Nissan Juke (2012 year). Service Repair Manual - part 173

 

  Index      Manuals     Nissan Juke (2012 year) - Service and Repair Manual

 

Search            copyright infringement  

 

 

 

 

 

 

 

 

Content      ..     171      172      173      174     ..

 

 

Nissan Juke (2012 year). Service Repair Manual - part 173

 

 

PCS-52

< WIRING DIAGRAM >

[IPDM E/R (WITHOUT I-KEY)]

IPDM E/R

WIRING DIAGRAM

IPDM E/R

Wiring Diagram

INFOID:0000000007579362

For connector terminal arrangements, harness layouts, and alphabets in a 

 (option abbreviation; if not

described in wiring diagram), refer to 

GI-12, "Connector Information"

.

JRMWC5514GB

Revision: 2011 October

2012 JUKE

PCS

IPDM E/R

PCS-53

< WIRING DIAGRAM >

[IPDM E/R (WITHOUT I-KEY)]

C

D

E

F

G

H

I

J

K

L

B

A

O

P

N

JRMWC5515GB

Revision: 2011 October

2012 JUKE

PCS-54

< WIRING DIAGRAM >

[IPDM E/R (WITHOUT I-KEY)]

IPDM E/R

JRMWC5516GB

Revision: 2011 October

2012 JUKE

PCS

U1000 CAN COMM CIRCUIT

PCS-55

< DTC/CIRCUIT DIAGNOSIS >

[IPDM E/R (WITHOUT I-KEY)]

C

D

E

F

G

H

I

J

K

L

B

A

O

P

N

DTC/CIRCUIT DIAGNOSIS

U1000 CAN COMM CIRCUIT

Description

INFOID:0000000007579363

CAN (Controller Area Network) is a serial communication line for real time applications. It is an on-vehicle mul-
tiplex communication line with high data communication speed and excellent error detection ability. Modern
vehicle is equipped with many electronic control unit, and each control unit shares information and links with
other control units during operation (not independent). In CAN communication, control units are connected
with 2 communication lines (CAN-H line, CAN-L line) allowing a high rate of information transmission with less
wiring. Each control unit transmits/receives data but selectively reads required data only.
CAN Communication Signal Chart. Refer to 

LAN-28, "CAN COMMUNICATION SYSTEM : CAN Communica-

tion Signal Chart"

.

DTC Logic

INFOID:0000000007579364

DTC DETECTION LOGIC

Diagnosis Procedure

INFOID:0000000007579365

1.

PERFORM SELF DIAGNOSTIC

1.

Turn the ignition switch ON and wait for 2 seconds or more.

2.

Check “Self Diagnostic Result” of IPDM E/R.

Is DTC “U1000” displayed?

YES

>> Refer to 

LAN-15, "Trouble Diagnosis Flow Chart"

.

NO

>> Refer to 

GI-43, "Intermittent Incident"

.

DTC

CONSULT display de-

scription

DTC Detection Condition

Possible cause

U1000

CAN COMM CIRCUIT

When IPDM E/R cannot communicate CAN communi-
cation signal continuously for 2 seconds or more

CAN communication system

Revision: 2011 October

2012 JUKE

PCS-56

< DTC/CIRCUIT DIAGNOSIS >

[IPDM E/R (WITHOUT I-KEY)]

B2098 IGNITION RELAY ON STUCK

B2098 IGNITION RELAY ON STUCK

Description

INFOID:0000000007579366

The ignition relay integrated in IPDM E/R is operated with ignition switch ON signal from the ignition switch.

DTC Logic

INFOID:0000000007579367

DTC DETECTION LOGIC

1.

PERFORM DTC CONFIRMATION PROCEDURE

1.

Turn ignition switch ON.

2.

Check DTC in “Self Diagnostic Result” mode of “IPDM E/R” using CONSULT.

Is DTC detected?

YES

>> Refer to 

PCS-56, "Diagnosis Procedure"

.

NO

>> INSPECTION END.

Diagnosis Procedure

INFOID:0000000007579368

1.

CHECK IGNITION SWITCH ON SIGNAL

Check voltage between BCM harness connectors and the ground.

Is the measurement value normal?

YES

>> Replace BCM. Refer to 

BCS-141, "Removal and Installation"

.

NO

>> GO TO 2.

2.

CHECK IGNITION SWITCH ON SIGNAL CIRCUIT

1.

Turn the ignition switch OFF.

2.

Disconnect IPDM E/R harness connectors.

3.

Check continuity between IPDM E/R harness connectors and BCM harness connectors.

Does continuity exist?

YES

>> Replace IPDM E/R. Refer to 

PCS-59, "Removal and Installation"

.

NO

>> Repair the harness or connector.

DTC

CONSULT display de-

scription

DTC Detection Condition

Possible causes

B2098

IGN RELAY ON

The ignition relay ON is detected for 1 second at ignition switch 
OFF
(CPU monitors the status at the contact circuits of the ignition re-
lay inside and ignition switch status from BCM via CAN commu-
nication)

• IPDM E/R
• BCM
• Harness or connector 

(Ignition relay circuit)

(+)

(–)

Condition

Voltage

(Approx.)

BCM

Connector

Terminal

M65

38

Ground

Ignition switch

ON

Battery voltage

OFF

0 V

IPDM E/R

BCM

Continuity

Connector

Terminal

Connector

Terminal

E12

22

M65

38

Existed

Revision: 2011 October

2012 JUKE

PCS

B2099 IGNITION RELAY OFF STUCK

PCS-57

< DTC/CIRCUIT DIAGNOSIS >

[IPDM E/R (WITHOUT I-KEY)]

C

D

E

F

G

H

I

J

K

L

B

A

O

P

N

B2099 IGNITION RELAY OFF STUCK

Description

INFOID:0000000007579369

The ignition relay integrated in IPDM E/R is operated with ignition switch ON signal from the ignition switch.

DTC Logic

INFOID:0000000007579370

DTC DETECTION LOGIC

NOTE:

When IPDM E/R power supply voltage is low (Approx. 7 - 8 V for about 1 second), the “DTC: B2099” may be detected.

1.

PERFORM DTC CONFIRMATION PROCEDURE

1.

Turn ignition switch ON.

2.

Check DTC in “Self Diagnostic Result” mode of “IPDM E/R” using CONSULT.

Is DTC detected?

YES

>> Refer to 

PCS-57, "Diagnosis Procedure"

.

NO

>> INSPECTION END.

Diagnosis Procedure

INFOID:0000000007579371

1.

CHECK IGNITION SWITCH ON SIGNAL CIRCUIT

1.

Turn the ignition switch OFF.

2.

Disconnect IPDM E/R harness connector and BCM harness connector.

3.

Check continuity between IPDM E/R harness connectors and BCM harness connectors.

Does continuity exist?

YES

>> Replace IPDM E/R. Refer to 

PCS-59, "Removal and Installation"

.

NO

>> Repair the harness or connector.

DTC

CONSULT display 

description

DTC Detection Condition

Possible causes

B2099

IGN RELAY OFF

The ignition relay OFF is detected for 1 second at ignition switch ON
(CPU monitors the status at the contact circuits of the ignition relay 
inside and ignition switch status from BCM via CAN communication)

• IPDM  E/R
• Harness or connector

(Ignition relay circuit)

IPDM E/R

BCM

Continuity

Connector

Terminal

Connector

Terminal

E12

22

M65

38

Existed

Revision: 2011 October

2012 JUKE

PCS-58

< DTC/CIRCUIT DIAGNOSIS >

[IPDM E/R (WITHOUT I-KEY)]

POWER SUPPLY AND GROUND CIRCUIT

POWER SUPPLY AND GROUND CIRCUIT

Diagnosis Procedure

INFOID:0000000007579372

1.

CHECK FUSES AND FUSIBLE LINK

Check that the following IPDM E/R fuses or fusible links are not blown.

Is the fuse fusing?

YES

>> Replace the blown fuse or fusible link after repairing the affected circuit if a fuse or fusible link is

blown.

NO

>> GO TO 2.

2.

CHECK POWER SUPPLY CIRCUIT

1.

Turn the ignition switch OFF.

2.

Disconnect IPDM E/R connector.

3.

Check voltage between IPDM E/R harness connector and the ground.

Is the measurement value normal?

YES

>> GO TO 3.

NO

>> Repair the harness or connector.

3.

CHECK GROUND CIRCUIT

Check continuity between IPDM E/R harness connectors and the ground.

Does continuity exist?

YES

>> INSPECTION END

NO

>> Repair the harness or connector.

Signal name

Fuses and fusible link No.

Battery power supply

C

D

(+)

(

)

Voltage

(Approx.)

IPDM E/R

Connector

Terminal

E9

1

Ground

6 – 16 V

2

IPDM E/R

Ground

Continuity

Connector

Terminal

E11

9

Existed

E12

18

Revision: 2011 October

2012 JUKE

PCS

IPDM E/R

PCS-59

< REMOVAL AND INSTALLATION >

[IPDM E/R (WITHOUT I-KEY)]

C

D

E

F

G

H

I

J

K

L

B

A

O

P

N

REMOVAL AND INSTALLATION

IPDM E/R

Exploded View

INFOID:0000000007579373

Removal and Installation

INFOID:0000000007579374

CAUTION:

IPDM E/R integrated relays are not serviceable parts, and must not be removed from the unit.

REMOVAL

1.

Remove battery.

2.

Press and expand pawls (A) on lateral side of IPDM E/R cover and remove IPDM E/R (1) from IPDM E/R
cover B (2).

3.

Disconnect the harness connector and then remove the IPDM
E/R.

4.

Remove IPDM E/R cover B mounting nuts (A).

1.

IPDM E/R cover A

2.

IPDM E/R

3.

IPDM E/R cover B

JMMIA0458ZZ

JMMIA0459ZZ

JMMIA0460ZZ

Revision: 2011 October

2012 JUKE

PCS-60

< REMOVAL AND INSTALLATION >

[IPDM E/R (WITHOUT I-KEY)]

IPDM E/R

5.

Insert a flat-bladed screwdriver between IPDM E/R cover A (1)
and IPDM E/R cover B (2), disengage pawls, and remove IPDM
E/R cover A.

6.

Remove IPDM E/R cover B.

INSTALLATION

Install in the reverse order of removal.

JMMIA0461ZZ

Revision: 2011 October

2012 JUKE

PCS

PRECAUTIONS

PCS-61

< PRECAUTION >

[POWER DISTRIBUTION SYSTEM]

C

D

E

F

G

H

I

J

K

L

B

A

O

P

N

PRECAUTION

PRECAUTIONS

Precaution for Supplemental Restraint System (SRS) "AIR BAG" and "SEAT BELT 
PRE-TENSIONER"

INFOID:0000000007772467

The Supplemental Restraint System such as “AIR BAG” and “SEAT BELT PRE-TENSIONER”, used along
with a front seat belt, helps to reduce the risk or severity of injury to the driver and front passenger for certain
types of collision. This system includes seat belt switch inputs and dual stage front air bag modules. The SRS
system uses the seat belt switches to determine the front air bag deployment, and may only deploy one front
air bag, depending on the severity of a collision and whether the front occupants are belted or unbelted.
Information necessary to service the system safely is included in the “SRS AIR BAG” and “SEAT BELT” of this
Service Manual.

WARNING:

Always observe the following items for preventing accidental activation.
• To avoid rendering the SRS inoperative, which could increase the risk of personal injury or death in

the event of a collision that would result in air bag inflation, all maintenance must be performed by
an authorized NISSAN/INFINITI dealer.

• Improper maintenance, including incorrect removal and installation of the SRS, can lead to personal

injury caused by unintentional activation of the system. For removal of Spiral Cable and Air Bag
Module, see “SRS AIR BAG”.

• Never use electrical test equipment on any circuit related to the SRS unless instructed to in this Ser-

vice Manual. SRS wiring harnesses can be identified by yellow and/or orange harnesses or harness
connectors.

PRECAUTIONS WHEN USING POWER TOOLS (AIR OR ELECTRIC) AND HAMMERS

WARNING:

Always observe the following items for preventing accidental activation.
• When working near the Air Bag Diagnosis Sensor Unit or other Air Bag System sensors with the

ignition ON or engine running, never use air or electric power tools or strike near the sensor(s) with
a hammer. Heavy vibration could activate the sensor(s) and deploy the air bag(s), possibly causing
serious injury.

• When using air or electric power tools or hammers, always switch the ignition OFF, disconnect the

battery, and wait at least 3 minutes before performing any service.

Precaution for Procedure without Cowl Top Cover

INFOID:0000000007772468

When performing the procedure after removing cowl top cover, cover
the lower end of windshield with urethane, etc to prevent damage to
windshield.

PIIB3706J

Revision: 2011 October

2012 JUKE

PCS-62

< SYSTEM DESCRIPTION >

[POWER DISTRIBUTION SYSTEM]

COMPONENT PARTS

SYSTEM DESCRIPTION

COMPONENT PARTS

Component Parts Location

INFOID:0000000007579377

Component Description

INFOID:0000000007579378

BCM

INFOID:0000000007579379

BCM controls the various electrical components and simultaneously supplies power according to the power
supply position.
BCM checks the power supply position internally.

Ignition Relay

INFOID:0000000007579380

BCM turns ON the following relays to supply ignition power supply or ignition switch ON signal to each ECU
when the ignition switch is turned ON.
• Ignition relay (fuse block)
• Ignition relay (IPDM E/R)
• Blower relay

1.

Push-button ignition switch

2.

IPDM E/R
Refer to 

PCS-5, "Component Parts 

Location"

3.

Transmission range switch
Refer to 

TM-69, "CVT CONTROL 

SYSTEM : Component Parts Loca-
tion"

4.

Stop lamp switch
Refer to 

BRC-8, "Component Parts 

Location"

5.

Clutch interlock switch
Refer to 

STR-5, "STARTING SYS-

TEM (WITH INTELLIGENT KEY) : 
Component Parts Location"

6.

BCM
Refer to 

BCS-6, "BODY CONTROL 

SYSTEM : Component Parts Loca-
tion"

JMMIA0638ZZ

BCM

Reference

BCM

PCS-62

Ignition relay

PCS-62

Accessory relay

PCS-63

Blower relay

PCS-63

Push-button ignition switch

PCS-63

Stop lamp switch

PCS-63

Transmission range switch

PCS-63

Clutch interlock switch

PCS-63

Revision: 2011 October

2012 JUKE

PCS

COMPONENT PARTS

PCS-63

< SYSTEM DESCRIPTION >

[POWER DISTRIBUTION SYSTEM]

C

D

E

F

G

H

I

J

K

L

B

A

O

P

N

BCM compares following status comparing.
• Ignition relay (fuse block) control signal, and power supply position judged by BCM
• Ignition relay (IPDM E/R) control request, and Ignition relay (IPDM E/R) status

Accessory Relay

INFOID:0000000007579381

BCM turns ON the accessory relays to supply accessory power supply or ignition switch ACC signal to each
ECU when the ignition switch is turned ACC or ON.
BCM compares status of accessory relay control signal, and power supply position judged by BCM.

Blower Relay

INFOID:0000000007579382

BCM turns ON the following relays to supply ignition power supply or ignition switch ON signal to each ECU
when the ignition switch is turned ON.
• Ignition relay (fuse block)
• Ignition relay (IPDM E/R)
• Blower relay
BCM compares status of blower relay control signal, and power supply position judged by BCM.

Push-Button Ignition Switch

INFOID:0000000007579383

BCM transmits the change in the power supply position with the push-button ignition switch to IPDM E/R via
CAN communication line. IPDM E/R transmits the power supply position status via CAN communication line to
BCM.

Stop Lamp Switch

INFOID:0000000007579384

Stop lamp switch detects that brake pedal is depressed, and then transmits the signal to BCM.

Transmission Range Switch

INFOID:0000000007579385

Transmission range switch is integrated in CVT assembly, and detects the CVT shift selector position.
Transmission range switch detects selector lever position (P/N position), and transmits the P/N position signal
to BCM.

Clutch Interlock Switch

INFOID:0000000007579386

Clutch interlock switch detects that clutch pedal is depressed, and transmits ON/OFF signal to BCM.

Revision: 2011 October

2012 JUKE

PCS-64

< SYSTEM DESCRIPTION >

[POWER DISTRIBUTION SYSTEM]

SYSTEM

SYSTEM

POWER DISTRIBUTION SYSTEM

POWER DISTRIBUTION SYSTEM : System Diagram

INFOID:0000000007579387

POWER DISTRIBUTION SYSTEM : System Description

INFOID:0000000007579388

SYSTEM DESCRIPTION

• PDS (POWER DISTRIBUTION SYSTEM) is the system that BCM controls with the operation of the push-

button ignition switch and performs the power distribution to each power circuit. This system is used instead
of the mechanical power supply changing mechanism with the operation of the conventional key cylinder.

• The push-button ignition switch can be operated when Intelligent Key is in the following condition. Refer to

Engine Start Function for details.

- Intelligent Key is in the detection area of the inside key antenna.
- Intelligent Key backside is contacted to push-button ignition switch.
• The push-button ignition switch operation is input to BCM as a signal. BCM changes the power supply posi-

tion according to the status and operates the following relays to supply power to each power circuit.

- Ignition relay (IPDM E/R)
- Ignition relay (fuse block)
- ACC relay
- Blower relay

NOTE:
The push-button ignition switch operation changes due to the conditions of brake pedal, selector lever and
vehicle speed.

• The power supply position can be confirmed with the lighting of ACC/ON indicator in the push-button ignition

switch.

BATTERY SAVER SYSTEM

When all the following conditions are met for 60 minutes, the battery saver system will cut off the power supply
to prevent battery discharge.
• The ignition switch is in the ACC position
• All doors are closed
• Selector lever is in the P position (except M/T models)

Reset Condition of Battery Saver System

CVT models
In order to prevent the battery from discharging, the battery saver system will cut off the power supply when all
doors are closed, the selector lever is on P position (except M/T models) and the ignition switch is left on ACC
position for 60 minutes. If any of the following conditions are met the battery saver system is released and the
steering will change automatically to lock position from OFF position.
• Opening any door
• Operating with request switch on door lock

JMMIA0639GB

Revision: 2011 October

2012 JUKE

PCS

SYSTEM

PCS-65

< SYSTEM DESCRIPTION >

[POWER DISTRIBUTION SYSTEM]

C

D

E

F

G

H

I

J

K

L

B

A

O

P

N

• Operating with Intelligent Key on door lock
Press push-button ignition switch and ignition switch will change to ACC position from OFF position.
M/T models
If any of the conditions above is met the battery saver system is released.

POWER SUPPLY POSITION CHANGE TABLE BY PUSH-BUTTON IGNITION SWITCH OPERA-
TION

The power supply position changing operation can be performed with the following operations.
NOTE:
• When an Intelligent Key is within the detection area of inside key antenna and when Intelligent Key backside

is contacted to push-button ignition switch, it is equivalent to the operations below.

• When starting the engine, the BCM monitors under the engine start conditions,

CVT models

- Brake pedal operating condition
- Selector lever position
- Vehicle speed

M/T models

- Clutch pedal operating condition
- Vehicle speed

Vehicle speed: less than 4 km/h (2.5 MPH)

Vehicle speed: 4 km/h (2.5 MPH) or more

Emergency stop operation

• Press and hold the push-button ignition switch for 2 seconds or more.

• Press the push-button ignition switch 3 times or more within 1.5 seconds.

Fail-safe

INFOID:0000000007579389

FAIL-SAFE CONTROL BY DTC

BCM performs fail-safe control when any DTC are detected.

Power supply position

Engine start/stop condition

Push-button ignition switch 

operation frequency

CVT models

M/T models

Selector lever position

Brake pedal operation 

condition

Clutch pedal operation 

condition

OFF 

 ACC

Not depressed

Not depressed

1

OFF 

 ACC 

 ON

Not depressed

Not depressed

2

OFF 

 ACC 

 ON 

 OFF

Not depressed

Not depressed

3

OFF 

 START

ACC 

 START

ON 

 START

P or N position

Depressed

Depressed

1

Engine is running 

 OFF

1

Power supply position

Engine start/stop condition

Push-button ignition switch 

operation frequency

CVT models

M/T models

Selector lever position

Brake pedal operation 

condition

Clutch pedal opera-

tion condition

Engine is running 

 ACC 

Emergency stop operation

Engine stall return operation 
while driving 

N position

Not depressed

Depressed

1

Display contents of CONSULT

Fail-safe

Cancellation

B2013: ID DISCORD BCM-S/L

Inhibit engine cranking

When communication between BCM and steering lock unit are commu-
nicated normally.

B2014: CHAIN OF S/L-BCM

Inhibit engine cranking

When communication between BCM and steering lock unit are commu-
nicated normally.

Revision: 2011 October

2012 JUKE

PCS-66

< SYSTEM DESCRIPTION >

[POWER DISTRIBUTION SYSTEM]

SYSTEM

REAR WIPER MOTOR PROTECTION

BCM detects the rear wiper stopping position according to the rear wiper stop position signal.
When the rear wiper stop position signal does not change for more than 5 seconds while driving the rear
wiper, BCM stops power supply to protect the rear wiper motor.

Condition of cancellation

1.

More than 1 minute is passed after the rear wiper stop.

2.

Turn rear wiper switch OFF.

3.

Operate the rear wiper switch or rear washer switch.

FAIL-SAFE CONTROL OF COMBINATION SWITCH READING FUNCTION CAUSED BY LOW
POWER SUPPLY VOLTAGE

If voltage of battery power supply lower, BCM maintains combination switch reading to the status when input
voltage is less than approximately 9 V.
NOTE:
When voltage of battery power supply is approximately 9 V or more, combination switch reading function
returns to normal operation.

B2192: ID DISCORD BCM-ECM

Inhibit engine cranking

Erase DTC

B2193: CHAIN OF BCM-ECM

Inhibit engine cranking

Erase DTC

B2195: ANTI-SCANNING

Inhibit engine cranking

Ignition switch ON 

 OFF

B2196: DONGLE NG

Inhibit engine cranking

Erase DTC

B2198: NATS ANTENNA AMP

Inhibit engine cranking

Erase DTC

B2608: STARTER RELAY

Inhibit engine cranking

500 ms after the following signal communication status becomes con-
sistent
• Starter motor relay control signal
• Starter relay status signal (CAN)

B260F: ENG STATE SIG LOST

Inhibit engine cranking

When any of the following conditions are fulfilled
• Power position changes to ACC
• Receives engine status signal (CAN)

B2619: BCM

Inhibit engine cranking

1 second after the steering lock unit power supply output control inside 
BCM becomes normal

B26F1: IGN RELAY OFF

Inhibit engine cranking

When the following conditions are fulfilled
• Ignition switch ON signal (CAN: Transmitted from BCM): ON
• Ignition switch ON signal (CAN: Transmitted from IPDM E/R): ON

B26F2: IGN RELAY ON

Inhibit engine cranking

When the following conditions are fulfilled
• Ignition switch ON signal (CAN: Transmitted from BCM): OFF
• Ignition switch ON signal (CAN: Transmitted from IPDM E/R): OFF

B26F3: START CONT RLY ON

Inhibit engine cranking

When the following conditions are fulfilled
• Starter control relay signal (CAN: Transmitted from BCM): OFF
• Starter control relay signal (CAN: Transmitted from IPDM E/R): OFF

B26F4: START CONT RLY OFF

Inhibit engine cranking

When the following conditions are fulfilled
• Starter control relay signal (CAN: Transmitted from BCM): ON
• Starter control relay signal (CAN: Transmitted from IPDM E/R): ON

B26F7: BCM

Inhibit engine cranking 
by Intelligent Key sys-
tem

When room antenna and luggage room antenna functions normally

Display contents of CONSULT

Fail-safe

Cancellation

Revision: 2011 October

2012 JUKE

PCS

DIAGNOSIS SYSTEM (BCM)

PCS-67

< SYSTEM DESCRIPTION >

[POWER DISTRIBUTION SYSTEM]

C

D

E

F

G

H

I

J

K

L

B

A

O

P

N

DIAGNOSIS SYSTEM (BCM)

COMMON ITEM

COMMON ITEM : CONSULT Function (BCM - COMMON ITEM)

INFOID:0000000007773660

APPLICATION ITEM

CONSULT performs the following functions via CAN communication with BCM.

SYSTEM APPLICATION

BCM can perform the following functions for each system.
NOTE:
It can perform the diagnosis modes except the following for all sub system selection items.

×

: Applicable item

NOTE:

*: For models with automatic A/C, this diagnosis mode is not used.

FREEZE FRAME DATA (FFD)

The BCM records the following vehicle condition at the time a particular DTC is detected, and displays on
CONSULT.

Diagnosis mode

Function Description

Work Support

Changes the setting for each system function.

Self Diagnostic Result

Displays the diagnosis results judged by BCM.

CAN Diag Support Monitor

Monitors the reception status of CAN communication viewed from BCM.

Data Monitor

The BCM input/output signals are displayed.

Active Test

The signals used to activate each device are forcibly supplied from BCM.

Ecu Identification

The BCM part number is displayed.

Configuration

• Read and save the vehicle specification.
• Write the vehicle specification when replacing BCM.

System

Sub system selection item

Diagnosis mode

Work Support

Data Monitor

Active Test

Door lock

DOOR LOCK

×

×

×

Rear window defogger

REAR DEFOGGER

×

×

Warning chime

BUZZER

×

×

Interior room lamp timer

INT LAMP

×

×

×

Exterior lamp

HEAD LAMP

×

×

×

Wiper and washer

WIPER

×

×

×

Turn signal and hazard warning lamps

FLASHER

×

×

×

Air conditioning system

AIR CONDITONER

×

×

*

• Intelligent Key system
• Engine start system

INTELLIGENT KEY

×

×

×

Combination switch

COMB SW

×

Body control system

BCM

×

NVIS - NATS

IMMU

×

×

×

Interior room lamp battery saver

BATTERY SAVER

×

×

×

Back door open

TRUNK

×

Theft warning alarm

THEFT ALM

×

×

×

RAP

RETAINED PWR

×

Signal buffer system

SIGNAL BUFFER

×

×

TPMS

AIR PRESSURE MONITOR

×

×

×

Revision: 2011 October

2012 JUKE

 

 

 

 

 

 

 

Content      ..     171      172      173      174     ..