Nissan Juke (2012 year). Service Repair Manual - part 184

 

  Index      Manuals     Nissan Juke (2012 year) - Service and Repair Manual

 

Search            copyright infringement  

 

 

 

 

 

 

 

 

Content      ..     182      183      184      185     ..

 

 

Nissan Juke (2012 year). Service Repair Manual - part 184

 

 

PWC-32

< DTC/CIRCUIT DIAGNOSIS >

POWER WINDOW MOTOR

NO

>> Refer to 

PWC-32, "REAR RH : Diagnosis Procedure"

.

REAR RH : Diagnosis Procedure

INFOID:0000000007579906

1.

CHECK REAR POWER WINDOW MOTOR RH INPUT SIGNAL

1.

Turn ignition switch OFF.

2.

Disconnect rear power window motor RH connector.

3.

Turn ignition switch ON.

4.

Check voltage between rear power window motor RH harness connector and ground.

Is the inspection result normal?

YES

>> Replace rear power window motor RH.

NO

>> GO TO 2.

2.

CHECK REAR POWER WINDOW MOTOR RH CIRCUIT

1.

Turn ignition switch OFF.

2.

Disconnect rear power window switch RH connector.

3.

Check continuity between rear power window motor RH harness connector and rear power window switch
RH harness connector.

4.

Check continuity between rear power window motor RH harness connector and ground.

Is the inspection result normal?

YES

>> Replace rear power window switch RH.

NO

>> Repair or replace harness.

(+)

(-)

Condition

Voltage (V)

Rear power window motor RH

Connector

Terminal 

D47

1

Ground

Rear power window 
switch RH 

NEUTRAL

0 – 1

DOWN

9 – 16

3

NEUTRAL

0 – 1

UP

9 – 16

Rear power window motor RH

Rear power window switch RH

Continuity

Connector

Terminal

Connector

Terminal

D47

1

D43

4

Existed

3

5

Rear power window motor RH

Ground

Continuity

Connector

Terminal

D47

1

Not existed

3

Revision: 2011 October

2012 JUKE

ENCODER CIRCUIT

PWC-33

< DTC/CIRCUIT DIAGNOSIS >

C

D

E

F

G

H

I

J

L

M

A

B

PWC

N

O

P

ENCODER CIRCUIT

Component Function Check

INFOID:0000000007579907

1.

CHECK FUNCTION

Check that front driver side door glass perform AUTO UP/DOWN operation normally when power window
main switch is operated.

Is the inspection result normal?

YES

>> INSPECTION END

NO

>> Refer to 

PWC-33, "Diagnosis Procedure"

.

Diagnosis Procedure

INFOID:0000000007579908

1.

CHECK ENCODER PULSE SIGNAL

1.

Turn ignition switch ON.

2.

Check signal between power window main switch harness connector and ground with oscilloscope.

Is the inspection result normal?

YES

>> Replace power window main switch. Refer to 

PWC-48, "Removal and Installation"

.

NO

>> GO TO 2.

2.

CHECK ENCODER SIGNAL CIRCUIT

1.

Turn ignition switch OFF.

2.

Disconnect power window main switch connector and front power window motor (driver side) connector.

3.

Check continuity between power window main switch harness connector and front power window motor
(driver side) harness connector.

4.

Check continuity between power window main switch harness connector and ground.

Is the inspection result normal?

(+)

(-)

Signal

(Reference value)

 Power window main switch 

Connector

Terminal 

D35

4

Ground

Refer to the following signal

5

JMKIA5210GB

Power window main switch

Front power window motor (driver side)

Continuity

Connector

Terminal

Connector

Terminal

D35

4

D37

5

Existed

5

4

Power window main switch

Ground

Continuity

Connector

Terminal

D35

4

Not existed

5

Revision: 2011 October

2012 JUKE

PWC-34

< DTC/CIRCUIT DIAGNOSIS >

ENCODER CIRCUIT

YES

>> GO TO 3.

NO

>> Repair or replace harness.

3.

CHECK ENCODER POWER SUPPLY

1.

Connect power window main switch connector.

2.

Turn ignition switch ON.

3.

Check voltage between front power window motor (driver side) harness connector and ground.

Is the inspection result normal?

YES

>> GO TO 5.

NO

>> GO TO 4.

4.

CHECK ENCODER POWER SUPPLY CIRCUIT

1.

Turn ignition switch OFF.

2.

Disconnect power window main switch connector.

3.

Check continuity between power window main switch harness connector and front power window motor
(driver side) harness connector.

4.

Check continuity between power window main switch harness connector and ground.

Is the inspection result normal?

YES

>> Replace power window main switch. Refer to 

PWC-48, "Removal and Installation"

.

NO

>> Repair or replace harness.

5.

CHECK ENCODER GROUND CIRCUIT 1

1.

Turn ignition switch OFF.

2.

Disconnect power window main switch connector.

3.

Check continuity between power window main switch harness connector and front power window motor
(driver side) harness connector.

4.

Check continuity between power window main switch harness connector and ground.

Is the inspection result normal?

YES

>> GO TO 6.

NO

>> Repair or replace harness.

6.

CHECK ENCODER GROUND CIRCUIT 2

1.

Connect power window main switch connector.

(+)

(-)

Voltage (V)

Front power window motor (driver side)

Connector

Terminal 

D37

1

Ground

9 – 16

Power window main switch

Front power window motor (driver side)

Continuity

Connector

Terminal

Connector

Terminal

D35

14

D37

1

Existed

Power window main switch

Ground

Continuity

Connector

Terminal

D35

14

Not existed

Power window main switch

Front power window motor (driver side)

Continuity

Connector

Terminal

Connector

Terminal

D35

12

D37

6

Existed

Power window main switch

Ground

Continuity

Connector

Terminal

D35

12

Not existed

Revision: 2011 October

2012 JUKE

ENCODER CIRCUIT

PWC-35

< DTC/CIRCUIT DIAGNOSIS >

C

D

E

F

G

H

I

J

L

M

A

B

PWC

N

O

P

2.

Check continuity between power window main switch harness connector and ground.

Is the inspection result normal?

YES

>> Replace front power window motor (driver side).

NO

>> Replace power window main switch. Refer to 

PWC-48, "Removal and Installation"

.

Power window main switch

Ground

Continuity 

Connector

Terminal

D35

12

Existed

Revision: 2011 October

2012 JUKE

PWC-36

< SYMPTOM DIAGNOSIS >

NONE OF THE POWER WINDOWS CAN BE OPERATED USING ANY SWITCH

SYMPTOM DIAGNOSIS

NONE OF THE POWER WINDOWS CAN BE OPERATED USING ANY
SWITCH

Diagnosis Procedure

INFOID:0000000007579909

1.

CHECK BCM POWER SUPPLY AND GROUND CIRCUIT

Check BCM power supply and ground circuit. Refer to the following.
• With Intelligent Key: Refer to 

BCS-73, "Diagnosis Procedure"

.

• Without Intelligent Key: Refer to 

BCS-134, "Diagnosis Procedure"

.

Is the inspection result normal?

YES

>> GO TO 2.

NO

>> Repair or replace the malfunctioning parts.

2.

CHECK POWER WINDOW MAIN SWITCH POWER SUPPLY AND GROUND CIRCUIT

Check power window main switch power supply and ground circuit.
Refer to 

PWC-22, "POWER WINDOW MAIN SWITCH : Diagnosis Procedure"

.

Is the inspection result normal?

YES

>> GO TO 3.

NO

>> Repair or replace the malfunctioning parts.

3.

CONFIRM THE OPERATION

Confirm the operation again.

Is the result normal?

YES

>> Check intermittent incident. Refer to 

GI-43, "Intermittent Incident"

.

NO

>> GO TO 1.

Revision: 2011 October

2012 JUKE

DRIVER SIDE POWER WINDOW DOES NOT OPERATE

PWC-37

< SYMPTOM DIAGNOSIS >

C

D

E

F

G

H

I

J

L

M

A

B

PWC

N

O

P

DRIVER SIDE POWER WINDOW DOES NOT OPERATE

Diagnosis Procedure

INFOID:0000000007579910

1.

CHECK FRONT POWER WINDOW MOTOR (DRIVER SIDE)

Check front power window motor (driver side).
Refer to 

PWC-29, "DRIVER SIDE : Component Function Check"

.

Is the inspection result normal?

YES

>> GO TO 2.

NO

>> Repair or replace the malfunctioning parts.

2.

CONFIRM THE OPERATION

Confirm the operation again.

Is the result normal?

YES

>> Check intermittent incident. Refer to 

GI-43, "Intermittent Incident"

.

NO

>> GO TO 1.

Revision: 2011 October

2012 JUKE

PWC-38

< SYMPTOM DIAGNOSIS >

FRONT PASSENGER SIDE POWER WINDOW DOES NOT OPERATE

FRONT PASSENGER SIDE POWER WINDOW DOES NOT OPERATE

WHEN BOTH POWER WINDOW MAIN SWITCH AND FRONT POWER WINDOW
SWITCH ARE OPERATED

WHEN BOTH POWER WINDOW MAIN SWITCH AND FRONT POWER WINDOW 
SWITCH ARE OPERATED : Diagnosis Procedure

INFOID:0000000007579911

1.

CHECK FRONT POWER WINDOW SWITCH (PASSENGER SIDE)

Check front power window switch (passenger side).
Refer to 

PWC-25, "Component Function Check"

.

Is the inspection result normal?

YES

>> GO TO 2.

NO

>> Repair or replace the malfunctioning parts.

2.

CHECK FRONT POWER WINDOW MOTOR (PASSENGER SIDE)

Check front power window motor (passenger side).
Refer to 

PWC-30, "PASSENGER SIDE : Component Function Check"

.

Is the inspection result normal?

YES

>> GO TO 3.

NO

>> Repair or replace the malfunctioning parts.

3.

CONFIRM THE OPERATION

Confirm the operation again.
Is the result normal?

YES

>> Check intermittent incident. Refer to 

GI-43, "Intermittent Incident"

.

NO

>> GO TO 1.

WHEN FRONT POWER WINDOW SWITCH (PASSENGER SIDE) IS OPERATED

WHEN FRONT POWER WINDOW SWITCH (PASSENGER SIDE) IS OPERATED : 
Diagnosis Procedure

INFOID:0000000007579912

1.

CHECK FRONT POWER WINDOW SWITCH (PASSENGER SIDE) POWER SUPPLY AND GROUND CIR-

CUIT

Check front power window switch (passenger side) power supply and ground circuit.
Refer to 

PWC-23, "FRONT POWER WINDOW SWITCH (PASSENGER SIDE) : Diagnosis Procedure"

.

Is the inspection result normal?

YES

>> GO TO 2.

NO

>> Repair or replace the malfunctioning parts.

2.

CHECK FRONT POWER WINDOW SWITCH (PASSENGER SIDE)

Check front power window switch (passenger side).
Refer to 

PWC-25, "Component Function Check"

.

Is the inspection result normal?

YES

>> GO TO 3.

NO

>> Repair or replace the malfunctioning parts.

3.

CONFIRM THE OPERATION

Confirm the operation again.

Is the result normal?

YES

>> Check intermittent incident. Refer to 

GI-43, "Intermittent Incident"

.

NO

>> GO TO 1.

WHEN POWER WINDOW MAIN SWITCH IS OPERATED

Revision: 2011 October

2012 JUKE

FRONT PASSENGER SIDE POWER WINDOW DOES NOT OPERATE

PWC-39

< SYMPTOM DIAGNOSIS >

C

D

E

F

G

H

I

J

L

M

A

B

PWC

N

O

P

WHEN POWER WINDOW MAIN SWITCH IS OPERATED : Diagnosis Procedure

INFOID:0000000007579913

1.

CHECK FRONT POWER WINDOW SWITCH (PASSENGER SIDE)

Check front power window switch (passenger side).
Refer to 

PWC-25, "Component Function Check"

.

Is the inspection result normal?

YES

>> GO TO 2.

NO

>> Repair or replace the malfunctioning parts.

2.

CONFIRM THE OPERATION

Confirm the operation again.

Is the result normal?

YES

>> Check intermittent incident. Refer to 

GI-43, "Intermittent Incident"

.

NO

>> GO TO 1.

Revision: 2011 October

2012 JUKE

PWC-40

< SYMPTOM DIAGNOSIS >

REAR LH SIDE POWER WINDOW DOES NOT OPERATE

REAR LH SIDE POWER WINDOW DOES NOT OPERATE

WHEN BOTH POWER WINDOW MAIN SWITCH AND REAR POWER WINDOW
SWITCH LH ARE OPERATED

WHEN BOTH POWER WINDOW MAIN SWITCH AND REAR POWER WINDOW 
SWITCH LH ARE OPERATED : Diagnosis Procedure

INFOID:0000000007579914

1.

CHECK REAR POWER WINDOW SWITCH LH

Check rear power window switch LH.
Refer to 

PWC-27, "Component Function Check"

.

Is the inspection result normal?

YES

>> GO TO 2.

NO

>> Repair or replace the malfunctioning parts.

2.

CHECK REAR POWER WINDOW MOTOR LH

Check rear power window motor LH.
Refer to 

PWC-30, "REAR LH : Component Function Check"

.

Is the inspection result normal?

YES

>> GO TO 3.

NO

>> Repair or replace the malfunctioning parts.

3.

CONFIRM THE OPERATION

Confirm the operation again.
Is the result normal?

YES

>> Check intermittent incident. Refer to 

GI-43, "Intermittent Incident"

.

NO

>> GO TO 1.

WHEN REAR POWER WINDOW SWITCH LH IS OPERATED

WHEN REAR POWER WINDOW SWITCH LH IS OPERATED : Diagnosis Procedure

INFOID:0000000007579915

1.

CHECK REAR POWER WINDOW SWITCH LH POWER SUPPLY AND GROUND CIRCUIT

Check rear power window switch LH power supply and ground circuit.
Refer to 

PWC-23, "REAR POWER WINDOW SWITCH : Diagnosis Procedure"

.

Is the inspection result normal?

YES

>> GO TO 2.

NO

>> Repair or replace the malfunctioning parts.

2.

CHECK REAR POWER WINDOW SWITCH LH

Check rear power window switch LH.
Refer to 

PWC-27, "Component Function Check"

.

Is the inspection result normal?

YES

>> GO TO 3.

NO

>> Repair or replace the malfunctioning parts.

3.

CONFIRM THE OPERATION

Confirm the operation again.
Is the result normal?

YES

>> Check intermittent incident. Refer to 

GI-43, "Intermittent Incident"

.

NO

>> GO TO 1.

WHEN POWER WINDOW MAIN SWITCH IS OPERATED

Revision: 2011 October

2012 JUKE

REAR LH SIDE POWER WINDOW DOES NOT OPERATE

PWC-41

< SYMPTOM DIAGNOSIS >

C

D

E

F

G

H

I

J

L

M

A

B

PWC

N

O

P

WHEN POWER WINDOW MAIN SWITCH IS OPERATED : Diagnosis Procedure

INFOID:0000000007579916

1.

CHECK REAR POWER WINDOW SWITCH LH

Check rear power window switch LH.
Refer to 

PWC-27, "Component Function Check"

.

Is the inspection result normal?

YES

>> GO TO 2.

NO

>> Repair or replace the malfunctioning parts.

2.

CONFIRM THE OPERATION

Confirm the operation again.

Is the result normal?

YES

>> Check intermittent incident. Refer to 

GI-43, "Intermittent Incident"

.

NO

>> GO TO 1.

Revision: 2011 October

2012 JUKE

PWC-42

< SYMPTOM DIAGNOSIS >

REAR RH SIDE POWER WINDOW DOES NOT OPERATE

REAR RH SIDE POWER WINDOW DOES NOT OPERATE

WHEN BOTH POWER WINDOW MAIN SWITCH AND REAR POWER WINDOW
SWITCH RH ARE OPERATED

WHEN BOTH POWER WINDOW MAIN SWITCH AND REAR POWER WINDOW 
SWITCH RH ARE OPERATED : Diagnosis Procedure

INFOID:0000000007579917

1.

CHECK REAR POWER WINDOW SWITCH RH

Check rear power window switch RH.
Refer to 

PWC-27, "Component Function Check"

.

Is the inspection result normal?

YES

>> GO TO 2.

NO

>> Repair or replace the malfunctioning parts.

2.

CHECK REAR POWER WINDOW MOTOR RH

Check rear power window motor RH.
Refer to 

PWC-31, "REAR RH : Component Function Check"

.

Is the inspection result normal?

YES

>> GO TO 3.

NO

>> Repair or replace the malfunctioning parts.

3.

CONFIRM THE OPERATION

Confirm the operation again.
Is the result normal?

YES

>> Check intermittent incident. Refer to 

GI-43, "Intermittent Incident"

.

NO

>> GO TO 1.

WHEN REAR POWER WINDOW SWITCH RH IS OPERATED

WHEN REAR POWER WINDOW SWITCH RH IS OPERATED : Diagnosis Procedure

INFOID:0000000007579918

1.

CHECK REAR POWER WINDOW SWITCH RH POWER SUPPLY AND GROUND CIRCUIT

Check rear power winodw switch RH power supply and ground circuit. 
Refer to 

PWC-23, "REAR POWER WINDOW SWITCH : Diagnosis Procedure"

.

Is the inspection result normal?

YES

>> GO TO 2.

NO

>> Repair or replace the malfunctioning parts.

2.

CHECK REAR POWER WINDOW SWITCH RH

Check rear power window switch RH. 
Refer to 

PWC-27, "Component Function Check"

.

Is the inspection result normal?

YES

>> GO TO 3.

NO

>> Repair or replace the malfunctioning parts.

3.

CONFIRM THE OPERATION

Confirm the operation again.
Is the result normal?

YES

>> Check intermittent incident. Refer to 

GI-43, "Intermittent Incident"

.

NO

>> GO TO 1.

WHEN POWER WINDOW MAIN SWITCH IS OPERATED

Revision: 2011 October

2012 JUKE

REAR RH SIDE POWER WINDOW DOES NOT OPERATE

PWC-43

< SYMPTOM DIAGNOSIS >

C

D

E

F

G

H

I

J

L

M

A

B

PWC

N

O

P

WHEN POWER WINDOW MAIN SWITCH IS OPERATED : Diagnosis Procedure

INFOID:0000000007579919

1.

CHECK REAR POWER WINDOW SWITCH RH

Check rear power window switch RH.
Refer to 

PWC-27, "Component Function Check"

.

Is the inspection result normal?

YES

>> GO TO 2.

NO

>> Repair or replace the malfunctioning parts.

2.

CONFIRM THE OPERATION

Confirm the operation again.

Is the result normal?

YES

>> Check intermittent incident. Refer to 

GI-43, "Intermittent Incident"

.

NO

>> GO TO 1.

Revision: 2011 October

2012 JUKE

PWC-44

< SYMPTOM DIAGNOSIS >

AUTO OPERATION DOES NOT OPERATE BUT MANUAL OPERATE NORMAL-

LY (DRIVER SIDE)

AUTO OPERATION DOES NOT OPERATE BUT MANUAL OPERATE NOR-
MALLY (DRIVER SIDE)

Diagnosis Procedure

INFOID:0000000007579920

1.

PERFORM INITIALIZATION PROCEDURE

Initialization procedure is executed and operation is confirmed.
Refer to 

PWC-20, "Work Procedure"

.

Is the inspection result normal?

YES

>> INSPECTION END

NO

>> GO TO 2.

2.

CHECK ENCODER CIRCUIT

Check encoder circuit.
Refer to 

PWC-33, "Component Function Check"

.

Is the inspection result normal?

YES

>> GO TO 3.

NO

>> Repair or replace the malfunctioning parts.

3.

CONFIRM THE OPERATION

Confirm the operation again.

Is the result normal?

YES

>> Check intermittent incident. Refer to 

GI-43, "Intermittent Incident"

.

NO

>> GO TO 1.

Revision: 2011 October

2012 JUKE

ANTI-PINCH SYSTEM DOES NOT OPERATE NORMALLY (DRIVER SIDE)

PWC-45

< SYMPTOM DIAGNOSIS >

C

D

E

F

G

H

I

J

L

M

A

B

PWC

N

O

P

ANTI-PINCH SYSTEM DOES NOT OPERATE NORMALLY (DRIVER SIDE)

Diagnosis Procedure

INFOID:0000000007579921

1.

CHECK POWER WINDOW AUTO OPERATION

Check AUTO operation when anti-pinch function does not operate.
Is the inspection result normal?

YES

>> GO TO 2.

NO

>> Refer to 

PWC-44, "Diagnosis Procedure"

.

2.

CONFIRM THE OPERATION

Confirm the operation again.
Is the result normal?

YES

>> Check intermittent incident. Refer to 

GI-43, "Intermittent Incident"

.

NO

>> GO TO 1.

Revision: 2011 October

2012 JUKE

PWC-46

< SYMPTOM DIAGNOSIS >

POWER WINDOW RETAINED POWER OPERATION DOES NOT OPERATE 

PROPERLY

POWER WINDOW RETAINED POWER OPERATION DOES NOT OPER-
ATE PROPERLY

Diagnosis Procedure

INFOID:0000000007579922

1.

CHECK FRONT DOOR SWITCH

Check front door switch. Refer to the following.
• With Intelligent Key: Refer to 

DLK-71, "Component Function Check"

.

• Without Intelligent Key: Refer to 

DLK-201, "Component Function Check"

.

Is the inspection result normal?

YES

>> GO TO 2.

NO

>> Repair or replace the malfunctioning parts.

2.

CONFIRM THE OPERATION

Confirm the operation again.

Is the result normal?

YES

>> Check intermittent incident. Refer to 

GI-43, "Intermittent Incident"

.

NO

>> GO TO 1.

Revision: 2011 October

2012 JUKE

POWER WINDOW LOCK SWITCH DOES NOT FUNCTION

PWC-47

< SYMPTOM DIAGNOSIS >

C

D

E

F

G

H

I

J

L

M

A

B

PWC

N

O

P

POWER WINDOW LOCK SWITCH DOES NOT FUNCTION

Diagnosis Procedure

INFOID:0000000007579923

1.

REPLACE POWER WINDOW MAIN SWITCH 

Replace power window main switch. 

>> Refer to 

PWC-48, "Removal and Installation"

.

Revision: 2011 October

2012 JUKE

 

 

 

 

 

 

 

Content      ..     182      183      184      185     ..