Nissan Juke (2012 year). Service Repair Manual - part 246

 

  Index      Manuals     Nissan Juke (2012 year) - Service and Repair Manual

 

Search            copyright infringement  

 

 

 

 

 

 

 

 

Content      ..     244      245      246      247     ..

 

 

Nissan Juke (2012 year). Service Repair Manual - part 246

 

 

WW-50

< REMOVAL AND INSTALLATION >

WASHER LEVEL SWITCH

WASHER LEVEL SWITCH

Removal and Installation

INFOID:0000000007579584

The washer level switch must be replaced together with the washer tank as an assembly. Refer to 

WW-47,

"Removal and Installation"

.

Revision: 2011 October

2012 JUKE

FRONT WASHER NOZZLE AND TUBE

WW-51

< REMOVAL AND INSTALLATION >

C

D

E

F

G

H

I

J

K

M

A

B

WW

N

O

P

FRONT WASHER NOZZLE AND TUBE

Exploded View

INFOID:0000000007579585

Hydraulic Layout

INFOID:0000000007579586

Removal and Installation

INFOID:0000000007579587

REMOVAL

1.

Remove cowl top cover. Refer to 

EXT-20, "Removal and Installation"

.

2.

Disconnect front washer tube from front washer nozzle.

1.

Front washer nozzle LH

2.

Front washer nozzle RH

3.

Cowl top cover

4.

Front washer tube (tank side)

5.

Front washer tube RH

6.

Front washer tube LH

: Vehicle front

JMLIA1385ZZ

1.

Front washer nozzle

2.

Check valve

3.

Front washer tube

4.

Washer tank

: Clip

JMLIA1161ZZ

Revision: 2011 October

2012 JUKE

WW-52

< REMOVAL AND INSTALLATION >

FRONT WASHER NOZZLE AND TUBE

3.

While pressing pawl (A) on the cowl top cover front side of front
washer nozzle (1), remove front washer nozzle from cowl top
cover.

INSTALLATION

Note the following item, and then install in the reverse order of removal.

CAUTION:

The spray positions differ, check that left and right nozzles are installed correctly.

Inspection and Adjustment

INFOID:0000000007579588

INSPECTION

Check valve Inspection

Check that air can pass through the hose by blowing forward (toward
the nozzle (1)), and check that air cannot pass through by sucking.

ADJUSTMENT

Washer Nozzle Spray Position Adjustment

Adjust spray positions to match the positions shown in the figure.

JPLIA0871ZZ

JMLIA1326ZZ

1.

Black printed frame line

: Spray area

: Target spray position

JMLIA1497ZZ

Revision: 2011 October

2012 JUKE

FRONT WASHER NOZZLE AND TUBE

WW-53

< REMOVAL AND INSTALLATION >

C

D

E

F

G

H

I

J

K

M

A

B

WW

N

O

P

Unit: mm (in)

Insert a needle or similar object (A) into the spray opening (1) and
move up/down and left/right to adjust the spray position.
NOTE:
If wax or dust gets into the nozzle, remove wax or dust with a needle
or small pin.

Spray position

H

L

X

Y

S

A

244 (9.61)

350 (13.78)

80 (3.15)

 238 (9.37)

 78 (3.07)

B

284 (11.18)

 93 (3.66)

80 (3.15)

 257 (10.12)

 89 (3.50)

C

258 (10.16)

 70.5 (2.78)

80 (3.15)

 255 (10.04)

 82 (3.23)

D

309 (12.17)

 234 (9.21)

80 (3.15)

 312 (12.28)

 95 (3.74)

E

235 (9.25)

413 (16.26)

80 (3.15)

295 (11.61)

90 (3.54)

JPLIA0873ZZ

Revision: 2011 October

2012 JUKE

WW-54

< REMOVAL AND INSTALLATION >

FRONT WIPER ARM

FRONT WIPER ARM

Exploded View

INFOID:0000000007579589

Removal and Installation

INFOID:0000000007579590

REMOVAL

1.

Operate front wiper to move it to the auto stop position.

2.

Open the hood.

3.

Disengage front wiper arm cap (1) fixing pawls with a remover
tool (A), and then remove front wiper arm cap from the wiper
arm (2).

4.

Remove front wiper arm mounting nuts.

5.

Raise front wiper arm, and then remove front wiper arm from the vehicle.

INSTALLATION

1.

Front wiper arm cap

2.

Front wiper arm LH

3.

Front wiper blade LH

4.

Front wiper arm RH

5.

Front wiper blade RH

6.

Front wiper drive assembly

: Pawl

: N·m (kg-m, in-lb)

: N·m (kg-m, ft-lb)

JMLIA1732GB

: Pawl

: Vehicle front

JMLIA1164ZZ

Revision: 2011 October

2012 JUKE

FRONT WIPER ARM

WW-55

< REMOVAL AND INSTALLATION >

C

D

E

F

G

H

I

J

K

M

A

B

WW

N

O

P

1.

Clean wiper arm mount as shown in the figure to prevent nuts
from being loosened.

2.

Operate front wiper motor to move the front wiper to the auto
stop position.

3.

Adjust front wiper blade position. Refer to 

WW-55, "Adjustment"

.

4.

Install front wiper arm by tightening the mounting nuts.

5.

Inject the washer fluid.

6.

Operate front wiper to move it to the auto stop position.

7.

Check that the front wiper blades stop at the specified position.

8.

Install front wiper arm caps.

Adjustment

INFOID:0000000007579591

WIPER BLADE POSITION ADJUSTMENT

Clearance between the end of cowl top cover/ front fender protector and the top of wiper blade center

Standard clearance

ELH0717D

1.

Front wiper arm LH

2.

Front wiper arm RH

3.

Cowl top cover

4.

Front fender cover 

5.

Windshield glass assembly

JMLIA1334ZZ

R

: 37.7

±

7.5 mm (1.484 

±

 0.295 in)

L

: 46.8

±

7.5 mm (1.843 

±

 0.295 in)

Revision: 2011 October

2012 JUKE

WW-56

< REMOVAL AND INSTALLATION >

FRONT WIPER BLADE

FRONT WIPER BLADE

Exploded View

INFOID:0000000007579592

Removal and Installation

INFOID:0000000007579593

REMOVAL

Push up the lever (A) of wiper blade (1), while sliding wiper blade
toward the direction of the arrow to remove it from wiper arm (2).

CAUTION:

Be careful not to drop the wiper blade onto the windshield
glass.

INSTALLATION

1.

Install wiper blade into wiper arm.

2.

Install wiper arm.

Replacement

INFOID:0000000007579594

1.

Remove the wiper blade from the wiper arm. Refer to 

WW-56, "Removal and Installation"

.

1.

Wiper arm

2.

Wiper blade

3.

Wiper refill

A

: Wiper refill end

B:

: Wiper refill tip

: Do not reuse

JMLIA1733ZZ

JMLIA1166ZZ

Revision: 2011 October

2012 JUKE

FRONT WIPER BLADE

WW-57

< REMOVAL AND INSTALLATION >

C

D

E

F

G

H

I

J

K

M

A

B

WW

N

O

P

2.

Pinch the vertebra with tenailles (A) and slide the wiper refill (2)
toward the direction of the arrow 2 to remove.
NOTE:
Be careful not to damage the wiper blade (1).

3.

Insert the new wiper refill kit (2) as shown in the figure to the wiper blade (1) until the stopper at the wiper
refill end fits into the tab on wiper blade.

NOTE:
• Insert the wiper refill to be held securely by tab of wiper blade.
• After the wiper refill is fully inserted, remove the holder (A).
• The refill kit is provided as a set attached to service parts.

4.

After installing the new wiper refill (1) check that the vertebra (2) is well inserted into the wiper refill (1).

NOTE:
Check the following items after replacing wiper refill.
• Wiper refill is not twisted at all.
• Wiper refill thoroughly fits in the tab (B) on wiper blade.
• Wiper refill is inserted from the proper direction.
• The stopper (A) is inserted into the wiper refill. 

JMLIA1737ZZ

JMLIA1738ZZ

JMLIA1734ZZ

Revision: 2011 October

2012 JUKE

WW-58

< REMOVAL AND INSTALLATION >

FRONT WIPER DRIVE ASSEMBLY

FRONT WIPER DRIVE ASSEMBLY

Exploded View

INFOID:0000000007579595

REMOVAL

DISASSEMBLY

1.

Front wiper arm cap

2.

Front wiper arm LH

3.

Front wiper blade LH

4.

Front wiper arm RH

5.

Front wiper blade RH

6.

Front wiper drive assembly

: Pawl

: N·m (kg-m, in-lb)

: N·m (kg-m, ft-lb)

JMLIA1732GB

1.

Front wiper linkage 1

2.

Shaft seal

3.

Front wiper frame

4.

Front wiper motor

5.

Front wiper linkage 2

: Nissan MP special grease No.2

JMLIA1498ZZ

Revision: 2011 October

2012 JUKE

FRONT WIPER DRIVE ASSEMBLY

WW-59

< REMOVAL AND INSTALLATION >

C

D

E

F

G

H

I

J

K

M

A

B

WW

N

O

P

Removal and Installation

INFOID:0000000007579596

REMOVAL

1.

Remove front wiper arms (LH and RH). Refer to 

WW-54, "Removal and Installation"

.

2.

Remove cowl top cover. Refer to 

EXT-20, "Removal and Installation"

.

3.

Disconnect the front wiper motor connector.

4.

Remove the mounting bolts from front wiper drive assembly.

5.

Remove the front wiper drive assembly from the vehicle.

INSTALLATION

1.

Install the front wiper drive assembly to the vehicle.

2.

Connect front wiper motor connector.

3.

Operate front wiper to move it to the auto stop position.

4.

Install cowl top cover. Refer to 

EXT-20, "Removal and Installation"

.

5.

Install front wiper arms. Refer to 

WW-54, "Removal and Installation"

.

Disassembly and Assembly

INFOID:0000000007579597

DISASSEMBLY

1.

Remove the front wiper linkage 1 and 2 from the front wiper drive assembly.

CAUTION:

Never bend the linkage or damage the plastic part of the ball joint when removing the wiper link-
age.

2.

Remove the front wiper motor mounting screws, and then remove the front wiper motor from the front
wiper frame.

ASSEMBLY

1.

Connect the front wiper motor connector.

2.

Operate the front wiper to move it to the auto stop position.

3.

Disconnect the front wiper motor connector.

4.

Install the front wiper motor to the front wiper frame.

5.

Install the front wiper linkage 2 to the front wiper motor and the front wiper frame.

6.

Install the front wiper linkage 1 to the front wiper frame.

CAUTION:

• Never drop front wiper motor or cause it to come into contact with other parts.
• Be careful for the grease condition at the front wiper motor and front wiper linkage joint

(retainer). Apply Multi

purpose grease or an equivalent if necessary.

Revision: 2011 October

2012 JUKE

WW-60

< REMOVAL AND INSTALLATION >

WIPER AND WASHER SWITCH

WIPER AND WASHER SWITCH

Exploded View

INFOID:0000000007579598

Wiper and washer switch is integrated in the combination switch. Refer to 

BCS-81, "Exploded View"

.

Revision: 2011 October

2012 JUKE

REAR WIPER ARM

WW-61

< REMOVAL AND INSTALLATION >

C

D

E

F

G

H

I

J

K

M

A

B

WW

N

O

P

REAR WIPER ARM

Exploded View

INFOID:0000000007579599

Removal and Installation

INFOID:0000000007579600

REMOVAL

1.

Operate rear wiper to the auto stop position.

2.

Remove rear wiper arm cover.

3.

Remove rear wiper arm mounting nut.

4.

Remove wiper arm from the vehicle.

INSTALLATION

1.

Clean wiper arm mount as shown in the figure to prevent nut
from being loosened.

2.

Operate the rear wiper motor to the auto stop position.

3.

Adjust the rear wiper blade position. Refer to 

WW-61, "Adjust-

ment"

.

4.

Install the rear wiper arm by tightening the mounting nut.

5.

Inject the washer fluid.

6.

Operate the rear wiper to the auto stop position.

7.

Check that the rear wiper blades stop at the specified position.

8.

Install the rear wiper arm cover.

Adjustment

INFOID:0000000007579601

REAR WIPER BLADE POSITION ADJUSTMENT

1.

Rear wiper motor

2.

Rear wiper blade

3.

Rear wiper arm

4.

Rear wiper arm cover

5.

Rear wiper pivot seal

A

: Canada models only

: Pawl

: N·m (kg-m, in-lb)

: N·m (kg-m, ft-lb)

JMLIA1503GB

SKIA0082J

Revision: 2011 October

2012 JUKE

WW-62

< REMOVAL AND INSTALLATION >

REAR WIPER ARM

Set the wiper blade top on the defrosting wire (A) (clearance between the end of back door glass and the top
of wiper blade center).

Standard clearance

1.

Rear wiper blade

2.

Back door window glass

3.

Back door panel

A

: Rear defogger wire print

L

: 67.5 

±

 7.5 mm (2.657 

±

 0.295in)

JMLIA1170ZZ

Revision: 2011 October

2012 JUKE

REAR WIPER MOTOR

WW-63

< REMOVAL AND INSTALLATION >

C

D

E

F

G

H

I

J

K

M

A

B

WW

N

O

P

REAR WIPER MOTOR

Exploded View

INFOID:0000000007579602

Removal and Installation

INFOID:0000000007579603

REMOVAL

1.

Remove rear wiper arm. Refer to 

WW-61, "Removal and Installation"

.

2.

Remove back door lower finisher. Refer to 

INT-38, "BACK DOOR SIDE FINISHER : Removal and Installa-

tion"

.

3.

Disconnect rear wiper motor connector.

4.

Remove rear wiper motor mounting bolts.

5.

Remove rear wiper motor from the vehicle.

6.

Remove the pivot seal.

INSTALLATION

Install in the reverse order of removal.

1.

Rear wiper motor

2.

Rear wiper blade

3.

Rear wiper arm

4.

Rear wiper arm cover

5.

Rear wiper pivot seal

A

: Canada models only

: Pawl

: N·m (kg-m, in-lb)

: N·m (kg-m, ft-lb)

JMLIA1503GB

Revision: 2011 October

2012 JUKE

WW-64

< REMOVAL AND INSTALLATION >

REAR WASHER NOZZLE AND TUBE

REAR WASHER NOZZLE AND TUBE

Hydraulic Layout

INFOID:0000000007579604

Removal and Installation

INFOID:0000000007579605

REMOVAL

1.

Remove luggage side upper finisher RH. Refer to 

INT-35, "LUGGAGE SIDE UPPER FINISHER :

Removal and Installation"

.

2.

Disconnect rear washer tube (2) fixing clip and then remove rear
washer tube joint (2) from rear washer tube.

1.

Rear washer nozzle

2.

Plug

3.

Rear washer tube

4.

Joint

5.

Second washer tube

6.

Back door seal rubber

7.

Front washer tube

: Clip

: Pawl

JMLIA1221ZZ

: Clip

JMLIA1222ZZ

Revision: 2011 October

2012 JUKE

REAR WASHER NOZZLE AND TUBE

WW-65

< REMOVAL AND INSTALLATION >

C

D

E

F

G

H

I

J

K

M

A

B

WW

N

O

P

3.

Fully open back door.

4.

Remove back door seal rubber (2), and then remove rear
washer tube (3) from back door seal rubber.

5.

Remove plug (1).

6.

Disengage rear washer nozzle (1) fixing pawl with a flat-bladed
screwdriver (A) and remove the rear washer nozzle.

CAUTION:

Wrap the flat-bladed screwdriver into a protective tape (B)
to protect the part from damage.

7.

Remove rear washer nozzle from the rear washer tube.

INSTALLATION

Install in the reverse order of removal.

Inspection and Adjustment

INFOID:0000000007579606

INSPECTION

Washer Nozzle Inspection

Check that air can pass through the hose by blowing forward (toward
the nozzle), and check that air cannot pass through by sucking.

ADJUSTMENT

Washer Nozzle Spray Position adjustment

JMLIA1223ZZ

JMLIA1224ZZ

JMLIA1171ZZ

Revision: 2011 October

2012 JUKE

 

 

 

 

 

 

 

Content      ..     244      245      246      247     ..