WITHOUT INTELLIGENT KEY SYSTEM)

COMMON ITEM

COMMON ITEM : CONSULT Function (BCM - COMMON ITEM)

INFOID:0000000010296662

APPLICATION ITEM

CONSULT performs the following functions via CAN communication with BCM.

SYSTEM APPLICATION

BCM can perform the following functions for each system.
NOTE:
It can perform the diagnosis modes except the following for all sub system selection items.

: Applicable item

HEADLAMP

HEADLAMP : CONSULT Function (BCM - HEAD LAMP)

INFOID:0000000009754484

WORK SUPPORT

Diagnosis mode

Function Description

Work Support

Changes the setting for each system function.

Self Diagnostic Result

Displays the diagnosis results judged by BCM.

CAN Diag Support Monitor

Monitors the reception status of CAN communication viewed from BCM.

Data Monitor

The BCM input/output signals are displayed.

Active Test

The signals used to activate each device are forcibly supplied from BCM.

Ecu Identification

The BCM part number is displayed.

Configuration

• Read and save the vehicle specification.
• Write the vehicle specification when replacing BCM.

System

Sub system selection item

Diagnosis mode

Work Support

Data Monitor

Active Test

Door lock

DOOR LOCK

Rear window defogger

REAR DEFOGGER

Warning chime

BUZZER

Interior room lamp control

INT LAMP

Remote keyless entry system

MULTI REMOTE ENT

Exterior lamp

HEAD LAMP

Wiper and washer

WIPER

Turn signal and hazard warning lamps

FLASHER

Air conditioning system

AIR CONDITONER

Combination switch

COMB SW

Body control system

BCM

NATS

IMMU

Interior room lamp battery saver

BATTERY SAVER

Back door open

TRUNK

Theft warning alarm

THEFT ALM

RAP system

RETAINED PWR

Signal buffer system

SIGNAL BUFFER

Panic alarm

PANIC ALARM

TPMS

AIR PRESSUE MONITOR

Revision: 2013 October

2014 JUKE

EXL-22

< SYSTEM DESCRIPTION >

[HALOGEN TYPE]

DIAGNOSIS SYSTEM (BCM) (WITHOUT INTELLIGENT KEY SYSTEM)

*: Factory setting

DATA MONITOR

NOTE:
The following table includes information (items) inapplicable to this vehicle. For information (items) applicable
to this vehicle, refer to CONSULT display items.

Service item

Setting item

Setting

BATTERY SAVER SET

On*

With the exterior lamp battery saver function

Off

Without the exterior lamp battery saver function

ILL DELAY SET

MODE 1

NOTE:
This item is displayed but is not operated

MODE 2

MODE 3

MODE 4

MODE 5

MODE 6

MODE 7

MODE 8

HEAD LIGHT TIMER

MODE 1

10 sec.

Sets follow me home function activating time

MODE 2

30 sec.

AUTO LIGHT LOGIC SET

MODE 1

NOTE:
This item is displayed but is not operated

MODE 2

MODE 3

MODE 4

MODE 5

MODE 6

Monitor item

[Unit]

Description

IGN ON SW
[On/Off]

Indicated [On/Off] condition of ignition switch in ON position

ACC ON SW
[On/Off]

Indicates [On/Off] condition of ignition switch in ACC position

VEHICLE SPEED
[km/h]

Display the vehicle speed signal received from combination meter by numerical value
[Km/h]

HI BEAM SW
[On/Off]

Each switch status that BCM judges from the combination switch reading function

HEAD LAMP SW1
[On/Off]

HEAD LAMP SW2
[On/Off]

PASSING SW
[On/Off]

FR FOG SW*
[On/Off]

AUTO LIGHT SW
[On/Off]

NOTE:
This item is indicated, but can not monitored

DOOR SW-DR
[On/Off]

The switch status input from front door switch (driver side)

DOOR SW-AS
[On/Off]

The switch status input from front door switch (passenger side)

Revision: 2013 October

2014 JUKE

DIAGNOSIS SYSTEM (BCM) (WITHOUT INTELLIGENT KEY SYSTEM)

EXL-23

< SYSTEM DESCRIPTION >

[HALOGEN TYPE]

EXL

*: For models without front fog lamp, this item is displayed but is not monitored.

ACTIVE TEST

: For models without front fog lamp, this item is displayed but is not tested.

: For models without daytime running light system, this item is not displayed.

FLASHER

DOOR SW-RR
[On/Off]

The switch status input from rear door switch RH

DOOR SW- RL
[On/Off]

The switch status input from rear door switch LH

BACK DOOR SW
[On/Off]

The switch status input from back door switch

TURN SIGNAL R
[On/Off]

Each switch status that BCM judges from the combination switch reading function

TURN SIGNAL L
[On/Off]

TAIL LAMP SW
[On/Off]

KEY ON SW
[On/Off]

Indicated [On/Off] condition of key switch

KEYLESS LOCK
[On/Off]

Indicated [On/Off] condition of lock signal from key fob

PKB SW
[On/Off]

The parking brake switch status received from combination meter with CAN commu-
nication

ENGINE RUN
[On/Off]

The engine status received from ECM with CAN communication

OPTI SEN (DTCT)
[V]

NOTE:
This item is indicated, but can not monitored

OPTI SEN (FILT)
[V]

NOTE:
This item is indicated, but can not monitored

LIG SEN COND
[On/Off/NG]

NOTE:
This item is indicated, but can not monitored

Monitor item

[Unit]

Description

Test item

Operation

Description

TAIL LAMP

Transmits the position light request signal to IPDM E/R with CAN com-
munication to turn the tail lamp ON

Off

Stops the tail lamp request signal transmission

HEAD LAMP

Transmits the high beam request signal with CAN communication to turn
the headlamp (HI)

Transmits the low beam request signal with CAN communication to turn
the headlamp (LO)

Off

Stops the high & low beam request signal transmission

FR FOG LAMP*

Transmits the front fog lights request signal to IPDM E/R with CAN com-
munication to turn the front fog lamp ON

Off

Stops the front fog lights request signal transmission

DAYTIME RUNNING LIGHT*

Transmits the daytime running light request signal via CAN communica-
tion to IPDM E/R

Off

Stop the daytime running light request signal transmission

ILL DIM SIGNAL

NOTE:
This item is indicated, but can not tested

Off

Revision: 2013 October

2014 JUKE

Nissan Juke (2014 year). Service Repair Manual - part 124