Nissan Juke (2012 year). Service Repair Manual

B1339 SATELLITE SENSOR RH

SRC-151

< DTC/CIRCUIT DIAGNOSIS >

SRC

B1339 SATELLITE SENSOR RH

DTC Logic

INFOID:0000000007578385

DTC DETECTION LOGIC

DTC CONFIRMATION PROCEDURE

CHECK SELF-DIAG RESULT

With CONSULT

Turn ignition switch ON.

Perform “Self Diagnostic Result” mode of “AIR BAG” using CONSULT.

Without CONSULT

Turn ignition switch ON.

Check the air bag warning lamp status. Refer to

SRC-11, "On Board Diagnosis Function"

NOTE:
SRS does not enter the diagnosis mode if no malfunction is detected in the user mode.

Is malfunctioning part detected?

YES

>> Refer to

SRC-151, "Diagnosis Procedure"

>> INSPECTION END

Diagnosis Procedure

INFOID:0000000007578386

WARNING:

• Before servicing, turn ignition switch OFF, disconnect battery negative terminal, and wait at least 3

minutes or more. (To discharge backup capacitor.)

• Never use unspecified tester or other measuring device.

REPLACE FRONT DOOR SATELLITE SENSOR

Replace front door satellite sensor RH. Refer to

SR-24, "Removal and Installation"

Perform DTC confirmation procedure. Refer to

SRC-151, "DTC Logic"

Is DTC detected?

YES

>> GO TO 2.

>> INSPECTION END

REPLACE AIR BAG DIAGNOSIS SENSOR UNIT

Replace air bag diagnosis sensor unit. Refer to

SR-27, "Removal and Installation"

Perform DTC confirmation procedure. Refer to

SRC-151, "DTC Logic"

Is DTC detected?

YES

>> GO TO 1.

>> INSPECTION END

DTC

Display contents of

CONSULT

DTC detecting condition

Possible cause

B1339

FR-RH DOOR SATEL
SENS
[MIS-INSTALLATION]

Front door satellite sensor RH is out of the
specified specification

Diagnosis sensor unit or front door satellite sen-
sor RH is different from the part specified

Revision: 2011 October

2012 JUKE

SRC-152

< DTC/CIRCUIT DIAGNOSIS >

B1343, B1344 SATELLITE SENSOR LH

B1343, B1344 SATELLITE SENSOR LH

DTC Logic

INFOID:0000000007578387

DTC DETECTION LOGIC

DTC CONFIRMATION PROCEDURE

CHECK SELF-DIAG RESULT

With CONSULT

Turn ignition switch ON.

Perform “Self Diagnostic Result” mode of “AIR BAG” using CONSULT.

Without CONSULT

Turn ignition switch ON.

Check the air bag warning lamp status. Refer to

SRC-11, "On Board Diagnosis Function"

NOTE:
SRS does not enter the diagnosis mode if no malfunction is detected in the user mode.

Is malfunctioning part detected?

YES

>> Refer to

SRC-152, "Diagnosis Procedure"

>> INSPECTION END

Diagnosis Procedure

INFOID:0000000007578388

WARNING:

• Before servicing, turn ignition switch OFF, disconnect battery negative terminal, and wait at least 3

minutes or more. (To discharge backup capacitor.)

• Never use unspecified tester or other measuring device.

CHECK HARNESS CONNECTOR

Check the harness connector.

Is the inspection result normal?

YES

>> GO TO 2.

>> Replace harness connector.

CHECK WIRING HARNESS

Check the wiring harness externals.

Is the inspection result normal?

YES

>> GO TO 3.

>> Replace wiring harness.

REPLACE FRONT DOOR SATELLITE SENSOR

Replace front door satellite sensor LH. Refer to

SR-24, "Removal and Installation"

Perform DTC confirmation procedure. Refer to

SRC-152, "DTC Logic"

Is DTC detected?

YES

>> GO TO 4.

>> INSPECTION END

REPLACE AIR BAG DIAGNOSIS SENSOR UNIT

Replace air bag diagnosis sensor unit. Refer to

SR-27, "Removal and Installation"

Perform DTC confirmation procedure. Refer to

SRC-152, "DTC Logic"

Is DTC detected?

DTC

Display contents of

CONSULT

DTC detecting condition

Possible cause

B1343
B1344

FR-LH DOOR SATEL
SENS
[SENSOR MALFUNC-
TION]

Front door satellite sensor LH is malfunc-
tioning

• Harness or connectors
• Malfunction in front door satellite sensor LH
• Malfunction in air bag diagnosis sensor unit

Revision: 2011 October

2012 JUKE

B1343, B1344 SATELLITE SENSOR LH

SRC-153

< DTC/CIRCUIT DIAGNOSIS >

SRC

YES

>> GO TO 1.

>> INSPECTION END

Revision: 2011 October

2012 JUKE

SRC-154

< DTC/CIRCUIT DIAGNOSIS >

B1345, B1347, B1348, B1349 SATELLITE SENSOR LH

B1345, B1347, B1348, B1349 SATELLITE SENSOR LH

DTC Logic

INFOID:0000000007578389

DTC DETECTION LOGIC

DTC CONFIRMATION PROCEDURE

CHECK SELF-DIAG RESULT

With CONSULT

Turn ignition switch ON.

Perform “Self Diagnostic Result” mode of “AIR BAG” using CONSULT.

Without CONSULT

Turn ignition switch ON.

Check the air bag warning lamp status. Refer to

SRC-11, "On Board Diagnosis Function"

NOTE:
SRS does not enter the diagnosis mode if no malfunction is detected in the user mode.
Is malfunctioning part detected?

YES

>> Refer to

SRC-157, "Diagnosis Procedure"

>> INSPECTION END

Diagnosis Procedure

INFOID:0000000007578390

WARNING:

• Before servicing, turn ignition switch OFF, disconnect battery negative terminal, and wait at least 3

minutes or more. (To discharge backup capacitor.)

• Never use unspecified tester or other measuring device.

CHECK HARNESS CONNECTOR

Check the harness connector.
Is the inspection result normal?

YES

>> GO TO 2.

>> Replace harness connector.

CHECK WIRING HARNESS

Check the wiring harness externals.

Is the inspection result normal?

YES

>> GO TO 3.

>> Replace wiring harness.

REPLACE SATELLITE SENSOR

Replace front door satellite sensor LH. Refer to

SR-24, "Removal and Installation"

Perform DTC confirmation procedure. Refer to

SRC-157, "DTC Logic"

Is DTC detected?

YES

>> GO TO 4.

>> INSPECTION END

REPLACE AIR BAG DIAGNOSIS SENSOR UNIT

Replace air bag diagnosis sensor unit. Refer to

SR-27, "Removal and Installation"

Perform DTC confirmation procedure. Refer to

SRC-157, "DTC Logic"

Is DTC detected?

DTC

Display contents of

CONSULT

DTC detecting condition

Possible cause

B1345
B1347
B1348
B1349

FR-LH DOOR SATEL
SENS
[COMM MALFUNC-
TION]

Front door satellite sensor LH is malfunc-
tioning

• Harness or connectors
• Malfunction in front door satellite sensor LH
• Malfunction in air bag diagnosis sensor unit

Revision: 2011 October

2012 JUKE

B1345, B1347, B1348, B1349 SATELLITE SENSOR LH

SRC-155

< DTC/CIRCUIT DIAGNOSIS >

SRC

YES

>> GO TO 1.

>> INSPECTION END

Revision: 2011 October

2012 JUKE

SRC-156

< DTC/CIRCUIT DIAGNOSIS >

B1346 SATELLITE SENSOR LH

B1346 SATELLITE SENSOR LH

DTC Logic

INFOID:0000000007578391

DTC DETECTION LOGIC

DTC CONFIRMATION PROCEDURE

CHECK SELF-DIAG RESULT

With CONSULT

Turn ignition switch ON.

Perform “Self Diagnostic Result” mode of “AIR BAG” using CONSULT.

Without CONSULT

Turn ignition switch ON.

Check the air bag warning lamp status. Refer to

SRC-11, "On Board Diagnosis Function"

NOTE:
SRS does not enter the diagnosis mode if no malfunction is detected in the user mode.

Is malfunctioning part detected?

YES

>> Refer to

SRC-156, "Diagnosis Procedure"

>> INSPECTION END

Diagnosis Procedure

INFOID:0000000007578392

WARNING:

• Before servicing, turn ignition switch OFF, disconnect battery negative terminal, and wait at least 3

minutes or more. (To discharge backup capacitor.)

• Never use unspecified tester or other measuring device.

REPLACE FRONT DOOR SATELLITE SENSOR

Replace front door satellite sensor LH. Refer to

SR-24, "Removal and Installation"

Perform DTC confirmation procedure. Refer to

SRC-156, "DTC Logic"

Is DTC detected?

YES

>> GO TO 2.

>> INSPECTION END

REPLACE AIR BAG DIAGNOSIS SENSOR UNIT

Replace air bag diagnosis sensor unit. Refer to

SR-27, "Removal and Installation"

Perform DTC confirmation procedure. Refer to

SRC-156, "DTC Logic"

Is DTC detected?

YES

>> GO TO 1.

>> INSPECTION END

DTC

Display contents of

CONSULT

DTC detecting condition

Possible cause

B1346

FR-LH DOOR SATEL
SENS
[MIS-INSTALLATION]

Front door satellite sensor LH is out of the
specified specification

Diagnosis sensor unit or front door satellite sen-
sor LH is different from the part specified

Revision: 2011 October

2012 JUKE

B1350, B1351 SATELLITE SENSOR

SRC-157

< DTC/CIRCUIT DIAGNOSIS >

SRC

B1350, B1351 SATELLITE SENSOR

DTC Logic

INFOID:0000000007578393

DTC DETECTION LOGIC

DTC CONFIRMATION PROCEDURE

CHECK SELF-DIAG RESULT

With CONSULT

Turn ignition switch ON.

Perform “Self Diagnostic Result” mode of “AIR BAG” using CONSULT.

Without CONSULT

Turn ignition switch ON.

Check the air bag warning lamp status. Refer to

SRC-11, "On Board Diagnosis Function"

NOTE:
SRS does not enter the diagnosis mode if no malfunction is detected in the user mode.

Is malfunctioning part detected?

YES

>> Refer to

SRC-157, "Diagnosis Procedure"

>> INSPECTION END

Diagnosis Procedure

INFOID:0000000007578394

WARNING:

• Before servicing, turn ignition switch OFF, disconnect battery negative terminal, and wait at least 3

minutes or more. (To discharge backup capacitor.)

• Never use unspecified tester or other measuring device.

REPLACE BOTH OF FRONT DOOR SATELLITE SENSOR

Replace both of front door satellite sensor. Refer to

SR-24, "Removal and Installation"

Perform DTC confirmation procedure. Refer to

SRC-157, "DTC Logic"

Is DTC detected?

YES

>> GO TO 2.

>> INSPECTION END

REPLACE AIR BAG DIAGNOSIS SENSOR UNIT

Replace air bag diagnosis sensor unit. Refer to

SR-27, "Removal and Installation"

Perform DTC confirmation procedure. Refer to

SRC-157, "DTC Logic"

Is DTC detected?

YES

>> GO TO 1.

>> INSPECTION END

DTC

Display contents of

CONSULT

DTC detecting condition

Possible cause

B1350
B1351

FR DOOR SATEL SENS

Front door satellite sensor is malfunction-
ing or out of the specified specification

• Malfunction in front door satellite sensor LH/RH
• Malfunction in air bag diagnosis sensor unit

Revision: 2011 October

2012 JUKE

SRC-158

< SYMPTOM DIAGNOSIS >

SRS AIR BAG WARNING LAMP DOES NOT TURN OFF

SYMPTOM DIAGNOSIS

SRS AIR BAG WARNING LAMP DOES NOT TURN OFF

Diagnosis Procedure

INFOID:0000000007578395

CHECK AIR BAG MODULE AND SEAT BELT PRE-TENSIONER

Check the deployment of air bag module and seat belt pre-tensioner.

Is air bag module deployed?

YES

>> Replace the malfunctioning parts.

>> GO TO 2.

CHECK AIR BAG FUSE

Check 10 A fuse [No.2, located in fuse block (J/B)].

Is the inspection result normal?

YES

>> GO TO 3.

>> Replace the fuse.

CHECK HARNESS CONNECTOR

Check the harness connector.

Is the inspection result normal?

YES

>> GO TO 4.

>> Replace harness connectors.

CHECK WIRING HARNESS

Check the wiring harness externals.
Is the inspection result normal?

YES

>> GO TO 5.

>> Replace wiring harness.

REPLACE AIR BAG DIAGNOSIS SENSOR UNIT

Replace air bag diagnosis sensor unit. Refer to

SR-27, "Removal and Installation"

Check air bag warning lamp operation.

Is the inspection result normal?

YES

>> INSPECTION END

>> GO TO 6.

REPLACE COMBINATION METER

Replace combination meter. Refer to

MWI-53, "Removal and Installation"

Check air bag warning lamp operation.

Is the inspection result normal?

YES

>> INSPECTION END

>> GO TO 1.

Revision: 2011 October

2012 JUKE

SRS AIR BAG WARNING LAMP DOES NOT TURN ON

SRC-159

< SYMPTOM DIAGNOSIS >

SRC

SRS AIR BAG WARNING LAMP DOES NOT TURN ON

Diagnosis Procedure

INFOID:0000000007578396

CHECK COMBINATION METER POWER SUPPLY AND GROUND CIRCUIT

Check combination meter unit power supply and ground circuit. Refer to

MWI-42, "COMBINATION METER :

Diagnosis Procedure"

Is the inspection result normal?

YES

>> GO TO 2.

>> Repair or replace the malfunctioning parts.

CHECK HARNESS CONNECTOR

Check the harness connector.

Is the inspection result normal?

YES

>> GO TO 3.

>> Replace harness connectors.

CHECK WIRING HARNESS

Check the wiring harness externals.
Is the inspection result normal?

YES

>> GO TO 4.

>> Replace wiring harness.

CHECK AIR BAG DIAGNOSIS SENSOR UNIT

Disconnect air bag diagnosis sensor unit connector and turn ignition switch ON.

Does air bag warning lamp turn ON?

YES

>> Replace air bag diagnosis sensor unit. Refer to

SR-27, "Removal and Installation"

>> Replace combination meter. Refer to

MWI-53, "Removal and Installation"

Revision: 2011 October

2012 JUKE

SRC-160

< SYMPTOM DIAGNOSIS >

SRS AIR BAG WARNING LAMP BLINKS

SRS AIR BAG WARNING LAMP BLINKS

Diagnosis Procedure

INFOID:0000000007578397

PERFORM ZERO POINT REST

Perform zero point reset. Refer to

SRC-28, "ZERO POINT RESET : Special Repair Requirement"

Is the inspection result normal?

YES

>> GO TO 2.

>> Repair or replace malfunctioning parts.

CHECK BATTERY

Check battery. Refer to

PG-88, "How to Handle Battery"

Is the inspection result normal?

YES

>> GO TO 3.

>> Repair or replace malfunctioning parts.

REPLACE AIR BAG DIAGNOSIS SENSOR UNIT

Replace air bag diagnosis sensor unit. Refer to

SR-27, "Removal and Installation"

Check air bag warning lamp operation.

Is the inspection result normal?

YES

>> INSPECTION END

>> GO TO 4.

REPLACE OCCUPANT DETECTION SYSTEM CONTROL UNIT

Replace seat cushion frame. Refer to

SE-18, "Removal and Installation"

Check air bag warning lamp operation.

Is the inspection result normal?

YES

>> INSPECTION END

>> GO TO 1.

Revision: 2011 October

2012 JUKE

ST-2

< PRECAUTION >

PRECAUTIONS

PRECAUTION

PRECAUTIONS

Precaution for Supplemental Restraint System (SRS) "AIR BAG" and "SEAT BELT
PRE-TENSIONER"

INFOID:0000000007577729

The Supplemental Restraint System such as “AIR BAG” and “SEAT BELT PRE-TENSIONER”, used along
with a front seat belt, helps to reduce the risk or severity of injury to the driver and front passenger for certain
types of collision. This system includes seat belt switch inputs and dual stage front air bag modules. The SRS
system uses the seat belt switches to determine the front air bag deployment, and may only deploy one front
air bag, depending on the severity of a collision and whether the front occupants are belted or unbelted.
Information necessary to service the system safely is included in the “SRS AIR BAG” and “SEAT BELT” of this
Service Manual.

WARNING:

Always observe the following items for preventing accidental activation.
• To avoid rendering the SRS inoperative, which could increase the risk of personal injury or death in

the event of a collision that would result in air bag inflation, all maintenance must be performed by
an authorized NISSAN/INFINITI dealer.

• Improper maintenance, including incorrect removal and installation of the SRS, can lead to personal

injury caused by unintentional activation of the system. For removal of Spiral Cable and Air Bag
Module, see “SRS AIR BAG”.

• Never use electrical test equipment on any circuit related to the SRS unless instructed to in this Ser-

vice Manual. SRS wiring harnesses can be identified by yellow and/or orange harnesses or harness
connectors.

PRECAUTIONS WHEN USING POWER TOOLS (AIR OR ELECTRIC) AND HAMMERS

WARNING:

Always observe the following items for preventing accidental activation.
• When working near the Air Bag Diagnosis Sensor Unit or other Air Bag System sensors with the

ignition ON or engine running, never use air or electric power tools or strike near the sensor(s) with
a hammer. Heavy vibration could activate the sensor(s) and deploy the air bag(s), possibly causing
serious injury.

• When using air or electric power tools or hammers, always switch the ignition OFF, disconnect the

battery, and wait at least 3 minutes before performing any service.

Service Notice or Precautions for Steering System

INFOID:0000000007577730

• In case of removing steering gear assembly, make the final tightening with grounded and unloaded vehicle

condition, and then check wheel alignment.

• Observe the following precautions when disassembling.
- Before disassembly, thoroughly clean the outside of the unit.
- Disassembly should be done in a clean work area. It is important to prevent the internal parts from becoming

contaminated by dirt or other foreign matter.

- For easier and proper assembly, place disassembled parts in order on a parts rack.
- Use nylon cloth or paper towels to clean the parts; common shop rags can leave lint that might interfere with

their operation.

- Never reuse non-reusable parts.
- Before assembling, apply the specified grease to the directed parts.
• During quick steering, rasping noise may be heard from around the steering wheel. This is not a malfunction.

The noise is an operating noise of the EPS system under normal conditions. If the rasping noise occurs dur-
ing slow steering, this may not be an operating noise of the system. In this case, it is necessary to find out
the location of the noise and repair, if necessary.

• Never repeat static steering. (Motor and EPS control unit could be heated.)

Revision: 2012 February

2012 JUKE

PREPARATION

ST-3

< PREPARATION >

PREPARATION

Special Service Tools

INFOID:0000000007577731

The actual shapes of Kent-Moore tools may differ from those of special service tools illustrated here.

Commercial Service Tools

INFOID:0000000007577732

Tool number
(Kent-Moore No.)
Tool name

Description

ST27180001
(J-25726-A)
Steering wheel puller

Removing steering wheel

ST3127S000
(J-25765-A)
Preload gauge

Measuring steering column rotating torque

KV40107300
(

—

)

Boot band crimping tool

Installing boot clamp (large diameter)

ZZA0819D

ZZA0806D

ZZA1229D

Tool name

Description

Ball joint remover

Removing steering outer socket

Power tool

Loosening bolts and nuts

S-NT146

PBIC0190E

Revision: 2012 February

2012 JUKE

ST-4

< BASIC INSPECTION >

STEERING WHEEL

BASIC INSPECTION

STEERING WHEEL

Inspection

INFOID:0000000007577733

NEUTRAL POSITION STEERING WHEEL

Make sure that steering gear assembly, steering column assembly and steering wheel are installed in the
correct position.

Perform neutral position inspection after wheel alignment. Refer to

FSU-6, "Inspection"

Set vehicle to the straight-ahead position and confirm steering wheel is in the neutral position.

Loosen outer socket lock nut and turn inner socket to left and right equally to make fine adjustments if
steering wheel is not in the neutral position.

STEERING WHEEL TURNING FORCE

Park vehicle on a level and dry surface, set parking brake.

Tires need to be inflated normal pressure. Refer to

WT-50, "Tire Air Pressure"

Start engine.

Check steering wheel turning force when steering wheel has
been turned 360

from neutral position.

NOTE:
Multiply the distance from the hook of spring balance to the cen-
ter of steering wheel by the measurement value with a spring
balance.

FRONT WHEEL TURNING ANGLE

Check front wheel turning angle after toe-in inspection. Refer to

FSU-6, "Inspection"

Place front wheels on turning radius gauges and rear wheels on
stands, so that vehicle can be level.

Check the maximum inner and outer wheel turning angles for LH
and RH road wheels.

With the engine at idle, turn steering wheel from full left stop to
full right stop and measure the turning angles.

Steering wheel turning
force

: Refer to

ST-19, "Steering

Wheel"

: 185 mm (7.28 in)

JSGIA0027ZZ

FAA0016D

Inner wheel (Angle: A)

: Refer to

ST-19, "Steering

Angle"

Outer wheel (Angle: B)

: Refer to

ST-19, "Steering

Angle"

SGIA0055E

Revision: 2012 February

2012 JUKE

STEERING WHEEL

ST-5

< BASIC INSPECTION >

Check the following items when turning angle is out of the stan-
dard.

Check rack stroke (L).

If rack stroke is out of specification, replace steering gear
assembly.
• Steering angles are not adjustable. Check steering gear

assembly, steering column assembly, and front suspension
components for wear or damage if any of the turning angles are different from the specified value.
Replace any of them, if any non-standard condition exists.

Rack stroke neutral position (L)

: Refer to

ST-19,

"Steering Gear and
Linkage"

JSGIA0272ZZ

Revision: 2012 February

2012 JUKE

Nissan Juke (2012 year). Service Repair Manual - part 215