Nissan Juke (2012 year). Service Repair Manual - part 154

INSTRUMENT PANEL ASSEMBLY

IP-15

< REMOVAL AND INSTALLATION >

C

D

E

F

G

H

I

K

L

M

A

B

IP

N

O

P

1.

Remove center console fixing screws (A).

2.

Remove seat heated switch harness clip (with seat heated switch).

3.

Lift up center console assembly back side.

CAUTION:

Be careful not for damaging parts in surrounding area.

8.

Release front pillar portion of front body side welt LH. Refer to 

INT-20, "BODY SIDE WELT : Removal and

Installation"

.

9.

Remove front pillar garnish LH. Refer to 

INT-17, "FRONT PILLAR GARNISH : Removal and Installation"

.

10. Remove instrument side finisher LH.

1.

Insert remover tool (A) between instrument side finisher LH
and instrument panel assembly to disengage the pawls as
shown in the figure.

2.

Pull back instrument side finisher LH.

CAUTION:

Apply protective tape (B) on the part to protect it from dam-
age.

11. Remove instrument lower panel LH.

1.

Remove hood opener and fuel lid opener lever. Refer to 

DLK-147, "HOOD LOCK CONTROL CABLE

: Removal and Installation"

.

2.

Remove fixing screw (A).

3.

Pull back instrument lower panel LH, and then disengage
the pawls and metal clips.

4.

Disconnect harness connectors and aspirator duct.

12. Remove driver air bag module. Refer to 

SR-10, "Removal and Installation"

.

13. Remove steering wheel. Refer to 

ST-8, "Removal and Installation"

.

14. Remove steering column covers.

1.

Place the tilt to the lowest level.

JMJIA4553ZZ

: Pawl

JMJIA4554ZZ

: Pawl

: Metal clip

JMJIA4556ZZ

Revision: 2011 October

2012 JUKE

IP-16

< REMOVAL AND INSTALLATION >

INSTRUMENT PANEL ASSEMBLY

2.

Remove steering lock escutcheon (1). (without Intelligent
Key)

3.

Remove fixing screws (A).

4.

Pull up steering column upper cover (2), and then disen-
gage steering column upper cove fixing pawls.

5.

Remove steering column upper cover.

6.

Pull down the steering column lower cover (2), and then
remove steering column lower cover.

NOTE:
Disengage the pawls, and then remove steering lock escutch-
eon (4). (with Intelligent Key)

15. Remove spiral cable. Refer to 

SR-13, "Removal and Installation"

.

16. Remove combination switch. Refer to 

BCS-81, "Removal and Installation"

.

17. Remove cluster lid A.

1.

Cover steering shaft with a shop cloth (A) to prevent dam-
age.

2.

Pull back cluster lid A while holding the lower side and dis-
engage the metal clips underside.

3.

Hold both upper sides of cluster lid A and pull it out towards
vehicle rear, and disengage pawl and metal clips topside.

4.

Disconnect push-button ignition switch harness connector
and NATS antenna amp.harness connector. (with Intelligent
Key)

CAUTION:

Remove metal clips slowly so that they are not damaged.

18. Remove combination meter. Refer to 

MWI-53, "Removal and Installation"

.

19. Remove multi display unit (with auto A/C) or A/C finisher (with manual A/C).

: Pawl

JMJIA4189ZZ

: Pawl

: Metal clip

JMJIA4557ZZ

1.

Multi display unit (with auto A/C)

2.

Instrument panel assembly
(with auto A/C models)

3.

Intake door lever knob

4.

A/C finisher (with manual A/C)

5.

Instrument panel assembly
(with manual A/C models)

: Pawl

: Metal clip

JMJIA4558ZZ

Revision: 2011 October

2012 JUKE

INSTRUMENT PANEL ASSEMBLY

IP-17

< REMOVAL AND INSTALLATION >

C

D

E

F

G

H

I

K

L

M

A

B

IP

N

O

P

Multi display unit (with auto A/C)

1.

Apply protective tape (B) on instrument panel assembly (2) to protect it from damage.

2.

Insert a remover tool (A) into the cutouts at the bottom of
multi display unit (1), then pull straight back to disengage
the pawls and metals clips.

3.

Pull back multi display unit, and then disconnect harness connector.

A/C finisher (with manual A/C)

1.

Apply a protective tape (B) on instrument panel assembly (5) to protect it from damage.

2.

Hold intake door lever knob (1) from upper side and lower
side, tilt it to the right and the left, and then disengage it
from intake door lever (2). Pull up intake door lever knob
and remove it from intake door lever.

3.

Insert a remover tool (A) into the cutouts at the bottom of multi display unit (4), then pull straight back
to disengage pawls and metal clips.

4.

Pull back A/C finisher.

20. Remove A/C control fixing screws (with Manual A/C). Refer to 

HAC-134, "Removal and Installation"

.

: Pawl

: Metal clip

JMJIA6909ZZ

JMJIA6910ZZ

Revision: 2011 October

2012 JUKE

IP-18

< REMOVAL AND INSTALLATION >

INSTRUMENT PANEL ASSEMBLY

21. Remove cluster lid C.

1.

Remove fixing screws (A).

2.

Pull back cluster lid C, and disengage the pawls and metal
clips.

3.

Disconnect harness connector.

22. Remove audio unit or NAVI C/U.

• Audio unit: Refer to 

AV-59, "Removal and Installation"

.

• NAVI C/U: Refer to 

AV-120, "Removal and Installation"

.

23. Disconnect hazard switch harness connector.

24. Remove cluster tray.

1.

Insert a remover tool (A) between cluster tray and instru-
ment panel assembly, and then pull downward and disen-
gage metal clips.

2.

Pull back cluster tray.

3.

Disconnect harness connectors.

CAUTION:

Apply protective tape (B) on the part to protect it from dam-
age.

25. Release front pillar portion of front body side welt RH. Refer to 

INT-20, "BODY SIDE WELT : Removal and

Installation"

.

26. Remove front pillar garnish RH. Refer to 

INT-17, "FRONT PILLAR GARNISH : Removal and Installation"

.

27. Remove instrument side finisher RH.

1.

Insert remover tool (A) between instrument side finisher RH
and instrument panel assembly to disengage the pawls as
shown in the figure.

2.

Pull back instrument side finisher RH.

CAUTION:

Apply protective tape (B) on the part to protect it from dam-
age.

28. Remove glove box lid.

1.

Open glove box lid.

2.

Pull glove box lid (1) toward vehicle rear, and then disen-
gage the joint from instrument panel assembly (2).

: Pawl

: Metal clip

JMJIA4559ZZ

: Metal clip

JMJIA4560ZZ

: Pawl

JMJIA4561ZZ

JMJIA4563ZZ

Revision: 2011 October

2012 JUKE

INSTRUMENT PANEL ASSEMBLY

IP-19

< REMOVAL AND INSTALLATION >

C

D

E

F

G

H

I

K

L

M

A

B

IP

N

O

P

3.

Disengage the pawl, and then remove damper pin on right
side.

CAUTION:

Never excessively pull string of glove box damper.

29. Remove glove box assembly.

1.

Remove fixing screws (A).

2.

Pull back the glove box cover assembly while holding the lower side and disengage the pawls.

30. Remove passenger air bag module. Refer to 

SR-16, "Removal and Installation"

.

31. Remove switch panel.

1.

Insert remover tool (A) between switch panel and instru-
ment panel assembly to disengage the pawls as shown in
the figure.

2.

Pull up switch panel, and then disconnect harness connec-
tors.

CAUTION:

Apply protective tape (B) on the part to protect it from dam-
age.

32. Remove instrument panel assembly.

: Pawl

JMJIA4564ZZ

: Pawl

JMJIA4565ZZ

: Pawl

JMJIA4566ZZ

Revision: 2011 October

2012 JUKE

IP-20

< REMOVAL AND INSTALLATION >

INSTRUMENT PANEL ASSEMBLY

1.

Remove instrument panel assembly mounting screws (A) and bolts (B).

CAUTION:

Cover tool with a shop cloth to prevent windshield glass from being damaged.

2.

Disengage harness (A) and harness (B) of front pillar LH and RH portions from instrument panel
assembly.

3.

Remove instrument panel from passenger door opening portion.

CAUTION:

• Cover CVT shift selector upper surface with a shop cloth to prevent it from being damaged.
• When removing instrument panel assembly, 2 workers are required to prevent it from drop-

ping.

33. Remove the following parts after removing instrument panel assembly.

• Side defroster nozzle: Refer to

VTL-8, "SIDE DEFROSTER NOZZLE : Removal and Installation"

.

• Side defroster grille: Refer to 

VTL-9, "SIDE DEFROSTER GRILLE : Removal and Installation"

.

• Side ventilator grille: Refer to 

VTL-8, "SIDE VENTILATOR GRILLE : Removal and Installation"

.

• Front defroster nozzle: Refer to 

VTL-9, "FRONT DEFROSTER NOZZLE : Removal and Installation"

.

• Center ventilator duct: Refer to 

VTL-10, "CENTER VENTILATOR DUCT : Removal and Installation"

.

• Side ventilator duct: Refer to 

VTL-10, "SIDE VENTILATOR DUCT : Removal and Installation"

.

• GPS antenna: Refer to 

AV-126, "Removal and Installation"

.

• Hazard switch: Refer to 

EXL-89, "Removal and Installation"

.

INSTALLATION

Note the following item, and then install in the reverse order of removal.

CAUTION:

• After installation, adjust the parking brake lever stroke. Refer to 

PB-3, "Inspection and Adjustment"

.

• Never use the steering wheel mounting nut after removal, replace with the new nut.
• Never use the driver air bag module mounting bolts after removal, replace with the new bolts.
• Never use the passenger air bag module mounting bolts after removal, replace with the new bolts.

JMJIA4567ZZ

JMJIA4568ZZ

Revision: 2011 October

2012 JUKE

CENTER CONSOLE ASSEMBLY

IP-21

< REMOVAL AND INSTALLATION >

C

D

E

F

G

H

I

K

L

M

A

B

IP

N

O

P

CENTER CONSOLE ASSEMBLY

Exploded View

INFOID:0000000007577876

CVT models

JMJIA4498ZZ

1.

Console indicator finisher

2.

Instrument lower cover RH

3.

Center console assembly

4.

Instrument lower cover LH

5.

Instrument stay

6.

CVT shift selector assembly

7.

Console rear bracket

8.

Console rear finisher

9.

Seat heated switch

10. Console switch finisher

11.

Console switch finisher

12. Console finisher assembly

13. Console mask

14. Console front bracket

: Pawl

: Metal clip

Revision: 2011 October

2012 JUKE

IP-22

< REMOVAL AND INSTALLATION >

CENTER CONSOLE ASSEMBLY

MT models

Removal and Installation

INFOID:0000000007577877

WARNING:

Before servicing, turn ignition switch OFF, disconnect battery negative terminal and wait 3 minutes or
more.

REMOVAL

CAUTION:

When removing, always use a remover tool that is made of plastic.

JMJIA4497ZZ

1.

Console boot

2.

Instrument lower cover RH

3.

Center console assembly

4.

Instrument lower cover LH

5.

Instrument stay

6.

Console center bracket

7.

Console rear bracket

8.

Console rear finisher

9.

Seat heated switch

10. Console switch finisher

11.

Console switch finisher

12. Console finisher assembly

13. Console mask

14. Console front bracket

: Pawl

: Metal clip

Revision: 2011 October

2012 JUKE

CENTER CONSOLE ASSEMBLY

IP-23

< REMOVAL AND INSTALLATION >

C

D

E

F

G

H

I

K

L

M

A

B

IP

N

O

P

1.

Remove shift lever knob (MT models only). Refer to 

TM-20, "Removal and Installation"

.

2.

Remove console finisher assembly.
1.

Put selector lever in “N” position.

2.

Loosen the parking brake lever stroke by turning the adjusting nut with a socket wrench. Refer to 

PB-

3, "Inspection and Adjustment"

.

3.

Lift up console finisher assembly in numerical order shown in the figure and disengage metal clips.

4.

Remove console finisher assembly while pulling it towards vehicle rear.

CAUTION:

• Be careful not for damaging parts in surrounding area.
• Remove metal clips slowly so that they are not damaged.

3.

Remove console rear finisher. 
1.

Put front seat assembly (LH and RH) to frontmost position.

2.

Pull back console rear finisher, and disengage the pawls
and metal clips.

: Metal clip

JMJIA4550ZZ

: Pawl

: Metal clip

JMJIA4183ZZ

Revision: 2011 October

2012 JUKE

IP-24

< REMOVAL AND INSTALLATION >

CENTER CONSOLE ASSEMBLY

4.

Remove center console assembly fixing screws (A).

5.

Remove instrument lower cover LH.
1.

Put front seat assembly LH to rearmost position.

2.

Remove fixing clip (A).

3.

Pull the instrument lower cover LH crosswise, and disen-
gage the pawl and metal clips.

CAUTION:

Remove pawl and metal clips slowly so that they are not
damaged.

6.

Remove instrument lower cover RH.
1.

Put front seat assembly RH to rearmost position.

2.

Remove fixing clip (A).

3.

Pull the instrument lower cover RH crosswise, and disen-
gage the pawl and metal clips.

CAUTION:

Remove pawl and metal clips slowly so that they are not
damaged.

7.

Remove center console assembly.

1.

Remove center console fixing screws (A).

2.

Lift up center console assembly back side.

CAUTION:

Be careful not for damaging parts in surrounding area.

INSTALLATION

Note the following item, and then install in the reverse order of removal.

CAUTION:

After installation, adjust the parking brake lever stroke. Refer to 

PB-3, "Inspection and Adjustment"

.

JMJIA4202ZZ

: Pawl

: Metal clip

JMJIA4551ZZ

: Pawl

: Metal clip

JMJIA4552ZZ

JMJIA4553ZZ

Revision: 2011 October

2012 JUKE

CENTER CONSOLE ASSEMBLY

IP-25

< REMOVAL AND INSTALLATION >

C

D

E

F

G

H

I

K

L

M

A

B

IP

N

O

P

Disassembly and Assembly

INFOID:0000000007577878

Disassembly and Assembly of Console Finisher Assembly

CAUTION:

When disassembling, always use a remover tool that is made of plastic.

DISASSEMBLY

1.

Remove console finisher assembly. Refer to 

IP-22, "Removal and Installation"

.

2.

Remove console indicator finisher (CVT models)
Disengage connection of the console indicator finisher (2) fixing
pawls from the inside of the console finisher assembly (1)
toward the outside, and remove.

3.

Remove console indicator finisher (MT models)
Disengage connection of the console boot (2) fixing pawls from
the inside of the console finisher assembly (1) toward the out-
side, and remove.

4.

Remove console switch finisher.
Disengage connection of the console switch finisher (2) fixing
pawls from the inside of the console finisher assembly (1)
toward the outside, and remove.
NOTE:
Remove seat heated switch. Refer to 

SE-35, "Removal and

Installation"

.

ASSEMBLY

Assemble in the reverse order of disassembly.

: Pawl

JMJIA4204ZZ

: Pawl

JMJIA4573ZZ

: Pawl

JMJIA4574ZZ

Revision: 2011 October

2012 JUKE

LAN

LAN-1

ELECTRICAL & POWER CONTROL

C

D

E

F

G

H

I

J

K

L

B

SECTION 

LAN

A

O

P

N

CONTENTS

LAN SYSTEM

CAN FUNDAMENTAL

PRECAUTION ...............................................

5

PRECAUTIONS ...................................................

5

Precautions for Trouble Diagnosis  ............................

5

Precautions for Harness Repair  ................................

5

SYSTEM DESCRIPTION  ..............................

6

SYSTEM ..............................................................

6

CAN COMMUNICATION SYSTEM .............................

6

CAN COMMUNICATION SYSTEM : System De-
scription .....................................................................

6

DIAG ON CAN  .............................................................

6

DIAG ON CAN : Description  .....................................

6

DIAG ON CAN : System Diagram  .............................

6

TROUBLE DIAGNOSIS  ......................................

8

System Diagram ........................................................

8

Condition of Error Detection ......................................

8

Symptom When Error Occurs in CAN Communi-
cation System ............................................................

9

CAN Diagnosis with CONSULT  ..............................

11

Self-Diagnosis .........................................................

12

CAN Diagnostic Support Monitor  ............................

12

How to Use CAN Communication Signal Chart  ......

14

BASIC INSPECTION  ...................................

15

DIAGNOSIS AND REPAIR WORKFLOW  .........

15

Trouble Diagnosis Flow Chart  .................................

15

Trouble Diagnosis Procedure ..................................

15

CAN

HOW TO USE THIS MANUAL .....................

20

HOW TO USE THIS SECTION ...........................

20

Caution ....................................................................

20

Abbreviation List ......................................................

20

PRECAUTION ..............................................

21

PRECAUTIONS .................................................

21

Precaution for Supplemental Restraint System 
(SRS) "AIR BAG" and "SEAT BELT PRE-TEN-
SIONER" .................................................................

21

Precautions for Trouble Diagnosis  ..........................

21

Precautions for Harness Repair  ..............................

21

SYSTEM DESCRIPTION  .............................

23

COMPONENT PARTS  ......................................

23

Component Parts Location  ......................................

23

SYSTEM ............................................................

24

CAN COMMUNICATION SYSTEM ............................

24

CAN COMMUNICATION SYSTEM : System Dia-
gram ........................................................................

24

CAN COMMUNICATION SYSTEM : System De-
scription ...................................................................

24

CAN COMMUNICATION SYSTEM : CAN Com-
munication Control Circuit  .......................................

26

CAN COMMUNICATION SYSTEM : CAN System 
Specification Chart  ..................................................

27

CAN COMMUNICATION SYSTEM : CAN Com-
munication Signal Chart  ..........................................

28

WIRING DIAGRAM  ......................................

32

CAN SYSTEM  ...................................................

32

Wiring Diagram ........................................................

32

BASIC INSPECTION  ...................................

33

DIAGNOSIS AND REPAIR WORKFLOW  ........

33

Interview Sheet ........................................................

33

DTC/CIRCUIT DIAGNOSIS  .........................

34

MALFUNCTION AREA CHART ........................

34

Main Line  .................................................................

34

Branch Line  .............................................................

34

Revision: 2011 October

2012 JUKE

LAN-2

Short Circuit  ............................................................

34

MAIN LINE BETWEEN IPDM-E AND DLC 
CIRCUIT .............................................................

35

Diagnosis Procedure  ..............................................

35

MAIN LINE BETWEEN DLC AND A-BAG CIR-
CUIT ...................................................................

36

Diagnosis Procedure  ..............................................

36

MAIN LINE BETWEEN DLC AND MDU CIR-
CUIT ...................................................................

37

Diagnosis Procedure  ..............................................

37

ECM BRANCH LINE CIRCUIT  ..........................

38

Diagnosis Procedure  ..............................................

38

4WD BRANCH LINE CIRCUIT  ..........................

39

Diagnosis Procedure  ..............................................

39

ABS BRANCH LINE CIRCUIT  ..........................

40

Diagnosis Procedure  ..............................................

40

IPDM-E BRANCH LINE CIRCUIT  .....................

41

Diagnosis Procedure  ..............................................

41

TCM BRANCH LINE CIRCUIT  ..........................

42

Diagnosis Procedure  ..............................................

42

DLC BRANCH LINE CIRCUIT ...........................

43

Diagnosis Procedure  ..............................................

43

EPS BRANCH LINE CIRCUIT  ...........................

44

Diagnosis Procedure  ..............................................

44

M&A BRANCH LINE CIRCUIT  ..........................

45

Diagnosis Procedure  ..............................................

45

STRG BRANCH LINE CIRCUIT  ........................

46

Diagnosis Procedure  ..............................................

46

A-BAG BRANCH LINE CIRCUIT  ......................

47

Diagnosis Procedure  ..............................................

47

HVAC BRANCH LINE CIRCUIT  ........................

48

Diagnosis Procedure  ..............................................

48

MDU BRANCH LINE CIRCUIT  ..........................

49

Diagnosis Procedure  ..............................................

49

BCM BRANCH LINE CIRCUIT  ..........................

50

Diagnosis Procedure  ..............................................

50

CAN COMMUNICATION CIRCUIT ....................

51

Diagnosis Procedure  ..............................................

51

CAN SYSTEM (TYPE  1)

DTC/CIRCUIT DIAGNOSIS .........................

53

MAIN LINE BETWEEN IPDM-E AND DLC 
CIRCUIT .............................................................

53

Diagnosis Procedure  ..............................................

53

MAIN LINE BETWEEN DLC AND A-BAG CIR-
CUIT ...................................................................

54

Diagnosis Procedure ...............................................

54

ECM BRANCH LINE CIRCUIT  ..........................

55

Diagnosis Procedure ...............................................

55

ABS BRANCH LINE CIRCUIT  ..........................

56

Diagnosis Procedure ...............................................

56

IPDM-E BRANCH LINE CIRCUIT  .....................

57

Diagnosis Procedure ...............................................

57

DLC BRANCH LINE CIRCUIT  ..........................

58

Diagnosis Procedure ...............................................

58

EPS BRANCH LINE CIRCUIT ...........................

59

Diagnosis Procedure ...............................................

59

M&A BRANCH LINE CIRCUIT ..........................

60

Diagnosis Procedure ...............................................

60

STRG BRANCH LINE CIRCUIT  ........................

61

Diagnosis Procedure ...............................................

61

A-BAG BRANCH LINE CIRCUIT  ......................

62

Diagnosis Procedure ...............................................

62

BCM BRANCH LINE CIRCUIT ..........................

63

Diagnosis Procedure ...............................................

63

CAN COMMUNICATION CIRCUIT  ...................

64

Diagnosis Procedure ...............................................

64

CAN SYSTEM (TYPE  2)

DTC/CIRCUIT DIAGNOSIS ........................

66

MAIN LINE BETWEEN IPDM-E AND DLC 
CIRCUIT .............................................................

66

Diagnosis Procedure ...............................................

66

MAIN LINE BETWEEN DLC AND MDU CIR-
CUIT ...................................................................

67

Diagnosis Procedure ...............................................

67

ECM BRANCH LINE CIRCUIT  ..........................

68

Diagnosis Procedure ...............................................

68

ABS BRANCH LINE CIRCUIT  ..........................

69

Diagnosis Procedure ...............................................

69

IPDM-E BRANCH LINE CIRCUIT  .....................

70

Diagnosis Procedure ...............................................

70

DLC BRANCH LINE CIRCUIT  ..........................

71

Diagnosis Procedure ...............................................

71

EPS BRANCH LINE CIRCUIT ...........................

72

Diagnosis Procedure ...............................................

72

M&A BRANCH LINE CIRCUIT ..........................

73

Diagnosis Procedure ...............................................

73

Revision: 2011 October

2012 JUKE

LAN

LAN-3

C

D

E

F

G

H

I

J

K

L

B

A

O

P

N

STRG BRANCH LINE CIRCUIT .........................

74

Diagnosis Procedure ...............................................

74

A-BAG BRANCH LINE CIRCUIT  .......................

75

Diagnosis Procedure ...............................................

75

HVAC BRANCH LINE CIRCUIT  ........................

76

Diagnosis Procedure ...............................................

76

MDU BRANCH LINE CIRCUIT  ..........................

77

Diagnosis Procedure ...............................................

77

BCM BRANCH LINE CIRCUIT  ..........................

78

Diagnosis Procedure ...............................................

78

CAN COMMUNICATION CIRCUIT  ....................

79

Diagnosis Procedure ...............................................

79

CAN SYSTEM (TYPE  3)

DTC/CIRCUIT DIAGNOSIS  .........................

81

MAIN LINE BETWEEN IPDM-E AND DLC 
CIRCUIT .............................................................

81

Diagnosis Procedure ...............................................

81

MAIN LINE BETWEEN DLC AND A-BAG CIR-
CUIT ....................................................................

82

Diagnosis Procedure ...............................................

82

ECM BRANCH LINE CIRCUIT ...........................

83

Diagnosis Procedure ...............................................

83

ABS BRANCH LINE CIRCUIT  ...........................

84

Diagnosis Procedure ...............................................

84

IPDM-E BRANCH LINE CIRCUIT  ......................

85

Diagnosis Procedure ...............................................

85

TCM BRANCH LINE CIRCUIT  ...........................

86

Diagnosis Procedure ...............................................

86

DLC BRANCH LINE CIRCUIT  ...........................

87

Diagnosis Procedure ...............................................

87

EPS BRANCH LINE CIRCUIT  ...........................

88

Diagnosis Procedure ...............................................

88

M&A BRANCH LINE CIRCUIT  ..........................

89

Diagnosis Procedure ...............................................

89

STRG BRANCH LINE CIRCUIT .........................

90

Diagnosis Procedure ...............................................

90

A-BAG BRANCH LINE CIRCUIT  .......................

91

Diagnosis Procedure ...............................................

91

BCM BRANCH LINE CIRCUIT  ..........................

92

Diagnosis Procedure ...............................................

92

CAN COMMUNICATION CIRCUIT  ....................

93

Diagnosis Procedure ...............................................

93

CAN SYSTEM (TYPE  4)

DTC/CIRCUIT DIAGNOSIS  .........................

95

MAIN LINE BETWEEN IPDM-E AND DLC 
CIRCUIT ............................................................

95

Diagnosis Procedure  ...............................................

95

MAIN LINE BETWEEN DLC AND MDU CIR-
CUIT ..................................................................

96

Diagnosis Procedure  ...............................................

96

ECM BRANCH LINE CIRCUIT  .........................

97

Diagnosis Procedure  ...............................................

97

ABS BRANCH LINE CIRCUIT ..........................

98

Diagnosis Procedure  ...............................................

98

IPDM-E BRANCH LINE CIRCUIT  .....................

99

Diagnosis Procedure  ...............................................

99

TCM BRANCH LINE CIRCUIT ........................

100

Diagnosis Procedure  .............................................

100

DLC BRANCH LINE CIRCUIT  ........................

101

Diagnosis Procedure  .............................................

101

EPS BRANCH LINE CIRCUIT  ........................

102

Diagnosis Procedure  .............................................

102

M&A BRANCH LINE CIRCUIT  .......................

103

Diagnosis Procedure  .............................................

103

STRG BRANCH LINE CIRCUIT  .....................

104

Diagnosis Procedure  .............................................

104

A-BAG BRANCH LINE CIRCUIT ....................

105

Diagnosis Procedure  .............................................

105

HVAC BRANCH LINE CIRCUIT  .....................

106

Diagnosis Procedure  .............................................

106

MDU BRANCH LINE CIRCUIT  .......................

107

Diagnosis Procedure  .............................................

107

BCM BRANCH LINE CIRCUIT  .......................

108

Diagnosis Procedure  .............................................

108

CAN COMMUNICATION CIRCUIT  .................

109

Diagnosis Procedure  .............................................

109

CAN SYSTEM (TYPE  5)

DTC/CIRCUIT DIAGNOSIS  .......................

111

MAIN LINE BETWEEN IPDM-E AND DLC 
CIRCUIT ..........................................................

111

Diagnosis Procedure  .............................................

111

MAIN LINE BETWEEN DLC AND A-BAG CIR-
CUIT ................................................................

112

Diagnosis Procedure  .............................................

112

ECM BRANCH LINE CIRCUIT  .......................

113

Diagnosis Procedure  .............................................

113

Revision: 2011 October

2012 JUKE

LAN-4

4WD BRANCH LINE CIRCUIT  ........................

114

Diagnosis Procedure  .............................................

114

ABS BRANCH LINE CIRCUIT  ........................

115

Diagnosis Procedure  .............................................

115

IPDM-E BRANCH LINE CIRCUIT  ...................

116

Diagnosis Procedure  .............................................

116

TCM BRANCH LINE CIRCUIT  ........................

117

Diagnosis Procedure  .............................................

117

DLC BRANCH LINE CIRCUIT .........................

118

Diagnosis Procedure  .............................................

118

EPS BRANCH LINE CIRCUIT  .........................

119

Diagnosis Procedure  .............................................

119

M&A BRANCH LINE CIRCUIT  ........................

120

Diagnosis Procedure  .............................................

120

STRG BRANCH LINE CIRCUIT  ......................

121

Diagnosis Procedure  .............................................

121

A-BAG BRANCH LINE CIRCUIT  ....................

122

Diagnosis Procedure  .............................................

122

BCM BRANCH LINE CIRCUIT  ........................

123

Diagnosis Procedure  .............................................

123

CAN COMMUNICATION CIRCUIT ..................

124

Diagnosis Procedure  .............................................

124

CAN SYSTEM (TYPE  6)

DTC/CIRCUIT DIAGNOSIS ........................

126

MAIN LINE BETWEEN IPDM-E AND DLC 
CIRCUIT ...........................................................

126

Diagnosis Procedure  .............................................

126

MAIN LINE BETWEEN DLC AND MDU CIR-
CUIT .................................................................

127

Diagnosis Procedure  .............................................

127

ECM BRANCH LINE CIRCUIT  .........................

128

Diagnosis Procedure .............................................

128

4WD BRANCH LINE CIRCUIT  .........................

129

Diagnosis Procedure .............................................

129

ABS BRANCH LINE CIRCUIT  .........................

130

Diagnosis Procedure .............................................

130

IPDM-E BRANCH LINE CIRCUIT  ....................

131

Diagnosis Procedure .............................................

131

TCM BRANCH LINE CIRCUIT  .........................

132

Diagnosis Procedure .............................................

132

DLC BRANCH LINE CIRCUIT  .........................

133

Diagnosis Procedure .............................................

133

EPS BRANCH LINE CIRCUIT ..........................

134

Diagnosis Procedure .............................................

134

M&A BRANCH LINE CIRCUIT .........................

135

Diagnosis Procedure .............................................

135

STRG BRANCH LINE CIRCUIT  .......................

136

Diagnosis Procedure .............................................

136

A-BAG BRANCH LINE CIRCUIT  .....................

137

Diagnosis Procedure .............................................

137

HVAC BRANCH LINE CIRCUIT .......................

138

Diagnosis Procedure .............................................

138

MDU BRANCH LINE CIRCUIT .........................

139

Diagnosis Procedure .............................................

139

BCM BRANCH LINE CIRCUIT .........................

140

Diagnosis Procedure .............................................

140

CAN COMMUNICATION CIRCUIT  ..................

141

Diagnosis Procedure .............................................

141

Revision: 2011 October

2012 JUKE

LAN

PRECAUTIONS

LAN-5

< PRECAUTION >

[CAN FUNDAMENTAL]

C

D

E

F

G

H

I

J

K

L

B

A

O

P

N

PRECAUTION

PRECAUTIONS

Precautions for Trouble Diagnosis

INFOID:0000000007578584

CAUTION:

• Never apply 7.0 V or more to the measurement terminal.
• Use a tester with open terminal voltage of 7.0 V or less.
• Turn the ignition switch OFF and disconnect the battery cable from the negative terminal when

checking the harness. 

Precautions for Harness Repair

INFOID:0000000007578585

• Solder the repaired area and wrap tape around the soldered area.

NOTE:
A fray of twisted lines must be within 110 mm (4.33 in).

• Bypass connection is never allowed at the repaired area.

NOTE:
Bypass connection may cause CAN communication error. The
spliced wire becomes separated and the characteristics of twisted
line are lost. 

• Replace the applicable harness as an assembly if error is detected on the shield lines of CAN communica-

tion line.

SKIB8766E

SKIB8767E

Revision: 2011 October

2012 JUKE