Nissan Juke (2012 year). Service Repair Manual

B1154, B1155, B1156, B1157, B1158, B1159 DIAGNOSIS SENSOR UNIT

SRC-135

< DTC/CIRCUIT DIAGNOSIS >

SRC

B1154, B1155, B1156, B1157, B1158, B1159 DIAGNOSIS SENSOR UNIT

DTC Logic

INFOID:0000000007578359

DTC DETECTION LOGIC

DTC CONFIRMATION PROCEDURE

CHECK SELF-DIAG RESULT

With CONSULT

Turn ignition switch ON.

Perform “Self Diagnostic Result” mode of “AIR BAG” using CONSULT.

Without CONSULT

Turn ignition switch ON.

Check the air bag warning lamp status. Refer to

SRC-11, "On Board Diagnosis Function"

NOTE:
SRS does not enter the diagnosis mode if no malfunction is detected in the user mode.

Is malfunctioning part detected?

YES

>> Refer to

SRC-135, "Diagnosis Procedure"

>> INSPECTION END

Diagnosis Procedure

INFOID:0000000007578360

WARNING:

• Before servicing, turn ignition switch OFF, disconnect battery negative terminal, and wait at least 3

minutes or more. (To discharge backup capacitor.)

• Never use unspecified tester or other measuring device.

CHECK HARNESS CONNECTOR

Check the harness connector.

Is the inspection result normal?

YES

>> GO TO 2.

>> Replace harness connectors.

CHECK WIRING HARNESS

Check the wiring harness externals.

Is the inspection result normal?

YES

>> GO TO 3.

>> Replace wiring harness.

REPLACE AIR BAG DIAGNOSIS SENSOR UNIT

Replace air bag diagnosis sensor unit. Refer to

SR-27, "Removal and Installation"

Perform DTC confirmation procedure. Refer to

SRC-135, "DTC Logic"

Is DTC detected?

YES

>> GO TO 1.

>> INSPECTION END

DTC

Display contents of

CONSULT

DTC detecting condition

Possible cause

B1154
B1155
B1156
B1157
B1158
B1159

CONTROL UNIT

Air bag diagnosis sensor unit is malfunctioning

Malfunction in air bag diagnosis sensor unit

Revision: 2011 October

2012 JUKE

SRC-136

< DTC/CIRCUIT DIAGNOSIS >

B1170, B1171, B1172, B1173, B1174, B1175 DIAGNOSIS SENSOR UNIT

B1170, B1171, B1172, B1173, B1174, B1175 DIAGNOSIS SENSOR UNIT

DTC Logic

INFOID:0000000007578361

DTC DETECTION LOGIC

DTC CONFIRMATION PROCEDURE

CHECK SELF-DIAG RESULT

With CONSULT

Turn ignition switch ON.

Perform “Self Diagnostic Result” mode of “AIR BAG” using CONSULT.

Without CONSULT

Turn ignition switch ON.

Check the air bag warning lamp status. Refer to

SRC-11, "On Board Diagnosis Function"

NOTE:
SRS does not enter the diagnosis mode if no malfunction is detected in the user mode.

Is malfunctioning part detected?

YES

>> Refer to

SRC-136, "Diagnosis Procedure"

>> INSPECTION END

Diagnosis Procedure

INFOID:0000000007578362

WARNING:

• Before servicing, turn ignition switch OFF, disconnect battery negative terminal, and wait at least 3

minutes or more. (To discharge backup capacitor.)

• Never use unspecified tester or other measuring device.

CHECK HARNESS CONNECTOR

Check the harness connector.

Is the inspection result normal?

YES

>> GO TO 2.

>> Replace harness connectors.

CHECK WIRING HARNESS

Check the wiring harness externals.
Is the inspection result normal?

YES

>> GO TO 3.

>> Replace wiring harness.

REPLACE AIR BAG DIAGNOSIS SENSOR UNIT

Replace air bag diagnosis sensor unit. Refer to

SR-27, "Removal and Installation"

Perform DTC confirmation procedure. Refer to

SRC-136, "DTC Logic"

Is DTC detected?

YES

>> GO TO 1.

>> INSPECTION END

DTC

Display contents of

CONSULT

DTC detecting condition

Possible cause

B1170
B1171
B1172
B1173
B1174
B1175

CONTROL UNIT

Air bag diagnosis sensor unit is malfunctioning

Malfunction in air bag diagnosis sensor unit

Revision: 2011 October

2012 JUKE

B1186, B1187, B1188, B1189, B1190, B1191 DIAGNOSIS SENSOR UNIT

SRC-137

< DTC/CIRCUIT DIAGNOSIS >

SRC

B1186, B1187, B1188, B1189, B1190, B1191 DIAGNOSIS SENSOR UNIT

DTC Logic

INFOID:0000000007578363

DTC DETECTION LOGIC

DTC CONFIRMATION PROCEDURE

CHECK SELF-DIAG RESULT

With CONSULT

Turn ignition switch ON.

Perform “Self Diagnostic Result” mode of “AIR BAG” using CONSULT.

Without CONSULT

Turn ignition switch ON.

Check the air bag warning lamp status. Refer to

SRC-11, "On Board Diagnosis Function"

NOTE:
SRS does not enter the diagnosis mode if no malfunction is detected in the user mode.

Is malfunctioning part detected?

YES

>> Refer to

SRC-137, "Diagnosis Procedure"

>> INSPECTION END

Diagnosis Procedure

INFOID:0000000007578364

WARNING:

• Before servicing, turn ignition switch OFF, disconnect battery negative terminal, and wait at least 3

minutes or more. (To discharge backup capacitor.)

• Never use unspecified tester or other measuring device.

CHECK HARNESS CONNECTOR

Check the harness connector.

Is the inspection result normal?

YES

>> GO TO 2.

>> Replace harness connectors.

CHECK WIRING HARNESS

Check the wiring harness externals.

Is the inspection result normal?

YES

>> GO TO 3.

>> Replace wiring harness.

REPLACE AIR BAG DIAGNOSIS SENSOR UNIT

Replace air bag diagnosis sensor unit. Refer to

SR-27, "Removal and Installation"

Perform DTC confirmation procedure. Refer to

SRC-137, "DTC Logic"

Is DTC detected?

YES

>> GO TO 1.

>> INSPECTION END

DTC

Display contents of

CONSULT

DTC detecting condition

Possible cause

B1186
B1187
B1188
B1189
B1190
B1191

CONTROL UNIT

Air bag diagnosis sensor unit is malfunctioning

Malfunction in air bag diagnosis sensor unit

Revision: 2011 October

2012 JUKE

SRC-138

< DTC/CIRCUIT DIAGNOSIS >

B1202, B1203, B1204, B1205, B1206, B1207 DIAGNOSIS SENSOR UNIT

B1202, B1203, B1204, B1205, B1206, B1207 DIAGNOSIS SENSOR UNIT

DTC Logic

INFOID:0000000007578365

DTC DETECTION LOGIC

DTC CONFIRMATION PROCEDURE

CHECK SELF-DIAG RESULT

With CONSULT

Turn ignition switch ON.

Perform “Self Diagnostic Result” mode of “AIR BAG” using CONSULT.

Without CONSULT

Turn ignition switch ON.

Check the air bag warning lamp status. Refer to

SRC-11, "On Board Diagnosis Function"

NOTE:
SRS does not enter the diagnosis mode if no malfunction is detected in the user mode.

Is malfunctioning part detected?

YES

>> Refer to

SRC-138, "Diagnosis Procedure"

>> INSPECTION END

Diagnosis Procedure

INFOID:0000000007578366

WARNING:

• Before servicing, turn ignition switch OFF, disconnect battery negative terminal, and wait at least 3

minutes or more. (To discharge backup capacitor.)

• Never use unspecified tester or other measuring device.

CHECK HARNESS CONNECTOR

Check the harness connector.

Is the inspection result normal?

YES

>> GO TO 2.

>> Replace harness connectors.

CHECK WIRING HARNESS

Check the wiring harness externals.
Is the inspection result normal?

YES

>> GO TO 3.

>> Replace wiring harness.

REPLACE AIR BAG DIAGNOSIS SENSOR UNIT

Replace air bag diagnosis sensor unit. Refer to

SR-27, "Removal and Installation"

Perform DTC confirmation procedure. Refer to

SRC-138, "DTC Logic"

Is DTC detected?

YES

>> GO TO 1.

>> INSPECTION END

DTC

Display contents of

CONSULT

DTC detecting condition

Possible cause

B1202
B1203
B1204
B1205
B1206
B1207

CONTROL UNIT

Air bag diagnosis sensor unit is malfunctioning

Malfunction in air bag diagnosis sensor unit

Revision: 2011 October

2012 JUKE

B1209 FRONTAL COLLISION DETECTION

SRC-139

< DTC/CIRCUIT DIAGNOSIS >

SRC

B1209 FRONTAL COLLISION DETECTION

Description

INFOID:0000000007578367

The air bags and seat belt pre-tensioners for driver and passenger are activated by the air bag diagnosis sen-
sor unit signal transmitted at the time of the frontal collision.

DTC Logic

INFOID:0000000007578368

DTC DETECTION LOGIC

DTC CONFIRMATION PROCEDURE

CHECK SELF-DIAG RESULT

With CONSULT

Turn ignition switch ON.

Perform “Self Diagnostic Result” mode of “AIR BAG” using CONSULT.

Without CONSULT

Turn ignition switch ON.

Check the air bag warning lamp status. Refer to

SRC-11, "On Board Diagnosis Function"

NOTE:
SRS does not enter the diagnosis mode if no malfunction is detected in the user mode.

Is malfunctioning part detected?

YES

>> Refer to

SRC-139, "Diagnosis Procedure"

>> INSPECTION END

Diagnosis Procedure

INFOID:0000000007578369

WARNING:

• Before servicing, turn ignition switch OFF, disconnect battery negative terminal, and wait at least 3

minutes or more. (To discharge backup capacitor.)

• Never use unspecified tester or other measuring device.

PERFORM COLLISION DIAGNOSIS

Perform collision diagnosis. Refer to

SR-4, "FOR FRONTAL COLLISION : When SRS is activated in a colli-

sion"

SR-5, "FOR FRONTAL COLLISION : When SRS is not activated in a collision"

Is collision diagnosis complete?

YES

>> GO TO 2.

>> INSPECTION END

FINAL INSPECTION

Perform “AIR BAG” Self Diagnostic Result.
Is the inspection result normal?

YES

>> INSPECTION END

>> Perform diagnosis of applicable DTC. Refer to

SRC-19, "DTC Index"

DTC

Display contents of

CONSULT

DTC detecting condition

Possible cause

B1209

FRONTAL COLLI-
SION DETECTION

Seat belt pre-tensioner, driver side air bag and passen-
ger air bag are deployed

—

Revision: 2011 October

2012 JUKE

SRC-140

< DTC/CIRCUIT DIAGNOSIS >

B1210 SIDE COLLISION DETECTION

B1210 SIDE COLLISION DETECTION

Description

INFOID:0000000007578370

The side air bag and curtain air bag are activated by the air bag diagnosis sensor unit signal transmitted at the
time of side collision.

DTC Logic

INFOID:0000000007578371

DTC DETECTION LOGIC

DTC CONFIRMATION PROCEDURE

CHECK SELF-DIAG RESULT

With CONSULT

Turn ignition switch ON.

Perform “Self Diagnostic Result” mode of “AIR BAG” using CONSULT.

Without CONSULT

Turn ignition switch ON.

Check the air bag warning lamp status. Refer to

SRC-11, "On Board Diagnosis Function"

NOTE:
SRS does not enter the diagnosis mode if no malfunction is detected in the user mode.

Is malfunctioning part detected?

YES

>> Refer to

SRC-140, "Diagnosis Procedure"

>> INSPECTION END

Diagnosis Procedure

INFOID:0000000007578372

WARNING:

• Before servicing, turn ignition switch OFF, disconnect battery negative terminal, and wait at least 3

minutes or more. (To discharge backup capacitor.)

• Never use unspecified tester or other measuring device.

PERFORM COLLISION DIAGNOSIS

Perform collision diagnosis. Refer to

SR-6, "FOR SIDE AND ROLLOVER COLLISION : When SRS is acti-

vated in a collision"

SR-7, "FOR SIDE AND ROLLOVER COLLISION : When SRS is not activated in a colli-

sion"

Is collision diagnosis complete?

YES

>> GO TO 2.

>> INSPECTION END

FINAL INSPECTION

Perform “AIR BAG” Self Diagnostic Result.

Is the inspection result normal?

YES

>> INSPECTION END

>> Perform diagnosis of applicable DTC. Refer to

SRC-19, "DTC Index"

DTC

Display contents of

CONSULT

DTC detecting condition

Possible cause

B1210

SIDE COLLISION
DETECTION

Side air bag and curtain air bag and seat belt pre-
tensioner are deployed

—

Revision: 2011 October

2012 JUKE

B1212, B1213, B1214 SATELLITE SENSOR RH

SRC-141

< DTC/CIRCUIT DIAGNOSIS >

SRC

B1212, B1213, B1214 SATELLITE SENSOR RH

DTC Logic

INFOID:0000000007578373

DTC DETECTION LOGIC

DTC CONFIRMATION PROCEDURE

CHECK SELF-DIAG RESULT

With CONSULT

Turn ignition switch ON.

Perform “Self Diagnostic Result” mode of “AIR BAG” using CONSULT.

Without CONSULT

Turn ignition switch ON.

Check the air bag warning lamp status. Refer to

SRC-11, "On Board Diagnosis Function"

NOTE:
SRS does not enter the diagnosis mode if no malfunction is detected in the user mode.

Is malfunctioning part detected?

YES

>> Refer to

SRC-141, "Diagnosis Procedure"

>> INSPECTION END

Diagnosis Procedure

INFOID:0000000007578374

WARNING:

• Before servicing, turn ignition switch OFF, disconnect battery negative terminal, and wait at least 3

minutes or more. (To discharge backup capacitor.)

• Never use unspecified tester or other measuring device.

CHECK HARNESS CONNECTOR

Check the harness connector.

Is the inspection result normal?

YES

>> GO TO 2.

>> Replace harness connector.

CHECK WIRING HARNESS

Check the wiring harness externals.

Is the inspection result normal?

YES

>> GO TO 3.

>> Replace wiring harness.

REPLACE SATELLITE SENSOR

Replace satellite sensor RH. Refer to

SR-24, "Removal and Installation"

Perform DTC confirmation procedure. Refer to

SRC-141, "DTC Logic"

Is DTC detected?

YES

>> GO TO 4.

>> INSPECTION END

REPLACE AIR BAG DIAGNOSIS SENSOR UNIT

Replace air bag diagnosis sensor unit. Refer to

SR-27, "Removal and Installation"

Perform DTC confirmation procedure. Refer to

SRC-141, "DTC Logic"

Is DTC detected?

YES

>> GO TO 1.

DTC

Display contents of

CONSULT

DTC detecting condition

Possible cause

B1212
B1213
B1214

RH1 SAT-SENS

Satellite sensor RH is malfunctioning

• Harness or connectors
• Malfunction in satellite sensor RH
• Malfunction in air bag diagnosis sensor unit

Revision: 2011 October

2012 JUKE

B1215, B1216, B1217 SATELLITE SENSOR LH

SRC-143

< DTC/CIRCUIT DIAGNOSIS >

SRC

B1215, B1216, B1217 SATELLITE SENSOR LH

DTC Logic

INFOID:0000000007578375

DTC DETECTION LOGIC

DTC CONFIRMATION PROCEDURE

CHECK SELF-DIAG RESULT

With CONSULT

Turn ignition switch ON.

Perform “Self Diagnostic Result” mode of “AIR BAG” using CONSULT.

Without CONSULT

Turn ignition switch ON.

Check the air bag warning lamp status. Refer to

SRC-11, "On Board Diagnosis Function"

NOTE:
SRS does not enter the diagnosis mode if no malfunction is detected in the user mode.

Is malfunctioning part detected?

YES

>> Refer to

SRC-143, "Diagnosis Procedure"

>> INSPECTION END

Diagnosis Procedure

INFOID:0000000007578376

WARNING:

• Before servicing, turn ignition switch OFF, disconnect battery negative terminal, and wait at least 3

minutes or more. (To discharge backup capacitor.)

• Never use unspecified tester or other measuring device.

CHECK HARNESS CONNECTOR

Check the harness connector.

Is the inspection result normal?

YES

>> GO TO 2.

>> Replace harness connector.

CHECK WIRING HARNESS

Check the wiring harness externals.

Is the inspection result normal?

YES

>> GO TO 3.

>> Replace wiring harness.

REPLACE SATELLITE SENSOR

Replace satellite sensor LH. Refer to

SR-24, "Removal and Installation"

Perform DTC confirmation procedure. Refer to

SRC-143, "DTC Logic"

Is DTC detected?

YES

>> GO TO 4.

>> INSPECTION END

REPLACE AIR BAG DIAGNOSIS SENSOR UNIT

Replace air bag diagnosis sensor unit. Refer to

SR-27, "Removal and Installation"

Perform DTC confirmation procedure. Refer to

SRC-143, "DTC Logic"

Is DTC detected?

YES

>> GO TO 1.

DTC

Display contents of

CONSULT

DTC detecting condition

Possible cause

B1215
B1216
B1217

LH1 SAT-SENS

Satellite sensor LH is malfunctioning

• Harness or connectors
• Malfunction in satellite sensor LH
• Malfunction in air bag diagnosis sensor unit

Revision: 2011 October

2012 JUKE

B1218, B1219, B1220, B1221, B1222, B1223 DIAGNOSIS SENSOR UNIT

SRC-145

< DTC/CIRCUIT DIAGNOSIS >

SRC

B1218, B1219, B1220, B1221, B1222, B1223 DIAGNOSIS SENSOR UNIT

DTC Logic

INFOID:0000000007578377

DTC DETECTION LOGIC

DTC CONFIRMATION PROCEDURE

CHECK SELF-DIAG RESULT

With CONSULT

Turn ignition switch ON.

Perform “Self Diagnostic Result” mode of “AIR BAG” using CONSULT.

Without CONSULT

Turn ignition switch ON.

Check the air bag warning lamp status. Refer to

SRC-11, "On Board Diagnosis Function"

NOTE:
SRS does not enter the diagnosis mode if no malfunction is detected in the user mode.

Is malfunctioning part detected?

YES

>> Refer to

SRC-145, "Diagnosis Procedure"

>> INSPECTION END

Diagnosis Procedure

INFOID:0000000007578378

WARNING:

• Before servicing, turn ignition switch OFF, disconnect battery negative terminal, and wait at least 3

minutes or more. (To discharge backup capacitor.)

• Never use unspecified tester or other measuring device.

CHECK HARNESS CONNECTOR

Check the harness connector.

Is the inspection result normal?

YES

>> GO TO 2.

>> Replace harness connectors.

CHECK WIRING HARNESS

Check the wiring harness externals.
Is the inspection result normal?

YES

>> GO TO 3.

>> Replace wiring harness.

REPLACE AIR BAG DIAGNOSIS SENSOR UNIT

Replace air bag diagnosis sensor unit. Refer to

SR-27, "Removal and Installation"

Perform DTC confirmation procedure. Refer to

SRC-145, "DTC Logic"

Is DTC detected?

YES

>> GO TO 1.

>> INSPECTION END

DTC

Display contents of

CONSULT

DTC detecting condition

Possible cause

B1218
B1219
B1220
B1221
B1222
B1223

CONTROL UNIT

Air bag diagnosis sensor unit is malfunctioning

Malfunction in air bag diagnosis sensor unit

Revision: 2011 October

2012 JUKE

SRC-146

< DTC/CIRCUIT DIAGNOSIS >

B1234, B1235, B1236, B1237, B1238, B1239 DIAGNOSIS SENSOR UNIT

B1234, B1235, B1236, B1237, B1238, B1239 DIAGNOSIS SENSOR UNIT

DTC Logic

INFOID:0000000007578379

DTC DETECTION LOGIC

DTC CONFIRMATION PROCEDURE

CHECK SELF-DIAG RESULT

With CONSULT

Turn ignition switch ON.

Perform “Self Diagnostic Result” mode of “AIR BAG” using CONSULT.

Without CONSULT

Turn ignition switch ON.

Check the air bag warning lamp status. Refer to

SRC-11, "On Board Diagnosis Function"

NOTE:
SRS does not enter the diagnosis mode if no malfunction is detected in the user mode.

Is malfunctioning part detected?

YES

>> Refer to

SRC-146, "Diagnosis Procedure"

>> INSPECTION END

Diagnosis Procedure

INFOID:0000000007578380

WARNING:

• Before servicing, turn ignition switch OFF, disconnect battery negative terminal, and wait at least 3

minutes or more. (To discharge backup capacitor.)

• Never use unspecified tester or other measuring device.

CHECK HARNESS CONNECTOR

Check the harness connector.

Is the inspection result normal?

YES

>> GO TO 2.

>> Replace harness connectors.

CHECK WIRING HARNESS

Check the wiring harness externals.
Is the inspection result normal?

YES

>> GO TO 3.

>> Replace wiring harness.

REPLACE AIR BAG DIAGNOSIS SENSOR UNIT

Replace air bag diagnosis sensor unit. Refer to

SR-27, "Removal and Installation"

Perform DTC confirmation procedure. Refer to

SRC-146, "DTC Logic"

Is DTC detected?

YES

>> GO TO 1.

>> INSPECTION END

DTC

Display contents of

CONSULT

DTC detecting condition

Possible cause

B1234
B1235
B1236
B1237
B1238
B1239

CONTROL UNIT

Air bag diagnosis sensor unit is malfunctioning

Malfunction in air bag diagnosis sensor unit

Revision: 2011 October

2012 JUKE

B1336, B1337 SATELLITE SENSOR RH

SRC-147

< DTC/CIRCUIT DIAGNOSIS >

SRC

B1336, B1337 SATELLITE SENSOR RH

DTC Logic

INFOID:0000000007578381

DTC DETECTION LOGIC

DTC CONFIRMATION PROCEDURE

CHECK SELF-DIAG RESULT

With CONSULT

Turn ignition switch ON.

Perform “Self Diagnostic Result” mode of “AIR BAG” using CONSULT.

Without CONSULT

Turn ignition switch ON.

Check the air bag warning lamp status. Refer to

SRC-11, "On Board Diagnosis Function"

NOTE:
SRS does not enter the diagnosis mode if no malfunction is detected in the user mode.

Is malfunctioning part detected?

YES

>> Refer to

SRC-147, "Diagnosis Procedure"

>> INSPECTION END

Diagnosis Procedure

INFOID:0000000007578382

WARNING:

• Before servicing, turn ignition switch OFF, disconnect battery negative terminal, and wait at least 3

minutes or more. (To discharge backup capacitor.)

• Never use unspecified tester or other measuring device.

CHECK HARNESS CONNECTOR

Check the harness connector.

Is the inspection result normal?

YES

>> GO TO 2.

>> Replace harness connector.

CHECK WIRING HARNESS

Check the wiring harness externals.

Is the inspection result normal?

YES

>> GO TO 3.

>> Replace wiring harness.

REPLACE FRONT DOOR SATELLITE SENSOR

Replace front door satellite sensor RH. Refer to

SR-24, "Removal and Installation"

Perform DTC confirmation procedure. Refer to

SRC-147, "DTC Logic"

Is DTC detected?

YES

>> GO TO 4.

>> INSPECTION END

REPLACE AIR BAG DIAGNOSIS SENSOR UNIT

Replace air bag diagnosis sensor unit. Refer to

SR-27, "Removal and Installation"

Perform DTC confirmation procedure. Refer to

SRC-147, "DTC Logic"

Is DTC detected?

DTC

Display contents of CON-

SULT

DTC detecting condition

Possible cause

B1336
B1337

FR-RH DOOR SATEL
SENS
[SENSOR MALFUNC-
TION]

Front door satellite sensor RH is malfunc-
tioning

• Harness or connectors
• Malfunction in front door satellite sensor RH
• Malfunction in air bag diagnosis sensor unit

Revision: 2011 October

2012 JUKE

B1338, B1340, B1341, B1342 SATELLITE SENSOR RH

SRC-149

< DTC/CIRCUIT DIAGNOSIS >

SRC

B1338, B1340, B1341, B1342 SATELLITE SENSOR RH

DTC Logic

INFOID:0000000007578383

DTC DETECTION LOGIC

DTC CONFIRMATION PROCEDURE

CHECK SELF-DIAG RESULT

With CONSULT

Turn ignition switch ON.

Perform “Self Diagnostic Result” mode of “AIR BAG” using CONSULT.

Without CONSULT

Turn ignition switch ON.

Check the air bag warning lamp status. Refer to

SRC-11, "On Board Diagnosis Function"

NOTE:
SRS does not enter the diagnosis mode if no malfunction is detected in the user mode.

Is malfunctioning part detected?

YES

>> Refer to

SRC-149, "Diagnosis Procedure"

>> INSPECTION END

Diagnosis Procedure

INFOID:0000000007578384

WARNING:

• Before servicing, turn ignition switch OFF, disconnect battery negative terminal, and wait at least 3

minutes or more. (To discharge backup capacitor.)

• Never use unspecified tester or other measuring device.

CHECK HARNESS CONNECTOR

Check the harness connector.

Is the inspection result normal?

YES

>> GO TO 2.

>> Replace harness connector.

CHECK WIRING HARNESS

Check the wiring harness externals.

Is the inspection result normal?

YES

>> GO TO 3.

>> Replace wiring harness.

REPLACE FRONT DOOR SATELLITE SENSOR

Replace front door satellite sensor RH. Refer to

SR-24, "Removal and Installation"

Perform DTC confirmation procedure. Refer to

SRC-149, "DTC Logic"

Is DTC detected?

YES

>> GO TO 4.

>> INSPECTION END

REPLACE AIR BAG DIAGNOSIS SENSOR UNIT

Replace air bag diagnosis sensor unit. Refer to

SR-27, "Removal and Installation"

Perform DTC confirmation procedure. Refer to

SRC-149, "DTC Logic"

Is DTC detected?

DTC

Display contents of

CONSULT

DTC detecting condition

Possible cause

B1338
B1340
B1341
B1342

FR-RH DOOR SATEL
SENS
[COMM MALFUNC-
TION]

Front door satellite sensor RH is malfunc-
tioning

• Harness or connectors
• Malfunction in front door satellite sensor RH
• Malfunction in air bag diagnosis sensor unit

Revision: 2011 October

2012 JUKE

Nissan Juke (2012 year). Service Repair Manual - part 214