Nissan Juke (2014 year). Service Repair Manual

PRECAUTIONS

DLK-9

< PRECAUTION >

[WITH INTELLIGENT KEY SYSTEM]

DLK

PRECAUTION

PRECAUTIONS

Precaution for Supplemental Restraint System (SRS) "AIR BAG" and "SEAT BELT
PRE-TENSIONER"

INFOID:0000000009753917

The Supplemental Restraint System such as “AIR BAG” and “SEAT BELT PRE-TENSIONER”, used along
with a front seat belt, helps to reduce the risk or severity of injury to the driver and front passenger for certain
types of collision. This system includes seat belt switch inputs and dual stage front air bag modules. The SRS
system uses the seat belt switches to determine the front air bag deployment, and may only deploy one front
air bag, depending on the severity of a collision and whether the front occupants are belted or unbelted.
Information necessary to service the system safely is included in the “SRS AIR BAG” and “SEAT BELT” of this
Service Manual.

WARNING:

Always observe the following items for preventing accidental activation.
• To avoid rendering the SRS inoperative, which could increase the risk of personal injury or death in

the event of a collision that would result in air bag inflation, all maintenance must be performed by
an authorized NISSAN/INFINITI dealer.

• Improper maintenance, including incorrect removal and installation of the SRS, can lead to personal

injury caused by unintentional activation of the system. For removal of Spiral Cable and Air Bag
Module, see “SRS AIR BAG”.

• Never use electrical test equipment on any circuit related to the SRS unless instructed to in this Ser-

vice Manual. SRS wiring harnesses can be identified by yellow and/or orange harnesses or harness
connectors.

PRECAUTIONS WHEN USING POWER TOOLS (AIR OR ELECTRIC) AND HAMMERS

WARNING:

Always observe the following items for preventing accidental activation.
• When working near the Air Bag Diagnosis Sensor Unit or other Air Bag System sensors with the

ignition ON or engine running, never use air or electric power tools or strike near the sensor(s) with
a hammer. Heavy vibration could activate the sensor(s) and deploy the air bag(s), possibly causing
serious injury.

• When using air or electric power tools or hammers, always switch the ignition OFF, disconnect the

battery, and wait at least 3 minutes before performing any service.

Precaution for Procedure without Cowl Top Cover

INFOID:0000000009753918

When performing the procedure after removing cowl top cover, cover
the lower end of windshield with urethane, etc to prevent damage to
windshield.

PIIB3706J

Revision: 2013 October

2014 JUKE

DLK-10

< PRECAUTION >

[WITH INTELLIGENT KEY SYSTEM]

PRECAUTIONS

Precautions for Removing of Battery Terminal

INFOID:0000000010288671

• When removing the 12V battery terminal, turn OFF the ignition

switch and wait at least 30 seconds.
NOTE:
ECU may be active for several tens of seconds after the ignition
switch is turned OFF. If the battery terminal is removed before ECU
stops, then a DTC detection error or ECU data corruption may
occur.

• For vehicles with the 2-batteries, be sure to connect the main bat-

tery and the sub battery before turning ON the ignition switch.
NOTE:
If the ignition switch is turned ON with any one of the terminals of
main battery and sub battery disconnected, then DTC may be
detected.

• After installing the 12V battery, always check "Self Diagnosis Result" of all ECUs and erase DTC.

NOTE:
The removal of 12V battery may cause a DTC detection error.

Work

INFOID:0000000009753919

• After removing and installing the opening/closing parts, be sure to carry out fitting adjustments to check their

operational.

• Check the lubrication level, damage, and wear of each part. If necessary, grease or replace it.

SEF289H

Revision: 2013 October

2014 JUKE

PREPARATION

DLK-11

< PREPARATION >

[WITH INTELLIGENT KEY SYSTEM]

DLK

PREPARATION

Special Service Tools

INFOID:0000000009753920

The actual shapes of Kent-Moore tools may differ from those of special service tools illustrated here.

Commercial Service Tools

INFOID:0000000009753921

Tool number

(Kent-Moore No.)

Tool name

Description

(J-39570)
Chassis ear

Locates the noise

(J-50397)
NISSAN Squeak and Rat-
tle Kit

Repairs the cause of noise

SIIA0993E

SIIA0994E

Tool name

Description

Engine ear

Locates the noise

Remover tool

Removes the clips, pawls, and metal clips

Power tool

SIIA0995E

JMKIA3050ZZ

PIIB1407E

Revision: 2013 October

2014 JUKE

COMPONENT PARTS

DLK-13

< SYSTEM DESCRIPTION >

[WITH INTELLIGENT KEY SYSTEM]

DLK

Component Description

INFOID:0000000009753923

Intelligent Key warning buzzer

Remote keyless entry receiver

Inside key antenna (instrument cen-
ter)

TCM
Refer to

TM-150, "CVT CONTROL

SYSTEM : Component Parts Location"

Push-button ignition switch

Combination meter

BCM
Refer to

BCS-6, "BODY CONTROL

SYSTEM : Component Parts Location"

Power window main switch

Outside key antenna (driver side)

10. Front door switch (driver side)

11.

Front door lock assembly (driver side) 12. Front door request switch (driver side)

13. Inside key antenna (console)

14. Inside key antenna (luggage room)

15. Back door request switch

16. Back door lock assembly

17. Outside antenna (rear bumper)

18. Front door request switch (passenger

side)

19. Outside key antenna (passenger side) 20. IPDM E/R

Refer to

PCS-5, "Component Parts

Location"

View with front bumper removed

View with instrument panel assembly
removed

View with multi display unit removed

View with center console assembly re-
moved

View with luggage room finisher re-
moved

View with rear bumper removed

Item

Function

BCM

Controls the door lock system.

Back door opener actuator

Opens the back door with the back door open signal from BCM.

Back door opener switch

Inputs back door opener switch operation signal to BCM.

Combination meter

• Displays each operation method guide and warning for system malfunction.
• Performs operation method guide and warning with buzzer.
• Transmits vehicle seep signal to CAN communication line.

Door lock actuator

• Inputs locks/unlocks signal from BCM and locks/unlocks each door.
• Integrated in each door lock assembly.

Door lock and unlock switch

• Transmits door lock/unlock operation to BCM.
• Integrated in the power window main switch and front power window switch (passenger side).

Door request switch

• Transmits door lock/unlock operation to BCM.
• Integrated in the outside handle (driver side, passenger side and back door).

Door switch

Detects door open/close condition.

Inside key antenna

• Detects whether Intelligent Key is inside the vehicle.
• Installed in the instrument center and luggage room.

Intelligent Key

The following functions are available when having and carrying electronic ID.
• Door lock/unlock
• Engine start
• Remote control entry function is available when operating on button.

Intelligent Key warning buzzer

Warns for an inappropriate operation.

IPDM E/R

Sounds horn via CAN communication between BCM.

Outside key antenna

• Detects whether Intelligent Key is outside the vehicle.
• Integrated in the outside handle (driver side, passenger side and back door).

Push-button ignition switch

• BCM transmits the change in the power supply position with the push-button ignition switch to

IPDM E/R via CAN communication line. IPDM E/R transmits the power supply position status
via CAN communication line to BCM.

• Immobilizer antenna amp checks Intelligent Key transponder.

Remote keyless entry receiver

Receives Intelligent Key operation and transmits to BCM.

TCM

Transmits shift position signal to BCM via CAN communication line

Revision: 2013 October

2014 JUKE

DLK-14

< SYSTEM DESCRIPTION >

[WITH INTELLIGENT KEY SYSTEM]

SYSTEM (POWER DOOR LOCK SYSTEM)

SYSTEM (POWER DOOR LOCK SYSTEM)

System Diagram

INFOID:0000000009753924

System Description

INFOID:0000000009753925

DOOR LOCK FUNCTION

Door Lock and Unlock Switch

• The door lock and unlock switch (driver side) is build into power window main switch.
• Interlocked with the locking operation of door lock and unlock switch, door lock actuators of all doors are

locked.

• Interlocked with the unlocking operation of door lock and unlock switch, door lock actuators of all doors actu-

ator are unlocked.

Door Key Cylinder Switch

• With the mechanical key inserted in the door key cylinder on driver side, turning it to lock position, locks door

lock actuator of all doors.

• With the mechanical key inserted in the door key cylinder on driver side, turning it to unlock position once

unlocks the driver side door, turning it to unlock position again within 5 seconds after the first unlock opera-
tion unlocks all of the other doors actuator. (SELECTIVE UNLOCK OPERATION)

Selective unlock operation mode can be changed using CONSULT.
Refer to

DLK-29, "DOOR LOCK : CONSULT Function (BCM - DOOR LOCK)"

IGNITION POSITION WARNING FUNCTION

When door lock and unlock switch are operated while driver side door is open and ignition position is ACC or
ON, door locks once but immediately unlocks.

INTERIOR ROOM LAMP CONTROL FUNCTION

Interior room lamp is controlled according to door lock /unlock state, refer to

INL-6, "INTERIOR ROOM LAMP

CONTROL SYSTEM : System Description"

AUTOMATIC DOOR LOCK/UNLOCK FUNCTION (LOCK OPERATION)

The interlock door lock function is the function that locks all doors linked with the vehicle speed or shift posi-
tion. It has 2 types as per the following items.

Vehicle Speed Sensing Auto Door Lock

All doors are locked when the vehicle speed reaches 24 km/h (15 MPH) or more.
BCM outputs the lock signal to all door lock actuators when it detects that the ignition switch is turned ON, all
doors are closed and the vehicle speed received from the combination meter via CAN communication
becomes 24 km/h (15 MPH) or more.

P Range Interlock Door Lock*

All doors are locked when shifting the selector lever from the P position to any position other than P.
BCM outputs the lock signal to all door lock actuators when it detects that the ignition switch is in the ON posi-
tion and the shift signal received from the TCM via CAN communication is shifted from the P position to any
position other than P.

JMKIA6117GB

Revision: 2013 October

2014 JUKE

SYSTEM (POWER DOOR LOCK SYSTEM)

DLK-15

< SYSTEM DESCRIPTION >

[WITH INTELLIGENT KEY SYSTEM]

DLK

Setting change of Automatic Door Lock/Unlock Function

The lock operation setting of the automatic door lock/unlock function can be changed.
NOTE:
P range interlock door lock can be selected for M/T models, but automatic door lock/unlock function does not
operate.

With CONSULT

The ON/OFF switching of the automatic door lock function and the type selection of the automatic door lock/
unlock function can be performed at the WORK SUPPORT setting of CONSULT.

Without CONSULT

The automatic door lock function ON/OFF can be switched by performing the following operation.

Close all doors (door switch OFF)

Ignition switch: OFF

→

Press and hold the door lock and unlock switch for 5 seconds or more in the lock direction within 20 sec-
onds after turning the ignition switch ON.

The switching complete when the hazard lamp blinks.

*: This function does not operate on M/T models.

AUTOMATIC DOOR LOCK/UNLOCK FUNCTION (UNLOCK OPERATION)

The automatic door lock/unlock function is the function that unlocks all doors linked with the key position or
shift position. It has 2 types as per the following items.

IGN OFF Interlock Door Unlock*

All doors are unlocked when the power supply position is changed from ON to OFF.
BCM outputs the unlock signal to all door lock actuators when it detects that the power supply position is
changed from ignition switch ON to OFF.

P Range Interlock Door Unlock*

All doors are unlocked when shifting the selector lever from any position other than the P to P position.
BCM outputs the unlock signal to all door lock actuators when it detects that the ignition switch is in the ON
position and the shift signal received from TCM via CAN communication is shifted from any position other than
the P to P position.

Setting change of Automatic Door Lock/Unlock Function

The unlock operation setting of the automatic door lock/unlock function can be changed.
NOTE:
P range interlock door lock can be selected for M/T models, but automatic door lock/unlock function does not
operate.

With CONSULT

The ON/OFF switching of the automatic door lock/unlock function and the type selection of the automatic door
lock/unlock function can be performed at the WORK SUPPORT setting of CONSULT. Refer to

DLK-29,

"DOOR LOCK : CONSULT Function (BCM - DOOR LOCK)"

Without CONSULT

The automatic door lock/unlock function ON/OFF can be switched by performing the following operation.
1.

Close all doors below (door switch OFF)

Ignition switch: OFF

→

Press and hold the door lock and unlock switch for 5 seconds or more in the unlock direction within 20
seconds after turning the power supply position ON.

The switching is complete when the hazard lamp blinks.

: This function is set to ON before delivery.

: This function does not operate on M/T models.

OFF

→

: 2 blinks

→

OFF

: 1 blink

OFF

→

: 2 blinks

→

OFF

: 1 blink

Revision: 2013 October

2014 JUKE

DLK-16

< SYSTEM DESCRIPTION >

[WITH INTELLIGENT KEY SYSTEM]

SYSTEM (INTELLIGENT KEY SYSTEM)

SYSTEM (INTELLIGENT KEY SYSTEM)

INTELLIGENT KEY SYSTEM

INTELLIGENT KEY SYSTEM : System Diagram

INFOID:0000000009753926

INTELLIGENT KEY SYSTEM : System Description

INFOID:0000000009753927

• The Intelligent Key system is a system that makes it possible to lock and unlock the door locks (door lock/

unlock function) by carrying the Intelligent Key, which operates based on the results of electronic ID verifica-
tion using two-way communication between the Intelligent Key and the vehicle (BCM).

CAUTION:

The driver should always carry the Intelligent Key

• The settings for each function can be changed with CONSULT.
• If an Intelligent Key is lost, a new Intelligent Key can be registered. A maximum of 4 Intelligent Keys can be

registered.

• It is possible to perform a diagnosis on the system and register an Intelligent Key with CONSULT.

JMKIA6118GB

Function

Description

Refer

Door lock

Lock/unlock can be performed by pressing the request switch

DLK-17

Remote keyless entry

Lock/unlock can be performed by pressing the remote controller button of the In-
telligent Key

DLK-21

Key reminder

The key reminder buzzer sounds a warning if the door is locked with the key left
inside the vehicle

DLK-23

Revision: 2013 October

2014 JUKE

SYSTEM (INTELLIGENT KEY SYSTEM)

DLK-17

< SYSTEM DESCRIPTION >

[WITH INTELLIGENT KEY SYSTEM]

DLK

DOOR LOCK FUNCTION

DOOR LOCK FUNCTION : System Diagram

INFOID:0000000009753928

DOOR LOCK FUNCTION : System Description

INFOID:0000000009753929

When pressing the door request switch, it is possible to lock and unlock the door by carrying the Intelligent
Key.

OPERATION DESCRIPTION

• When the BCM detects that each door request switch is pressed, it activates the outside key antenna and

inside key antenna corresponding to the pressed door request switch and transmits the request signal to the
Intelligent Key. And then, check that the Intelligent Key is near the door.

• If the Intelligent Key is within the outside key antenna detection area, it receives the request signal and

transmits the key ID signal to the BCM via remote keyless entry receiver.

• BCM receives the key ID signal and compares it with the registered key ID.
• BCM transmits door lock/unlock signal and operates each door lock actuator. At the same time, BCM blinks

hazard warning lamp (lock: 2 times, unlock: 1 time) and sounds Intelligent Key buzzer (lock: 2 times, unlock:
1 time) as a reminder.

OPERATION CONDITION

If the following conditions are satisfied, door lock/unlock operation is performed if the door request switch is
operated.

Warning

If an action that does not meet the operating condition of the Intelligent Key sys-
tem is taken, the buzzer sounds to inform the driver

DLK-24

Engine start

The engine can be turned on while carrying the Intelligent Key

SEC-12

Interior room lamp control

Interior room lamp is controlled according to door lock/unlock state

INL-6

Panic alarm

When Intelligent Key panic alarm button is pressed, horn sounds

SEC-18

Function

Description

Refer

JMKIA6137GB

Revision: 2013 October

2014 JUKE

DLK-18

< SYSTEM DESCRIPTION >

[WITH INTELLIGENT KEY SYSTEM]

SYSTEM (INTELLIGENT KEY SYSTEM)

*: Even with a registered Intelligent Key remaining inside the vehicle, door locks can be unlocked from outside of the vehicle with a spare
Intelligent Key as long as key IDs are different.

OUTSIDE KEY ANTENNA DETECTION AREA

The outside key antenna detection area of door lock/unlock function
is in the range of approximately 80 cm (31.50 in) surrounding the
driver, passenger door handles (1) and back door handle (2). How-
ever, this operating range depends on the ambient conditions.

SELECTIVE UNLOCK FUNCTION

Lock Operation

When an LOCK signal is sent from door request switch (driver side, passenger side or back door), all doors
are locked.

Unlock Operation

• When an UNLOCK signal from front door request switch (driver side) is transmitted, driver side door

unlocks. When another UNLOCK signal is transmitted within 60 seconds, all door unlocks.

• When an UNLOCK signal from front door request switch (passenger side) is transmitted, passenger side

door unlocks. When another UNLOCK signal is transmitted within 60 seconds, all door unlocks.

• When an UNLOCK signal from back door request switch is transmitted, back door unlocks. When another

UNLOCK signal is transmitted within 60 seconds, all door unlocks.

How to Change Selective Unlock Operation Mode

Selective unlock operation mode can be changed using CONSULT.
Refer to

DLK-31, "INTELLIGENT KEY : CONSULT Function (BCM - INTELLIGENT KEY)"

HAZARD AND BUZZER REMINDER FUNCTION

During lock, unlock, operation by each request switch, the hazard warning lamps and Intelligent Key warning
buzzer will blink or honk as a reminder.
When doors are locked, unlocked by each request switch, BCM honks Intelligent Key warning buzzer as a
reminder and blinks.

Operating Function of Hazard and Buzzer Reminder

Hazard and buzzer reminder does not operate if ignition switch ON position.

How to Change Hazard and Buzzer Reminder Operation Mode

Hazard and buzzer reminder operation mode can be changed using CONSULT.
Refer to

DLK-31, "INTELLIGENT KEY : CONSULT Function (BCM - INTELLIGENT KEY)"

AUTO DOOR LOCK FUNCTION

Each door request switch operation

Operation condition

Lock

• All doors are closed
• Panic alarm is not activated
• P position warning is not activated
• Intelligent Key is outside the vehicle
• Intelligent Key is within outside key antenna detection area

Unlock

• All doors are closed
• Panic alarm is not activated
• Intelligent Key is outside the vehicle
• Intelligent Key is within outside key antenna detection area *

JMKIA5569ZZ

Operation

Hazard warning lamp blinks

Intelligent Key warning buzzer honk

Unlock

Once

Lock

Twice

Revision: 2013 October

2014 JUKE

SYSTEM (INTELLIGENT KEY SYSTEM)

DLK-19

< SYSTEM DESCRIPTION >

[WITH INTELLIGENT KEY SYSTEM]

DLK

After door is unlocked by door request switch operation and if 60 seconds or more passes without performing
the following operation, all doors are automatically locked. However, operation check function does not acti-
vate.

How To Change Auto Door Lock Operation Mode

Auto door lock operation mode can be changed using CONSULT.
Refer to

DLK-31, "INTELLIGENT KEY : CONSULT Function (BCM - INTELLIGENT KEY)"

LIST OF OPERATION RELATED PARTS

Parts marked with

are the parts related to operation.

BACK DOOR OPEN FUNCTION

BACK DOOR OPEN FUNCTION : System Diagram

INFOID:0000000009753930

BACK DOOR OPEN FUNCTION : System Description

INFOID:0000000009753931

While back door open in the permitted state, back door opens when back door opener switch is pressed after
back door opener request switch is operated.

BACK DOOR OPEN

Operating condition

• Door switch is ON (door is open)
• Door is locked
• Push switch is pressed

Door lock function

tel

lig

t Ke

s en

try rec

ive

or swi

tch

Doo

r re

t s

itc

or l

k ac

ten

Out

e ke

y ant

Int

llig

t Ke

rni

zze

CAN co

tem

BCM

Hazard warning

lamp

-bu

tto

n i

iti

swi

tch

met

Door lock/unlock function

Hazard and buzzer reminder function

Selective unlock function

Auto door lock function

JMKIA6136GB

Revision: 2013 October

2014 JUKE

DLK-20

< SYSTEM DESCRIPTION >

[WITH INTELLIGENT KEY SYSTEM]

SYSTEM (INTELLIGENT KEY SYSTEM)

• When the BCM detects that back door opener switch is pressed, it starts the outside key antenna (rear

bumper) and inside key antenna and transmits the request signal to the Intelligent Key. Then, check that the
Intelligent Key is near the back door.

• If the Intelligent Key is within the outside key antenna detection area, it receives the request signal and

transmits the key ID signal to the BCM via remote keyless entry receiver.

• BCM receives the key ID signal and compares it with the registered key ID.
• BCM opens back door, simultaneously unlocks all doors.
NOTE:
In selective unlock mode, only back door opens. All doors do not unlock.

OPERATION CONDITION

If the following conditions are satisfied, the back door can be opened.

OUTSIDE KEY ANTENNA DETECTION AREA

The outside key antenna detection area of back door open function
is in the range of approximately 80 cm (31.50 in) surrounding the
back door opener switch (1). However, this operating range depends
on the ambient conditions.

LIST OF OPERATION RELATED PARTS

Parts marked with

are the parts related to operation.

REMOTE KEYLESS ENTRY FUNCTION

Back door open function

Operation condition

Back door open operation

• Vehicle speed is less than 5 km/h (3 MPH)
• 3 seconds or more after BCM outputs all doors lock signal
• Intelligent Key is outside of vehicle
• Intelligent Key is within outside key antenna detection area

JMKIA5804ZZ

Door lock function

lli

nt Key

te ke

s ent

ry rec

r op

tua

or l

tua

y a

ten

nna

CAN co

ati

tem

BCM

r op

swit

ati

Back door open function

Revision: 2013 October

2014 JUKE

SYSTEM (INTELLIGENT KEY SYSTEM)

DLK-21

< SYSTEM DESCRIPTION >

[WITH INTELLIGENT KEY SYSTEM]

DLK

REMOTE KEYLESS ENTRY FUNCTION : System Diagram

INFOID:0000000009753932

REMOTE KEYLESS ENTRY FUNCTION : System Description

INFOID:0000000009753933

The Intelligent Key has the same functions as the remote control entry system. Therefore, it can be used in the
same manner as the remote controller by operating the door lock/unlock button.

OPERATION

Remote keyless entry system controls operation of the following items.
• Door lock/unlock
• Selective unlock function
• Hazard reminder function
• Auto door lock

OPERATION AREA

To check that the Intelligent Key works normally, use within 1 m (3 ft) range of each doors, however the opera-
ble range may differ according to surroundings.

DOOR LOCK/UNLOCK FUNCTION

• When door lock/unlock button of the Intelligent Key is pressed, lock signal or unlock signal transmitted from

Intelligent Key to BCM via remote keyless entry receiver.

• BCM receives the signal and compares it with the registered key ID to the vehicle.
• When BCM receives the door lock/unlock signal, it operates all door lock actuators and the hazard lamp

(lock: 2 times, unlock: 1 time) and horn chirp signal to IPDM E/R at the same time as a reminder.

• IPDM E/R honks horn (lock: 1 times) as a reminder

OPERATION CONDITION

If the following condition are satisfied, remote keyless entry operation is performed when the Intelligent Key is
operated.

SELECTIVE UNLOCK FUNCTION

• When an LOCK signal is transmitted from Intelligent Key, all doors are locked.
• When an UNLOCK signal is transmitted from Intelligent Key once, driver side door is unlocked.
• Then, if an UNLOCK signal is transmitted from Intelligent Key again within 60 seconds, all other doors are

unlocked.

How To Change Selective Unlock Operation Mode

Selective unlock operation mode can be changed using CONSULT.

JMKIA6159GB

Remote controller operation

Operation condition

Lock

• Panic alarm is not activated
• P position warning is not activated

Unlock

Panic alarm is not activated

Revision: 2013 October

2014 JUKE

DLK-22

< SYSTEM DESCRIPTION >

[WITH INTELLIGENT KEY SYSTEM]

SYSTEM (INTELLIGENT KEY SYSTEM)

Refer to

DLK-29, "DOOR LOCK : CONSULT Function (BCM - DOOR LOCK)"

HAZARD AND HORN REMINDER FUNCTION

When doors are locked or unlocked by Intelligent Key, BCM blinks hazard warning lamps as a reminder and
transmits horn chirp signal to IPDM E/R. IPDM E/R sounds horn as a reminder.
The hazard and horn reminder has a horn chirp mode (C mode) and a non-horn chirp mode (S mode).

Operating Function of Hazard and Horn Reminder

Hazard and horn reminder does not operate if ignition switch ON position.
How to change hazard and horn reminder mode

With CONSULT

Refer to

DLK-31, "INTELLIGENT KEY : CONSULT Function (BCM - INTELLIGENT KEY)"

Without CONSULT

When LOCK and UNLOCK signals are sent from the Intelligent Key for more than 2 seconds at the same time,
the hazard and horn reminder mode is changed and hazard warning lamp blinks and horn sounds as per the
following items:

AUTO DOOR LOCK FUNCTION

After door is unlocked by Intelligent Key button operation and if 60 seconds or more passes without performing
the following operation, all doors are locked. However, operation check function does not activate.

How To Change Auto Door Lock Operation Mode

Auto door lock operation mode can be changed using CONSULT.
Refer to

DLK-31, "INTELLIGENT KEY : CONSULT Function (BCM - INTELLIGENT KEY)"

LIST OF OPERATION RELATED PARTS

Parts marked with

are the parts related to operation.

C mode

S mode

Intelligent Key operation

Lock

Unlock

Back door

open

Lock

Unlock

Back door

open

Hazard warning lamp blinks

Twice

Once

—

Twice

—

Horn sound

Once

—

JMKIA6362GB

Operating condition

• Door switch is ON (door is open)
• Door is locked
• Push switch is pressed

Revision: 2013 October

2014 JUKE

SYSTEM (INTELLIGENT KEY SYSTEM)

DLK-23

< SYSTEM DESCRIPTION >

[WITH INTELLIGENT KEY SYSTEM]

DLK

KEY REMINDER FUNCTION

KEY REMINDER FUNCTION : System Diagram

INFOID:0000000009753934

KEY REMINDER FUNCTION : System Description

INFOID:0000000009753935

Key reminder is the function that prevents the key from being left in the vehicle.
Key reminder has the following 3 functions.

Remote keyless entry functions

Int

llig

t Ke

Doo

r swi

tch

or l

tua

-bu

tto

n i

iti

swi

tch

Inte

llige

t Ke

y wa

rni

CAN c

ica

n sy

BCM

ion

Hazard warning lamp

Horn

DM E/

Door lock/unlock function

Hazard and horn reminder function

Selective unlock function

Auto door lock function

JMKIA5390GB

Key remainder func-

tion

Operation condition

Operation

Driver side door
closed*

Right after driver side door is closed under the following conditions
• Intelligent Key is inside the vehicle
• Driver side door is opened
• Driver side door is in unlock state

All doors unlock

Door is open to closed

Right after all doors are closed under the following conditions
• Intelligent Key is inside the vehicle
• Any door is opened
• All doors are locked.

• All doors unlock
• Honk Intelligent Key warn-

ing buzzer

Back door is closed

Right after back door is closed under the following conditions
• Intelligent Key is inside the vehicle
• All doors (except back door) are closed
• All doors (except back door) are locked

• All doors unlock
• Back door can open with

back door opener switch

• Honk Intelligent Key warn-

ing buzzer

Revision: 2013 October

2014 JUKE

DLK-24

< SYSTEM DESCRIPTION >

[WITH INTELLIGENT KEY SYSTEM]

SYSTEM (INTELLIGENT KEY SYSTEM)

*:If the door closing impact shocks the door lock knob, or contacts against baggage with the door lock knob might activate the door locks
accidentally but unlock operation is perform in these cases.

CAUTION:

• The above function operates when the Intelligent Key is inside the vehicle. However, there may be

times when the Intelligent Key cannot be detected, and this function does not operate when the Intel-
ligent Key is on the instrument panel, rear parcel shelf, or in the glove box. Also, this system some-
times does not operate if the Intelligent Key is in the door pocket for the open door.

WARNING FUNCTION

WARNING FUNCTION : System Description

INFOID:0000000009753936

OPERATION DESCRIPTION

The warning function are as per the following items and are given to the user as warning information and
warnings using combinations of Intelligent Key warning buzzer, combination meter buzzer, KEY warning lamp,
shift P warning lamp and engine start operation indicator lamp.
• Intelligent Key system malfunction
• OFF position warning
• P position warning
• ACC warning
• Take away warning
• Door lock operation warning
• Engine start information
• Intelligent Key low battery warning
• Key ID warning

OPERATION CONDITION

Operation condition of warning and information is as per the following table.

Warning/Information functions

Operation procedure

Intelligent Key system malfunction

A malfunction is detected on BCM and key warning lamp turns ON

OFF position warning

For internal

When condition A, B or condition C is satisfied
• Condition A
- Ignition switch: ACC position
- Door switch (driver side): ON (Door is open)
• Condition B
- Turn ignition switch from ON to OFF while door is open
• Condition C
- Intelligent Key backside is contacted to ignition switch while brake pedal is de-

pressed and ignition switch is LOCK or OFF (When the Intelligent Key battery
is discharged)

- Door switch (driver side): ON (Door is open)

For external*

OFF position warning (For internal) is in active mode, driver side door is closed
NOTE:
OFF position warning (for external) operates only when driver door is closed af-
ter each of P position warning, ACC warning, and OFF position warning (inter-
nal) sounds.

P position warning*

For internal

• Shift position: Except P position
• Engine is running to stopped (Ignition switch is ON to OFF)

For external

• P position warning (For internal) operates
• Door switch: ON to OFF (Door is open to close)
• Intelligent Key cannot be detected inside the vehicle

ACC warning*

• After P position warning operates, or when ignition switch is turned ON imme-

diately after P position warning operates

• Ignition switch: ACC position

Revision: 2013 October

2014 JUKE

Nissan Juke (2014 year). Service Repair Manual - part 49