Nissan Juke (2014 year). Service Repair Manual - part 59

 

  Index      Manuals     Nissan Juke (2014 year) - Service and Repair Manual

 

Search            copyright infringement  

 

 

 

 

 

 

 

 

Content      ..     57      58      59      60     ..

 

 

Nissan Juke (2014 year). Service Repair Manual - part 59

 

 

FUEL FILLER LID OPENER

DLK-169

< REMOVAL AND INSTALLATION >

[WITH INTELLIGENT KEY SYSTEM]

C

D

E

F

G

H

I

J

L

M

A

B

DLK

N

O

P

FUEL FILLER LID OPENER

Exploded View

INFOID:0000000009754089

FUEL FILLER LID

FUEL FILLER LID : Removal and Installation

INFOID:0000000009754090

REMOVAL 

1.

Fully open fuel filler lid. 

2.

Remove fuel mounting pin (1).

3.

Remove mounting screws, and then remove fuel filler lid.

INSTALLATION 

Note the following items, and install in the reverse order of removal.

1.

Fuel filler lid opener cable

2.

Cable protector

3.

Fuel filler lid lock assembly

4.

Fuel filler lid assembly

5.

Spring

6.

Bumper rubber

: Clip

: Do not reuse

JMKIA5904ZZ

JMKIA5717ZZ

Revision: 2013 October

2014 JUKE

DLK-170

< REMOVAL AND INSTALLATION >

[WITH INTELLIGENT KEY SYSTEM]

FUEL FILLER LID OPENER

CAUTION:

• After installation, check fuel filler lid assembly open/close, lock/unlock operation.
• After installation, apply the touch-up paint (the body color) onto the head of the mounting screws.
NOTE:
• The following table shows the specifide values for checking nomal installation status.
• Fitting adjustment cannot be perfomed.

Unit: mm (in)

FUEL FILLER OPENER CABLE

FUEL FILLER OPENER CABLE : Removal and Installation

INFOID:0000000009754091

REMOVAL 

1.

Remove hood lock control cable assembly from instrument lower panel (LH). Refer to 

DLK-158, "HOOD

LOCK CONTROL CABLE : Removal and Installation"

.

2.

Remove fuel filler lid opener cable (2) from fuel filler lid opener
lever (1).

3.

Remove front kicking plate inner (LH) and rear kicking plate inner (LH and RH). Refer to 

INT-19, "KICK-

ING PLATE INNER : Removal and Installation"

.

4.

Remove dash side finisher (LH). Refer to 

INT-21, "DASH SIDE FINISHER : Removal and Installation"

.

5.

Remove center pillar lower garnish (LH). Refer to 

INT-22, "CENTER PILLAR LOWER GARNISH :

Removal and Installation"

.

6.

Remove luggage side lower finisher (RH). Refer to 

INT-35, "LUGGAGE SIDE LOWER FINISHER :

Removal and Installation"

.

7.

Remove fuel filler lid opener cable from fuel filler lid lock assembly. Refer to 

DLK-171, "FUEL FILLER LID

LOCK : Removal and Installation"

.

8.

Disengage each harness protector (1), and then remove fuel
filler lid opener cable (2).

9.

Remove fuel filler lid opener cable fixing clips, and then remove fuel filler lid opener cable.

INSTALLATION 

Note the following item, and install in the reverse order of removal.

CAUTION:

After installation, check fuel filler lid assembly open/close, lock/unlock operation.

FUEL FILLER LID LOCK

Clearance

Evenness

Fuel filler lid – Body side outer

2.0 – 4.0 (0.079 – 0.157)

(-1.0) – (+1.0) [(-0.039) – (+0.039)]

JMKIA5901ZZ

JMKIA5720ZZ

Revision: 2013 October

2014 JUKE

FUEL FILLER LID OPENER

DLK-171

< REMOVAL AND INSTALLATION >

[WITH INTELLIGENT KEY SYSTEM]

C

D

E

F

G

H

I

J

L

M

A

B

DLK

N

O

P

FUEL FILLER LID LOCK : Removal and Installation

INFOID:0000000009754092

REMOVAL

1.

Fully open fuel filler lid.

2.

Remove luggage side lower finisher (RH). Refer to 

INT-35, "LUGGAGE SIDE LOWER FINISHER :

Removal and Installation"

.

3.

Rotate and disengage fuel filler lid lock assembly, and then
remove fuel filler lid lock assembly.
NOTE:
Operation is performed easily when rotating fuel filler lid lock
from passenger room side.

4.

Disengage fuel filler lid opener cable (1). Remove fuel filler lid
opener cable while pressing stopper pin (2).

INSTALLATION 

Note the following item, and install in the reverse order of removal.

CAUTION:

After installation, check fuel filler lid assembly open/close, lock/unlock operation.

JMKIA5718ZZ

JMKIA5719ZZ

Revision: 2013 October

2014 JUKE

DLK-172

< REMOVAL AND INSTALLATION >

[WITH INTELLIGENT KEY SYSTEM]

DOOR SWITCH

DOOR SWITCH

Exploded View

INFOID:0000000009754093

Removal and Installation

INFOID:0000000009754094

REMOVAL

Remove the TORX bolt (A), and then remove door switch (1).

INSTALLATION

Install in the reverse order of removal.

1.

Door switch

2.

TORX bolt

JMKIA2569GB

JMKIA2173ZZ

Revision: 2013 October

2014 JUKE

INSIDE KEY ANTENNA

DLK-173

< REMOVAL AND INSTALLATION >

[WITH INTELLIGENT KEY SYSTEM]

C

D

E

F

G

H

I

J

L

M

A

B

DLK

N

O

P

INSIDE KEY ANTENNA

INSTRUMENT CENTER

INSTRUMENT CENTER : Removal and Installation

INFOID:0000000009754095

REMOVAL

1.

Remove the multi display unit. Refer to 

AV-183, "Removal and Installation"

.

2.

Remove the inside key antenna (instrument center) (1) mount-
ing clip (A), and then remove inside key antenna (instrument
center).

CAUTION:

Be careful not to drop mounting clip (A) into instrument
panel.

INSTALLATION

Install in the reverse order of removal.

CONSOLE

CONSOLE : Removal and Installation

INFOID:0000000009754096

REMOVAL

1.

Remove the center console assembly. Refer to 

IP-24, "Removal and Installation"

.

2.

Remove the inside key antenna (console) (1) mounting clip (A),
and then remove inside key antenna (console).

INSTALLATION

Install in the reverse order of removal.

LUGGAGE ROOM

JMKIA5573ZZ

JMKIA5575ZZ

Revision: 2013 October

2014 JUKE

DLK-174

< REMOVAL AND INSTALLATION >

[WITH INTELLIGENT KEY SYSTEM]

INSIDE KEY ANTENNA

LUGGAGE ROOM : Exploded View

INFOID:0000000009754097

LUGGAGE ROOM : Removal and Installation

INFOID:0000000009754098

REMOVAL

1.

Remove the luggage floor finisher. Refer to 

INT-33, "Exploded View"

.

2.

Remove the inside key antenna (luggage room) (1) mounting
clip RH (A).

3.

Disengage inside key antenna (luggage room) fixing clip using a
flat-bladed screwdriver (A), and then pull out forward the inside
key antenna (luggage room).

INSTALLATION

Install in the reverse order of removal.

CAUTION:

Visually check the clips for deformation and damage during installation.
Replace with new ones if necessary.

1.

Inside key antenna (luggage room)

2.

Clip

: Do not reuse

JMKIA5576ZZ

JMKIA5577ZZ

JMKIA5578ZZ

Revision: 2013 October

2014 JUKE

OUTSIDE KEY ANTENNA

DLK-175

< REMOVAL AND INSTALLATION >

[WITH INTELLIGENT KEY SYSTEM]

C

D

E

F

G

H

I

J

L

M

A

B

DLK

N

O

P

OUTSIDE KEY ANTENNA

DRIVER SIDE

DRIVER SIDE : Removal and Installation

INFOID:0000000009754099

REMOVAL

Remove the driver side outside handle. Refer to 

DLK-161, "OUTSIDE HANDLE : Removal and Installation"

.

INSTALLATION

Install in the reverse order of removal.

PASSENGER SIDE

PASSENGER SIDE : Removal and Installation

INFOID:0000000009754100

REMOVAL

Remove the passenger side outside handle. Refer to 

DLK-161, "OUTSIDE HANDLE : Removal and Installa-

tion"

.

INSTALLATION

Install in the reverse order of removal.

REAR BUMPER

REAR BUMPER : Removal and Installation

INFOID:0000000009754101

REMOVAL

1.

Remove the rear bumper fascia. Refer to 

EXT-20, "Removal and Installation"

.

2.

Remove the outside key antenna (rear bumper) (1) mounting
clip (A), then remove outside key antenna (rear bumper).

INSTALLATION

Install in the reverse order of removal.

JMKIA5580ZZ

Revision: 2013 October

2014 JUKE

DLK-176

< REMOVAL AND INSTALLATION >

[WITH INTELLIGENT KEY SYSTEM]

INTELLIGENT KEY WARNING BUZZER

INTELLIGENT KEY WARNING BUZZER

Removal and Installation

INFOID:0000000009754102

REMOVAL

1.

Remove the Intelligent Key warning buzzer (1) mounting bolt
(A), and then remove the Intelligent Key warning buzzer.

INSTALLATION

Install in the reverse order of removal.

JMKIA5571ZZ

Revision: 2013 October

2014 JUKE

REMOTE KEYLESS ENTRY RECEIVER

DLK-177

< REMOVAL AND INSTALLATION >

[WITH INTELLIGENT KEY SYSTEM]

C

D

E

F

G

H

I

J

L

M

A

B

DLK

N

O

P

REMOTE KEYLESS ENTRY RECEIVER

Removal and Installation

INFOID:0000000009754103

REMOVAL

1.

Remove the glove box assembly. Refer to 

IP-13, "Removal and Installation"

.

2.

Remove the remote keyless entry receiver (1) mounting bolt (A),
and then remove remote keyless entry receiver.

INSTALLATION

Install in the reverse order of removal.

JMKIA6084ZZ

Revision: 2013 October

2014 JUKE

DLK-178

< REMOVAL AND INSTALLATION >

[WITH INTELLIGENT KEY SYSTEM]

INTELLIGENT KEY BATTERY

INTELLIGENT KEY BATTERY

Removal and Installation

INFOID:0000000009754104

1.

Release the lock knob at the back of the Intelligent Key and remove the mechanical key.

2.

Insert a remover tool (A) wrapped with a cloth into the slit of the
corner and twist it to separate the upper part from the lower part.

CAUTION:

• Do not touch the circuit board or battery terminal.
• The key fob is water-resistant. However, if it does get wet,

immediately wipe it dry. 

3.

Replace the battery with new one.

4.

Align the tips of the upper and lower parts, and then push them
together until it is securely closed.

CAUTION:

• When replacing battery, keep dirt, grease, and other for-

eign materials off the electrode contact area.

• After replacing the battery, check that all Intelligent Key

functions work normally.

PIIB6221E

Battery replacement

:Coin-type lithium battery 
(CR2025)

PIIB6222E

Revision: 2013 October

2014 JUKE

PRECAUTIONS

DLK-179

< PRECAUTION >

[WITHOUT INTELLIGENT KEY SYSTEM]

C

D

E

F

G

H

I

J

L

M

A

B

DLK

N

O

P

PRECAUTION

PRECAUTIONS

Precaution for Supplemental Restraint System (SRS) "AIR BAG" and "SEAT BELT 
PRE-TENSIONER"

INFOID:0000000009754105

The Supplemental Restraint System such as “AIR BAG” and “SEAT BELT PRE-TENSIONER”, used along
with a front seat belt, helps to reduce the risk or severity of injury to the driver and front passenger for certain
types of collision. This system includes seat belt switch inputs and dual stage front air bag modules. The SRS
system uses the seat belt switches to determine the front air bag deployment, and may only deploy one front
air bag, depending on the severity of a collision and whether the front occupants are belted or unbelted.
Information necessary to service the system safely is included in the “SRS AIR BAG” and “SEAT BELT” of this
Service Manual.

WARNING:

Always observe the following items for preventing accidental activation.
• To avoid rendering the SRS inoperative, which could increase the risk of personal injury or death in

the event of a collision that would result in air bag inflation, all maintenance must be performed by
an authorized NISSAN/INFINITI dealer.

• Improper maintenance, including incorrect removal and installation of the SRS, can lead to personal

injury caused by unintentional activation of the system. For removal of Spiral Cable and Air Bag
Module, see “SRS AIR BAG”.

• Never use electrical test equipment on any circuit related to the SRS unless instructed to in this Ser-

vice Manual. SRS wiring harnesses can be identified by yellow and/or orange harnesses or harness
connectors.

PRECAUTIONS WHEN USING POWER TOOLS (AIR OR ELECTRIC) AND HAMMERS

WARNING:

Always observe the following items for preventing accidental activation.
• When working near the Air Bag Diagnosis Sensor Unit or other Air Bag System sensors with the

ignition ON or engine running, never use air or electric power tools or strike near the sensor(s) with
a hammer. Heavy vibration could activate the sensor(s) and deploy the air bag(s), possibly causing
serious injury.

• When using air or electric power tools or hammers, always switch the ignition OFF, disconnect the

battery, and wait at least 3 minutes before performing any service.

Precaution for Procedure without Cowl Top Cover

INFOID:0000000009754106

When performing the procedure after removing cowl top cover, cover
the lower end of windshield with urethane, etc to prevent damage to
windshield.

PIIB3706J

Revision: 2013 October

2014 JUKE

DLK-180

< PRECAUTION >

[WITHOUT INTELLIGENT KEY SYSTEM]

PRECAUTIONS

Precautions for Removing of Battery Terminal

INFOID:0000000010288672

•  When removing the 12V battery terminal, turn OFF the ignition

switch and wait at least 30 seconds.
NOTE:
ECU may be active for several tens of seconds after the ignition
switch is turned OFF. If the battery terminal is removed before ECU
stops, then a DTC detection error or ECU data corruption may
occur.

•  For vehicles with the 2-batteries, be sure to connect the main bat-

tery and the sub battery before turning ON the ignition switch.
NOTE:
If the ignition switch is turned ON with any one of the terminals of
main battery and sub battery disconnected, then DTC may be
detected.

•  After installing the 12V battery, always check "Self Diagnosis Result" of all ECUs and erase DTC.

NOTE:
The removal of 12V battery may cause a DTC detection error.

Work

INFOID:0000000009754107

• After removing and installing the opening/closing parts, be sure to carry out fitting adjustments to check their

operational.

• Check the lubrication level, damage, and wear of each part. If necessary, grease or replace it.

SEF289H

Revision: 2013 October

2014 JUKE

PREPARATION

DLK-181

< PREPARATION >

[WITHOUT INTELLIGENT KEY SYSTEM]

C

D

E

F

G

H

I

J

L

M

A

B

DLK

N

O

P

PREPARATION

PREPARATION

Special Service Tools

INFOID:0000000009754108

The actual shapes of Kent-Moore tools may differ from those of special service tools illustrated here.

Commercial Service Tools

INFOID:0000000009754109

Tool number
(Kent-Moore No.)
Tool name

Description

(J-39570)
Chassis ear

Locating the noise

(J-50397)
NISSAN Squeak and Rat-
tle Kit

Repairing the cause of noise

SIIA0993E

SIIA0994E

Tool name

Description

Engine ear

Locating the noise

Remover tool

Remove the clips, pawls, and metal clips

Power tool

SIIA0995E

PIIB7923J

PIIB1407E

Revision: 2013 October

2014 JUKE

DLK-182

< SYSTEM DESCRIPTION >

[WITHOUT INTELLIGENT KEY SYSTEM]

COMPONENT PARTS

SYSTEM DESCRIPTION

COMPONENT PARTS

Component Parts Location

INFOID:0000000009754110

Component Description

INFOID:0000000009754111

1.

IPDM E/R
Refer to 

PCS-37, "Component Parts 

Location"

2.

TCM
Refer to 

TM-150, "CVT CONTROL 

SYSTEM : Component Parts Loca-
tion"

3.

Combination meter

4.

Key switch

5.

BCM
Refer to 

BCS-93, "BODY CONTROL 

SYSTEM : Component Parts Loca-
tion"

6.

Power window main switch
(door lock/unlock switch)

7.

Front door switch (driver side)

8.

Front door lock assembly (driver 
side)

9.

Back door opener assembly

10. Back door opener switch

11.

Remote keyless entry receiver

A.

View with the glove box assembly re-
moved

JMKIA6160ZZ

Item

Function

Back door opener actuator

Opens the back door with the back door open signal from BCM.

Back door opener switch

Inputs back door opener switch operation signal to BCM.

BCM

Controls the door lock system.

Revision: 2013 October

2014 JUKE

COMPONENT PARTS

DLK-183

< SYSTEM DESCRIPTION >

[WITHOUT INTELLIGENT KEY SYSTEM]

C

D

E

F

G

H

I

J

L

M

A

B

DLK

N

O

P

Combination meter

• Performs operation method guide and warning with buzzer.
• Transmits vehicle seep signal to CAN communication line.

Door lock actuator

• Inputs locks/unlocks signal from BCM and locks/unlocks each door.
• Integrated in each door lock assembly.

Door lock and unlock switch

Transmits door lock/unlock operation to BCM.

Door switch

Detects door open/close condition.

IPDM E/R

Sounds horn via CAN communication between BCM.

Keyfob

Transmits button operation to remote keyless entry receiver.

Key switch

Key switch detects that ignition key is inserted into the ignition key cylinder, and 
then transmits the signal to BCM. 

Remote keyless entry receiver

Receives keyfob operation and transmits to BCM.

TCM

Transmits shift position signal to BCM via CAN communication line.

Item

Function

Revision: 2013 October

2014 JUKE

DLK-184

< SYSTEM DESCRIPTION >

[WITHOUT INTELLIGENT KEY SYSTEM]

POWER DOOR LOCK SYSTEM

POWER DOOR LOCK SYSTEM

System Diagram

INFOID:0000000009754112

System Description

INFOID:0000000009754113

DOOR LOCK FUNCTION

• The door lock and unlock switch (driver side) is build into power window main switch.
• Interlocked with the locking operation of door lock and unlock switch, door lock actuators of all doors are

locked.

• Interlocked with the unlocking operation of door lock and unlock switch, door lock actuators of all doors and

are unlocked.

Door Key Cylinder

• With the door key inserted in the door key cylinder on driver side, turning it to “LOCK”, will lock door lock

actuator of all doors.

• With the door key inserted in the door key cylinder on driver side, turning it to “UNLOCK” once unlocks the

driver side door lock actuator; turning it to “UNLOCK” again within 5 seconds after the first unlock operation
unlocks all of the other doors. (SELECTIVE UNLOCK OPERATION)

KEY REMINDER FUNCTION

When door lock and unlock switch are operated while key is inserted into key switch and any door is open,
door locks once but immediately unlocks. This operation prevents keyfob from being left in the vehicle.

AUTOMATIC DOOR LOCK/UNLOCK FUNCTION (LOCK OPERATION)

The interlock door lock function is the function that locks all doors linked with the vehicle speed or shift posi-
tion. It has 2 types as follows. 

Vehicle Speed Sensing Auto Door Lock

All doors are locked when the vehicle speed reaches 24 km/h (15 MPH) or more. 
BCM outputs the lock signal to all door lock actuators when it detects that the ignition switch is turned ON, all
doors are closed and the vehicle speed received from the combination meter via CAN communication
becomes 24 km/h (15 MPH) or more. 

P Range Interlock Door Lock*

All doors are locked when shifting the selector lever from the P position to any position other than P. 
BCM outputs the lock signal to all door lock actuators when it detects that the ignition switch is in the ON posi-
tion and the shift signal received from the TCM via CAN communication is shifted from the P position to any
position other than P. 

Setting change of Automatic Door Lock/Unlock Function

The lock operation setting of the automatic door lock/unlock function can be changed. 

 With CONSULT

The ON/OFF switching of the automatic door lock function and the type selection of the automatic door lock/
unlock function can be performed at the WORK SUPPORT setting of CONSULT. 

 Without CONSULT 

JMKIA6161GB

Revision: 2013 October

2014 JUKE

 

 

 

 

 

 

 

Content      ..     57      58      59      60     ..