Nissan Juke (2014 year). Service Repair Manual - part 66

 

  Index      Manuals     Nissan Juke (2014 year) - Service and Repair Manual

 

Search            copyright infringement  

 

 

 

 

 

 

 

 

Content      ..     64      65      66      67     ..

 

 

Nissan Juke (2014 year). Service Repair Manual - part 66

 

 

HOOD LOCK

DLK-281

< REMOVAL AND INSTALLATION >

[WITHOUT INTELLIGENT KEY SYSTEM]

C

D

E

F

G

H

I

J

L

M

A

B

DLK

N

O

P

Note the following items, and install in the reverse order of removal.

CAUTION:

• Check that hood lock control cable is properly engaged with hood lock.
• After installation, perform hood fitting adjustment. Refer to 

DLK-252, "HOOD ASSEMBLY : Adjust-

ment"

.

• After installation, perform hood lock control inspection. Refer to 

DLK-281, "Inspection"

.

HOOD LOCK CONTROL CABLE

HOOD LOCK CONTROL CABLE : Removal and Installation

INFOID:0000000009754214

REMOVAL

1.

Disconnect hood lock control cable assembly from hood lock assembly.

2.

Remove fender protector (LH). Refer to 

EXT-27, "Removal and Installation"

.

3.

Remove hood lock cable clip.

4.

Remove hood lock control cable assembly of instrument lower
panel (LH), and then remove fuel filler lid opener cable (2) from
fuel filler lid opener lever (1).

5.

Remove grommet on the lower dash, and pull the hood lock control cable toward the passenger compart-
ment.

CAUTION:

While pulling, never to damage (peeling) the outside of hood lock control cable.

INSTALLATION

Note the following items, and install in the reverse order of removal.

CAUTION:

• Never to bend cable too much, keeping the radius 100 mm (3.937 in) or more.
• Check that cable is not offset from the positioning grommet,

and apply the sealant to the grommet (at * mark) properly.

• Check that hood lock control cable is properly engaged with hood lock.
• After installation, perform hood fitting adjustment. Refer to 

DLK-252, "HOOD ASSEMBLY : Adjust-

ment"

.

• After installation, perform hood lock control inspection. Refer to 

DLK-281, "Inspection"

.

Inspection

INFOID:0000000009754215

NOTE:
If the hood lock cable is bent or deformed, replace it.

1.

Check that secondary latch is securely engaged with securely striker from the dead load of the hood
assembly.

JMKIA5901ZZ

PIIB5801E

Revision: 2013 October

2014 JUKE

DLK-282

< REMOVAL AND INSTALLATION >

[WITHOUT INTELLIGENT KEY SYSTEM]

HOOD LOCK

2.

Check that primary latch is securely engaged with primary striker when hood assembly is closed [free-fall
from approximately 200 mm (7.874 in) height].

CAUTION:

Never free-fall hood assembly from a height of 300 (11.811 in) mm or more.

3.

While operating the hood opener carefully, check that the front end of the hood is lifted by approximately
20 mm (0.787 in) (A). Also, check that the hood opener returns to the original position.

4.

Check that secondary latch is properly engaged with secondary striker [6.8 mm (0.268 in)] (B).

5.

Check the hood lock lubrication condition. If necessary, apply
body grease to hood lock.

1.

Primary striker

2.

Primary latch

3.

Secondary latch

4.

Secondary striker

: Grease up point

JMKIA5673ZZ

JMKIA5674ZZ

Revision: 2013 October

2014 JUKE

FRONT DOOR LOCK

DLK-283

< REMOVAL AND INSTALLATION >

[WITHOUT INTELLIGENT KEY SYSTEM]

C

D

E

F

G

H

I

J

L

M

A

B

DLK

N

O

P

FRONT DOOR LOCK

Exploded View

INFOID:0000000009754216

DOOR LOCK

DOOR LOCK : Removal and Installation

INFOID:0000000009754217

REMOVAL

1.

Remove front door glass and front door lower sash (rear). Refer to 

GW-17, "Removal and Installation"

.

2.

Remove inside handle. Refer to 

DLK-284, "INSIDE HANDLE : Removal and Installation"

.

3.

Disengage inside handle cable and lock knob cable from cable clip.

4.

Remove outside handle bracket. Refer to 

DLK-284, "OUTSIDE HANDLE : Removal and Installation"

.

5.

Remove door lock assembly TORX bolts.

6.

Disconnect door lock actuator connector, and then remove door lock assembly.

1.

Door key cylinder assembly (driver 
side)
Outside handle escutcheon (passen-
ger side)

2.

Rear gasket

3.

Outside handle bracket

4.

TORX bolt

5.

Key rod (driver side)

6.

Door lock assembly

7.

Inside handle

8.

Outside handle

9.

Front gasket

10. Cable clip

: Pawl 

: Vehicle front

: Do not reuse

: N·m (kg-m, in-lb)

: Body grease

JMKIA5883GB

Revision: 2013 October

2014 JUKE

DLK-284

< REMOVAL AND INSTALLATION >

[WITHOUT INTELLIGENT KEY SYSTEM]

FRONT DOOR LOCK

INSTALLATION

Note the following items, and install in the reverse order of removal.

CAUTION:

• Never reuse TORX bolt. Always replace it with a new one when it is removed.
• Check door open/close, lock/unlock operation after installation. 
• Check door lock cable is properly engaged with outside handle bracket.
• Check door lock assembly for poor lubrication. Apply body

grease to door lock if necessary.

INSIDE HANDLE

INSIDE HANDLE : Removal and Installation

INFOID:0000000009754218

REMOVAL

1.

Remove front door finisher. Refer to 

INT-13, "Removal and Installation"

.

2.

Remove inside handle mounting bolt (A).

3.

Disengage inside handle (1) from door panel (2) while sliding
inside handle toward vehicle rear, and then separate inside han-
dle.

4.

Disengage inside handle cable (3) and lock knob cable (2), and
then remove inside handle (1).

INSTALLATION

Note the following item, and install in the reverse order of removal.

CAUTION:

Check door open/close, lock/unlock operation after installation.

OUTSIDE HANDLE

OUTSIDE HANDLE : Removal and Installation

INFOID:0000000009754219

REMOVAL

1.

Fully close the front door glass.

2.

Remove front door finisher. Refer to 

INT-13, "Removal and Installation"

.

: Grease up point

JMKIA5892ZZ

: Vehicle front

JMKIA5884ZZ

JMKIA5885ZZ

Revision: 2013 October

2014 JUKE

FRONT DOOR LOCK

DLK-285

< REMOVAL AND INSTALLATION >

[WITHOUT INTELLIGENT KEY SYSTEM]

C

D

E

F

G

H

I

J

L

M

A

B

DLK

N

O

P

3.

Remove sealing screen.
NOTE:
Cut the butyl-tape so that some parts of the butyl-tape do not remain on the sealing screen, if the sealing
screen is reused. 

4.

Disengage lock holder (1), and then separate key rod (3) from
door lock assembly (2).(Driver side)

5.

Remove grommet (1) of door side. Loosen, through grommet
hole, TORX bolt (2) that fixes door lock cylinder. (For passenger
side, TORX bolt fixes outside handle escutcheon.)

6.

While pulling outside handle, remove door key cylinder assem-
bly (diver side) or outside handle escutcheon (passenger side).

7.

While pulling outside handle (1), slide toward rear of vehicle to
remove outside handle.

JMKIA5886ZZ

JMKIA5888ZZ

JMKIA0560ZZ

JMKIA0524ZZ

Revision: 2013 October

2014 JUKE

DLK-286

< REMOVAL AND INSTALLATION >

[WITHOUT INTELLIGENT KEY SYSTEM]

FRONT DOOR LOCK

8.

Remove front gasket (1) and rear gasket (2).

9.

Slide outside handle bracket toward rear of vehicle to remove.

10. Disconnect outside handle cable (1) from outside handle bracket

(2).

INSTALLATION

Note the following items, and install in the reverse order of removal.

CAUTION:

• When installing key rod, rotate key rod holder until a click is felt.
• Check that door lock cables are normally engaged with inside handle and outside handle.
• After installation, check door open/close, and lock/unlock operation.

: Vehicle front

JMKIA5889ZZ

: Vehicle front

JMKIA5890ZZ

JMKIA5891ZZ

Revision: 2013 October

2014 JUKE

REAR DOOR LOCK

DLK-287

< REMOVAL AND INSTALLATION >

[WITHOUT INTELLIGENT KEY SYSTEM]

C

D

E

F

G

H

I

J

L

M

A

B

DLK

N

O

P

REAR DOOR LOCK

Exploded View

INFOID:0000000009754220

DOOR LOCK

DOOR LOCK : Removal and Installation

INFOID:0000000009754221

REMOVAL

1.

Remove rear door glass and rear door lower sash (rear). Refer to 

GW-21, "Removal and Installation"

.

2.

Remove inside handle. Refer to 

DLK-288, "INSIDE HANDLE : Removal and Installation"

.

3.

Remove outside handle. Refer to 

DLK-288, "OUTSIDE HANDLE : Removal and Installation"

.

4.

Remove door lock assembly TORX bolts.

5.

Disconnect door lock actuator connector, and then remove door lock assembly.

INSTALLATION

Note the following items, and install in the reverse order of removal.

CAUTION:

• Never reuse TORX bolt. Always replace it with a new one when it is removed.
• Check door open/close, lock/unlock operation after installation. 

1.

Outside handle assembly

2.

Rear door sealing screen

3.

Door lock assembly

4.

TORX bolt

5.

Inside handle

: Clip

: Pawl

: Vehicle front

: Do not reuse

: N·m (kg-m, in-lb)

: Body grease

JMKIA5893GB

Revision: 2013 October

2014 JUKE

DLK-288

< REMOVAL AND INSTALLATION >

[WITHOUT INTELLIGENT KEY SYSTEM]

REAR DOOR LOCK

• Check door lock assembly for poor lubrication. Apply body

grease to door lock if necessary.

INSIDE HANDLE

INSIDE HANDLE : Removal and Installation

INFOID:0000000009754222

REMOVAL

1.

Remove rear door finisher. Refer to 

INT-16, "Removal and Installation"

.

2.

Remove upper side of sealing screen.
NOTE:
Cut the butyl tape so that some parts of the butyl tape do not remain on the sealing screen, if the sealing
screen is reused.

3.

Remove inside handle mounting bolt (A).

4.

Disengage inside handle (1) from door panel (2) while sliding
inside handle toward vehicle rear, and then separate inside han-
dle.

5.

Disengage inside handle cable (3) and lock knob cable (2), and
then remove inside handle (1).

INSTALLATION

Note the following item, and install in the reverse order of removal.

CAUTION:

Check door open/close, lock/unlock operation after installation. 

OUTSIDE HANDLE

OUTSIDE HANDLE : Removal and Installation

INFOID:0000000009754223

REMOVAL

1.

Remove rear door finisher and rear door corner cover inner. Refer to 

INT-16, "Removal and Installation"

.

2.

Remove rear door sealing screen. 

: Grease up point

JMKIA5892ZZ

: Vehicle front

JMKIA5884ZZ

JMKIA5885ZZ

Revision: 2013 October

2014 JUKE

REAR DOOR LOCK

DLK-289

< REMOVAL AND INSTALLATION >

[WITHOUT INTELLIGENT KEY SYSTEM]

C

D

E

F

G

H

I

J

L

M

A

B

DLK

N

O

P

3.

Rotate stopper (1) upward.

4.

Disengage outside handle cable (2), and then remove outside
handle cable from outside handle assembly (3).

5.

Remove outside handle assembly mounting bolts (A).

6.

Disengage mounting clips using a remover tool (A), and then
remove outside handle assembly.

CAUTION:

Apply protective tape (B) on the door panel to protect the
painted surface from damage.

INSTALLATION

Note the following items, and install in the reverse order of removal.

CAUTION:

• Never reuse rear door sealing screen. Always replace it with a new one when it is removed.

When installing rear door sealing screen, install it according to the following procedure.

- Put lower portion of rear door sealing screen (1) into inside of

door panel (2).

- Perform positioning according to the following procedure,

and then install rear door sealing screen.

• Align upper portion of rear door sealing screen to hole (A) of

door panel as shown in the figure.

• Align hole of rear door sealing screen to edge (B) of door

panel as shown in the figure.

• Be careful to position outside handle cable normally when installing it. For details, refer to 

DLK-287,

"Exploded View"

.

• Check door open/close, lock/unlock operation after installation. 

JMKIA5894ZZ

JMKIA5895ZZ

: Clip

JMKIA5896ZZ

JMKIA5897ZZ

Revision: 2013 October

2014 JUKE

DLK-290

< REMOVAL AND INSTALLATION >

[WITHOUT INTELLIGENT KEY SYSTEM]

BACK DOOR LOCK

BACK DOOR LOCK

Exploded View

INFOID:0000000009754224

DOOR LOCK

DOOR LOCK : Removal and Installation

INFOID:0000000009754225

REMOVAL

1.

Remove the back door lower finisher. Refer to 

INT-39, "BACK DOOR LOWER FINISHER : Removal and

Installation"

.

2.

Remove back door lock assembly mounting bolts.

3.

Disconnect back door lock connector, and then remove back door lock assembly.

INSTALLATION

Note the following item, and install in the reverse order of removal.

CAUTION:

After installation, check back door open/close, and lock/unlock operation.

EMERGENCY LEVER

EMERGENCY LEVER : Unlock procedures

INFOID:0000000009754226

UNLOCK PROCEDURES

NOTE:
If back door lock cannot be unlocked due to a malfunction or battery discharge, follow the procedures to
unlock back door.

1.

Remove emergency lid. Refer to 

INT-40, "EMERGENCY LID : Removal and Installation"

.

1.

Back door lock assembly

2.

TORX bolt

3.

Back door striker

: Do not reuse

: N·m (kg-m, ft-lb)

: Body grease

JMKIA5714GB

Revision: 2013 October

2014 JUKE

BACK DOOR LOCK

DLK-291

< REMOVAL AND INSTALLATION >

[WITHOUT INTELLIGENT KEY SYSTEM]

C

D

E

F

G

H

I

J

L

M

A

B

DLK

N

O

P

2.

From inside the vehicle, rotate emergency lever toward lower
direction and unlock.

JMKIA5616ZZ

Revision: 2013 October

2014 JUKE

DLK-292

< REMOVAL AND INSTALLATION >

[WITHOUT INTELLIGENT KEY SYSTEM]

FUEL FILLER LID OPENER

FUEL FILLER LID OPENER

Exploded View

INFOID:0000000009754227

FUEL FILLER LID

FUEL FILLER LID : Removal and Installation

INFOID:0000000009754228

REMOVAL 

1.

Fully open fuel filler lid. 

2.

Remove fuel mounting pin (1).

3.

Remove mounting screws, and then remove fuel filler lid.

INSTALLATION 

Note the following items, and install in the reverse order of removal.

1.

Fuel filler lid opener cable

2.

Cable protector

3.

Fuel filler lid lock assembly

4.

Fuel filler lid assembly

5.

Spring

6.

Bumper rubber

: Clip

: Do not reuse

JMKIA5904ZZ

JMKIA5717ZZ

Revision: 2013 October

2014 JUKE

FUEL FILLER LID OPENER

DLK-293

< REMOVAL AND INSTALLATION >

[WITHOUT INTELLIGENT KEY SYSTEM]

C

D

E

F

G

H

I

J

L

M

A

B

DLK

N

O

P

CAUTION:

• After installation, check fuel filler lid assembly open/close, lock/unlock operation.
• After installation, apply the touch-up paint (the body color) onto the head of the mounting screws.
NOTE:
• The following table shows the specifide values for checking nomal installation status.
• Fitting adjustment cannot be perfomed.

Unit: mm (in)

FUEL FILLER OPENER CABLE

FUEL FILLER OPENER CABLE : Removal and Installation

INFOID:0000000009754229

REMOVAL 

1.

Remove hood lock control cable assembly from instrument lower panel (LH). Refer to 

DLK-281, "HOOD

LOCK CONTROL CABLE : Removal and Installation"

.

2.

Remove fuel filler lid opener cable (2) from fuel filler lid opener
lever (1).

3.

Remove front kicking plate inner (LH) and rear kicking plate inner (LH and RH). Refer to 

INT-19, "KICK-

ING PLATE INNER : Removal and Installation"

.

4.

Remove dash side finisher (LH). Refer to 

INT-21, "DASH SIDE FINISHER : Removal and Installation"

.

5.

Remove center pillar lower garnish (LH). Refer to 

INT-22, "CENTER PILLAR LOWER GARNISH :

Removal and Installation"

.

6.

Remove luggage side lower finisher (RH). Refer to 

INT-35, "LUGGAGE SIDE LOWER FINISHER :

Removal and Installation"

.

7.

Remove fuel filler lid opener cable from fuel filler lid lock assembly. Refer to 

DLK-294, "FUEL FILLER LID

LOCK : Removal and Installation"

.

8.

Disengage each harness protector (1), and then remove fuel
filler lid opener cable (2).

9.

Remove fuel filler lid opener cable fixing clips, and then remove fuel filler lid opener cable.

INSTALLATION 

Note the following item, and install in the reverse order of removal.

CAUTION:

After installation, check fuel filler lid assembly open/close, lock/unlock operation.

FUEL FILLER LID LOCK

Clearance

Evenness

Fuel filler lid – Body side outer

2.0 – 4.0 (0.079 – 0.157)

(-1.0) – (+1.0) [(-0.039) – (+0.039)]

JMKIA5901ZZ

JMKIA5720ZZ

Revision: 2013 October

2014 JUKE

DLK-294

< REMOVAL AND INSTALLATION >

[WITHOUT INTELLIGENT KEY SYSTEM]

FUEL FILLER LID OPENER

FUEL FILLER LID LOCK : Removal and Installation

INFOID:0000000009754230

REMOVAL

1.

Fully open fuel filler lid.

2.

Remove luggage side lower finisher (RH). Refer to 

INT-35, "LUGGAGE SIDE LOWER FINISHER :

Removal and Installation"

.

3.

Rotate and disengage fuel filler lid lock assembly, and then
remove fuel filler lid lock assembly.
NOTE:
Operation is performed easily when rotating fuel filler lid lock
from passenger room side.

4.

Disengage fuel filler lid opener cable (1). Remove fuel filler lid
opener cable while pressing stopper pin (2).

INSTALLATION 

Note the following item, and install in the reverse order of removal.

CAUTION:

After installation, check fuel filler lid assembly open/close, lock/unlock operation.

JMKIA5718ZZ

JMKIA5719ZZ

Revision: 2013 October

2014 JUKE

DOOR SWITCH

DLK-295

< REMOVAL AND INSTALLATION >

[WITHOUT INTELLIGENT KEY SYSTEM]

C

D

E

F

G

H

I

J

L

M

A

B

DLK

N

O

P

DOOR SWITCH

Exploded View

INFOID:0000000009754231

Removal and Installation

INFOID:0000000009754232

REMOVAL

Remove the TORX bolt (A), and then remove door switch (1).

INSTALLATION

Install in the reverse order of removal.

1.

Door switch

2.

TORX bolt

JMKIA2569GB

JMKIA2173ZZ

Revision: 2013 October

2014 JUKE

DLK-296

< REMOVAL AND INSTALLATION >

[WITHOUT INTELLIGENT KEY SYSTEM]

REMOTE KEYLESS ENTRY RECEIVER

REMOTE KEYLESS ENTRY RECEIVER

Removal and Installation

INFOID:0000000009754233

REMOVAL

1.

Remove the glove box assembly. Refer to 

IP-13, "Removal and Installation"

.

2.

Remove the remote keyless entry receiver (1) mounting bolt (A),
and then remove remote keyless entry receiver.

INSTALLATION

Install in the reverse order of removal.

JMKIA6084ZZ

Revision: 2013 October

2014 JUKE

 

 

 

 

 

 

 

Content      ..     64      65      66      67     ..